Search Documents

The Porgera Joint Venture commenced production during September 1990. A small tonnage underground mine extracts high grade gold ore using small scale stopes. Conventional drill and blast methods are used for development and production mining. Ground support is effected with Splitset anchors, grouted rebar bolts and grouted cable bolts. Splitsets and grouted rebar can be installed by mechanised means. Vertical crater retreat, slot and massfire, and modified VCR stoping tech- niques are used at Porgera. Stopes are backfilled with a relatively strong cemented rockf ill. Future stope sequences require recovery of pillars beside and under filled stopes.

Jan 1, 1991

Up to the end of World War n, flat-back cut and fill stoping with or without square sets was the universal method of ore extraction. Rapid changes in practice occurred during the post-war years; first, ore extraction was fully mechanized; secondly, the stope design for new levels, notably No. 17 Level Zinc Corporation Ltd. and No. 19 Level New Broken Hill Consolidated Ltd., was modified to suit this mechanization; and thirdly, sub-level and shrinkage stopes were developed in orebodies where cut and fill methods would be uneconomical. The following is a brief survey of the changes that have occurred-most of which were inaugurated during the last five years.ROCK DRILLINGDuring 1951 open stoping was investigated in detail. In order to reduce steel handling problems, forged steel onepass detachable bits were introduced, but were soon superseded by the "Swedish method". Investigation showed that when using a bar and arm mounted 3-in. drifter the overall drilling time was approximately 6 min. per ft. compared with 4 min. per ft. using the light jackhammer-airleg combination with 1-in. hex. by 4-in. collared shank tungsten carbide-tipped steel.Although competitive with tipped steels on a cost per foot drilled basis (excluding miner's time), detachable steel bits proved most unsatisfactory for hard drilling conditions.Rapid blunting necessitated frequent bit changes and thus caused lost drilling time. This, together with rapid gauge...

Jan 1, 1957

By J Gresham, A Turichshev

Ore from Henderson’s 7700 Southwest panel cave is transported between the production and truck haulage levels through a series of orepasses. A typical orepass complex consolidates dump points from four production drifts into two long bored raises feeding into a single truckloading chute. The system typically covers a vertical extent of 200 m and a lateral extent of 90 m. In the process of commissioning several initial orepass complexes, challenges with preferential draw in the long bored raises were observed. Preferential draw occurs when one long orepass mobilises much sooner and/or flows significantly faster than the other orepass. This has negative implications for orepass availability in the production drifts. As future mining at Henderson relies on the construction and use of such orepass systems, the development of appropriate design criteria and practical solutions to existing flow problems was necessary.A series of PFC3D numerical models were developed to assist in identifying the factors influencing preferential draw and possible corrective measures. The models helped to identify two primary factors that caused the preferential effect: the relative elevation of the brow at the bottom of each long bored raise, and the location of the bin used to funnel fragmented rock from both raises into the chute. This paper covers the initial design of the orepass complexes at Henderson, results of the numerical models, mitigation work done to date on existing orepass complexes, and design criteria for future construction.CITATION:Gresham, J and Turichshev, A, 2016. Correcting preferential flow problems in long orepass systems at Henderson Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 549–554 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M Eggers, H Baxter

This paper discusses the geotechnical condition of bedding shears and small- and large-scale faults and shears in Archean banded iron formation (BIF) bedrock, based on observations of core and televiewer images. Information that can be collected includes the orientation of defects, infill thickness, strength and material type, defect shape and surface roughness.The spacing and continuity of bedding shears may be critical to slope design where performance is structurally controlled with bedding dipping out of a wall. The intensity of development of the bedding shear is a useful indicator of the amount of shearing a bedding surface has been subjected to. This can allow for engineering judgement to be used in adopting peak or residual shear strengths along defect surfaces when developing the design.The spacing and continuity of bedding shears may also contribute to the blockiness and degradation of a rock mass where the structural orientation is otherwise favourable. Additionally the condition, thickness and strength of infill of major fault structures can affect slope design and performance, depending on orientation.Comparison of the condition of structures observed in core with the corresponding in situ televiewer image has been made to assess what characteristics are most accurately captured by each technique and whether the additional information gathered from using the televiewer technique is justified by the cost. The question of whether the data collected by a televiewer is sufficient to ultimately replace the need for core is considered.CITATION:Baxter, H and Eggers, M, 2013. Fault and shear characterisation in archean banded iron formation bedrock - a comparison between core and televiewer data collection techniques, in Proceedings Iron Ore 2013 , pp 47-56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Cadia Geology Team

