Search Documents

By Qing-hua Tian, Xue-yi Guo, Fei Li

A novel process for the preparation of a-Al2O3 from secondary aluminum dross was studied. Factors including alkali dross ratio, salt dross ratio, smelting temperature, smelting time, leaching temperature, leaching time, and the solid-liquid ratio, which possibly influence the transfer of Al into water were studied, and the feasibility of using seed precipitation as a treatment technology of the leachate was discussed. The optimum condition of the process was determined as: alkali dross ratio 1.3, salt dross ratio 0.7, smelting temperature 500°C, smelting time 60min, leaching temperature 60°C, leaching time 30min, solid-liquid ratio 1:4. The results show that using the seed precipitation method, the leaching of aluminum reaches 92.71%, demonstrating the technique as a feasible and effective treatment technology of the leachate.

Jan 1, 2011

By John C. Luck Jr.

"DEVELOPMENT of oil emulsion mud dates back to the early days of rotary drilling when oil was added to the drilling mud solely for the purpose of freeing stuck drill pipe. After the drill pipe was freed, and drilling resumed, this oil was considered a contaminant. Efforts were made to remove the oil but some of it remained and was emulsified with the drilling mud, thus forming a mechanical emulsion.During the late 1930's, operators found that adding crude oil to drilling muds seemed to alleviate 'sticky-hole' problems and so oil was allowed to remain in the mud. This practice was adopted when it was found that faster drilling rates and longer bit life were obtained. These observations led to the development of emulsion drilling muds. During the past five years their application has become more widespread because of the lower fluid losses obtained, greater lubrication qualities, faster penetration rates, and generally better hole conditions.An emulsion may be defined as a two-phase system consisting of a mixture of either finely divided oil droplets in water or of finely divided water droplets in oil. The surrounding liquid is known as the continuous phase. The emulsifiers reduce the interfacial tension, making the droplets tend to repel each other so that they remain dispersed and stabilized. These emulsions are classified as oil-in-water or as water-in-oil, depending upon whether water or oil, respectively, is the continuous phase. Briefly, close inspection shows that they consist essentially of globules of• the one liquid suspended in a continuous mass of the other liquid. Oil emulsion muds are usually of the oil-in-water type. Two basic types of emulsifiers •commonly used in Canadian muds are soaps and lignites."

Jan 1, 1954

By P. Rosario

"Current industry practice for HPGR assessment and sizing relies on conducting a series of tests using pilot-scale machines with roll diameters of 700 mm to 1000 mm. Substantial amounts of sample are required for such pilot test programs, typically 1 to 10 tonnes of the sample is needed depending on the level of study and complexity of the resource. Collection of large quantities of representative samples during the early stage development is challenging and expensive, thus significantly hinders the HPGR technology from being incorporated into early-stage designs. A robust and reliable laboratory test is therefore needed to allow a fair consideration of HPGR for early stage projects. With support from the Canadian Mineral Industry Research Organization (CAMIRO), the NBK Institute of Mining Engineering at the University of British Columbia (UBC) developed a suite of Piston Press bench-scale tests that correlated to pilot and full scale HPGR operating information (Davaanyam, 2015; Davaanyam et al, 2015; McClintock, 2018). The Piston Press Tests (PPTs) are capable of assessing the HPGR technology at the scoping, pre-economic analysis (PEA), and pre-feasibility (PFS) stages of project development. This paper will briefly describe the theory on which the PPTs are based, and then presents a case study conducted for a copper deposit to show how the PPTs are being used for scoping and pre-feasibility level studies. Specifically, the PPTs are being used to provide information for preliminary sizing and selection of an HPGR and to assess the effect of ore variability on HPGR performance. The results are also applied to developing HPGR circuit designs and can be incorporated in simulation so that optimum design parameters can be selected.INTRODUCTION It is widely accepted that high pressure grinding rolls (HPGRs) offer a viable energy-efficient solution for the modern comminution flowsheet design. Table 1 summarizes selected examples of HPGR applications in the hard rock mining industry. The main benefits of HPGRs are energy savings which leads to lower operating costs, and its stable operating characteristics that can better cope with variations in ore hardness when compared to the conventional SAG mill-based comminution circuits."

