Search Documents

By Veerendra Singh, Y. Rama Murthy, Sunil Kumar Tripathy, Nikkam Suresh

"High intensity dry magnetic separation is commonly employed to separate different para-magnetic minerals including mineral sand. Separation in these separators is majorly influenced by the combined effect of gravity, centrifugal and magnetic forces on a particle. These separators are included in the process flow-sheets either for pre-concentration purposes or for the beneficiation of paramagnetic minerals. Separation in these separators is majorly influenced by the difference in the magnetic susceptibility of the associated minerals, particle size and shape along with the process variables of the machine. Particle size is one of the major parameter that plays an important role and decides its probability of selectivity under the magnetic field. However, effect of particle size on the performance of these separators are not well understood which is evident from the literature.In the present investigation, an effort is made to bring out the effect of particle size on particle separation in an induced roll magnetic separator while treating ilmenite fines. Effects of operating parameters, such as; magnetic field intensity, roll speed, feed rate and splitter position have been studied and their influence on particle size has been analysed in terms of yield (wt.%) to magnetic product, particle size distribution characteristics in terms of D50 and D80 size, skewness, kurtosis. Also, the particle size distribution of each test was fitted in Rosin-Rammler equation. The test results were analysed statistically to understand and quantify the influence of each variable on particle separation. It is found that, rotor speed of the separator had maximum influence on yield to the magnetic product whereas splitter position had major influence on D50 and D80 (µm) size of the product."

Jan 1, 2016

By N. Parnian

"Carryover of caustic soda (NaOH) in the steam path caused catastrophic failure of superheater 304H stainless steel tubes in a steam generator and led to an unexpected shutdown after just five months of continuous service of petrochemical following the start of production. The cause of the failure was studied, with a focus on the formation of sigma phase in the weld joint and effect of caustic embrittlement on stress corrosion cracking (SCC). The cracks were examined at the seam weld, heat affected zone (HAZ), and Ubend areas. Hardness was measured for the base metal, HAZ, and weld metal, and microstructures were examined using optical microscopy and scanning electron microscopy (SEM). Crack initiation is attributed to gouging on the precipitated carbide at the HAZ and also the formation of sigma phase in the weld metal, as shown by energy dispersive X-ray (EDX) analysis. In addition, cracking was propagated by caustic embrittlement because of residual stresses and hammering. Finally, the characteristic feature of fracture was illustrated by SEM fractography, and consists mostly of intergranular SCC and some quasicleavage transgranular. INTRODUCTIONThree key factors are needed for the initiation and propagation of intergranular stress corrosion cracking (IGSCC): a susceptible material, a corrosive environment, and sufficient stress. Although austenitic stainless steels are susceptible to sensitization and IGSCC, they are widely used in boiler and superheater tubes because of their high corrosion resistance, high oxidation resistance, acceptable mechanical characteristics at elevated temperatures, and low cost.Sodium hydroxide is injected to neutralize acidic constituents in the steam path, but caustic can concentrate in boiler tubes and attack the surface metal (known as gouging) even traces of caustic in the steam can deposit on surfaces and cause local concentrations of several percent (ASM handbook, 1992). Not only sensitized grains but also sigma phase formed in the weld metal can initiate caustic cracking. In this research, the cause of the failure of 304H stainless steel superheater tubes in a methanol petrochemical plant in Iran was studied with a focus on the effects of caustic embrittlement on IGSCC."

