Search Documents

By S. P. Jekielek

"This paper describes the automation of a mine hoist ore loading pocket using a programmable controller. It provides an introduction to programmable control, and outlines the various modes and operating sequences of the loading pocket. A comparison is made with previous equipment to illustrate the increased flexibility, reliability and diagnostic functions that are gained.IntroductionLoading pockets have evolved from a couple of manually operated air cylinders to entirely automated systems. Early pockets were usually formed in rock, with loading and discharging regulated by air-operated gate s. Interlocks, added to this arrangement, prevented simultaneous operation of the gates and ensured proper hoist position . As the loading pocket advanced, it was recognized that gravity feed posed problems, often becoming plugged or letting water run through into the shaft. A belt conveyor was employed, eliminating the se problems and resulting in greater loading control. Weighing the combination of transistorized logic modules, replaced many relay systems. This elimination of moving parts and contacts increased reliability and reduced maintenance costs.As semiconductor technology progressed, there were major breakthroughs in miniaturization and reliability, and as a result the programmable controller was introduced. Programmable controllers first appeared in the automotive industry in the late 1960's. A system controller was required to replace the large relay panels in operation at that time. The use of digital integrated circuitry enabled these programmable controllers to automate processes with hundreds of inputs and outputs. Advances in electronics reduced production costs , making controllers for smaller application s viable . This development is on-going, each generation introducing controllers with greater capabilities for a wider variety of systems. equipment was the next step in loading pocket development, and dependance on much of the manual control was reduced . The complete system was first automated using relay panels. Solid- state devices were later introduced, and static control,"

Jan 1, 1980

By Earl Gebhardt

The planning and design of mining panels in the Potash Corporation of Saskatchewan Inc., Lanigan Division mine Block B involved a number of investigative techniques. The techniques utilized to gain insight into the viability of mining included 2-D and 3-D seismic surveys, longhole drilling, exploration wells, photolineament, magnetic and gravity surveys, and actual room excavation.

Feb 1, 1993

By P. J. Lunder, R. C. Pakalnis

This paper presents the results of research that has been undertaken in order to develop an improved method of determining the strength of hard-rock mine pillars. Pillars are found in various shapes and sizes in all underground mining operations. Prudent engineering design requires that if pillars are to perform as desired, both the pillar strength and the pillar stress must be determined. A detailed pillar stability study has been combined with an extensive database of published pillar case histories (178)resulting in a new “hybrid” pillar strength formula, “The Confinement Formula”, that utilizes classic strength of rock methods combined with empirical methods. “The Confinement Formula” utilizes a “mine pillar friction term” calculated from the average minor/major stress ratio with-in the pillar core. Statistically, the new formula provides better results at predicting pillar strength for the combined database than the best empirically ft pillar methods that currently exist. “The Confinement Formula” allows for the determination of the strength of mine pillars with an increased level of confidence over previously applied methods.

Jan 1, 1997

By V. F. Hollister

Four conditions are commonly accepted as being needed for the development of native sulphur deposits in sedimentary rocks : (1) ample sulphate-bearing evaporite, normally anhydritic; (2) proximity to petroleum deposits; (3) a hydrodynamic system of communication between these two; (4) a stratigraphic or structural trap to prevent escape of the sulphur and sulphur -bearing reaction products. When any of these requisites are absent, apparently no significant residual bio-epigenetic sulphur deposit will form. These requirements are, however, satisfied in some areas, which include both the Triassic and Devonian evaporites of northeastern British Columbia.