Jan 1, 2019

By W. C. Ferguson

"This paper could be more appropriately titled ""The Application of Vacuum Filters to Underground Minewater Treatment. in a previous paper co-authored by the writer (1) the history and development of minewater treatment at the Sudbury District Operations of the International Nickel Company was outlined. It is the intention of this paper to dwell more specifically WIth the the application of the vacuum filter to a problem found in most, if not all, underground mining operations. In the preparation of this paper the writer has made liberal use of the illustrations and text of the paper previously noted.Last year we heard Mr. Nemeth discuss the basic mechanisms involved in vacuum filtration (2), and today Yr. Cunliff has exposed us to the selection of the filter media (3). I will now briefly review the various vacuum filter designs that generally lend themselves to metallurgical dewatering applications.DRUM FILTERSThe revolving drum-type which filters on its outside periphery is illustrated in Fig. 1. This is the Oliver or Drum filter and represents the first commercially available continuous vacuum filter. The original design dates back more than 50 years, but with the exception of the method of discharge, is identical to the units being marketed today. This filter is generally applied to slow filtering slurries. The cake may be discharged in several ways; strings, scraper blades, rolls or by passing the filter cloth over a small diameter discharge roller (belt discharge).THE DORRCO FILTERThe revolving drum type which filters on its inside periphery is illustrated in Fig. 2. Here the slurry lies in the drum and the cake discharges through a chute or conveyor. This type of filter is most often applied to fast-filtering slurries.THE DISC FILTERThe revolving filter which filters on the vertical plane of the disc is referred to as the Disc or American-type filter. This represents the most inexpensive design in terms of cost per square foot of filter area. This filter is widely applied, but is probably more suitable for slower draining pulps."

Jan 1, 1971

By Cheryl L. Allen

The increasing energy costs associated with mining has become an issue that needs to be addressed for future sustainable production. Vale Inco is undertaking a Ventilation on Demand (VOD) Project in an effort to minimize costs, continue to mine at depth and reduce green house gas emissions. A dynamic VOD system is very complex with potential high risk. Therefore, a systematic approach is being taken for successful development and implementation of the concept. The physical components of the system are currently being tested at various Vale Inco mine sites. While the operability of the physical components are being tested, the strategy for optimizing the architectures of the system is being defined. This presentation discusses the method of developing a VOD system at Vale Inco.

Feb 1, 2008

By N. Bédard

"This paper highlights Cambior’s initial approach for recruiting and retaining its international employees, the importance of proper preparation and the support needed to ensure a competent and stable workforce.In general, most of the training and information available for human resources personnel prepares the specialist for handling various aspects of labour relations, recruitment and hiring, benefits administration, employee relocation, etc. This is usually done in a Canadian context.Only recently, has more specialized training been developed to prepare human resources practitioners for the complex issues related to expatriate employees and dealing with human resources issues in other countries"

Jan 1, 2004

By W. J. Tough

THIS paper offers examples of some of the typical calculations which occur in the ventilation of metal mines. The fi.rst section of the paper discusses the problems associated with natural-draft pressure; the second section presents the more common of the calculations concerned with the operation of mine fans; the third section illustrates the integration of the individual problems covered by the preceding sections into the larger problem of determining the operating characteristics of a fan for a particular mine duty. There is a very definite limit to the extent to which pure arithmetic can be successfully applied to the solution of min<; ventilation problems. As mines advance from the exploration, development, and initial production stage to the rime when underground workings become exceedingly complex, there is a considerable increase in the relative importance o theory and judgment in the solution of ventilation problems. These calculations illustrate the application of mathematics to ventilation, but they also in-elude examples of instances where arithmetic cannot be conveniently applied, and important estimates, based on judgment compounded of experience and a knowledge of the theoretical consideration involved, must be made. The inclusion of such estimates is intended as a guide and a warning to the reader; a guide in assisting him to recognize and estimate his own incalculables; and a warning that the solutions must not be blindly applied to his apparently similar problems. These sample calculations are intended to assist the reader in applying the theory contained in the standard texts on metal-mine ventilation. They have been selected from the ventilation experience of a British Columbia mine.