Jan 1, 2012

By E. W. Mountjoy

THE Exshaw formation is a thin but very persistent black shale unit generally well exposed along the easterly scarp faces of the fault blocks comprising tl1e front ranges of the Rocky mountains. It is over lain by the Mississippian Banff shales and silty shales and underlain by the massive Palliser Limestone formation of late Devonian age. The Exshaw continues eastward under the plains of Alberta and on into Saskatchewan, with little change until it reaches the surface of the Palaeozoic-Mesozoic unconformity. During the summer of 1953, the writer was working- with a field party under Dr. J. L. Usher in the front ranges of the Alberta Rocky mountains. This party, sent out by the Mobiloil Company, conducted a geological survey of Devonian rocks between the towns of Banff and Jasper. The writer helped to describe and map these Devonian rocks and obtained first-hand information concerning the Exshaw shale and its relationship to the underlying and overlying sediments. Additional information was obtained from reference material and from a number of geologists whom the writer has consulted. Grateful acknowledgment is offered to them, to the Mobiloil Company for releasing field information, and to F. W. Beales and W. P. Hancock who helped edit the original paper for publication. Information from areas north and smith of that studied and from bore holes on the prairies is referred to. Localities mentioned may be found in Figure 1.

Jan 1, 1956

By A. E. Wraith, R. Harris, J. Qiu, R. Parra

Small pilot scale experiments have shown that it is possible to almost fully eliminate the minor elements (ME), namely As, Sb, Bi and Pb contained in smelter dusts by vacuum calcination of mixtures of the dust with sulphidizing agents such as dirty copper concentrate or elemental sulphur at 900 °C and 80 +/- 30 Pa for 90 minutes. The products of this calcination are a residue comprising a purified mixture of copper containing compounds along with the gangue constituents and a high sulphur condensate comprising a mixture of the minor element compounds. In particular, the Cu:ME ratios of the concentrate and dust were increased from 250 and 50, from 28 and 12 and from 36 and 8 to roughly 3000, 3000 and 100 for the calcine, for Bi, As and Sb, respectively. It has also been calculated that (i) the copper content of the vacuum calcine may be recovered by feeding it into a Peirce-Smith converter during its slag blow, and (ii) the resulting recycling could increase the minor element treatment capacity of a smelter by 100 % while also reducing the blister As content by a factor of three. The experimental results are briefly discussed and a treated dust recycling option is examined. Example operating conditions are presented and available commercial technology for the vacuum calcination of the mixtures is reviewed.

Jan 1, 2007

By John Jiang, Brian R. Hart, Stamen S. Dimov, Aparup Chattopadhyay, Barun K. Gorain

"This paper presents a systematic approach to metallurgy diagnostics using an integrated gold deportment methodology developed for complex refractory gold and copper-gold ore bodies. Quantification of gold deportment for these ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies.INTRODUCTION Studies were initiated on various complex ore deposits and also on samples representing various process streams. These complex copper-gold single refractory, double and triple refractory gold ores are mainly composed of silicates and/or carbonates with moderate amounts of clay and mica, along with minor amounts of sulphides and organic carbonaceous matter. Variable proportions of visible gold and “invisible gold” (sub-microscopic gold) were noted in different mineral phases for various ore types and process stream samples. Invisible gold commonly occurs as solid solution or as colloidal-sized particles in different sulphides and other phases for different refractory ores. The dominance of invisible gold and presence of highly preg-robbing along with finely disseminated carbonaceous matters adversely affects gold recovery in flotation and leach circuits for most of these double and triple refractory ores. This paper discusses applications of an integrated gold deportment technique developed for different types of gold and copper-gold ores, namely, complex copper-gold, double and triple refractory gold ores (Chattopadhyay & Gorain, 2014; Chattopadhyay et al., 2016). Various process streams from flotation and gold leaching circuits were investigated. Different concentrates and tailings samples from flotation circuits whereas feed and discharges from pressure oxidation (POX) and carbon-in-leach (CIL) residues were used from gold processing circuits."

Jan 1, 2017

By D. T. White

Pressure acid leaching of nickel laterite ores typically involves the production of an intermediate product that is releached and refined to pure nickel and cobalt products. BHP Billiton is developing the Ravensthorpe Nickel Project to produce up to 50,000 t/y of nickel via a mixed hydroxide intermediate, which will be refined at its Queensland Nickel (QNI) Yabulu Refinery near Townsville, Queensland. The hydroxide precipitation flowsheet has been adapted to process high magnesium ores through an atmospheric leach stage, eliminate iron(III) as jarosite and oxidise iron(II) during neutralisation. The neutralisation conditions are controlled to precipitate aluminium, chromium and silicon, and to ensure good solid-liquid separation. Soluble impurities such as magnesium are purged with the tailings stream and will be managed over the long term by crystallisation in evaporation ponds.

