Search Documents

By P. P. Sinha, D. N. Bhatia, B. R. Ghosh, R. K. Gupta

Medium carbon, low alloy, high-strength steels containing Ni, Cr, and Mo are used for the fabrication of various types of high-strength fasteners required for launch vehicle structures. Cold heading properties and response to hardening and tempering are the essential requirements of the material for fabrication and application, respectively. Combining these two requirements is essentially warranted in high-strength fastener-grade steels. Cold heading properties require ductility, which can be achieved through spheroidizing treatments. In the absence of a suitable spheroidizing cycle for medium carbon 3.8 Ni, 1.8 Cr, 0.3 Mo steel, experiments were carried out with a theoretical understanding of the alloy system. This paper presents the experiments and results obtained after a spheroidizing treatment, which was carried out to optimize the process. Hardness measurements were carried out and microstructural studies were conducted to assess the spheroidization process and to determine the optimal spheroidization parameters.

Jan 1, 2007

By R. H. Batey

"The process control and cost of monitoring mining slurries is normally accomplished using a continuous mass flow system, conventionally embodying a volumetric magnetic flow meter and nuclear density meter. DuPont’s Maxville Mine at Starke, Florida, USA was chosen to examine costs associated with performance of a nuclear density meter. Since it is typical of many mid-sized establishments and has a long history in their use. The published accuracy under ideal conditions of a nuclear density meter is ± 1.0%, but in practice considerable ambiguity of cost in annual production implies ± 2% at best. Using such accuracy in a 400mm (16”) pipe carrying zircon slurry at 75,000 tons/day, the cost of ambiguity, together with initial and running costs, amount to nominally $962,000 per year.Such cost leaves much to be desired. This paper describes an unique continuous, direct mass per unit volume Density Meter used for mining slurries in pipe sizes up to 1000mm (40”), which significantly reduces the cost of ambiguity of measurement and running costs. At the same time the disadvantages of nuclear devices are obviated.In an effort to reduce costs, a 400mm non-nuclear Density Meter was installed at the DuPont Maxville mine. A typical on-site accuracy can be shown to be ± 0.285%, whereby the cost of ambiguity, initial and running costs in the example above shows an annual improvement of $78,660, a reduction of over $880,000 per year.Even higher cost savings may be demonstrated with mass flow systems having gas entrainment compensation. Unlike nuclear and other inferential density meters, the signal quality of this non-nuclear Density Meter is totally unaffected by entrained gas found in mining slurries. This non-nuclear density meter is then ideally used with a vortex velocity domain sonic flow meter, and provides for the first time compensation in wet density or dry % solids, as well as wet or dry mass flow of mining slurries with entrained gas, resulting in enormous reductions in cost ambiguity."

Jan 1, 2013

The Stability Graph Method is widely used in Canadian underground hard rock mines for open stope support design and is frequently used in the mine planning phase to assess the viability of stope geometries and to determine maximum permissible spans. The Method is well accepted due to its simplicity and suitability to a wide range of mining methods requiring the use of sublevels to access and extract the mining blocks. While this Method is reliable in situations where the maximum induced tangential stress creates adequate compressive stress keeping the face in a state of confinement, the Method fails to reflect the effect of low confinement caused by lower compressive stresses and instances where tensile stresses are developed. In this paper, a new Rock Stress Factor, A?, an update to the original Rock Stress Factor, A, is proposed, which will reflect the impact of low confinement or overstress regime on critical face stability. Two case studies, based on two Canadian operating gold mine shows that using the new Rock Stress Factor A? to predict the stability of stope hanging-wall and footwall gives better agreement with the CMS survey results, compared with the prediction using the original rock stress factor.