The Cadia Hill Gold Mine, located near Orange in Central Western New South Wales, is owned and operated by Cadia Holdings Pty Ltd, a wholly owned subsidiary of Newcrest Mining Limited. Construction including pre-strip mining occurred from 1996 to 1998. The mine was officially opened in October 1998 following commissioning of the concentrator and mine fleet in June of that year. The Cadia Hill orebody is a porphyry related gold and copper system. The final pit has a strip ratio of approximately 1.3:1.0. Mining is undertaken on 15 metre benches using large capacity diesel hydraulic face shovels at an annualised rate of up to 70 Mtpa. The concentrator is currently rated at 17Mtpa and includes the worldÆs largest single line grinding circuit. The feasibility Mineral Resource was estimated at 352 Mt at 0.63 g/t Au and 0.17 per cent Cu. Initial reserves totalled 200 Mt at 0.74 g/t Au and 0.17 per cent Cu yielding a mine life of approximately 12 years. During the pre-production period mine geology systems were developed to support the operation. By design these systems were intended to add value to the business through minimisation of material miss-classification, provision of accurate and timely production information and mapping and reconciliation as a continuous model improvement tool. Variances that would prove to be material to the life of mine plan were recognised during the first year of production. These included identification of additional ore tonnes, higher copper grades and higher gold recoveries relative to the model. Gold grades and copper recoveries also reconciled favourably. Testwork was undertaken to determine the underlying causes of each variance. Re-modelling was then undertaken to capitalise on those variances. The Cadia Hill Gold Mine life of mine plan was re-evaluated with updated geology, grade, geotechnical, metallurgical and environmental inputs. Operating strategies were also reviewed and revised. Despite application of reduced metal prices in the evaluation, the outcome was one of extended mine life with more metal produced at lower cost. Development of robust mine geology systems, including a pro-active reconciliation process contributed to tangible improvement of the Cadia Hill Gold Mine operation. On-going system development and improvement initiatives are planned to add further value for the future.

Jan 1, 2000

By Thompson D. R, Milton R, Perry K. M A

From the Department for Research in Industrial Medicine (Medical Research Council), The London Hospital; and the De Havilland Aircraft Company:M.R.C. INVESTIGATIONS IN 1936In 1936 the Industrial Pulmonary Disease Committee of the Medical Research Council investigated both clinically and radiologically a group of fifty workers who had been exposed for a number of years to the inhalation of alumina in the reduction factory of the British Aluminium Company. The results are shown in Table 1.They also considered the sickness records of all the workers (Hill, 1936), as compared with those in other parts of the factory (Table 2).

Jan 1, 1945

Using Mineral Maps to Rank Potential Processing Behaviour

Sep 13, 2010

FROM time to time articles have appeared in the technical press on the interesting subject of surface combustion. The theoretical part of the problem has, for practical purposes, received ample consideration in those articles, but the number of practical applications of surface combustion referred to has generally been very small.It is the writer's object to review some recent developments in surface combustion, and also to try to arrive at an estimate of its advantages and possibilities. It is not necessary for this purpose to dilate upon the phenomenon of surface combustion itself. Many interesting things have been said on the subject by Pro£. W. A. Bone, of Leeds, to whose researches the recent developments are largely due. A few illustrations may make clear what is meant by surface combustion.Prof. Bone, in an experiment, took a platinum crucible, which he heated in the flame of a Meker-burner. Then he turned the gas off for a second, and, opening the stop-cock again, allowed the combustible mixture to impinge upon the crucible, thetemperature of which was still well below the ignition temperature of the gas. Although no flame was visible at this stage, it was soon clear that, nevertheless, the gas and air had continued to combine, as the crucible would attain a red heat after a few seconds.Another instance of surface combustion was shown by a Mr. Fletcher, in 1882. He placed an iron ball, weighing 3 lb., on a slab of fireclay, heated it for a few seconds with a blow-pipe, and blew the flame out, leaving the gas-mixture still...

Jan 1, 1915

The case study has identified and characterised additional subsidence arising from longwall mining above or under existing longwall goaf. It suggests that the magnitude, mechanisms and prediction methods for such additional subsidence are different between the two mining configurations. This paper presents a proposed method to predict maximum vertical subsidence due to longwall mining under existing longwall goaf. It suggests that, unless different results from further new cases become available, the findings presented in this article, including the aforementioned prediction method, be applicable to the majority of sites in New South Wales, where multi-seam longwall mining is to take place. This article also presents an important concept of 'overburden modification' due to multi-seam mining. A causal relationship between the above-mentioned additional subsidence and 'overburden modification' has been identified as a result of the case studies. Further investigations into the physical processes that cause such overburden modification will be fundamental to the understanding and management of multi-seam subsidence.