Jan 1, 2006

By Richard E. Barrett

SOME YEARS AGO I was associated with a mining operation which, because of its isolated location, burned wood for heating purposes. Year after year the tractors and tucks hauled the cordwood in from the edge of the ever-growing clearing. Each year the cartage costs became greater. The degree to which transportation distances affect the economics of fuels obviously varies with many factors, but the main criterion is the amount of heat a unit weight of the fuel will produce. For in-stance, wood is limited in most cases to a haulage distance of a few miles. Coal can be shipped hundreds of miles, whereas petroleum and gas ?can be transported thousands of miles. The world is now on the brink of having a new fuel -uranium. It has the virtue of being so concentrated that transportation costs can, for all practical purposes, be disregarded.

Jan 1, 1958

By M. J. Collins, B. Parekh, A. Hasenbank, B. Hewitt

Newcrest Mining Limited, originally as Lihir Gold, has operated a pressure oxidation plant for the recovery of gold from refractory ore since 1997. The mine and gold plant are located on Lihir Island in Papua New Guinea. Design of the original pressure oxidation circuit was based on the results of pilot plant tests conducted by Sherritt in Fort Saskatchewan. Following a decision to expand the plant in 2008, Lihir Gold contracted Sherritt to design a new autoclave. The design exercise utilized the original pilot plant test results, commercial process results at Lihir, and an understanding of advances in autoclave technology since the original plant was built. The new Lihir autoclave will be the largest horizontal, multiple-compartment autoclave in the world. The design process for the pressure oxidation expansion is described in this paper.

Jan 1, 2011

"Decreasing gold-in-ore grades is one of the main drivers of poorer productivity and rapidly escalating unit costs. Grinding costs, water use and reagent consumption are all intimately related to the ore grade processed. Various pre-concentration technologies have been developed that can be applied at various stages of crushing prior to ore grinding. This paper will review the amenability of ores to coarse particle barren gangue rejection for fine crush sizes in the pumpable particle size range (i.e., particles between 5 mm and 0.3 mm in size). The liberation of oxide gangue achieved during crushing is evaluated by proxy using sink-float analysis and the deportments of gold, sulfur, and arsenic into sinks and floats are monitored. Amenability of gangue rejection by continuous gravity separation is evaluated after various crushing modes (vertical shaft impact crushing, cone crushing, and HPGR crushing). The potential to identify coarse particle mineral association and liberation using three-dimensional x-ray computed tomography will be discussed.INTRODUCTIONThe aim of research in this area is to explore some of the attributes which make some ores amenable to preconcentration, or rejection of a significant component of the feed mass to tailings at a coarse liberation size. Characteristics such as ore type, mineralogy, breakage pattern, particle shape, and liberation characteristics may need to be examined to identify amenability to pre-concentration amenability.It is intended to focus on continuous gangue rejection in the pumpable size range (0.3–5.0 mm) as this remains one of the key opportunities to reduce processing costs through a combination of techniques including screening (for mineral differentiation rather than size classification only) and gravity separation (using jigs). This is to be contrasted to conventional preconcentration as performed with automatic ore sorters."

Jan 1, 2016

By W. R. Cowan

The availability of mineral aggregates for construction purposes is rapidly declining through inadequate resource planning. restrictive zoning and legislation , and competing land uses. The Geological Branch of the Ontario Ministry of Natural Resources has undertaken to provide aggregate inventory reports for all townships designated under The Pits and Quarries Control Act, 1971, and eventually for all towns hips in heavily populated areas. The reports contain maps and recommendations for extractive zoning by municipalities; of necessity only the largest deposits are given priority recommendations. It is intended that these reports should improve the resource planning in areas underlain by large aggregate deposits. The inventory is only possible because a concentrated effort has been made to map the Quaternary geology of populated areas over the last ten years. Future needs require that we develop methods to determine the extent of poorly defined and buried aggregates and that we look for natural alternatives.

