Search Documents

By L. D. Haig

"The Texada Mill is a unique iron operation producing High Grade sinter iron concentrate and a by-product copper, gold, silver concentrate. The plant is complex and extremely flexible to handle the many varieties of ore. Two iron concentrates are made and blended. A coarse iron concentrate from primary grinding and a fine concentrate after rougher flotation to remove all the sulphides.All the tailings from iron processing are collected, dewatered, reground and floated for additional copper recovery.The entire milling operation has been carried out in all sea water for seven years and mixtures of sea, fresh, and reclaimed water for ten years prior to that.A very stable float results from the use of sea water at the natural pH8. Reagent Consumption is lower and Metallic Corrosion of mill liners and grinding media is actually less than local fresh water or mixtures of fresh and sea water.Marine growth in pipe lines can be periodically removed by violently bubbling high pressure air up through the water filled mains.Location:Texada Mines is located on tide water on the west side of Texada Island 100 miles northwest of Vancouver, B. C.The Island is served by a 30 car ferry, tug and barge and a scheduled air service from Vancouver to a company maintained air strip near the mine.The climate is moderate with about 30 inches of rain during the winter and relatively dry summers."

Jan 1, 1974

By M. Pourkani, M. Karga, Samid Banis, Andre Laplante, G. Langari-Zadeh

"The Sarcheshmeh mine processes 40,000 t/d of ore grading 0.9% Cu and 0.035% Mo. Grinding is effected in single stage ball mills using 80 mm forged steel balls, with an average consumption of 850 g/t. One of its 5 m diameter, 8 m length ball mills was emptied to measure the ball size distribution. The broken balls were first separated from the total charge, and the remaining balls classified into five size intervals of +7O mm, -70 +60 mm, -60+50 mm, -50+40 mm, -40 mm.The charge was composed of 280,534 balls (excluding broken balls) with a total mass of 305,180 kg. It was found that 4.0 % of the balls were broken; the size distribution of the charge was also markedly different from the desired one, in particular for the small-sized balls. For instance, 9% of the balls were expected to measure 2.54 to 3.18 cm in diameter, but none was found. On the other hand, the amount of top size balls was 30% higher than expected. The radial hardness of balls, which was determined by cutting the balls in halves, showed that the hardness sharply drops when the balls become smaller than 65 mm. The unexpected ball size distribution was attributed to the rapid change in the balls radial hardness. Based on the measured ball size distribution, a new ball make-up charge which uses 80% of 80 mm and 20% of 60 mm balls instead of 100% of 80 mm was proposed and implemented. The effect of the new ball make-up procedure in terms of ball consumption and grinding efficiency is being investigated."

Jan 1, 1999

By D. R. Derry

This paper up-dates an earlier paper by the author on the rate of new Canadian mineral discoveries and the exploration methods which were principally responsible for these finds. He concludes that the ratio of exploration expenditure to production value must be increased if we are to provide sufficient new reserves for the future.

Jan 1, 1970

By J. A. Russell

AS THE LOCAL electric generating plants increased in size and capacity and costs of producing electricity came down, it became apparent that it was no longer good economy to operate individual boiler plants at the Company's various collieries to power steam hoists and compressors. Great economies could be made by burning the Coal at central power plants and using electric power at the collieries. During the period after the end of the war, a steady and continuing programme of replacing first the smaller steam-driven units, and later the steam-driven compressors, was undertaken, and finally the larger hoists, those at No. 12 Colliery in New Waterford and No. 20 Colliery in Glace Bay, were the last units operated by steam.

Jan 1, 1958

By S. Kelebek, B. Nanthakumar

ABSTRACT The sensitivity of sulphide minerals towards oxidation depends on the mineralogical makeup and nature of sulphide ores. This paper focuses on chalcopyrite behaviour in a nickel-copper sulphide- ore matrix that was aged in the mine-site stockpiles. Results of collectorless, collector-induced flotation and recovery by size are presented following a discussion of XPS analysis that was used to gain insight into oxidative alteration of chalcopyrite’s surface chemistry. Chalcopyrite maintains its high flotation activity despite exposure to weeks of oxidative conditions. It is concluded that chalcopyrite is quite tolerant to stockpile oxidation due to various factors related to alteration of its surface chemistry.

