Search Documents

By Cyril Wells, Paul E. Busby, Donald P. Hart

EARLY workers in the field have established that the diffusion of nitrogen follows normal diffusion laws. Concentration-penetration data from layer analyses of reasonably pure iron specimens nitrided in an atmosphere of CO-NH, are given in the literature,' and were utilized to calculate diffusion constants for nitrogen. The diffusion of nitrogen in y-iron may be represented approximately by the equation D - 1.07x10-' e-:".'m'"'r The diflusion coefficients, D, given by this relation represent mean values, since carburization occurred simultaneously with nitriding. The rate of diffusion in a-iron has been determined from calculations based on data obtained by measuring the internal friction of samples at each of several frequencies and temperatures.' The expression for the diffusion of nitrogen in a-iron derived from these experiments is D= 1.4x10-1 e-it tudent Increasing carbon content decreases the diffusion of nitrogen in a-iron.3 Oxygen, either dissolved or combined, has been shown' to exert a marked influence on the diffusion of nitrogen from a nitriding atmosphere. D values increase rapidly with increasing amount of dissolved oxide in the metal, but diffusion is completely inhibited if preliminary oxidation has produced the slightest trace of iron oxide on the surface. Diffusion coefficients have also been calculated from permeability and solubility data,' but these values are of questionable accuracy since the boundary conditions assumed may not actually exist. Experimental Method The method selected for determining the diffusion coefficient of nitrogen in a-iron in the present investigation was the so-called fractional saturation method. This method consists of heating the specimen in an atmosphere of H2-NH8 mixtures of known composition for a predetermined time. Following this treatment, the specimen is analyzed for nitrogen; and the diffusion coefficient is calculated from a known relationship of the fractional saturation, time of diffusion, and dimensions of the specimen. This relation is based on a solution of Fick's second law and assumes that the surface of the specimen immediately reaches a given concentration which remains constant during the diffusion anneal. Tabular solutions are available4-5 and provide the relationship between fractional saturation and the quantity \/Dt /a, where D is the diffusion coefficient in cm2 per sec, t is the time of the diffusion anneal in seconds, and a, in the present experiments, is the half-thickness of the slab specimen in cm. The method is adequately discussed elsewhere.9-10 Material The material for this study consisted of 3/32 in. thick (0.24 cm) carbonyl iron plate. The major impurities in this iron are oxygen and carbon, which are readily removed by long time high temperature treatment in an atmosphere of purified hydrogen. In order to reduce the diffusion anneal time for saturation runs, some of this material was rolled to a thickness of 0.015 in. (0.038 cm) prior to the hydrogen treatment. Hydrogen treatments were carried out in a hydrogen-purified Armco iron tube heated in a global

Jan 1, 1957

By Gaudin. A. M., S. C. Sun

THIS paper presents the results of a study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresis1-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation [z = 47ruu(300)$ Kx] in which z is the zeta potential expressed in in volts, u the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas,6 The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mix-

Jan 1, 1946

By V. J. Sikora, W. J. McGuire

Several years ago, we used an electric analogue computer to study the effect of vertical fractures on the productivity of wells in expanding fluid-drive reservoirs. The results of this work were used both as a guide to research and as a basis for the design of actual fracturing operations. In 1958, Dyes, Kemp and Caudle' published portions of the data from this study. The results were released in 1959 to service companies for use in fracturing guides. The purpose of this note is to discuss the experimental conditions and assumptions which were made to derive the information which is already partially a matter of public record. ASSUMPTIONS This study applies to fractures which extend in a vertical plane symmetrically from the well. For simplicity, we chose to study the case of a well in a square drainage area with its fractures extending toward two of its nearest neighbors. We have assumed no migration of fluid across the boundary of this area. The quadrant shown in Fig. 1 models this system. We made the usual assumptions that the reservoir is homogeneous and isotropic, that the fluid is homogeneous and that production is effected by fluid-expansion drive. We also assumed that the fracture extends from top to bottom of the reservoir. Of more practical interest is our assumption that the fracture does not change the size of the drainage area. This premise is appropriate if all the wells in the reservoir are fractured in the same way. But where a single well is fractured, its drainage area may be enlarged at the expense of its neighbors. This could be of economic importance. The assumption that the fracture will not extend beyond the established drainage area of the well also limits the application of the results. Such long frac- tures will yield benefits in excess of those predicted here. When we assume homogeneity, we disregard the frequently observed zone of damage in the vicinity of the well. Where damage is severe, the benefits resulting from by-passing it will far exceed those predicted by this study. All comparisons were made of systems producing in the semi-steady state. By this we mean that equal volumes contributed equally to flow (pressure was dropping at a uniform rate throughout the system) when the rate of flow was observed. EXPERIMENTAL SET-UP We used the pool unit of an electric analyzer' in this study. The squase drainage system of a well was rep-