Jan 1, 1978

By Robert F. Shurtz

This paper discusses and compares methods of statistical analysis of the information relating to the evaluation of an asbestos deposit. From a study of 10-ft. lengths of drill core, the separate effects of visual evaluation errors were determined, as well as the deviations between evaluators and the deviations produced by a slight displacement in the center lines of the check drill holes. The importance of careful statistical analysis of such information is stressed.

Jan 1, 1966

By R. Scheepers

"Abstract -Mineral deposits and prospects of the Pan African Saldanian orogenic belt in the south­ western Cape Province South Africa, are reviewed. Despite the entire absence of operating base or precious metal mines in the area, this study has established at !east four metal associations that offer enticing exploration potential .The poly-phase deformed, low-grade metamorphosed volcano-sedimentary Malmesbury Group constitutes a complex, poorly understood supracrustal sequence that has been loosely subdivided into the Tygerberg, Swartland and Boland tectono-stratigraphic terranes by northwesterly trending fault zones. Syn- and post-tectonic granitoids of the Cape Granite Suite selectively intruded these terranes. Early S-types preferred the Tygerberg terrane whereas the later I-types dominate the remaining areas. Anorogenic A-type granites, however, occur in all three domains. Known metallization is directly or indirectly related to the intrusives, yet syngenetic deposits are conspicuously absent from the supracrustals. Four metal associations have been identified.•,Cassiterite-wolfrarnite (± Au, Cu, Mo, Fe-sultides) in quartz and quartz/aplite veins hosted by tourmalinized and locally greissenized S-type granite. Similar exo-granitic veins occur in proximal metamorphites.•,Juxtaposed disseminated, stockwork, breccia and vein style Cu-Mo-Fe-(Au)-sultide mineralization hosted by matie to intermediate intrusives of high K calc-alkaline, 1-type affinity.•,Cu-Mo-Au-sultides hosted by hydraulic breccia pipes, stocks and veins occurring in anorogenic A-type alkali feldspar granites and amphibole quartz syenites.•,Scheelite with minor Cu-Mo-sulfides and Au-associated with endo- and exo-skarns spatially related to I-type monzogranite, granite and alkali feldspar granite .The first three associations occur along the Yzerfontein-Helderberg-Zone, a 180 km lineament in the Tygerberg terrane, a zone exploited by syn-, late- and post-tectonic intrusives and their related mineralization. The fourth association is typical of the Boland terrane. The spatial and temporal relationships between the various metal associations is interpreted as the result of sequential intrusion of relative early high level S-type, followed by intermediate level I-type and finally anorogenic A-type granitoids during the evolution of a contracting continental margin arc and its inner arc. This plate tectonic setting suggests subduction in an easterly direction underneath the Kalahari craton. The spatial configuration of the various terranes at the present erosional levels is the result of rifting and significant differential vertical displacement following cessation of subduction, a terminal tectonic event possibly synchronous with intrusion of the A-type granitoids.Near surface preserved roof zones and cupolas of both S- and I-type granitoids in the Tygerberg and Boland terranes, respectively, render these areas extremely prospective for Sn, W, Mo and Au mineralization. The presence of intermediate to mafic volcanics, a diversity of calcareous lithotypes and favorable plate tectonic setting of the Malmesbury Group suggest potential for the thus far elusive VMS, MVT and Sedex base metal and minor precious metal deposits."