Jan 1, 2012

By H. Marquis

This paper is concerned with an analysis of a number of failures of large-size, hypervelocity light gas gun chambers and barrels. A brief description of the light gas gun principle and of the various types of guns is first given. The failures and the investigations carried out are then described in detail, with the failures divided into two groups. The first group comprises those failures caused by certain conditions to which the guns may be submitted, and includes, for example, severe local heating of the bore surface causing hardening and cracking of the steel. These conditions were accidental and steps were taken to prevent them. The remaining failures were due to faults in the material or in the heat-treatment, manufacturing or assembling procedures. Specific problems, such as hydrogen embrittlement, and the use of high strength gun barrels above their ductile-brittle transition temperature by preheating prior to firing, are briefly considered. Some interesting observations are also presented on the use of surface markings, and angles of fracture of large fragments, as an

Jan 1, 1962

"IntroductionThe Chairman, in his speech to this body last year in Montreal, stated that the Dominion Coal Board looked to and depended upon the Bureau of Statistics for statistical material, and the Bureau does collect and publish monthly and annual data on coal. It may therefore be asked why an officer of the Dominion Coal Board should prepare and give a talk on statistics.I would explain that it has been our experience in the Board that, since the supply and consumption of coal in Canada is subject to a seasonal ebb and flow, it can be more profitably studied on the basis of a twelve-month period ending on March 31st than of a calendar year, since the end of March does represent a fairly stable end point in this ebb and flow. The figures are not prepared or published by the Bureau on that basis and it has therefore been thought that a presentation on this fiscal-year period would be of interest. The Bureau of Statistics has agreed that this may be valuable and all the data here presented are based on the reports secured from various sources by the Mining, Metallurgical and Chemical Division, Dominion Bureau of Statistics. The only contribution by either myself or the staff of the Dominion Coal Board has been the tabulation in a different twelve month period, and the comments upon the picture presented.It should be noted that the data for the month of March, 1950, are not available in all cases and consequently the figures for that year contain an estimate for this month."

Jan 1, 1950

By K. C. Lahiri, H. P. Das, G. G. Sarkar

"The petrographic components of any particular rank of coal often show some distinct physical and chemical characteristics. Therefore, their pro-portionate distribution in a coal greatly influences the technological behaviour of the coal.In any size or gravity separation of a coal, the petrographic constituents become segregated to different degrees in some preferred size or specific gravity range. Therefore, a knowledge of the petrographic nature of the washed and/or screened fractions is often considered essential in selecting the most efficient method for coal preparation and in exploring the proper evenues for its utilization.A graphical method is described in this paper to indicate the mineral-matter content and the petrographic components of the washed fractions of a coal at different ash levels of separation in the form of a new washability diagram. This diagram can be conveniently used to assess or predict the petrographic composition of clean coal or sinks corresponding to any desired ash level in the cleans. With the help of this diagram, it is also possible to locate the yield level of cleans at which maximum enrichment of vitrinites and exinites occurs with the least amount of mineral-matter content."

Jan 1, 1971

By C. O?Connor

With ever-increasing global demand for mineral resources, numerous mines are moving towards developing and mining deeper, more complex and lower grade ore bodies. In many cases, mass mining methods (e.g. block caving) are being considered to deal with deeper, lower grade deposits. The body of practical knowledge, however, related to the impacts mass mining methods have on the surface environment in terms of rock mass response, subsidence, etc., is limited, imposing both economic risks to the mine and safety risks to mine personnel. This paper presents the framework for and preliminary results from a large collaborative research initiative between Diavik Diamond Mines, Rio Tinto, the University of British Columbia (UBC) and Simon Fraser University (SFU). The project involves the integration of available subsidence, rock mass, mine operation and monitoring data, together with the advanced application of combined finite/discrete-element modelling codes capable of simulating fracture behaviour, cave propagation and surface subsidence above block cave mines. The main objective of this work is to develop advanced numerical modelling methods to characterize complex rock mass behaviour above block cave mines. The research will also include the study of rock deformation mechanisms associated with the transition from surface to underground mining and the potential interaction between simultaneous open-pit and underground mining operations.