Jan 1, 1942

By C. Gerow

THIS paper is entitled "Some" problems, rather than "The" problems, met in selling coal, since the problems to be met in selling any commodity have to deal with an infinite number of circumstances and conditions. These are believed to be more varied in the case of coal than probably any other commodity. This is due, perhaps, to the fact that coal has been one of the basic materials in the guiding of industrial and national achievement for the past two hundred years. During this time its use has developed from a most haphazard one to uses involving all modern scientific methods, which, rather than simplifying matters as regards the marketing of coal, have added many fresh problems, and these vary according to the particular market served. Since the concern of this paper is primarily the selling of Nova Scotia coal, it is proposed to deal chiefly with some of the specific conditions met in the markets presently served by this coal. For the purpose of discussion, these markets may be considered as divided into three main groups, namely, the Maritime market, the Quebec market, and the Ontario market. THE MARITIME MARKET First of all, let us consider the Maritime market. This is a market which has been regularly served by Nova Scotia coal since coal mining became the first industry in Cape Breton, slightly over one hundred years ago. Conditions as applying to the use of coal have naturally tended to adjust themselves to the characteristics of the coal most readily available, and, therefore, marketing problems are fewer in the Maritimes than in districts where many coals of varied characteristics are offered. Up to recent years, the problems involved were chiefly those of providing satisfactory service insofar as de-liveries were concerned. However, with the speeding-up of manufacturing processes and the necessity of reducing costs to a minimum, users of coal have become interested in obtaining coal that will give the most economical service. It is, therefore, now of importance that the salesman should have full knowledge of the particular conditions applicable to each customer&apos;s use in order to deal to the best advantage.

Jan 1, 1936

By J. D. Campbell

"Coal is one of Alberta's major fuel resources, but its distribution, especially in the flat plains region, has been somewhat obscured by surficial deposits. After a period of neglect, easily strippable plains coal is presently approaching a position of dominance in electrical power production, a position it is likely to retain for a number of decades in the face of strong competition from hydro and nuclear power. Accordingly, the Research Council of Alberta has undertaken an inventory survey of the province's supplies of this resource.In the southern part of the province and in the north-central forest-fringe area, some strippable coal is found in the Belly River Formation and its equivalents, but major strippable coal reserves in large areas of central Alberta occur within the Edmonton Formation. The survey is planned on a reconnaissance scale, drilling test holes at 2-mile intervals in selected large areas. It appears to show that, in well-settled regions, large reserves of strippable coal are only to be expected where they have long been known; major presently unknown bodies of coal must be sought in unsettled regions or at depths too great for strip mining. However, such bodies might still be economically competitive with hydro and nuclear power in the production of electric power for some time to come."

Jan 1, 1967

By L. Kilpinen, K. R. Kay, H. B. Fowler

"FOREWORDThe International Nickel Company of Canada has built four ore concentrating plants since 1950. The fifth and largest is now under construction. In each successive plant, the level and type of instrument control and sophistication of control techniques have increased as experience was gained. The type of control progress is illustrated in Fig. 1.At Frood-Stobie the high degree of instrumentation and the level of control were made possible by the constant evolution of techniques and improved instrument hardware technology. We have established in practice concepts that are sound, although many modifications to instrument sensor types and locations 1-rere often necessary. It is generally true that at other existing Inco mills, it is possible to run ""all manual"" for protracted lengths of time because of operator availability and dependence. The Frood-Stobie Mill is the exception, and it is the degree of reliability of the instrumentation hardware and level of maintenance that has made this possible."