May 1, 2011

By Alfred W. G. Wilson

In this paper is presented a review of the changes that have taken place in certain Canadian non-metallic mineral industries since 1909. The fifteen-year period 1909 to 1923, inclusive, has been selected for two reasons. In the first place, statistical treatment of the subject under review has been nearly uniform throughout the period. In the second place, this decade and a half is itself further subdivisible into three well marked quinquennial periods, the middle one covering the period of the great war when industrial conditions were greatly disturbed. It then becomes possible to institute certain comparisons between equal periods before and after the war disturbances. The items selected for inclusion in this review are certain of the more important members of that class of minerals usually grouped together under the heading of non-metallics. They are all minerals of which Canada is known to possess important resources, and which are indispensable to many of our greatest manufacturing industries.

Jan 1, 1925

By Jessica Egan, Daniel Hodouin, Mohammed Reza Khalezi, Steve Bellec, Claude Bazin, Carl Duchesne

"A model for gold leaching was developed and implemented into a simulator. The simulator uses a description of the ore that is based on the mineral composition and precious metal content. The model accounts for the distribution of minerals and precious metals through the size intervals. An ore texture model based on precious metals and minerals grain sizes within the ore is used to predict the exposed surface of the species in the various size intervals. A model is proposed to predict the rate of dissolution of any species dissolution using the exposed surface, particle size, cyanide and oxygen concentrations, temperature, pH and agitation. The flow of slurry through a leaching tank is modelled using a parallel arrangement of perfect mixers to simulate a bypass and a Cholette-Cloutier mixer model. The simulator can be used for circuit optimization but was developed to provide an environment for learning the basic concepts of process analysis methods. Examples are given to illustrate the application of the simulator for planning tracer tests and sampling campaigns.INTRODUCTIONThe constant pressure to improve the operation of processes that are already close to optimum imposes to plant engineers to be aware of the available process analysis tools and to be able to use them to assess process operation and make a diagnosis to possible problems. Some of these tools are:•,Sampling the streams of a process;•,Data reconciliation;•,Analysis of mixing in reactors;•,Estimation of rate parameters;•,Optimal tuning and flow sheet modification;•,Automatic control and real time optimization.Although some of these tools are part of the curriculum of many university engineering programs, the students are not exposed to actual process analysis problems. In addition the complexity of the ore dressing processes compounded with unavoidable measurement errors and plant disturbances can discourage many motivated engineers. These factors often lead to an incomplete valorization of the collected data and a poor return on the investment associated with the sampling, testing and analysis of the samples.Simulators are readily available for process optimization (Yalcin and Shang, 2006) by allowing:•,The simulation of various flow sheet configurations;•,The simulation of a change of operating conditions;•,The simulation of various control strategies;•,The training of plant operators.However few simulators have been developed with the objective of providing an environment for training plant engineers and technicians to the use of tools for process analysis and optimisation."

Jan 1, 2008

By Rodrigo Toro, Ivan Yutronic N

"The Copper Concentrator Plant of Compañía Minera Doña Inés de Collahuasi (CMDIC) is composed of three grinding lines, the third one being the largest. Due to the capacity feature of the third line, specially its SAG mill, it is a priority that the advanced process control team of the Company deploys a supervisory control strategy that allows this unit to operate in an optimal way, in order to achieve the maximum productivity at minimum cost. It is in this kind of tasks where advanced control applications play a key role in obtaining the best economic profit of the process.The advanced process control team, formed by people from Informatics, Automation and Operations of CMDIC have assumed the challenge of generating the transition from a manual SAG Mill 1011 operation (40 x 22 feet, the largest copper SAG mill of the world), to a fully automatic SAG Mill using a multivariable control strategy instead of a rule based on expert control system (widely used in industrial mining process control applications).Therefore, CMDIC decided to work together with Honeywell APC Team implementing an advanced automatic control strategy for the SAG Mill 1011, using for this purpose a technology called Model Based Predictive Control (MPC), based on a variety of control methods that uses dynamical models of the process, obtained from input/output data, in order to print the process knowledge into a group of mathematical relationships that links the constraints (controlled variables) with available commands (manipulated variables) and measured disturbances.The main objective of the advanced control strategy is to ensure process government, tending to throughput stability and optimization, by the execution of coordinated control actions, proactively avoiding measured disturbances effects and the SAG mill overloading.The most important benefits of using a multivariable control strategy are: the automated operation of SAG mill 1011 (that was manually operated before the implementation of this application), a safer, more coordinated and more stable process operation, achieving through this an increase of throughput and a decrease of specific energy consumption, controlling the amount of oversize material production, power consumption, mill loading, noise and torque. In addition to the operational results, this challenge has consolidated a control team, with the participation of engineers and operators, diminishing the typical implementation time and achieving a greater use of the application in a short time."