Nov 25, 2010

By M Vendrup, T C. Christensen, C Dube

The adsorptive and granulate forming MetClean™ process has been used at many locations in Northern Sweden, Norway, Denmark, France, Spain, Mongolia, Japan and Australia. It has been pilot tested and used in full scale treatment plants to remove metals from:mine watersleachate from solid waste in incineration flue gasleachate from fly ash damsleachate from landfill and waste ponds.The following paper provides details of pilot and plants tests on the effectiveness of MetClean™ in removing arsenic, antimony, barium, cadmium, copper, molybdenum, nickel, radium, uranium, vanadium and zinc. Results show that MetClean™ may reduce the concentration of these metals in treated effluent water to the one part per billion (ppb) range.The paper also finds that, for specific metals, the optimal adsorption condition depends on the:pH levelmolar relation between the specific targeted metal and the addition of iron (II) or manganese (II)type of oxidation agentssalinity levelpresence of other metals.The most effective pH level varies according to the targeted metal but falls within the pH 5 to pH 11 range. A compromise pH level may be set when more than one metal is targeted for removal at the same time and through only one process step. The removal efficiency of one or both metals may be affected by operating at a compromise rather than optimum pH level.The MetClean process generates non-hazardous solid waste. Waste can then be disposed of more easily than brine or sludge.CITATION:Christensen, T C, Vendrup, M and Dube, C, 2015. Pilot tests for heavy metals removal in mine water, in Proceedings MetPlant 2015, pp 404–415 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Factors leading to the necessity for some individual testwork in solving most specific hydraulic transportation problems are listed and a description is given of a method used in determining critical flow conditions. An outline is given of the basic theory of the purpose of the testwork, and a means of applying test results for varied pipeline diamet.er and material conditions follows. Engineering and economic factors are applied to the solution of a specific hydraulic transportation problem and the use of the test results in plant practice is illustrated. The advantages of connecting pumps in series in centralised pumping stations rather than individually along the pipeline are stressed. Some notes are added on the future possibilities and economies of post pump injection of solids into high pressure pipelines.THE HYDRAULIC TRANSPORTATION OF SANDSAs well as all the classical variables involved in a pipeline installation, one must consider, when solids are to be transported, the effects of such variables as:(i) Proportion of solids in the pulp.(ii) The average specific gravity of the pulp.(iii) Specific gravity of the solid material.(iv) Solid particle average sizing and possibly shape.(v) Solids particle grading.(vi) Pipeline diameter for effects other than classically hydraulic.(vii) Pipeline material.(viii) Fluid viscosity.(ix) Pump characteristics.(x) Abrasive or corrosive properties of the pulp.Not surprisingly, the application of published data to the hydraulic transportation of a specific material is difficult if not well nigh impossible. Most hydraulic transportation investigations also involve economic and site factors vary...

Jan 1, 1959

Laboratory scale equipment was developed to recover zinc as oxide fume from granulated lead blast furnace slag. The cyclone furnace process is characterised by high treatment rates combined with continuous and independent operation.Results were sufficiently encouraging to warrant pilot plant scale trials being undertaken.INTRODUCTIONSince granulation of lead blast furnace slag started at Port Pirie in 1921 the stockpile of this material has increased to nearly 5 million tons which averages 17·5 per cent zinc by weight. Although a number of processes for recovering the zinc have been examined, economic considerations indicate that a slag fuming process is likely to be most suitable.In the conventional slag fuming process zinc is extracted by injecting pulverized coal and air into a molten slag bath. By maintaining a suitable air to coal ratio the oxidised zinc contained in the slag is reduced to metal. Volatilization of the zinc is followed by reoxidation in the gaseous phase with the addition of further air above the bath. The zinc oxide fume so produced is collected by normal gas cleaning methods.By examination of the thermodynamics of this process Bell, Turner, and Peters (1955) determined the zinc oxide activity of the slag over the duration of the fuming cycle.A combination of high temperature and high carbon monoxide/carbon dioxide ratio was found necessary for rapid zinc elimination.Since melting of the slag is an essential step in the slag fuming process, only two treatment methods appeared possible at Port Pirie until recently...