Jan 1, 1977

By L. K. Nenonen

"Given the properties, locations and quantities of material to be hauled and the dump locations and capacities, the designer wishes to select the type and number of trucks and loading equipment required. Accordingly, software is being developed to assist in creation of the equipment, material and road network data bases, in selection of equipment, materials and road networks from these data bases, and in evaluation of the expected productivities both in a rapid, non-interactive, approximate fashion and a more detailed interactive fashion which permits the user to act as superintendent, if he so chooses. The basic technology has been developed and applied to an open-pit copper mine and is being refined and generalized for oil sands and coal mining applications.BackgroundA set of mathematical and interactive computer models are under development to aid in the selection of equipment and operating policies for an open-pit oil sands mine being planned by Canstar Oil Sands Ltd. This paper describes the computer models being developed of truck haulage systems. Although the interactive truck haulage model is based primarily on a model developed by the National Research Council in collaboration with Glenayre Electronics Ltd. of North Vancouver and Lornex Mines Limited(2).(3l, substantial changes and improvements are being incorporated to greatly increase its generality re equipment types, road network characteristics, dispatching and supervisory policies, etc. Although this paper is principally devoted to the truck haulage model, discussion is included concerning its interactions with other models."

Jan 1, 1982

"Developing markets for western metallurgical coal have continued to stimulate considerable exploration activity in the Rocky Mountain foothills and to influence major segments of a wide-ranging carbonization R&D pro-gram. Adjunct studies have included expanded petrographie investigations.Coal preparation has• been principally directed toward utilization of prepared small coal and was, like much of the year's combustion work, strongly influenced by concern over atmospheric pollution. Particular attention has been given to desulphurization and to the suppression of pollutants in combustion systems.In the area of non-fuel utilization of coal, interest has centered on plant nutrients and on a series of coal-based carbons which, inter alia, possess utility as filtration media.Other projects included the development of improved sampling and analytical methods, investigations into the effect of storage on coal proper-ties and R&D in solids pipelining. In addition, a significant volume of basic 'uncommitted' research has been maintained."

Jan 1, 1968

By O. Peters, D. Lascelles, R. Caldwell

Ageing tests on a crushed Cu-porphyry ore were conducted to assess the impact of sample oxidation on flotation performance. The objective of the testwork was to simulate ageing of ore that would be blasted through block caving but not milled for possibly several months. Ageing was performed in specially designed columns, using site and deionised water to keep the samples moist over the entire ageing period. Samples from each ageing interval (0, 0.5, 1, 2, 4, and 8 months) were examined for physical and metallurgical changes resulting from the ageing process through chemical analyses, size analyses, and batch flotation tests.

Jan 1, 2009

By A. C. A. Howe, J. C. Rowntree

"The Bernie Lake pegmatite near Lac Du Bonnet in southern Manitoba is a complexly zoned pegmatite containing several lithium-bearing units in addition to the western world's largest known reserve of cesium. The pegmatite forms a flat-lying ellipsoidal body within an east-west-trending Precambrian amphibolite. The pegmatite enclosed by this vertically schistose amphibolite lies near the eastern tip of a granitic intrusive. The relationship of this intrusive to the pegmatite is obscured by Bernie lake. To date, the pegmatite body has been delineated aver an area of approximately 80 acres; it attains a maximum thickness of 280 feet. Several distinct zones, including three assemblages of economic importance, comprise the pegmatite itself. The combined spodumene and lepidolite assemblages provide a recoverable defined lithium ore reserve of almost 5 million tons averaging more than 2 per cent lithium oxide. The recoverable cesium ore of the pollucite assemblage provides 300,000 tons averaging more than 20 per cent cesium oxide; this represents more than half of the western world's pollucite reserve. The Bernie Lake pegmatite deposit, owned by Chemalloy Minerals Limited, is well located with respect to the growing United States markets, and its reserves of cesium are large enough to enable it, under favourable economic circumstances, to become the major producer of this metal in North America."

Jan 1, 1967

By D. K. Fountain

"High metal prices and advanced technology in open-pit mining methods have resulted in considerable interest in the development of large, low-grade mineral deposits. Brenda Mines Limited is presently testing such a deposit of copper-molybdenum mineralization near Penticton, British Columbia.The mineralization of economic interest at Brenda has a total metallic sulphide content of between 1 and 1.5 per cent. This sulphide content approaches the limits of detectability of standard geophysical methods. How-ever, due to a favourable geological environment, it has been possible to utilize the Induced Polarization Method to outline the mineralization at the Brenda property."