Jan 1, 2010

By W. E. Roscoe

The probability of making an exploration discovery in Canada can be calculated from Derry's (1970) data on exploration expenditures and number of discoveries over the last nineteen years. Considering an average exploration "try" to be $30,000, the probability of a discovery with one try has decreased tenfold from about 0.01 in 1951 to 0.001 in 1969. A plot of these probabilities can be extrapolated to the future, giving a 1969-71 three-year average probability of 0.00096 with 90 per cent confidence limits of 0.00042 and 0.00153. Using this probability, various calculations can be made, such as (1) the probability of making at least one discovery for any given exploration expenditure, (2) the probability of ultimate ruin or survival of the exploration investment process and (3) the expected value of an exploration investment. There is a critical minimum amount per discovery that must be re-invested in exploration, no matter how large the original investment is, for exploration to survive at all in the long run. Currently, this critical minimum is $31,200,000 with 90 per cent confidence limits of $19,600,000 and $71,400,000.

Jan 1, 1971

By J. Paraszczak

ABSTRACT Diesel-powered loaders are a pillar of modern underground metal mining. As these mines are getting deeper and hotter and the emission regulations stricter, ventilation costs are soaring, affecting production cost. Also, the cost of diesel fuel is expected to rise. These may make the use of diesel engines more problematic. Electric load-haul-dump machines (LHDs) are an interesting alternative. This paper compares features and performance of diesel and electric, cable-powered LHDs. It overviews equipment offerings, and compares, analyzes and discusses technical parameters, operational problems and cost issues. The paper gives some conclusions about electric LHD applicability and performance, indicates possible applications, and suggests further research work.

Jan 1, 2013

By M. C. Bétournay

Mine site infrastructure for storage and delivery of hydrogen must be standardized and acceptable for routine and safe industrial use before fuel cell technology is adopted as a major power source. An initial study reviewed possible options for production, storage and delivery of hydrogen for underground equipment. The high level review included assessment of economic, operational, technical, and health and safety risks. Following this review, a subsequent theoretical study to select typical minesite infrastructure and for construction at an operating research mine is outlined.

May 1, 2007

By J. A. Harle

Introduction When considering power in Alberta, there automatically come to mind ideas of either hydro or thermal generation, leaving in one's thought an uncertainty as to which one would propose. There is frequently an obvious source of power in some locations on our fastflowing rivers, the major possibilities being described in the report on Surface Water Supply and Water Power of Alberta issued by the Alberta Government in 1948, but it must be realised when reading that report that the sites so described will require extensive geological and other surveys before they can be exploited, and account must be taken also of the transmission distances involved in each instance. From a conservation point of view, where water power can be economically developed and power transmitted to the load centres, this should be done, and our thermal resources should be husbanded for our coming generations, especially if our water resources are falling owing to glacial shrinkage.

Jan 1, 1951

By T. G. Joseph, M. J. Bolster

ABSTRACT This paper explores passive seismic measurement as an alternative, nonintrusive approach to conducting annual brake testing on surface mine sites. Dictated by the test site location, this evaluation adhered to the brake testing procedure as per British Columbia occupational health and safety regulations. Results showed excellent correlation to those reported via conventional practice: Comparing stopping distance, time, and velocity for the proposed instantaneous passive seismic versus conventional approaches, less than a 0.5% variance was evident. A viable alternative, the passive seismic approach, allowed an entire fleet of trucks to be sequentially evaluated for annual brake testing without disrupting operations by installing mechanical testing equipment.