May 1, 2007

By T. E. W. Nind

"A short description of the chamber lift method for producing oil wells is followed by some comments on compressor requirements and gas utilization. A quantitative analysis of the process is presented and, based on this analysis, criteria are suggested for selecting wells for which this type of lift might be suitable. The analysis leads to the conclusions that chamber lift is an efficient producing mechanism for wells having very low productivity indices (say about 0.05 bbl/d/ p.s.i. or less), but that for such wells optimum utilization of injection gas cannot be attained. It is suggested that the gas injection time per cycle should be kept as low as possible, compatible with a small oil fallback volume, and that the cycle frequency should be in the range of 20-40 cycles/ day. For wells with productivity indices of 0.2 bbl/d/p.s.i. or higher, chamber lift is relatively inefficient; how-ever, if well allowables are low it may offer an attractive, low cost, alternative to gas lift or pumping."

Jan 1, 1960

By Norma G. González

La littérature et notre expérience en Bolivie dans une communauté minière très divisée comme celle de Huanuni nous montrent le besoin d?envisager des négociations gagnant-gagnant entre communauté et entreprise minière, non pas comme un point de départ, mais comme un résultat à atteindre, qui nécessite la préparation de conditions préalables. Cela implique fondamentalement de mettre l?accent sur le processus qui permettrait par la suite aux parties de mieux traiter les questions de contenu. Suivant cette hypothèse générale, l?initiative conjointe entre le Ministère des ressources naturelles du Québec et le CECI ?Développement des mécanismes de négociation entre communauté et entreprise minière? peut dégager, après un an et demi d?expérience pilote dans le site minier de Huanuni, département d?Oruro, Bolivie, les leçons préliminaires suivantes. Ce processus requiert: ??Agir, en tant qu?organisme consultant tierce partie, selon des principes et une méthodologie qui relèvent de la Communication publique et de la Médiation ; ??Comprendre et agir à partir de la ?réalité sociale? des parties en présence: l?entreprise minière, l?État et les différents groupes de la communauté; ??Intervenir sur les ?réalités sociales? des parties, par des actions d?éducation et de diffusion dans le but de préparer les personnes, les institutions et les organisations de la société civile, à des changements durables du modèle de communications existante; Approfondir la compréhension de la ?réalité sociale? du conflit (la culture du conflit, les méthodes populaires de résolution des problèmes et de gestion des conflits) afin d?offrire aux bénéficiaires les technologies appropriées pour la transformation de cette culture de confrontation violente en gestion constructive des conflits. Par ricochet, nous espérons ainsi faciliter l?attraction des investissements dans le secteur minier.

May 1, 2001

The negative effects of pyrite and pyrrhotite on thiosulfate gold leaching have been investigated. Possible remedies to reduce some problems are discussed. In a gold bearing pure silicate ore, 92% of gold could be extracted within 3 hours using a solution containing 0.2 mol/L ammonium thiosulfate, 0.9 mol/L ammonia, 30 - 300 ppm copper sulfate and 8.6 ppm dissolved oxygen at pH 10.26. The thiosulfate consumption was 7.1 kg/t under these conditions and could be further reduced to 3.5 kg/t by decreasing the dissolved oxygen to 0.3 ppm. Addition of 16% pyrrhotite or pyrite into the silicate slurry led to a decrease in gold extraction by 2% or 9% respectively and an increase of thiosulfate consumption by 11 kg/t or12.8 kg/t respectively in three hours. Several adjustments, such as increasing copper ion and ammonia concentration and reducing the dissolved oxygen level to 0.3 ppm resulted in increased gold extraction and lower thiosulfate consumption despite the presence of these sulfides.

Jan 1, 2005

By W. K. A. Congreve

Introduction Less than a hundred years ago the engineer was able to do his job without concern for the science that underlay his practices or for the men who operated his machines. But toward the end of the last century science began to be applied to industry, and its success was such that the plant which clung to empiricism was unable to compete with the plant that followed science. Even more recently, the engineer has been forced to consider the men who operate his machines, for modern large-scale industry has given these men education, social security, and power. Hence the engineer can get good, steady labour to operate his machines only if he can offer inducements. Wages are in general outside the control of the engineer, but he is able to control working conditions. This essay is concerned with one factor of good working conditions: safety. The writer became interested in this problem during three months' summer employment as a student at the Sullivan concentrator of the Consolidated Mining and Smelting Company and was surprised at the distance his investigations led him from the field of pure engineering into the fields of psychology, education, and publicity. Nevertheless, because safety has to do with machines and with men who operate machines, and because it profoundly affects plant efficiency, it is the job of an engineer, not of a psychologist or teacher, nor of the salesman publicity expert who is often so unfortunately employed in personnel relations. The size and complexity of the subject has limited the scope of this essay to the consideration of only a few aspects of industrial safety. Considerable attention has been given to the underlying principles, but the mechanical side of accident prevention, the design of equipment, erection of guards, etc., and the very important problems of organization and administration, have not been given attention proportionate to their importance.