Jan 1, 1968

By Egon Berger

"In recent years the trend in underground metal mining has been toward ever increasing blasts (often in excess of 100 000 tonnes per blast). The Canadian mining industry has been in the forefront of these developments (VRM, LBHand cable bolting to stabilize the surrounding rock /avoid dilution).In order to move these large tonnages, efficient loading systems have to be developed. This paper shows the technical and economic implications of various loading scenarios based on a predefined (however typical) stoping layout by:1 . discontinuous loading using scoop trams;2. discontinuous loading using scoop trams in combination with low profile dump trucks;3. continuous loading (based on loading performance/operating costs of the AL-60) in combination with low profile dumptrucks.The cost advantages of production concentration (loading large tonnages from one drawpoint}, made possible by continuous loading as opposed to sea tiered mining (small tonnages), using discontinuous loading in tunnelling will be presented, based on actual results obtained in a decline development project using the A L-60 continuous loader. At as pacing oj150m between turning bays, it was found that continuous loading was out performing discontinuous loading in approximately80% of the overall decline development.Fuel consumption and total cycle times are compared, and a cost assessment is presented.INTRODUCTIONThe subject of this paper deals with the introduction of continuous loading in underground metal mining and single heading tunnelingContinous mining has been widely introduced both in underground and surface coal mining. Mechanized longwall mining, utilizing moveable shield supports in combination with double drum- shearers, has resulted in a tremendous increase of coal production per working face.This has led to very concentrated mining operations. In a typical German coal mine two mechanized longwalls nowadays would produce the same amount of coal as 12 to 15 longwalls in the 1950s. One longwall in a South African coal mine has recently set a world record with 120 000 tonnes of coal in a single month.In underground metal mines-often due to the irregular nature of the ore body and the mining methods used-mining is far less concent rated. Ore is often produced from a large number of stopes and production sections. Sometimes, a substantial amount of ore may be obtained from development in the orebody (40070 at a German base metal mine)."

Jan 1, 1989

By Robert Strachanm

The East Kootenay coal-field, situated close to the boundary between the provinces of Alberta and British Columbia, is composed of four small areas locally called the Crow's Nest Pass, the Upper Elk, the Flathead and Crown Mountain, and comprises an area of about 3 78 square miles. From eleven to twenty-five seams have been exposed of two feet and over in thickness, with a total thickness of about 200 feet of coal, and reckoning about one hundred feet to be workable, gives an estimate of coal available of about thirty-seven billion tons. The coal is a high-grade bituminous, occasionally tending towards anthracite, and the majority of the seams furnish a. very good quality of coking coal as well as an excellent steam coal. The coal-field is found in the mountain ranges in long narrow strips. The age of the fonnation and the thickness of the covering beds have had considerable influence on the character of the coal, and lateral pressure and disturbances in the process of mountain-building have wrought great changes. With such an abundance of coal, it has been a disappointment that the East Kootenay field has not figured larger industrially. So far only one portion of the coal-field has been utilized. This is the Crow's Nest, where, in 1898, the Crow's Nest Pass Coal Company commenced development. Access to the coal seams was easily obtained, the mountain creeks having eroded away the covering, and mines were driven into the coal seams. In that year about ten thousand tons of coal were produced from the mine at Coal Creek.

Jan 1, 1924

By J. H. C. Scrimgeour, T. Toong, R. E. Hamilton

"The principles involved in the use and application of mathematical models as an aid to the development of advanced process control computer systems are described briefly. This is followed by a brief survey of known models of this kind for the simulation of mining industry processes.The main part of the paper describes a dynamic model of the flotation process developed by Canadian General Electric. Using flotation rate constants for each species of mineral and gangue, the model provides a numerical solution of the differential equations describing cell behaviour. The cell mode] is used repeatedly as a subroutine in the •over-all-plant model. The features of the cell and plant models are described.Simulation runs from the plant model show stream .assays and other indications of plant behaviour printed typically in 1-to 10-minute steps for several hours of •Operation following typical disturbances such as changes in feed rate or reagent addition rate. The simulation can :Show expected behaviour for both uncontrolled and computer-controlled plants."