Jan 1, 2012

By Chris Fleming, John R. Goode, James Brown

"Data will be produced from two uranium feasibility studies that were conducted in 2008, both involving uranium recovery from leached slurry by resin-in-pulp (RIP) with strong base resins. Excellent metallurgical results were produced in RIP pilot plants in both studies, and the loaded resins were eluted with strong sulphuric acid and recycled to RIP in an integrated process. Resin losses by either abrasion or mechanical breakage were immeasurably low.Metallurgical results from these two campaigns will be presented, along with an economic analysis of RIP versus the alternative process of CCD or filtration and solvent extraction.INTRODUCTIONThe recovery of uranium directly from pulp with strong base resins in RIP contactors was practiced commercially in the USA in the 1960s, but the process never established itself as a viable alternative to solid/liquid separation and solvent extraction. This was due mainly to the necessity to do a sand-slime separation partially resulting from the unavailability of coarse resin beads, inadequacies in the design of the RIP contactors and screens to separate resin from pulp, as well as problems with the strength and durability of resins in agitated pulps.There have been significant advances in the last 30 years in each of these areas. All the commercial resin manufacturers are now producing very tough, durable, strong base resins, and are manufacturing them in a large bead size that is better suited to RIP applications. In addition, with the emergence and wide spread implementation of the carbon in pulp process in the gold industry in the 1980s, many innovative techniques for preparing leached slurries and separating carbon from pulp have become firmly established. These techniques have proven to be equally applicable to resin separation from pulps in RIP contactors."

Jan 1, 2010

By Jodi Roberts, Curtis Deredin, Jean-Guy Paulin

"Since the establishment of the Six Sigma quality improvement program in 2001, several projects have been successfully carried out in the copper-lead, zinc, copper separation, lead upgrading and bulk flotation circuits in the Brunswick Concentrator.This paper provides an update on the process improvement initiatives that have taken place since 2004 using the Six Sigma methodology:•,The recirculation of warm water to the flotation circuit (to save on energy costs)•,Installation of a heat recovery tower to recuperate the heat lost from the zinc dryers•,Installation of an extra row of cleaner-scavenger cells for the copper-lead circuit for extra capacity, and a new reagent scheme for the copper separation circuit that have increased copper and lead recoveries.INTRODUCTIONThe Brunswick Mine Concentrator (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The concentrator utilizes selective flotation to produce zinc, lead, copper, and bulk lead/zinc concentrates. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.Figures 1, 2, and 3 illustrate the historical annual average metallurgical performance and process improvements achieved at Brunswick Mine for the zinc, lead and copper concentrate products. The objective is to continuously direct metallurgical performance towards increasing grades and recoveries while minimizing operating costs."

Jan 1, 2008

By G. E. Norman, A. L. Mckague

"The new smelting process commenced operation in 1978. The pelletizing and sinter plants were replaced with slurry-fed roasters and the blast furnaces with electric furnaces. The existing converter aisle and matte handling facilities remained unchanged.Process DescriptionNickel-copper concentrate is partially roasted in two slurry-fed fluid bed roasters. After gas cleaning, the sulphur dioxide gas is transferred to the acid plant. The roaster product is conveyed to two electric furnaces for smelting to produce a waste slag and furnace matte. The slag goes to the disposal area and furnace matte containing the metal values is processed in the converters for further removal of iron and sulphur.The final matte containing about 75 per cent metal values is shipped to the refinery in Norway.The commercial smelter was designed for 2135 tonnes per day of concentrate, with an availability of 85% . Roasters and electric furnaces were sized at 117 per cent of design, or 1250 tonnes per day on each of two lines. Concentrate storage capacity in the plant is sufficient for two to three days' plant operation.The new smelting process will be discussed under the following headings:Concentrate Slurry HandlingFeed PreparationRoaster OperationRoaster Gas CleaningCalcine TransferElectric Furnace Operation and Process Control Converting and Matte HandlingUnder these headings, process control , equipment changes, and plant performance after three years' operation is reviewed. A brief discussion of accident prevention , and working environment is also included ."