Jan 1, 1994

By H. Bouzahzah

The field of quantitative mineralogy has evolved significantly through the development of image analysis techniques and information technology. Quantitative mineralogical characterization can now be routinely conducted for determining ore compositions and understanding the behaviour of minerals within mineral separation processes. The characterization of mine tailings is another important application of quantitative mineralogy. The estimation of acid and neutralization potential as well as the interpretation of kinetic leaching test results are often based on quantitative mineralogical knowledge (mineral abundance, texture, metal distribution amongst minerals, etc.). The objective of this paper is to determine and compare the accuracy of four mineralogical characterization techniques that are often used for environmental sample analysis: (1) X-ray diffraction, (2) normal analysis from chemistry analyses, (3) normal analysis from specific gravity measurements and (4) SEM-EDS image analysis. For this purpose, three artificial samples were assembled by mixing pure minerals in proportions often observed in mineral processing plant tailings. BILMAT, a statistical data reconciliation software, was applied to reconcile the chemical analyses with the results of other mineralogical analysis techniques and to estimate the acid and neutralization potential of actual mine tailings samples. The acid mine drainage was qualified from the acid potential and neutralization potential equilibrium as determined through quantitative mineralogical analysis. The statistically reconciled data made it possible to predict the metal deportment as a function of their bearing minerals and therefore, in the case of neutral contaminated drainage, to assess metal leaching potential.

Jan 1, 2016

By Y. Gordon

ABSTRACT A methodology based on a two-stage approach was developed for process technology selection. The first stage includes evaluation of available technologies, followed by shortlisting the best technologies based on mass and energy balance modelling, financial analysis, and risk analysis. The second stage involves detailed analysis using refined input data, mass and energy balance modelling, and capital and operating cost estimation, as well as a more detailed financial analysis. A case study covering the selection of ironmaking technologies for a company in the Russian Federation is presented to illustrate the critical elements of the methodology and the analysis process.

Jan 1, 2014

By Xing-Liang Sun, Xian-Min Han, Zheng-Guo Zhu

The study on the material properties of frozen soils in China was being developed quickly in the past decades of years, because of the increase of the engineering constructed in frozen soil regions on the Qinghai–Tibet Plateau, and numerous research results were achieved mainly about strength and deformation behaviour and constitutive models of frozen soils. Studies have shown that the deformation procedure of frozen soils is irreversible; therefore, it is more appropriate to research mechanical properties of frozen soils by means of damage mechanics theory. In this paper, an elasto-viscoplastic anisotropic damage model is presented by introduction of Perzyna viscoplastic equation into analyzing the deformation of frozen soil. In addition, an anisotropic damage evolution equation is obtained by means of extending non-viscous damage to viscous damage. Triaxial tests at different strain rates are chosen to illustrate the application of this model, and good agreement between experimental data and numerically simulated results is obtained. The calculated results indicate that, under the same conditions, the damage at higher strain rate is less than that at low one. So the phenomena are explained from damage mechanics that the frozen soil has larger elastic modulus and shear strength at higher strain rates, and explained from mechanism that the emergence and development of micro-cracks in the body of frozen soil can be to some extent retarded at higher strain rates.

Jan 1, 2015

By Y. M. Shneerson, V. M/ Shpaer, E. E. Zhmarin, A. Y. Lapin, E. M. Vigdorchik

This paper describes studies of zinc concentrate oxidizing pressure leaching using the method of mathematical modeling. The concept of a kinetic function was taken as a basis for mathematical modeling of the leaching process. The kinetic function describes dependence of the unreacted component share OJ on the relative time x (the relative time is the ratio of the test duration and the time of complete dissolution). This kinetic function is determined in accordance with the results of batch laboratory tests. The laboratory tests have been carried out on zinc concentrate produced from Kazakhstan zinc-copper ores. Zinc concentrate consisted mainly of three types of minerals: sphalerite (70%), pyrite (13%) and chalcopyrite (10%). Oxidation reactions of sphalerite, pyrite and chalcopyrite have been considered as principal ones. The kinetic characteristics of the process (kinetic function, reaction order, activation energy, duration of complete dissolution of the concentrate components) have been calculated in the course of laboratory tests. The mathematical model was used for estimation of the main technological leaching process parameters (such as process rate, degree of metals extraction, autoclave capacity, heat balance, etc.). Mathematical modeling based on the kinetic function concept allows safe designing of metallurgical equipment and scaling the technology to industrial capacity.