Jan 1, 1964

By M Kozikowski

The primary purpose of these investigations is to determine dewatering requirements and likely impacts associated with mining operations. Standard aquifer testing techniques were carried out at multiple locations within the Ord Range near Pardoo, Western Australia. Aquifer properties of an oxidised haematite orebody were calculated from test pumping data conducted in five fully penetrating test bores. Hydraulic properties of the Ridley magnetite orebody were calculated based on short term constant rate pumping tests, and packer tests. Packer tests were conducted in undeveloped and uncased exploration holes and diamond core holes. The new data sheds light on the hydrogeological properties of this previously unexplored region of Western Australia.Aquifer testing procedures for each bore included a preliminary step test followed by a constant rate test. Recovery data were collected in each bore over a period of four to six hours. Prior to testing, background water levels and water samples were collected in a network of monitoring and exploration bores to establish baseline water levels, gradients and water quality. Water quality within the bedrock of the Ord Range varies from 2000 to 5500 mg/L TDS whereas water quality within the alluvial sequence of the De Grey River is highly variable (400 to 2500 mg/L TDS), but is predominantly brackish with some water of potable quality which is used to supply Port Hedland. Test pumping supports the conceptual hydrogeological model that consists of a pod like orebody (aquifer) surrounded by low permeability waste rock (BIF), with very weak hydraulic connection to the adjacent alluvial systems. Calculated hydraulic conductivity from test pumping data across Pardoo ranged from 0.01 to 59 m/d, depending on deposit tested.A groundwater model was used to simulate dewatering required in proposed pits and to estimate the impact of dewatering on the surrounding shallow alluvial aquifers. Test pumping and numerical groundwater flow modelling indicate the proposed below water table pits can be successfully dewatered utilising in pit dewatering production bores. Yields from individual dewatering bores will reduce with time due to the reduction in saturated aquifer thickness.Based on the numerical groundwater modelling and field investigations the likely impacts to the adjacent De Grey River alluvial aquifer system (within the Priority 1 De Grey River Water Reserve) resulting from mining and dewatering activities is considered minimal. Recalibration of the groundwater model will be undertaken once several months of dewatering data are available.The aim of this paper is to present a range of aquifer parameters derived through standard aquifer testing techniques for an area previously unexplored in terms of hydrogeological characteristics. It is the goal of the authors to provide this comparison data set for future work in similar geologic media.

Jan 1, 2009

Flotation of Composite Synthetic Particles

Sep 13, 2010

By D P. Sainsbury, B L. Sainsbury, A Vakili, H-D Paetzold, P Lourens

The cave propagation behaviour of a jointed rock mass is strongly governed by the unique nature of joints and discontinuities, together with the intact strength of rock bridges that make up the rock fabric. A discrete finite difference (DFD) modelling technique has been developed to allow for the detailed consideration of the rock mass structural fabric at many scales and through many different stress paths that can be used for complex mine-scale analysis. The DFD methodology uses interfaces to explicitly represent large-scale structures and ubiquitous joints embedded within the simulated rock mass matrix to characterise intermediate structures. Through simulated testing of DFD materials, properties such as strength anisotropy and scale effects can be obtained. This paper discusses the successful application of implementing a DFD modelling technique for the back-analysis of caving-induced subsidence behaviour of Lift 1 at the Palabora mine.CITATION:Sainsbury, D P, Sainsbury, B L, Paetzold, H-D, Lourens, P and Vakili, A, 2016. Caving-induced subsidence behaviour of Lift 1 at the Palabora block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 415–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By T van der Meer, A Salokannel, M Martikainen, L M. Nevatalo, J McCulloch

Water use and wastewater management is becoming a focus for many industries around Australia and the rest of the world. Good quality water is increasingly being recognised as a precious resource, and regulations on the bulk storage and discharge of waste streams is becoming more stringent in order to protect the environment, existing water reserves and the communities that use these resources. Components such as heavy metals, arsenic, cyanide, and sulfate from acid mine drainage are some that occur at mining and metallurgical processing sites. Removal of such components can allow safe re-use of these streams, reducing the new water requirements of the process, or else allowing acceptable discharge to the environment. Re-use or discharge of treated water eliminates or reduces the risk associated with storage of large volumes of contaminated water on site.Technologies where a contaminant is selectively precipitated and removed as a sludge are used for many of these treatments. Selection of the best treatment option for wastewater must depend on what is suitable to each site, and consider not only the nature of the contaminant, but also other aspects, including the location and situation of the site, local regulations, cost of reagents, the sensitivity of the local environment and waste sludge disposal options. To outline how an effective and economical solution can be designed and delivered, this paper will present a case study for the removal of arsenic from a site wastewater, from assessment of the problem, selection of suitable technology, design and implementation, to the benefits delivered to the site.CITATION:Salokannel, A, Nevatalo, L M, Martikainen, M, van der Meer, T and McCulloch, J, 2013. Technology selection for removal of contaminants from an industrial wastewater, in Proceedings MetPlant 2013 , pp 531-538 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By J D. St George