Jan 1, 1971

By G. R. C. Pacheco, D. M. Fonseca, R. Neuböck, G. E. Gonçalves, W. Moulin-Silva

Degradation by sulfur gases is an important lining wear mechanism in the copper industry. SO2/SO3 gases infiltrate into the pores of the basic refractory bricks, combine with their raw materials through expansive reactions and significantly modify the bricks’ structure. This study presents a comparison of the corrosion resistance against sulfur attack of different magnesia-based refractories using a simple, low-cost and quantitative method. Recipes containing sintered MgO grains showed lower resistance to corrosion by sulfur oxides compared to basic grades containing fused grains. Chromium corundum grades were used as a reference and showed very good resistance to this corrosion mechanism under the test conditions. The novel test provided relevant results that agree with what is commonly observed during operation and in previous post-mortem studies. This tool could be very useful in selecting refractory grades for the copper industry and predicting their performance. INTRODUCTION Oxidation of matte sulfides during copper production leads to the formation of sulfur oxides, which infiltrate into the pores of the refractory lining and react with the basic oxides below 1000°C to form magnesium and calcium sulfates. This reaction is accompanied by an expressive volume increase, consequent densification of the refractory microstructure and weakening of the brick bond (Malfliet et al., 2013). Thus, corrosion by SO2/SO3 is an important wear mechanism in the non-ferrous industry and the resistance to this compound should be considered when defining refractories for this application. Previous studies on this matter include expensive and complex testing methods involving pressurized SO2 gas cylinders in order to investigate the corrosion resistance of MgO-containing materials by sulfur oxides (Gerle & Podwórny et al., 2016; Fotoyi & Eric, 2011; Fotoyi, 2009; Podwórny & Piotrowski et al., 2008). The current study was based on a test developed by Pacheco & Fonseca (2018) to assess alkali infiltration and aims to provide an evaluation method of the corrosion resistance of refractories by SO2/SO3 in a simple and quantitative manner. This novel test is useful to compare the corrosion resistance of different refractory recipes and properly select the grades that should be employed in the non-ferrous industry. A case study is provided to illustrate the damage caused by sulfur oxides in refractory linings.

Jan 1, 2019

By Eric Best

"In the past two to three years, all continuous mining machines at the Potash Corporation of Saskatchewan Mining Limited, Lanigan Division, have been changed over to a new cutting pattern using 1 -inch- and 1-3/l6-inch-diameter self-sharpening pencil bits. The bits are arranged in a cone-type pattern across the face on 2 1/2 -inch and 3-inch spacing. The result is that the ore is removed by chipping and flaking. Previously, rap-lock bits were used, with the pattern being several bits in single rows at wide spacings. The cutting action was grinding and breaking.Besides improved penetration rates and lower bit costs, there are many other advantages. The ore size is much smaller, resulting in less wear and tear on conveyors and other associated equipment. Feeder-breakers are no longer routinely set up at the head end of every extensible belt, as the banana-shaped chunks of ore that used to require breaking are no longer produced. Also, less dust is generated by the cutting heads and fewer stops are required for bit changes. Even the mill operation has been improved, as fewer fines are produced.Further improvements are still sought after, but, all in all, the new cutting pattern is considered to be a giant step forward from the old method."

Jan 1, 1981

By A. Lawson

"Continued and expanded use of underground diesel-powered equipment is considered desirable in order to achieve necessary production capability, particularly when coal becomes increasingly in demand as an energy source. Although diesel engines are derated for underground use, concern has been expressed in many quarters regarding the health effects of worker exposure to diesel-generated particulate and NOx emissions. This concern will increase as Canadian diesel fuel quality becomes heavier and with higher sulphur content. This could result in a requirement to increase ventilation rates by 50%.This paper describes the results of studies of various approaches designed to reduce diesel emissions. Two major approaches have been followed: fuel modification, and emission control hardware development. The results of progress in the development of these approaches will be described.Fuel modification includes the application of water/diesel and methanol/diesel fuel emulsions to the engine. Details of the techniques employed in this approach will be described, together with the effects on diesel emissions. (The paper is concerned with the emission aspects only, not the possible major engine modifications and/ or substitute materials of construction for 100070 methanol.) Use of methanol has the added advantage of acting as a diesel fuel substitute and extender, and there are expectations that underground diesel engines could eventually operate on close to 100% methanol fuel, thereby eliminating particulate emissions. The results of emission control hardware development will also be presented and will include the effects of catalysts, water scrubbers, exhaust filters and exhaust gas recirculation techniques on emissions. A combined systems approach employing a number of these components appears to be the most viable method of controlling the complete array of diesel emissions.This work should culminate in a better understanding of the costs involved in employing fuel modification or emission control hardware relative to the costs of increased ventilation which mpy be necessary to maintain a safe working environment for the underground worker."