Jan 1, 1948

By S. McCalpine, W. Muir, P. J. Downey

"Golden Bear Operating Company Ltd. (GBOC) was a joint venture between Chevron Minerals Ltd. and North American Metals Corp. that was formed for the development of the Golden Bear Project. The mine is located at Muddy Lake, Western British Columbia, approximately 80 km northwest of Telegraph Creek and 135 km west of Dease Lake (see Figure 1). Road access to the mine was developed by Golden Bear and consists of a radio controlled 155 km gravel road originating at highway 114.A feasibility study was completed in 1987 and project approval was finalized in 1988 with Golden Bear issuing a ""Request For Proposal"" for detailed engineering in May 1988. Golden Bear also commenced negotiating with vendors at this time for the supply of the two principal process equipment packages: the dry grinding and classification system and the whole ore roaster package.Process plant engineering and plant construction was completed in October 1989 with plant startup commencing in November 1989. Two months into the commissioning phase it became apparent that the plant, as designed, would not achieve the anticipated production targets.Kilborn Engineering Pacific were subsequently contracted by GBOC to review and modify the plant design, assist the operating personnel with plant commissioning and startup and provide operator training.This Paper describes some of the problems encountered during the startup and the plant modifications incorporated to achieve design parameters."

Jan 1, 1992

By G. K. Lee, E. R. Mitchell

Designers of combustion processes may select aerodynamic conditions which produce only superfine fly ash. Although it is not usually anticipated that this will create a problem, such as has been found to agglomerate in high-velocity gas streams, to plug mechanical dust separators in a short time, and to contribute to atmospheric pollution. The problem is a fundamental one, and may be approached in several ways. The authors, in the course of their combustion research program, had occasion to examine the agglomeration of ash, ranging from sub-micron to 17 microns in size, produced in a (coal and oil) dual-fuel-fired steam generator. Several theories, supported by extensive laboratory studies, have provided some understanding of a probable mechanism of agglomeration. As a result, certain precautions are suggested in the design and selection of combustion processes and equipment.

Jan 1, 1962

"The Detour Lake Mine is located in northeastern, Ontario, approximately 300 kilometres northest of Timmins and 185 kilometres by road northeast of Cochrane. The mill processes a free milling gold ore using both gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 55,000 mtpd at 95 microns with the addition of pre-crushing upstream of the SAG mill.The present paper will describe the methodology used to successfully prove that gold of the Detour Lake Mine ore is mostly concentrated into the fine size fraction of the blasted rocks. It will describe the various options possible to create value from this ore property.IntroductionThe purpose of this test work was to determine the grade of the pebbles and consider if there was value into discarding the pebbles and replacing the material by fresh feed.1. Pebble samplingThe pebbles were sampled and assayed for grade every day for 3 months. After 3 months of sampling, the results showed that the pebbles only carried 28% of the fresh feed grade. This phenomenon can possibly be explained by the fact the gold is located into area of fracture in the rocks.January-March 2014 – Pebble assay average• Line #1 = 0.222 g. Au/t• Line#2 = 0.275 g. Au/t• Head grade = 0.88 g. Au/t2. Crushing and grinding circuit surveysWith the above information, a grinding circuit survey was planned. The purpose of the survey was to build a JKSIMMET model of the grinding circuit for mill optimization but also to understand the deportment of gold into various size fractions that may explain why there is so little gold in the pebbles. All streams and size fractions was analysed for particle size analysis and for gold.Since Detour has dual grinding lines, both circuits were sample at the end of May. Two supplemental survey of the secondary crushers were also done and a survey of the gyratory crusher."

