Search Documents

By T. A. Wright

THE-Institute of Metals Division opened on Tuesday afternoon with Wheeler P. Davey as chairman and G. E. Edmunds as vice-chairman. Four papers were on the program, two being of a fundamental character. A paper on "Internal Surface in Minerals and Metals," by R. S. Dean and J. Roster, was presented by the latter; C. H. Gottschalk discussed coercive forces in powders. In answer to a question by the chairman. The author stated that he had not investigated [he temperature coefficient of resistance. A paper on "Recrystallization and Grain Growth in Cold Worked Polycrystalline Metals," by L. W. Eastwood, Arthur E. Bousu, 'and C. T. Eddy, was presented by Mr. Eastwood. A. great many quantitative data were given, with little reference to the theory. Theoretical considerations were discussed by Dr. Gottschalk, and C. A. Edwards of the University College of Wales, contributed very interesting comment on the relationship of size and critical strain. Dr. Edwards discussed the necessity of considering strain with time and temperature.

Jan 1, 1935

By Richard G. Warren, Michael M. Minor, Gayle J. Thomas

INTRODUCTION Los Alamos Scientific Laboratory (LASL) initiated its effort in the Hydrogeochemical and Stream Sediment Reconnaissance (HSSR), a part of the Department of Energy (DOE) National Uranium Resource Evaluation (NURE) program, in late 1975. Since that time, LASL has completed sampling of the Rocky Mountain states of New Mexico, Colorado, Wyoming, and Montana at a density of about one water or waterborne sediment sample per 10 km2 and has sampled about 85% of Alaska at a density of at least one per 25 km2. Analytical results for these samples are reported by National Topographic Map Series (NTMS) quadrangle. All collection and analytical procedures have been standardized from the outset (Sharp, 1977; Sharp and Aamodt, 1978). Until early 1979, only uranium results were reported for these samples; thereafter, results include analyses for at least 42 additional elements in the sediment samples. Each LASL HSSR report also includes a discussion of the relationship of these analytical data to known or possible uranium resources; more recently, these data have been re- examined for their relationship to resources for other metals (Beyth et al., 1980; 1980a). Analytical results for LASL HSSR sediment samples are both comprehensive, including 43 elements, and precise, allowing close inter-comparison of data between quadrangles. A recent HSSR study shows that elemental concentrations in sediment samples from the Dixon Entrance quadrangle in Alaska are insensitive to the choice of sieve size fraction and do not vary significantly between stream locations a few meters apart, except for extremely high elemental concentrations (Warren, et al., 1980). Elements that are particularly reproducible include thorium, hafnium, and the .ram earth elements. Fortunately, sensitivities for these elements, which are often associated with uranium, are excellent by the nondestructive analytical technique of neutron activation analysis that LASL employs. Wet chemical techniques may not always give reliable results for these elements in sediment samples due to the difficulty of dissolving the resistate mineral phases that normally contain these elements. LASL has recently open-filed results for a large number of NTK3 quadrangles; to date analyses have been reported for about 605 of the quadrangles within the states of the Rocky Mountain region. As a result, uranium analyses am now complete for all sediment samples collected from the state of Wyoming. We have chosen to sumnarize the analytical results for Wyoming and portions of adjoining states hereafter termed "the ~ Wyoming regionn (Fig. 1 ) ; nearly 24 000 uranium analyses and nearly 17 000 analyses for 42 additional elements are available for sediment samples collected from this area. The DOE open-file report numbers are shown in Fig. 1 for reports open filed before September 1, 1980. The Wyoming region provides an ideal area for an examination of regional geochemical patterns ex- hibited by sediment samples. It is endowed with a variety of exposed geologic units and with widely distributed uranium districts associated with host units of several ages. However, discussion will focus on rock units of Eocene and Precambrian ages because they are widely exposed and host the majority of the uranium resources within the region (Fig. 2). Miocene units are also widespread and host mineralization in the Brown's Park Formation (Fig. 2). Epigenetic uranium mineralization occurs in sand- stones of lower Eocene age such as the Wasatch, Battle Springs, and Wind River Formations whereas vein type mineralization occurs in Precambrian crystalline rocks. Precambrian rocks within the region consist of a variety of granitic and meta- morphic rocks with l .4-2.8 billion year ages, except within the Uinta Arch, where they consist of a sequence of very low grade metamorphosed or unmetamorphosed 1.0 billion year old sedimentary rocks. Precambrian rocks have served as sources for much of the clastic material comprising the lower Eocene units, and may also have provided the source for the uranium in mineralized Eocene or Miocene sandstones (Stuckless, 1979). The remainder of this paper describes the relationship of elemental concentrations in HSSR sediment samples to exposures of Eocene and Precambrian rocks. The results are used primarily to determine where these Precambrian rocks might provide the most suitable uranium source areas and to infer the direction of transport toward adjacent depositional basins during the Eocene.