Jan 1, 1970

By Y. F. Jiang, K. Fang, Q. Q. Jiang, Q. Wu

Inter formational sliding of bedding planes between two different rock types in Badong formation is an important reason that leads to the instability and fracture of rock mass in this stratum. There are no specific research achievements on bedding planes between two different rock types in Badong formation. In order to study the shear mechanical properties of bedding planes between two different rock types. This paper using the software of particle flow code (PFC) and JRC model to establish several typical structures of different roughness coefficient of surface morphology based on the laboratory tests on silty mudstone and marlite in Badong formation. A great deal of numerical shear tests were carried out by ball production, radius expansion and servo infliction. The research results are as follows: First, shear strength of Badong formation is found to vary between that of silty mudstone and marlite isotropic planes by analyzing shear strength of the homogenous bedding planes and inhomogeneous rock types, we can find that the shearing strength in Badong formation is between silty mudstone and marlite isotropic planes and which is closer to the shearing strength of silty mudstone isotropic planes. Second, the basical friction angle of bedding planes between two different rock types in Badong formation is between silty mudstone and marlite isotropic planes and which is closer to the basical friction angle of silty mudstone between isotropic planes. Third, based on the experimental results, an expression is obtained to describe the relationship of the ratio of shearing strength between bedding planes of two different rock types and isotropic planes in soft rock, the rock combination coefficient, and the roughness coefficient. This study has important significance for further research on the shear mechanical properties of bedding planes between two different rock types.

Jan 1, 2015

By R. Stach, S. Gola, P. Zgrzebski, K. Soroko

"At the moment climatic conditions are a primary problem of the exploitation of copper ore. The efficiency of preventive actions in order to improve climatic conditions is connected with the knowledge of changing air in underground excavations. This article demonstrates the analysis of types of ventilation dams which are used in sealing abandoned areas on the maintenance of climatic working conditions in excavations has been conducted at the exploitation in Polish copper ore mines. INTRODUCTION The basis for mining activity performed by KGHM Polska Miedz S.A. is mining copper ores from the deposit lying at depths between 600 and 1,200 m below ground level. Activity has continued since 1963. The copper ore deposit is mined in ‘Lubin’, ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines, where difficult climatic conditions occur. The major factor moulding the climatic conditions in headings is the original temperature of rocks, being the result of geological conditions of the lying of the deposit and the existing geothermal degree. In the faces of present opening-out and preparatory headings, driven from mining areas of ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines in order to open out deeper parts of the deposit, the original temperature of rocks reaches 45°C. Excluding the original temperature of rocks, the following are additional factors affecting the deterioration in the climatic conditions: • thermal properties of deposit rocks, • employed room-and-pillar mining systems, which are characterised by a large surface of exposure of rocks, • using self-propelled mining machines with diesel drive, • a high concentration of mining works, • setting up high-power electrical equipment in headings, • complex structures of mine ventilation networks, • a limited number of ventilating shafts, • constantly longer air-transport routes, • a significant accumulation of water increasing the humidity of supplied air. According to the valid Polish provisions (§21, 2013), the primary criterion of assessment of a climatic hazard is the occurrence at a workstation in an underground mining heading of an equivalent climate temperature of more than 26°C, which temperature is determined according to the following dependence:"

Jan 1, 2019

By A. P. Sasmito

It is well known that underground miners are exposed to one of the most dangerous working environments on earth. As mine delve deeper, the geological factor, mine position and climate condition as well as heat generation from mining machine give rise to the mine operating temperature. This, in turn, has an adverse effect on the environment and thus leads to higher operating costs. Careful estimation and design of air flow rate, spray system, cooling load and additional ventilation auxiliary equipment are of importance to ensure safety, comfort and productivity whilst maintaining low operating cost. A computational fluid dynamics simulation approach is employed to examine underground mine ventilation in a 36 m cul-de-sac of tunnel of coal mine. The model predictions in the turbulent range were validated by comparison with published data. Different turbulence models were tested to select one that yields adequate accuracy and is computationally efficient. Effects of the following parameters are evaluated: tunnel geometry, air flow rate and inlet air temperature. The objective of the simulation is to arrive at an optimal strategy for ventilation and thermal comfort at low cost.