Jan 1, 1981

By S. M. Grillo, M. Fiori, R. Bornioli, C. Marini, S. Fadda

The Na-feldspar orebodies in Sardinia occur along structures belonging to a regional ENE-WSW system that developed during the late stages of the Hercynian orogeny, and that was reactived during the Alpine orogeny. The main petrographic facies include granitoids, albitized granitoids, albitites (more or less rich in quartz), and albitites containing Mg minerals. Field observations and petrological and geochemical data point toward a metasomatic origin for the albitite orebodies. Albitization involved depletion of K from K-feldspar and biotite, dissolution of free quartz, and a lowering of Sr/Na2O and CaO/Na2O ratios in the protolith, under conditions of a positive thermal gradient. The absence of later K-metasomatism implies that, during a subsequent decline in temperature, the composition of the albitizing fuids was modified by an influx of meteoric or other waters. Copyright © 1996 Canadian Institute of Mining, Metallurgy and Petroleum.

Jan 1, 1997

By C. B. Ndimande, C. Ntsele, M. Lisso, L. Arlow

"In the processing of UG2 platinum ore, stirred milling technologies are dominating regrind applications that require grinding the particles to P80s’ in the region of 45 µm. For this application stirred mills are 30–40% more energy efficient and require a smaller foot print compared to traditional tumbling mills. In this work a study was carried out using a batch pin mill and three scales of Stirred Media Detritors. A laboratory scale pin mill, a pilot scale Stirred Media Detritor with an installed power of 18.5 KW and two industrial scale Stirred Media Detritors in continuous operation, with an installed power of 355 KW and 1,100 KW were used. The industrial scale SMDs were in the secondary grinding section of a mill floatmill float (MF2) UG2 processing plants. The tests were focused on assessing the effect of feed rate and percent solids on power consumption and product fineness at lab scale, floatation response of the SMD product at pilot scale and on an industrial scale, the effect of feed rate on energy consumption and product fineness. The measurements obtained were feed flow rates, mill power and from the samples cut, particle size distribution of both feed and product. Specific energy was observed to increase with increasing percent solids over the 30wt% to 80wt% studied. Floatation response tests of the pilot scale SMD products show improvement in grade. Specific energy and reduction rations are observed to decrease with an increase in feed rate.INTRODUCTIONThe purpose of comminution in most mineral processing applications is to liberate the valuable minerals from gangue so that they can be recovered in subsequent separation stages. Most precious and base metal plants treat low grade fine-grained ores which require a higher degree of size reduction to yield the necessary degree of liberation (Partyka & Yan, 2007). Many authors have shown that the relationship between product size and grinding energy consumption is exponential, the finer the product from the comminution device, the higher the energy consumption (Gao & Weller 1993; Napier-Munn, Morell, Morrison & Kojovic, 1996; Jankovic, Valery & La Rosa, 2003). The suggested reason for this kind of relationship is that smaller particles have fewer flaws and higher strength than larger particles. Particles with fewer flaws and higher strength require higher energy for breakage to occur. One of the challenges most plants face is that of efficient energy utilisation in the liberation of the mineral from these complex ores. Conventional tumbling mills are not energy efficient in fine and ultra-fine grinding applications because some of the energy is spent on moving the charge and does not go directly into breakage. Stirred mills have been found to be about 30% to 40% more efficient and require a smaller foot print compared to traditional tumbling mills for regrind applications that require product size with P80s’ in the sub 45 µm regions (Radziszewski & Allen, 2013). Stirred mills are able to produce fine product because they can achieve a high number of stress events per unit time and volume compared to tumbling mills (Kwade, 1999a). To minimise energy usage without compromising product quality, the mining industry has adopted stirred milling technologies for fine and ultra-fine grinding (Radziszewski & Allen 2014; Kwade, 1999b). The south Africa platinum group metal (PGM) industry alone had over 40 stirred media mills installed by 2011 (Rule, 2011). Of that 40, 13 were in the ultra-fine grinding (UFG) application and the rest in main stream inert grinding (MIG)."

Jan 1, 2016

By A. Hosseini

Full-scale rupture tests were conducted on 508 mm (20 in) diameter API X-60 5.7 mm wall thickness pipes containing either axial semi-elliptical cracks or simulated corrosion defects with equivalent depths ranging from 20 to 60 percent thickness. In the case of the cracks, the failure pressures were predicted with reasonable accuracy when considering a level 3 failure assessment diagram (FAD) procedure based on API 579, as compared to level 2 FAD, since the mechanical properties were known. In both cases, the accuracy improved for shallower cracks. Considering simulated corrosion defects, the RSTRENG approach provided more reliable results on predicting the collapse pressure. For a similar depth and profile, the cracked pipes failed at a lower pressure than those containing simulated corrosion defects of equivalent depth.