By R. L. Caldwell, E. E. Glenn, L. J. Norton, A. J. D. Straus, S. V. Holcomb, J. Zemanek

A new and unique logging tool, called the Borehole Televiewer (BHTV), has been developed to inspect boreholes and to evaluate formations. Even though geologists and engineers have had only about 3 years' experience with the BHTV, the thinking of many of them has been radically influenced by the fascinating and revealing "log-picture" recorded with the tool. The BHTV fills a need for a logging tool that can produce a direct and descriptive record of the physical properties of the borehole environment. Although primarily developed to evaluate fractured reservoirs, the BHTV has been used successfully to solve a variety of problems related to formation evaluation and borehole inspection. Geologists and petroleum engineers have been confounded for many years by the problems of locating and evaluating fractures. Interpretation of the usual resistivity, acoustic or radioactivity logs, as well as the analysis of cores, for evaluation of fractured reservoirs is extremely difficult and often not definitive. This is understandable since analysis of cores from fractured formations has reported variously: (a) low porosity, (b) no effective permeability, (c) lack of any matrix oil saturation and (d) oil stains on fracture planes as the only indications of potential production.14 In recent years acoustic amplitude logs have been introduced and used with varying degrees of success to locate fractures.8'9'11"13 Conventional amplitude logs at best give only qualitative answers where quantitative ones are desired. The logs reveal nothing of the orientation of the fractures. In addition to these logs, various types of cameras, television, and rubber impression packers have been used for borehole inspection. (See Appendix.) The BHTV logging tool supplies both the quantitative and the orientation answers about fractures. The borehole can be filled with any homogeneous, gas-free liquid such as fresh water, saturated brine, crude oil or drilling muds. This tool takes an "acoustic picture" of the borehole wall. The resulting log is a representation of the borehole wall as if it were split vertically and laid flat. The log is oriented with respect to magnetic north. Any physical changes in the borehole wall are seen as changes in picture intensity. In this way, fractures, deformation or pits are reflected on the log. Tool Description The fundamental parts of the BHTV are shown in Fig. 1. A piezoelectric transducer probes the borehole wall with bursts of acoustic energy. A flux-gate magnetometer senses the earth's magnetic field and provides the means for determining the orientation of the log. A motor rotates the transducer and mag-

Jan 1, 1970

By P. G. Hallof

Only recently has the term Induced Polarization found its way into geophysical literature. Schlumberger first mentioned the possible use of the induced polarization effect in one of his early papers. Later, induced polarization was the subject of several university theses, such as Seigel's at the University of Toronto and Bliel's at the Michigan School of Technology. In addition, a group at the New Mexico School of Mining and Technobgy has done work on induced polarization. There is very little to be found in print on the subject of induced polarization. Several papers have been presented at meetings, the 1958 AIME and SEG* conventions, for instance, on laboratory measurements of the effect and theoretical considerations useful in the interpretation of field results. This paper is the first attempt to present actual field results which show the usefulness of induced polarization as a prospecting technique. There are several phenomena that can cause polarization when electrical current is passed through the ground. In a paper presented at the 1958 SEG* meetings Professor T. R. Madden of M. I. T. demonstrated that only two of these gave rise to appreciable effects. The first is a result of the membrane and diffusion effects in a sandstone that contains appre- ciable amounts of clay minerals. The unbonded charges associated with the clay mineral forma material that passes positive and negative ions with different mobilities. When current is passed through such a system for some period of time, polarization results. The second phenomenon, which gives rise to very much larger polarization effects, is the one used in the new prospecting technique. These effects are a result of the blocking action or polarization of metallic or electronic conductors in a medium of ionic solution conduction. This electrochemical polarization, called "the over-voltage effect" by electro-chemists, occurs whenever electrical current is passed through a volume of rock which contains metallic minerals such as base metal sulphides. This polarization at metallic interfaces in ionic solutions depends upon the chemical energies necessary to allow the ions to continue the flow of current by giving up or receiving an electron from the metallic surfaces. The energy stored in this reaction isanalogous to that stored when a condenser is charged. If a d. c. current flowing through such a system is interrupted, the polarization can be detected as a small, decaying current that flows after the applied current is discontinued. The decaying potential measured is a result of the current flow caused by charges returning to their equilibrium positions from the positions they assumed under the applied potential field. Because of the polarization, there is an excess of change at each metallic interface. There is an alternate method of measurement of the induced polarization effect. The electrical