Jan 1, 2016

By D. E. Parson, W. A. Morgan

This paper offers a brief review of current literature pertaining to vacuum degassing or vacuum casting of steel as practiced in the U.S.A., Germany and the U.S.S.R. The advantages of vacuum degassing of large forging ingots, heavy section casting, for the conversion of rimming bessemer steels to killed steel and for the production of transformer steels are discussed. Operating pressures, reduction in gas contents and improvements in hydrogen segregation, steel cleanliness and mechanical properties, obtained with the various techniques, are described. The paper includes a description of an experimental vacuum stream-droplet degassing unit and some preliminary results obtained at the Physical Metallurgy Division Research Laboratories Department of Mines and Technical Surveys, Ottawa on laboratory steel melts. Experimental 500 lb direct arc, basic melts have been spray cast into either ingot moulds or dry sand moulds, held inside a vacuum tank. Also 500 lb melts have been

Jan 1, 1961

By M. J. Beus

Many mines in Canada, the United States and South Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due to the excessive weight. It has been suggested (DeLorme, 2000) that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm (13/4 in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg (10 ton) skip could exceed the safety factor of the rope. To improve on the current understanding of the mechanical behaviour of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modelling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca, 1999), is used to simulate the structural behaviour of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modelling on the wire rope will be discussed.

Jan 1, 2002

By Francoi Robert, Andre J. Audet, Alex C. Brown

"The Sigma gold deposit is in a band of deformed metavolcanic rocks that are cut by an irregular mass of porphyritic diorite and by narrow undeformed feldspar porphyry dykes. The gold is in veins consisting mainly of quartz and tourmaline with minor pyrite, carbonate, chlorite, scheelite and free gold. The results presented here concern the structural setting of the ore and are based on a study of the mode of emplacement.Two principal types of veins have been recognized: subvertical and oblique veins. Both types are contemporaneous, mechanically linked and postdate regional deformation. The sub-vertical veins are composed of numerous mineralized lenses that occupy the central part of ductile shear zones of great lateral and vertical extent. Normally, several lenses occur in the same shear zone. The vein material seems to have resulted from incremental filling of openings by repeated vertical movement along rupture planes developed in the central part of the shear zones.The oblique veins are small elliptical lenses of ribboned vein material which formed essentially by progressive vertical opening of oblique fractures. Two types of oblique veins are known: one is restricted to feldspar porphyry dykes, within which they are arranged in an en-echelon fashion; the other is of greater extent and is not restricted to one rock type, but tends, however, to occur in the more competent porphyritic diorite.Vein orientation and mode of formation suggest that both sub-vertical and oblique veins developed during progressive deformation associated with the formation of the ductile shear zones. The latter probably formed in response to a compression that took place late in the tectonic history of the host rocks at Sigma."

Jan 1, 1983

By G. W. Govier

Measurements of the settling rates and the rheological behaviour of heavy media formed of fine suspensions in water of each of magnetite, ferrosilicon, and galena have been made. For media ranging from 1.6 to 2.8 specific gravity the settling measurements gave initial settling rates of from 0.5 to 0.01 ?cm. 'Per minute for magnetite; from 4.0 to 0.8 cm. per minute for galena; and from 35 to 1.6 cm. 'Per minute for ferrosilicon. These measurements indicate the ?relative stability of the suspensions and should be helpful in establishing the useful specific gravity range for each medium. Measurements of the consistency of the media were made with a Fann Model 35 rotational viscometer. Aibnormal or non-Newtonian behaviour was observed in the case of each media, the apparent viscosity being dependent upon the rate of shear or the intensity of motion. Measurements were made over the rate of shear range of 10? to 1,000 reciprocal seconds. The apparent viscosities of the magnetite media ranged from 450 down to 4?0 centipoise at 2.30 specific gravity, and from 2,450 down to 700 centipoise at 2.80 specific gravity. In the case of the galena media, the variation was from 40, through a minimum of 6, to 10 centipoise at 2.20 specific gravity, and from 950, through a minimum of 180, to 450 centipoise at 3.6 specific gravity. The ferrosilicon suspensions exhibited apparent viscosities ranging from 42, through a minimum of 5.6, to 9 centipoise at 1.9 specific gravity, and from 160, though a minimum of 35, to 85 centipoise at 2.8 specific gravity. The dependency of apparent viscosity or consistency upon intensity of motion is considered to be of particular significance in applications of heavy media where the medium is in rapid motion.

Jan 1, 1957