Aug 1, 2013

By D. L. Morgan, J. A. Butterfield

"Geological data, production trends and current projects underway suggest that enough molybdenum will be available from more diversified sources to meet the world's growing demands. The growth in molybdenum consumption has been primarily related to its beneficial effects as an alloying agent in steel. This rapid growth has been deliberately fostered by stable prices, adequate supply and application research. The molybdenum industry is now in a process of change which has been seen in several other metals, such as aluminum and nickel. As supply sources have become more diversified, the market has become more competitive. The recent drop in consumption has led to excess production capacity, accumulation of substantial producer inventories and increased market uncertainties. While consumption is expected to increase in the next two to three years, it will take some time to absorb the excess capacity and inventory. The increased proportion of by-product capacity indicates that prices may become more variable. Producer discipline will be required to prevent serious price erosion in times of surplus. Future prices may not continue to increase with inflation. For the longer term, several factors favour the increased consumption of molybdenum. Engineering requirements are becoming more severe and molybdenum alloys can help to meet these changing needs. In addition, consumers can rely on a large and increasing supply of molybdenum. A 7 per cent growth rate in consumption can probably be sustained through the next decade, but new applications and reasonably stable prices will be needed to make this possible."

Jan 1, 1972

By J. P. Harrison, R. Roostaei

"In this paper we investigate the consequences of using conventional triaxial peak strength criteria in the polyaxial stress conditions that occur around the end of a long circular underground opening. A series of 3d boundary element analyses were performed using Examine3D to determine the stresses induced around the tunnel in different in-situ stress conditions. To discuss the applicability of a triaxial strength criterion in failure prediction, strength factors were computed for both the Ottosen polyaxial strength criterion and the triaxial Hoek-Brown criterion. Assuming that the Ottosen criterion is an accurate indicator of strength factor, the discrepancy from this value due to the Hoek-Brown criterion is the error in prediction.In order to simultaneously show the error in prediction and actual strength factor, a quantitative bivariate colour scheme is used to visualize the results. This allows rapid identification of regions with large error, and where either unsafe or overly conservative conditions occur. We show how the inappropriate use of triaxial criteria rather than polyaxial criteria leads to an under- or over-estimation of strength factor, and can result in uneconomic or unsafe design. Extending the analysis to different in situ stress regimes shows how the in situ stress conditions affect the assessment."

Jan 1, 2015

By M. A. Bérubé, M. Choquette, P. W. Godbehere

"RESUMELa scorie produite par le procédé pyrométallurgique d'extraction Noranda contient environ5% de cuivre. Elle est traitée comme un minerai conventionnel de cuivre au concentrateur de Mines Noranda et les rejets de flottation présentent encore des teneurs souvent supérieures à 0.3% en cuivre. La scorie est principalement constituée de magnétite, de fayalite et d'un verre siliceux. Bien sûr, Ie cuivre y est majoritairement sous forme de sulfures et d'un peu de cuivre métallique. Le verre contient toutefois un peu de cuivre en solution, de 0.14 à 0.33% en moyenne, selon l’echantillon examine, ce qui représente à peine 1% de tout Ie cuivre de la scorie. Dans les rejets de flottation, cela justifie par contre de 15 à 25% des pertes totales en cuivre, Ie reste se retrouvant sous forme de tres petits globules de sulfures de cuivre ou de cuivre métallique, en moyenne de 2 à 3 micromètres de diamètre et bien emprisonnes dans Ie verre.SUMMARYThe slag produced by the Noranda continuous smelting process usually contains about 5% copper. It is processed as a conventional copper ore at the concentrator of Noranda Mines. The flotation tailings still often contain more than 0.3% Cu. The slag is mainly constituted by magnetite, fayalite and a siliceous glass. Evidently, the copper occurs mostly as sulphides and, to a lesser extent, as metallic copper. However the glass contains a small amount of this metal in solution, between 0.14 and 0.33% on an average, depending upon the investigated sample. This represents scarcely 1% of the total copper in the crude slag, but as much as 15 to 25% of this metal in the flotation tailings, in which the major part of the copper occurs as very small globules of copper sulphides or metallic copper with an average diameter of about 2 to 3 um and well-locked in the glass."