Jan 1, 1980

By C. H. Keplinger

WARTIME factors have strengthened the production engineering consciousness of the petroleum industry. The basic principles of sound oil-production technology have been accepted as the standard by the industry and the governmental co-ordinating agencies. Every effort is being made to furnish larger quantities of petroleum with a minimum expenditure of materials and under strict conservation practices. The sphere of influence of production engineering extends from fundamental reservoir control of withdrawal rates and reservoir pressures to bolstering production from stripper wells. Serious transportation difficulties in moving oil to the East Coast have stimulated secondary recovery operations in the Appalachian and East Central oil-producing states. Diminishing discovery of new oil reserves by exploration activities increases the importance of promoting efficient oil-producing methods and practices throughout all productive areas in the United Nations.

Jan 1, 1943

By Carl R. Davis, J. L. Willey, S. E. T. Ewing

The first tube-mill on the Rand was put into operation in May. 1904, at the Glen Deep Mine. From that time onwards, tube-mills were added to various plants, although little was known regarding the capacity of a given tube-mill when working on banket ore. Within a few years, however, the so-called standard size (length of shell, 22 ft. 0 in.; diameter, 5 ft. 6 in.) was generally used until the last year or two. Practically the only exceptions were about 30 tube-mills having a length of 16 ft. and a diameter of 6 ft., and a few open-end mills of the roller-supported type. Most of the information obtained during the last 15 years has been obtained with mills of the standard dimensions. The adoption of the tube-mill as an accessory to the stamp mill was rapid; and where 3 tube-mills were working on the Rand at the end of 1904, 244 were in use seven years later.' By 1910, good practice provided 1 tube-mill for 20 stamps of 2000-lb. falling weight. The horsepower of the motors driving the tube-mills had increased from 80 to 100 and then to 125 at this date. Broadly speaking, current practice at that date aimed at a ha1 product of which 60 per cent. was suitable for sand treatment and 40 per cent. for slime. The sand grading was +60 mesh, 6 per cent.; +90 mesh, 25 per cent.; — 90 mesh, 69 per cent.; and the slime grading +200 mesh, 2 per cent.; —200 mesh, 98 per cent. It was recognized comparatively early that the tonnage of — 90-mesh product produced by a tube-mill per 24 hr. was a convenient measure of