Jan 1, 2010

By S. C. Livanou, S. P. Tampouris, E. N. Zevgolis

In ferronickel (Fe-Ni) production from oxidized nickeliferous ores, mechanical losses of ferronickel in the slag are reduced by magnetic separation. Slag from the electric furnaces (E/Fs) contains 0.16% Ni. Its magnetic separation gave a pre-concentrate with 0.76% Ni, weighing approximately 6.5% of the feed. Nickel recovery was 29.7%. This pre-concentrate was then treated in a second (concentration) plant. Concentration treatment involves screening, crushing and magnetic separation. A pre-concentrate with 0.76% Ni gave a magnetic concentrate with 2.58% Ni and a non¬magnetic part with 0.35% Ni. Smelting of the non-magnetic part without the addition of a reduction agent in a laboratory electric arc furnace, gave a ferronickel alloy with approximately 20% Ni and a slag with 0.16% Ni.

Jan 1, 2005

By W. Evans, T. Steis

"Sulphide ores under certain circumstances will react with explosives to generate an autocatalytic chemical reaction. This reaction is exothermic and results in the production of large volumes of poisonous gases and creates an unsafe, unstable condition with the possibility of a low energy deflagration or even a detonation of the loaded hole. This paper outlines the conditions that need to exist for such a reaction to take place and the precautions necessary to minimize or eliminate the problem in areas of reactive ore. A special case study involving a northern Ontario mine will be detailed.IntroductionOne of North America&apos;s leading underground gold producer&apos;s processes over 6500 tonnes of ore per day from an orebody containing high concentrations of sulphides. After six years of problem free operation, the mine experienced two serious reactions in two months between the sulphides and AMEX II, the ammonium nitrate and fuel oil explosive it uses."

Jan 1, 1995

By Damien Gaboury

"Two practical methods for correlating two or more diamond-drill core intersections, using a stereographic projection software are presented. The first may be used to establish if two or more vein intersections are correlative, based on their core angles and diamond-drillhole attitudes. The second method allows prediction of main vein attitudes from numerous intersections, based on a spherical density contouring projection. The methods are suitable for: (1) correlating veins in complex orebodies; (2) ascertaining lateral continuity of ore for reserve estimations; (3) demonstrating the hidden complexity of an orebody; and (4) correlating and interpreting various planar elements.IntroductionModern mineral exploration relies on diamond- drill core data and on the ability of geologists to interpret them. Drill core generally yields unoriented information, unless an expensive orientation device is used. As a consequence, strike and dip of planar elements such as lithological contacts or mineralized veins cannot be determined easily. This is particularly true for blind deposits (covered by thick overburden) and complex orebodies, where field data cannot support drilling interpretations. Such a problem has been addressed previously using two and three diamond drillholes and several solutions were proposed based on trigonometry, and geometric and stereographic projections (Mead, 1921; Wisser, 1932; Fischer, 1941; Stein, 1941; Bucher, 1943; Gilluly, 1944; Addie, 1962; Mills, 1963; Lyons, 1964). However, these solutions are time consuming and not relevant to present day computerized data plots."

Jan 1, 1997

By R. B. Taylor

"The Delnite mine is in the northwest part of Deloro township, Cochrane district. The property consists of 307 acres on the so-called 'South Break' in the Porcupine camp. The Company was formed in 1934 to take over the holdings of La Roche Mines, Limited. Gold has been produced continuously since June 1, 1937. The value of the gold recovered to date (December 31, 1946) has been $7,456,000, and the average grade of ore $6.81 a con.The ore at the Delnite occurs in relatively narrow, persistent, quartz-ankerite veins, which generally contain tourmaline and have a ladder-like structure. The gold occurs in the free state, and in association with pyrite and arsenopyrite, the two chief sulphides. The host rock is fine-grained, highly carbonatized andesite of Keewatin age."

Jan 1, 1954