Jan 1, 1961

By J. B. Conway

RECENT studies of first-stage creep data have led to a special least-squares procedure for use in calculating the Andrade creep-equation constants. This procedure is easy to apply, uses only experimental data, and yields results which do not vary with the individual making the analysis. Taking logarithms of the Andrade equation I = lo(1 +ßl1/3)ekt leads to In l = In lo + In(1 + ßl1/3) + kt A residual can then be defined as the difference between the logarithm of an experimental length value and the logarithm of a calculated length value. Following the usual least-squares approach differentiation with respect to 10 and k of the expression for the sum of the squares of the residuals leads to two equations which cannot be solved directly for the three constants involved. However, values of ß can be assumed and corresponding values of lo and k can then be calculated. Then the sum of the squares of the residuals can be calculated. For a certain value of ß this sum will exhibit a minimum value to identify the least-squares values for ß, lo, and k. An illustration of the application of the above least-squares approach is obtained by employing the creep data for lead originally presented by Andrade' in the development of the one-third creep law. A plot of the sum of the squares of the residuals as a function of ß is shown in Fig. 1 along with the corresponding lo and k values. The minimum is seen to occur at ß = 0.0143 from which lo = 39.149 and k = 7.27 x 10-5. Based on these results the Andrade equation for these lead data is 1 = 39.149(1 + 0.0143 t1/3)e7.27 x 10-5t compared to the equation I = 39.13(1 + 0.01457/l/3)e6.95 X 10-5t developed by Andrade (calculation procedure not given but was probably a graphical solution). Calculating length values using the above equations and comparing with the experimental length values, residuals corresponding to the difference between experimental and calculated length values can be obtained. The sum of the squares of the residuals can then be calculated. For the case of the least-squares approach a value for this sum was found to be 2.37 x 10-3 compared to a value of 3.47 x 10" for the equation originally proposed by Andrade. In other words, while the constants proposed by Andrade provide an excellent fit for the lead data, a still better representation is afforded by applying the least-squares approach discussed above. A similar result was obtained for the lead data at 162oc.l The least-squares approach led to 1 = 9.866(1 + 0.0497 t1/3)el.011 x 10-2t compared to the equation I = 9.94(1 + 0.0433 l1/3)e1.06 X 10-2t given by Andrade. In this case, too, the sum of the squares of the residuals is slightly smaller for the equation based on the least-squares approach. It should be pointed out that a double trial and er-