Jan 1, 1984

By W. van der Merwe

ABSTRACT With the gold industry processing more complex ores, the online measurement and control of cyanide addition to the gold leaching circuit has become more critical. This paper compares the two commonly employed ‘free’ cyanide online analysis methods (amperometric and potentiometric endpoint silver nitrate titration) with the rhodanine endpoint silver nitrate titration and ion selective electrode methods common at site laboratories. Measurement differences between these methods are presented and discussed for cyanide solutions containing copper and zinc with varying cyanide to metal ion ratios. The resulting cyanide available to leach gold is also compared using these measurement techniques.

Jan 1, 2013

By A. D. Thomas, V. N. Rampton, S. Paradis, C. F. Gleeson

"A shallow till sampling program was completed on a 1 km grid over the St . George Batholith in southern New Brunswick. The ""B"" soil horizon was analyzed for Cu, Pb, Zn, Ag, Co, Mo, U and Sb and the heavy minerals from the ""C"" soil horizon were analyzed for W, Sn and A u. The results delineated four of five recorded W occurrences, three of four recorded Mo occurrences, all recorded Cu occurrences and one recorded Au occurrence. The results indicate that shallow till sampling in conjunction with bedrock and Quaternary mapping can inexpensively define exploration targets in terrain similar to that underlain by the St. George Batholith.A similar program was carried out in eastern Ontario involving the analysis of four separates from the till, the ""8"" soil horizon, the -50 mesh fraction, the -250 mesh and the heavy mineral fraction of the ""C"" soil horizon and humus. Also sampling was carried out near known gold occurrences at closer spacings. Regionally, anomalous results from all sample media clearly defined a large auriferous shear zone and associated splays. Over one known showing all media clearly defined the showing and a secondary zone. On the regional scale the heavy mineral fraction gave the best anomaly definition and contrast, but the -250 mesh fraction was found to be the most cost effective for defining exploration targets. For detailed surveys, humus was found to be cost-effective."

Jan 1, 1986

By A. S. Bayne

WITH the great increase in the use of power-driven machinery in industry, and consequent large-scale operations, the hazards to which , workmen are exposed have become much more numerous than at the beginning of the century. This is especially noticeable in mining. In the past thirty years or so, improvements in methods of excavation and metallurgy have made possible the exploitation of deposits which would have failed to make ore in previous years. This improvement, together with the in-creased use of machinery, has facilitated the mining of tremendously greater tonnages with a marked decrease in unit cost of production. This 'speed up' in mining creates numerous problems demanding close attention of operators and necessitates careful prep;tratory planning, as well as diligent supervision of actual operations. Underground openings increase in size so fast, and all phases of mining, mucking, and transportation proceed at such a rate, that a short period of reduced vigilance on the part of operators . results in disaster, both from the standpoint of safety and economies. Happily, the challenge of increased hazards has been successfully met by a general application of the slogan 'Safety First'. Today, we have large manufacturing concerns devoted entirely to the development and production of safety equipment for the protection of workmen in various branches of industry. Machinery manufacturers, in co-operation with their mining customers, have included the best possible in foolproof devices in the manufacture of hoists, compressors, boilers, electric motors, and equipment of all kinds. Mining companies and private individuals spend thousands of dollars and devote a great deal of time to research with the single object of preventing accidents and combating miners? diseases. Governments throughout the world have written regulations into their statures for the protection of miners and operators. Staffs are appointed to enforce these laws and investigate accidents to ascertain means of preventing them for the future benefit of the industry.