Flyrock is the unexpected and undesirable projection of rock fragments during detonation of a blast and managing this risk is becoming an increasing challenge as urban development encroach toward mineral extraction sites. The basic factors associated with flyrock are discussed in relation to geology, blast design and management. Published data of historical flyrock events are investigated and compared with local information on incidents. Good agreement was found between the data sets. A computer program of flyrock was developed using projectile motion based on launch velocity and angle, rock size, shape and density. This deterministic model was coupled with a probability model to simulate blast events. The impulse time ?t of the explosive pressure was taken as the stochastic variable to replace launch velocity. The variables were calibrated to replicate field data. A simulation was executed to demonstrate the capability of the approach to defining flyrock danger zones. For a simplistic situation it was identified that an appropriate distance to be cordoned off for the blast danger zone is a radius of 120 m in front of the blast and 65 m behind.

Jan 1, 2001

By A Brzovic, E Córdova

In an underground mine, different mining activities such as undercutting and cave progression generate redistribution in the present in situ stress field, and these changes are represented in the rock mass through induced seismicity.In order to study and analyse the induced seismicity generated in El Teniente, a block model was developed to account for the dissipated seismic energy through different areas of the mine from 1992 to 2015. More than 2.1 million seismic events were unified and classified in 3D in order to be used for the interpolations. The resultant model variables account for the accumulated energy releases in a monthly time resolution, and provide the ability to intersect different 3D entities with the stored information in the blocks, and estimate the energy evolution inside these entities.The generated model was used to analyse the geotechnical variables that determine the seismic response for the rock mass in the mine, such as geometry and direction of advance of the undercut fronts, lithological domains, and to study the ‘work’ the rock mass needed to go through in order to generate caving in areas with different stress settings.A specific area of the mine under high-stress conditions was analysed by studying the seismic energy associated with two subsidence caves interacting around the project, the modelled lithology. Using the same approach two adjacent projects are analysed to understand the released energy from the rock mass based on different stress and geotechnical settings for each project.CITATION:Córdova, E, Brzovic, A and González, R, 2016. Analysis of progressive seismicity and its correlation with geotechnical variables at the El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 835–844 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Moyle F. J

This paper describes an apparatus which was developed to study solid-vapour equilibria and presents results which were obtained during a study of the FeCI3-AlCI3-CI2 system. Analysis of the results showsthat fractional desublimation might offer a means of achieving a useful separation of the iron and aluminium chlorides produced by the chlorination of bauxite. The results, presented in the form of isothermal vapour pressure curves covering the range of temperature 160-200°C, support the earlier findings of Semenenko et al (Dokl Akad Nauk SSSR, 154: 42-43 (1964)) that the solid phase contains two terminal solid solutions.The equilibrium constant for the formation of the mixed dimer, FeAICI6, was approximately 4. The latent heat of sublimation of aluminium chloride varied from 18 to 26 kcal/mole AI2CI6 for solid compositionsfrom 0.9 to 0·5 mole fraction FeCls3.

Jan 1, 1979

Who Macraes Mining Company Limited is can be summed up by the following statements: +         We have been New Zealand's largest gold producer for seven years +         We have one of the lowest market capitalisation per reserve ounce of the gold producers in the  Australian Gold Index +         We have a resource finding cost of less than NZ$l0 per ounce +         We have a large land bank with proven reserves +         We have an Operating Cash Margin of approximately NZ$200 per ounce +         We have reduced our Dry Milled Tonne Cost by 34% since 1992   Our Mission is to continually grow our gold business, through maximising cashflow and focusing on our value drivers being: +         Increasing reserves +         Increasing cash operating margins +         Increasing production   The real challenge is the reduction of operating costs and the optimisation of revenue, particularly in the current gold price environment.   The Company has as at 31 December 1996 total mineral resources of 6.1 million ounces and reserves of 3.4 million ounces. This together with our current cash position of approximately NZ$15 million and strong hedging book of approximately 800,000 ounces places the Company on a sound financial footing whilst positioning itself to aggressively pursue its growth strategy when gold price and market conditions improve.

Jan 1, 1997