Jan 1, 1965

By Victor L. Stevens

The Oso tunnel is one of three tunnels located on the San Juan-Chama Project in south-central Colorado. The purpose of the tunnel is to carry water from the upper San Juan watershed through the Continental Divide into the Rio Grande watershed. The Oso tunnel contract was awarded by the U.S. Bureau of Reclamation to a joint venture of Boyles Brothers Drilling Co., Gibbons & Reed Co., and Cimco in February 1966. The Oso tunnel is 26,660 ft long and has a rock section of 10 ft, 2 in. with a lined diameter of 8 ft circular. The main portion of the rock formation was in the Lewis shale. This formation is quite consistent in hardness and texture with exception of localized limestone concretions and sandy siltstone inclusions. The job was bid on the basis of using a James S. Robbins mole of the P221 series. The decision for using a mole was predicated on the geology and the experience of the same joint venture on the adjoining Azotea tunnel where a mole was successfully used. The Robbins P221 series mole is capable of cutting from 9 ft, 11 in. to a 10 ft, 7 in. diam without any major change. It is 40 ft long and weighs 60 tons. The cutting head has 22 disk-type cutters and one center pilot (standard 9 7/8 -in.) tricone bit. The head is powered by four 75 hp electric motors. Gripper pads at about the midway point on each side of the machine are pushed into the tunnel ribs and thrust-cylinders in front of each gripper apply pressure to the face as the head rotates. The regripping cycle is 3 ft and then the grippers are retracted and advanced. Each cutter on the perimeter of the head is followed by a bucket which scoops up the cut material, almost in the same manner as a water wheel, and dumps it into a conveyor situated along the top of the mole. The muck from the mole conveyor is dumped into a gantry-type conveyor. The gantry conveyor is 350 ft long and is pulled

Jan 1, 1970

By Ralph H. Sweetser

N Greenup and Carter counties, in the northeastern part of Kentucky, are the remains of many old charcoal furnaces built and operated during the period from 1818 to 1892. They were all included in what was called the Hanging Rock district. In the summer of 1930 I visited ten of these old blast furnaces, as follows:

Jan 1, 1931

By R. L. Fullman, J. W. Cahn

A method is derived for obtaining the distribution of sphere diameters and plate thicknesses (or pearlite spacings) from size distribution functions obtained along randomly oriented lines. The method described offers several advantages over existing methods. IT is often of interest to measure not only the average particle size but also the distribution in sizes of particles dispersed in an opaque material, such as an alloy. Particles of a single size will exhibit a range of apparent sizes on the plane of polish. If the sample contains a distribution of particle sizes, the distribution of observed sizes on the plane of polish is related to the distribution of actual particle sizes by an integral equation, For example, a distribution of sphere sizes, N(r),

Jan 1, 1957

Lead-zinc production in Canada accounted for 19% of the total value of metals and minerals produced in 1976, says Keith C. Hendrick, president of Noranda Sides Corp. Mine production of recoverable zinc w as 1. 158 million toils of 27.4% of free world production in 1976. Slab zinc pro¬duction was placed at 472,000 tons that year. Canadian mine production of recoverable lead was 247,000 tons or 10.6% of the free world production. Refined lead that year was at 177,000 tons.

Jan 11, 1977

By C. F. Lucks, W. D. Wood, H. W. Deem

Electrical ad thermal-conductivity measurements have been made on titanium and 6 titanium alloys. The following expression was derived for calculating thermal conductivity from electrical conductivity: K = 0.626 s T x 10-8 + 0.00497 where K = thermal conductivity, cal sec-1 cm-2 cm0C-1 s = electrical conductivity, ohm-]cm-1 T = temperature, deg Kelvin This expression gives calculated thermal conductivities that are not in error by more than 10 pct from the experimental values for A-55 titanium and the 6 alloys measured; namely, A-110AT, C-110M, C-130AM, Ti-6A1-4V, Ti-140A, and Ti-155A, which are representative of the presently available commercial a and a-ß titanium alloys. THERMAL conduction in a gas, liquid, or amorphous solid is accomplished by energy diffusion from molecule to molecule, a relatively slow process. For this reason, such materials have a low thermal conductivity. When a material is crystalline, there is in addition a heat transfer by a vibratory motion of the crystal lattice. It is the contribution of this lattice conduction that makes a crystal a much better conductor than a gas, liquid, or amorphous solid. Lattice conduction, however, does not account for the relatively enormous thermal conductivity of a metal. This is explained by the freedom of movement of valence electrons. These valence electrons drift in a metal in a direction toward a drop in electrical potential and, to a lesser degree, in the direction of a temperature drop in the metal. Since both the electrical and thermal conductivities of a metal depend upon the presence of free electrons, there should be some relatively simple relation between the two. Wiedemann and Franz in 1653 first discovered an approximate empirical relation between the electrical and thermal conductivities of metals at the same temperature. This ratio varies appreciably with temperature, and Lorenz later showed that by adding a temperature factor to the Wiedemann-Franz ratio the value of K/(s T) is constant, where K is the thermal conductivity, a the electrical conductivity, and T the absolute temperature. This Lorenz constant shows a greater variation for alloys than it does for pure metals, the ratio increasing slightly as the proportion of alloying elements increases. It has been found that a closer correlation between electrical conductivity and thermal conductivity can be obtained by means of an equation of the form K - A s T + B [1] where A and B are constants. In this equation the term AsT is the contribution of electronic conduction and B is the contribution of lattice conduction to the total thermal conductivity. EXPERIMENTAL MEASUREMENTS Electrical-resistivity and thermal-conductivity measurements on titanium and 6 titanium alloys serve as the basis for determining an equation of the K = AsT + B type for titanium alloys. Specimens—Table I shows nominal compositions of the 7 metals on which electrical and thermal conductivities were measured. The electrical and thermal-conductivity specimens for each alloy were taken from stock of the same heat and usually from adjacent sections of the same bar. All of the metals measured were in a mill-annealed condition. Methods—Electrical-resistivity measurements