Jan 1, 2004

By Fred Horne

1N THIS PAPER, the writer proposes to limit his comments to few generalized phases of the subject, based on his personal experience in the midwestern United 'States and in one section .of the Coal Branch in Western Alberta. The following statistics are submitted to show the importance that strip mining has assumed in the coal mining industry of the United States. In 1914, 1,281,000 tons of strip coal were produced, amounting to 0.3 per cent of the total production. In 1948, the total was 13~,505,000 tons, representing 23.3 per cent. In 1949, the percentage figure dropped slightly and this can be partially accounted for by the labour disturbances prevalent throughout the year. In 1914, there were 48 power shovels and draglines being used in the stripping of coal; in 1949 there were 3,712, not to mention other types of coal stripping equipment such as bulldozers, tractors and scrapers, rotary excavators, and stackers. At the bituminous coal mines in Western Canada, strip mining was introduced only a few years ago, two of the major reasons for its development being the need for increased production during the war and post-war years and the need to hold the line on increasing production costs, but even in these few years the percentage of strip production has in-creased to such an extent that some mines that, five or six years ago, were producing all their tonnage from underground operations are today obtaining up to 80 per cent of their total output from strip mines.

Jan 1, 1951

By C R. Crook

A brief outline of production methods and processes is given to show how maintenance fits into the picture at this plant. The work force, and the tools needed to carry out this function, are then described. Preventive maintenance practices, scheduled annual shutdowns and routine check-downs are explained, especially as related to planning and to the materials and labour involved for a mini-mum downtime. A brief explanation of the materials, sup-plies and spare parts program, as well as the part played by the Stores Department in conjunction with the Maintenance Department, is given. Cost control and equipment expenditure indicators are explained. Some specific examples of maintenance jobs are described in order to show the flexibility of the program. S HERRITT GORDON Mines Limited has been in continuous production, except for the planned downtimes needed for expansion tie-ins, or the annual shutdown check-over periods, since the first shipment of nickel on a commercial basis in July of 1954.

Jan 1, 1964

By G. H. Montgomery

THE PROPERTY of Aunor Gold Mines, Limited, consists of eleven claims, located in Deloro township, approximately three miles southeast of the town of Timmins. Production began in 1940 and currently the mine is operating at a rate of 485 tons per day. GEOLOGY AND MINE DEVELOPMENT The ore zone at Aunor occurs in altered lavas bounded on either side by soft talc-chlorite schist, locally known as 'soapstone'. The zone has a strike of N.80°E, dips 60° North, and varies in width from 0 to 250 feet. Within this zone the main orebody has a westerly plunge, away from the No. 1 shaft area (Figure 1). The mine is developed by a vertical three-compartment shaft from surface to the 3,082-foot horizon. Working levels are spaced at 125- foot intervals from the 625-foot to the 1,625-foot horizon, from which to tl1e 2,125-foot level the interval is 250 feet.

Jan 1, 1957

By A. M. Glendinning

"IntroductionLocationTHE PROPERTY of Aunor Gold Mines, Limited is in Deloro township, Ontario, about three miles southeast of the town of Timmins. It consists of a group of eleven claims located between those of Buffalo-Ankerite Gold Mines, Limited, and Delnite Gold Mines, Limited.GeologyThe ore zone at the Aunor mine consists of a narrow band of fine grained pillowed andesite, irregular bands of 'brown to green carbonated andesite, and lenticular bodies of quartz feldspar porphyry. The zone strikes N.80°E., dips 60 North, and has been traced for 5,000 feet across the property. It varies in width from 0 to 250 feet and is bounded on the north and south by masses of dark bluish-grey tale chlorite schist. These schist bands have widths up to 500 feet.The ore occurs in a series of parallel and branching veins confined to the limits of the zone. These veins tend to terminate and die out on the footwall schist contact, striking generally parallel with the ore zone. In wide sections of the zone, 150 to 250 feet, the veins range in width up •to 3.5 feet and may occur in two or three horizons across the width of the zone, each mineable independent of the other. They tend to dip a little flatter than the general dip of the zone. Where the zone is narrow, the veins are so closely spaced and numerous they can be mined together and in some places the complete zone has been mined from schist to schist."

Jan 1, 1953