Jan 1, 1938

By Selwyn G. Blaylock

There is no more important problem today than industrial relationship, and probably none that is receiving more thought. But in these days of Epie and Utopia, one has to be rather careful in speaking on this subject. Consequently, for fear that my plea for taking the working man into the family might be misconstrued, by some, as a step towards communism or socialism, I would like to say at the outset that I believe that, so long as we have human individualism, human ambitions, human hopes and fears, straight socialism is as far off as the Millennium. The same applies to communism, which only differs from socialism in that the communist realizes that his ideals can only be attained by massacring millions and destroying all that we hold sacred. Each still looks to Russia for inspiration and guidance, totally disregarding the Soviet swing-back to individual contract work and differential wage scales. They seem to be oblivious of the tyranny and repression in the present Russian system, and get very restless when reminded of it. In spite of the fact that the standard of living in civilized countries has improved tremendously and is still improving, we find that, every seven or eight years, production in many lines has outstripped consumption, and we have had panics or depressions of greater or less magnitude, accompanied by extensive unemployment. It is evident to every thinking person that there must be no little inefficiency in the control of industry. For four long years, governments and industrialists have striven to find the key to solve the present problem. Many countries are getting back to a position approaching normal-Canada probably more so than most. None, however, can feel assured that they have actually cured the situation. All kinds of schemes have been developed; tariff barriers have sprung up over-night where none existed before; currencies have been inflated to gain added security in the home markets and to try to gain advantage in export trade; and each country watches the movements of the others with fear and mistrust. I am not prepared to formulate a full solution of our troubles, but I hope to be able to demonstrate the feasibility and wisdom of the type of industrial relationship I advocate, and also that it may be a large, and possibly an essential, step towards the solution of our difficulties.

Jan 1, 1935

By Alexandra Kozak, Rodrigo Costa, Bob Fukuhara

"The Jacobina project in Bahia, Brazil commenced operations in 2004 with a design capacity of 4,200 tpd. A project development plan to increase plant capacity to 6,500 tpd will be discussed. The project included an evaluation of the existing circuit and addressed bottlenecks in the crushing, milling, sedimentation, leaching and tailings transport. These circuits and the methodology used to provide higher capacity will be presented.INTRODUCTIONThe Jacobina mine is located in the state of Bahia in northeastern Brazil approximately 330 km northwest of the state capital city of Salvador and 9 km from the town of Jacobina. The Jacobina Mine (Figure 1) is owned by Jacobina Mineração e Comércio, a wholly owned subsidiary of Yamana Gold Inc.The gold mineralization of the Jacobina mine is hosted within quartz pebble conglomerate reefs of the Serra do Córrego Formation which together with the Rio do Ouro Formation forms the Serra do Jacobina mountain chain.The Serra do Jacobina mountains have been mined for gold since the late 17th century. Since the 1970’s, the Jacobina mine has been operated by Anglo American, Williams Resources Inc., Desert Sun Mining Inc. The mine is currently owned by Yamana Gold Inc.In December of 1998, operations at Jacobina were suspended and the property was placed under care and maintenance. Desert Sun Mining Inc. began exploring the property in 2002 and eventually purchased the Jacobina mine in 2003. In 2003, a feasibility study was completed that evaluated the economics of re-developing the mining operations and expanding gold production. In 2004, refurbishment and re-development of the mining operations began and the milling facility throughput capacity was expanded from 1.08 to 1.512 Mtpy (3,000 to 4,200 tpd). The milling operations were commissioned in the 1st quarter of 2005 and commercial production was declared 1 July 2005. In April 2006, Yamana Gold Inc. acquired the Jacobina mine through its acquisition of Desert Sun Mining Inc."

Jan 1, 2008

By L. M. Wang, G. P. Jiang, Y. Jiang, Liao. W. S.

ABSTRACT The authors measured porosities and permeabilities for cores from a low-permeability sandstone uranium deposit in Inner Mongolia. Features studied included fine pore structure, mineral composition, cation exchange capacity, granule appearance, and cementing features. In general, grading of the grains was relatively poor, which decreased the radii of the pore channels. The pore throat distribution was significantly heterogeneous. Pore channels ranged from small to large, but the lack of large pore channels led to low permeability. Cementation by calcite and clays, including montmorillonite, chlorite, and kaolinite, resulted in pore channel narrowing, further decreasing the permeability of the formation.

Jan 1, 2014