Jan 1, 1987

By Zhiwei Wang, Chunsheng Qiao

"Aiming at the problems of the existing calculation methods for the support pressures of shallow tunnels in layered jointed rock strata, by using OAT (orthogonal array testing strategy) and DEM (distinct element method), 12 influencing factors including the thickness of the weathered overburden, and the states of the rock joints were considered. Then, the classification of the loosening zone was analysized. On this basis, by using the DEA (data envelopment analysis) theory, quantitative analysis on the influencing factors was conducted. By analyzing the influence of the key factors, a prediction formula of the boundary of the ringent trumpet-shaped loosening zone was established. According to principles of stress transformation, the formula of support pressures of the loosening zone which could considering the key factors were deduced. Finally, a practical case was introduced and studied to verify the proposed method.INTRODUCTIONIn recent years, various urban subway tunnels are increasingly carried out through jointed rock strata in many cities. Rock masses are discontinuous mediums with fissures, fractures, joints, bedding planes, and faults. The frequency of joints, their orientation with respect to the engineering structures, and the roughness of the joint have a significant importance from the stability point of view. However, there is a lack of understanding about the influence of the joints on the stability of tunnels. Therefore, how to measure the degree of the joints’ influence is a problem that needs to be solved.For the calculation of the support pressures, until now, many research results were focused on soil ground (Bierbäumer 1913; Terzaghi, 1943; Peck, 1969; Sabatini et al., 1999). In terms of site tests and model indoor tests, by measuring strut loads and calculating earth pressure based on strut spacing, the results proposed by Peck (1969) and Tschebotarioff (1973) have been widely used in practice for designing excavation support systems under sand (drained) and clay (undrained) soil conditions. Note that, it is unclear whether these findings could be extended to rock strata. For numerical simulations, how to simulate the states of the rock joints is a key problem that needs to be solved."

Jan 1, 2015

By Earl Gebhardt

"The planning and design of mining panels in the Potash Corporation of Saskatchewan Inc., Lanigan Division mine Block B involved a number of investigative techniques. The techniques utilized to gain insight into the viability of mining included2-D and 3-D seismic surveys, longhole drilling, exploration wells, photo lineament, magnetic and gravity surveys, and actual room excavation.IntroductionPotash Corporation of Saskatchewan Inc. (PCS) owns and operates four potash mines in the province of Saskatchewan. The Lanigan Division mine is located 110 Ian east of Saskatoon, Saskatchewan, near the town of Lanigan.The Lanigan Mine commenced production in August 1968under the ownership or Alwinsal Potash of Canada Limited. The mine was purchased by PCS in 1977.Lanigan Division's productive capacity is 3.4 million tonnes of product per year. Ore is extracted from the "" B"" zone or Layer III or the Patience Lake member of the Prairie Evaporite, more than 1000m below surface . The Patience Lake member (approximately 20 m thick) consists of potash interbedded with salt. The average run-of-mine ore grade is 21070 K20 (Fig. I).The mine was initially developed using the room-and-pillar technique. Improvements in mining resulted in the use or extensible conveyors in long panel rooms."

Jan 1, 1993