Jan 1, 1959

CONTENTS PAGE BAIN, EDGAR C.-The Nature of Martensite. Discussed by Ancel St. John, Henry S. Rawdon, Jerome Alexander, Howard Scott 1 FEILD, ALEXANDER L.-Effect of Zirconium on Hot-rolling Properties of High-sulfur Steels and the Occurrence of Zirconium Sulfide. Discussed by Beram D. Saklatwalla, Bradley. Stoughton, Andrew M'Cance, George F. Comstock, Alexander L. Feild 12 SAUVEUR, ALBERT and KRIVOBOK, V. N.-Use of Sodium Picrate in Revealing Dendritic Segregation in Iron Alloys. Discussed by George F. Comstock, John H. Hall 17 KINNEY, C. L., JR.-Economic Significance of Metalloids in Basic Pig Iron in Basil Open-hearth Practice. Discussed by V. J. Pazzetti, George B. Waterhouse, C. L. Kinney, Jr 19 NEAD, J. H.-Absorption of Sulfur from Producer Gas in Open-hearth Furnaces.. Discussed by George B. Waterhouse, C. L. Kinney, Jr 26 PRIESTLY, WILLIAM J.-Effect on Steel of Variations in Rate of Cooling in Ingot Molds. Discussed by Emil Gathmann, Paul E. McKinney, George A. Dornin. 27 MONYPENNY, JOHN H. G.-Stainless Steel, with Particular Reference to the Milder Varieties (Stainless Iron). Discussed by P. A. E.-Armstrong, Beram D. Saklatwalla 33 ROYSTER, P. H., and JOSEPH, T. L.-Effect of Coke Combustibility on Stock Descent in Blast Furnaces. Discussed by Ralph H. Sweetser,. Richard Franchot, Sidney Cornell, T. L. Joseph 41 DAVIS, F. W., and BOLE, G. A.-Observations on Requirements of Refractories for Open Hearth. Discussed by C. L. Kinney, Jr., L. F. Reinartz, P. E. McKinney 46

Jan 5, 1924

By J. A. Retty

IN the Labrador iron fields two concessions, totaling nearly 24,000 square miles, have been staked out and commercial-grade deposits delineated. The Newfoundland-Labrador concession, owned by the Labrador Mining and Exploration Co. Ltd., is a 20,000-square-mile tract in the upper basins of the Hamilton and N askaupi Rivers which drain into Lake Melville. The New Quebec licensed area is 3900 square miles, owned by the Hollinger North Shore Exploration Co. Ltd., lying to the northwest of the northwestern part of the Labrador concession. It includes the upper basin of the Swampy Bay River and part of the upper basin of the Whale River, both of which drain into Ungava Bay. Both of the above-named companies are controlled by Hollinger Consolidated Gold Mines Ltd. with The M. A. Hanna Co., of Cleveland, holding a minority interest. When exploration was first undertaken in 1936, the only published map of the area was that prepared by A. P. Low in 1895. It showed only the main watercourses and gave only a rough, general idea of the geology. The numerous lakes of this vast area had to be first sketched and then mapped. Since then, extensive geological and topographical surveys have been conducted by the Labrador company, work which is normally done by Government branches. The object of the work was to examine the area and gradually eliminate unfavorable or less favorable prospecting ground. With this object in view, geological

Jan 1, 1948

By H. D. Outmans

A method has been developed for determining the relative water wet-tability (fraction of the surface wet by water) of porous media. This method involves the adsorption of methylene blue dye from an aqueous solution onto the solid surfaces of rock contacted by the injected dye solution. Experiments on Berea snndstone cores have shown that water-wet cores adsorb a large amount of dye from solution. In oil-wet cores, however, the injected aqueous dye solution is prevented from contacting the adsorptive surfuces by a film of oil and virtually no dye is adsorbed. This method was tested by experiments on mixtures of water-wet and oil-wet sand. Using the dye adsorption method, it was possible to determine quantitatively the fraction of water-wet and oil-wet sarzd in such mixtures. The dye adsorption test is readily applied to determinitrg the relative water wettability of fresh oilfield cores. The cores are not extracted before testing. Observed values of the wettability of field cores tested to date have varied from 100 to 6 per cent water wet. INTR OD UCTIO N Recent articles1 ' have emphasized the important role that wettability plays in almost all phases of reservoir rock behavior. It has been shown that wettability has a profound effect on the interstitial water saturation, residual oil saturation, capillary pressure, relative permeability, waterflood behavior, and resistivity index of oilfield cores. A quantitative investiga- tion of the effect of wettability on these core properties is severely handicapped by the lack of a simple technique for measuring the wettability of a porous medium. If such a technique were available, it would provide investigators with a means of gaining insight into the distribution of phases within a core. A number of qualitative methods of estimating wettability are known. These include contact angle measurements, flotation tests and studies of displacement pressure: imbibition7 and relative permeability data.' Using these tests, it is usually possible to classify a core as water-wet, oil-wet, or some intermediate degree of wettability. One recently proposed method involving measurement of nuclear magnetic relaxatione offers promise of determining quantitatively the fractional wettability of cores. The equipment is rather elaborate and necessary treatment of the cores before testing probably alters the natural wettability. This latter point also applies to most of the cited qualitative methods. This paper presents a new technique for determining water wettability of cores; it is based on measurements of the dye adsorption capacity of the core. This method has the advantage of requiring relatively simple equipment and involves minimum handling of the core before testing. It is important to distinguish between the various concepts of wettability referred to in the literature. The term "wetting" is defined by Bartell as that phenomenon which occurs when a solid and liquid phase come in contact in any manner so as to form a solid-liquid interface. A preferentially water-wet solid is defined by Jennings in terms of the advancing contact angle in the solid water-oil systems. Brown and Fatt regard fractional wettability as the fraction of the total surface area that is preferentially oil-wet or water-wet. However, none of these definitions adequately describes the type wettability measured by the dye test. This calls for the introduction of a new term, "relative water wettability", which we define as the fraction of the total surface area of a core contacted by injected water. DESCRIPTION OF METHOD The ability of a porous medium (especially the clays) to adsorb large quantities of surfactants, dyes, etc., is well known. It is reasonable to assume that a substance can be adsorbed from solution onto a solid surface only if the solution contacts the surface. In this connection Shapiro" has shown by experiments on silica gel that completely dry gel will adsorb methyl red dye from a benzene solution. On the other hand, if a film of water more than several molecules thick is present on the silica gel, the adsorption capacity of the gel for the dye is drastically reduced. Thus, a study of the dye adsorption capacity of cores should give some clue as to the fluid distribution on the surface of the core. TEST OF METHOD As a qualitative check on this theory, dye adsorption tests were run on similar Berea sandstone cores (Table 1, Cores 1-5). Cores saturated initially with water and flooded with 0.01 per cent aqueous methylene blue adsorbed 0.58 mg dye/gm of core. Similar cores saturated initially with water, driven to irreducible water with oil, and then flooded with the same dye solution also adsorbed 0.58 mg dye/gm of core. Another core, treated with a 5 per cent Dri-Film solution, dried and saturated with oil (Soltrol) adsorbed no dye when the dye solution was injected. These tests confirm

By N. A. Gokeen, M. Ohtani

EFFECT of elements on the solubility of carbon in liquid iron is useful in calculating and correlating a number of thermodynamic properties as shown elsewhere in detail.' Kitchener, Bockris, and spratt2, and later Turkdogan and Hancock3 have investigated the effect of sulfur on the solubility of carbon at various temperatures and concentrations. For any chosen sulfur concentration, the solubility of carbon reported by Kitchener et al. is considerably lower than that by Turkdogan and Hancock. It was therefore felt that a reinvestigation of this problem was necessary. EXPERIMENTAL METHOD An alloy of Fe-C-S .was prepared with electrolytic iron and ferrous sulfide melted by induction in a graphite crucible, 4 in. high 1 1/2 in. ID under a CO-atmosphere. The temperature, held at 1500" ± 5°C in all experiments, was measured with a Pt-Pt + 10 pct Rh thermocouple immersed into the melt. In order to assure saturation with carbon, the melt was stirred with a graphite rod. After approximately 1 hr at 1500 °C, a sample was obtained by sucking the melt into a silica tube, 4 mm ID. The sample was then analyzed for carbon and sulfur by usual methods. RESULTS The results are presented in Table I and plotted in Fig. 1 with the individual values of Turkdogan and Hancock.3 Scattering in the data is equivalent to 3 pct or less in carbon analysis. The broken line represents the empirical equation obtained by Kitchener et al. from their data. It is evident that the present data are in good agreement with those of the former investigators but in disagreement with the latter. The cause for this discrepancy cannot be readily offered since the experimental methods in the three investigations were nearly identical. Additional evidence corroborating the author's results may be presented in the following manner. The difference between the solubilities of carbon in the ternary Fe-C-X melt with a small concentration of any element X, and in the binary Fe-C melt is %?C = %CIII-%CII [1] where %?C is the change in solubility, and %CIII and %CII are the solubilities in the ternary and the binary systems respectively. The value of %Cii

Jan 1, 1961

By George Mixter

MINING, in contrast to manufacturing, deals with a wasting asset. That which is taken out of the ground is gone, the property is depleted to that extent, and will eventually become exhausted of profitable ore. So the life of a mining company is dependent upon the ability of its management to develop improved methods to permit extraction at a profit of the lower-grade ores which remain, to extend by intelligent exploration the limits of its known ore bodies, and to find and acquire new properties to take the place of those that, for one reason or another, are no longer operated. Its history is a story of constant change, of the working out of properties here and the acquisition and development of properties there, to maintain the vitality of the whole. It is a story of estimating with the tools and the knowledge available the location and extent of hidden ore bodies and of devising the means of extracting

Jan 1, 1948

By L. F. Pease, J. H. Brophy

A phase diagram for the Ta-Zr system is presented. The system is of the minimum-melting point type with the 0-zirconium phase decomposing monotectoidally at 785°C and 95.5 at. pct Zr. The minimum solidus temperature is 1875°C and the temperature of the top of the monotectoid loop is 1775°C. Techniques employed included X-ray diffraction and fluorescmce, electron microprobe analyses, diffusion couples, metallography, and melting-point measurements. Errors due to interstitial solutes and in melting observations are particularly common in this system, and their occurrence is discussed. SEVERAL versions of the Ta-Zr phase diagram have been reported in the literature.lm7 Williams et al.' report a diagram of the minimum-melting point type with a monotectoid reaction at 800°C and 12 wt pct Ta. The minimum in the solidus occurs at 1820°C and 25 wt pct Ta, while the top of the monotectoid gap is located at 1780°C and 80 wt pct Ta. The experimental techniques employed were metallography, electrical resistance variation with temperature, dilatometry, X-ray diffraction, and direct observation of melting by the technique of Pirani and ~lterthum.' Experience in the Nb-Zr phase diagram has shown that small changes in the interstitial content can cause large shifts in the positions of the phase boundaries. Small amounts of inter -stitials can cause similar changes in the Ta-Zr system and may be responsible for the wide variations in the phase diagrams previously reported.'-' The authors15 have found that alloys containing 0.75 wt pct 0 and 1.0 wt pct Ni with tantalum contents from 19 to 85 at. pct often contain a lamellar or cellular precipitate after annealing above 1400°C. This precipitate is very similar to that reported by pollack,12 Ralls," and Donlevy17 for the Ni-Zr system. In the present investigation, a wider variety of experimental techniques and improved alloy purity were applied to the resolution of errors in diagrams for this system as they now appear in the literature. New results have been obtained in the areas of alloy homogeneity and purity. Errors in the common techniques of direct melting observation in binary alloys have been demonstrated. In the commercially important high-tantalum region, the more accurate metallographic method of solidus determination has been employed. EXPERIMENTAL PROCEDURE Nominal analyses of the materials employed are given in Table I. The zirconium was low hafnium reactor grade iodide crystal bar, and the tantalum was in the form of high-purity sheet. Powders were impossible to use because of gas content. Alloys were melted on a water-cooled copper hearth, with a thoriated tungsten-tipped nonconsumable electrode in 2/3 atm of Zr "gettered" argon. Alloys were

Jan 1, 1963

By Edward W. Parker

(Toronto Meeting, July, 1907.) NOTE.-The material from which this paper has been prepared was collected for the U. S. Geological Survey Bulletin, Contributions to Economic Geology, 1906, and appears also, though in somewhat more extended form without illustrations, in that publication. ALTHOUGH the briquetting of coals and lignites has been carried on for many years in Europe, and has reached a particularly high state of development in France, Belgium, and Germany, it has made comparatively little progress in the United States. The causes for the backwardness of the United States in this regard are several, and first among them has been the abundant supply of cheap raw fuel with which the manufactured article has to compete. With our millions of acres of coal-productive territory, from which the product can in most cases be cheaply extracted, it has appeared in many districts more economical to waste the slack or culm, which con¬stitutes a considerable percentage -of the product, than to attempt to save it at the additional expense required for briquetting. It is for this reason that the view in all sections of the anthracite-region of Pennsylvania is marred by the unsightly culm-banks which encumber the ground, and that in some of the bituminous-districts one sees huge piles of unmarketable- slack allowed to burn up in order to get rid of them. When the coal is of a coking quality, or when the slack can be used for steaming-purposes, these losses are not sustained, but many thousands of tons of what might be converted into usable fuel have been wasted every year simply because of the increased expense involved in its preparation.

Sep 1, 1907

By Zay Jeffries

From the title of this chapter the reader could expect an attempt to outline the anticipated shape of things to come, mineralwise. We have no crystal ball and if we possessed one we could claim no expertness in its use. In the first place no one can tell the future status of man. No one has any way of knowing to what extent peace will prevail, nor to what extent changes may occur in national sovereignties or forms of government or in international relationships. So future man is an uncertainty. Nor can we predict new developments that may result in significant changes in man's status or in the mineral industry or both. If, for example, this chapter had been written in the middle 1930's, nearly everything that has happened since in the field of atomic energy would have been missed. Yet what a vast change this has made in the status of man! Also the changes in the mineral industry have been important. A writer would have been bold indeed had he prophesied that uranium would play such an important role. But we need not confine our foggy vision to the atomic energy field. The steep rise in the use of aluminum, titanium, and germanium reflects the unpredictable in what may be thought of as the more normal pursuits. This should not discourage one from using the past and currently observable trends as bases for limited predictions. To do this, however, it is desirable to make certain assumptions about man's status without even a pretense that these assumptions have a high probability of fulfillment: 1. Only minor changes will occur in the geographical boundaries of the nations of the world. 2. World War III will not take place in the near future. 3. As a consequence of (2), man will not destroy himself by wanton use of atomic weapons. 4. Disarmament will take place, if at all, gradually rather than all at one time. Under the above assumptions the world will enjoy a period of relative peace even though the status may be one of an armed truce. The assump-

Jan 1, 1959

US 4,190,436 - In the cyanide leaching of gold ore in tailing or ore dump piles, or gold ore in vats or on pads, the ore is agitated and oxygenated by introducing timed bursts of air, along with cyanide in a cyclic or regulated manner. The leach liquor is drained from the material by providing a continuous flow of air. Fines are homogenously mixed, thereby reducing channelling In the ore bed. Yield is improved and cyanide consumption lessened. R M. Hughes Feb. 26, 1980. 7 pp. (75-105). Filed. 12-20-77 (862,335).

Jan 1, 1982