Jan 1, 1925

By D. S. Flett, A. W. Fletcher

Equilibrium studies on the extraction of nickel and cobalt with kerosine solutions of naphthenic acid have shown that an exchange extraction reaction occurs at pH 5.5. The nickel/cobalt separation factor is constant at 1.8 for constant total metal molarity and varying nickel/cobalt ratios. The separation factor decreases with increasing total metal molarity in the organic phase beyond 0.2 M and also decreases with increasing temperature. From the equilibrium data, it has been possible to derive a mathematical model for the separation of nickel from cobalt by exchange extraction in multistage systems. Experimental data from a continuously operated multistage mixer/settler apparatus has shown a reasonable correspondence with computer-calculated data. The effective separation of nickel and cobalt in sulfate solution remains a problem in hydrometallurgy and the hope that this would be solved by solvent extraction has not yet been fulfilled. With chloride solutions, advantage may be taken of the ability of cobalt to form anionic complexes with the chloride ion. It can then be readily separated from nickel, which does not form stable chloro complexes, by extraction with a suitable long chain amine. However, in hydro metallurgical operations, sulfate solutions are generally obtained in which no extractable anionic species are present. Thus, the possibility of using cationic extractants must be considered, and in this paper attention is directed to the use of carboxylic acids. The method of separation studied has been termed exchange extraction, which involves replacement of a metal in the organic phase with a more acidic metal in the aqueous phase. Thus, (BR2).+ (Az+)aqt=(AR,).+ (B2+)aq (I) where metal A is more acidic than metal B, R represents the acidic radical derived from the acid RH, and the subscripts e and aq refer to the organic and aqueous phases, respectively. Ashbrook and Ritcey' have used this method for the separation of cobalt from nickel using the sodium salt of di-2 ethyl hexyl phosphoric acid, which preferentially extracts cobalt. Some nickel is coextracted, and this is removed by exchange with cobalt ions in the feed solution by suitable countercurrent operation in a pulsed column. Much work has been carried out by a number of workers in Russia on the general use of exchange extraction for the separation of metal ions using car-boxylic acids. Gindin et aL a have demonstrated that this technique could be applied to the separation of nickel from cobalt using a C--C. carboxylic acid and have applied the technique to the production of high purity cobalt solutions for electrolysis. Further worka was concerned with the development of a process for the separation of nickel from cobalt in a pulsed column. This system permitted the separation of iron and copper from nickel and cobalt in one system. The procedure involved center feeding with acid backwashing at the top and alkali addition lower down the column. Thus the system operated under a pH gradient and the metals were distributed in the column in the order of their basicities. A similar application was studied by Gel'perin et al,4,5 for the removal of copper and iron impurities from a nickel anolyte by means of a C10-C,12 fatty acid fraction. Ginden et al,' and Fletcher and Wilson' have studied the effect of pH on the extraction of a number of metals with carboxylic acids. These studies showed that metals such as iron, copper, lead, zinc, nickel cobalt, and manganese are extracted at pH values close to the pH of hydroxide precipitation. Nickel is extracted at a slightly lower pH than cobalt and thus the nickel/cobalt separation factor has a value not much greater than 1. More basic work on complex identification has been reported by Fletcher and Flett: by Tanaka; and Jay-cock and Jones." These studies have suggested that at low loadings in the organic phase, the nickel and cobalt carboxylates appear to be dimeric and solvated by free carboxylic acid molecules. As the concentration of metal in the organic phase increases, the complex changes and larger polymeric species are formed. In order to permit assessment of the potential of carboxylic acids as extraction reagents for separation of

Jan 1, 1971

By S. V. Krusiewski, J. W. Gabelman

Regional metallogenic zones and areas of equal paragenetic range have been interpreted from a compiled metallogenic map. of Mexico. Mineralization gradients of the pattern subsequently identified extend inland from coastal zones of high-temperature mineralization, and join in a central longitudinal zone of relatively low-temperature mineralization, apparently leaving no zonal room for lowest temperature deposits. The striking regional zoning pattern can be correlated with regional deformation gradients of similar position and orientation. The gradients represent at least three major orogenic cycles in two structural belts. Paleozoic structural belts existed along each coast with deformation gradients diminishing inland toward a narrow, central peninsular craton. The Mesozoic-Tertiary Mexican (Cordilleran) belt covered the entire country with a gradient oriented toward the Gulf of Mexico. Most ore deposits in this belt are of Tertiary age, although Tertiary mineralization gradients seem to have "inherited" the pattern left by Paleozoic tectonic gradients. Mineralization gradients can be used to identify the regions most favorable for the occurrence of selected metals. A metallogenic province is characterized by particular proportions of various metals, and the relative proportions can vary from province to province; but within any province the same intensity of mineralization would produce similar deposits in different places. Declining intensity of minetalization produces different kinds and sizes of deposits in zones that are concentrically arranged around sites of strongest rock alteration. On a regional basis, districts of similar average intensity of mineralization occur in zones that generally parallel some tectonic grain with the result that tectonic deformation has been designated a principal cause of mineralization. Variations in the type and intensity of deformation would determine the type as well as size of metal deposits. Mexico is especially favorable for such a study be- cause of its great abundance and variety of epi-genetic mineral deposits in various lithologic, structural and tectonic environments. The concept is also useful in recognizing portions of Mexico favorable for the occurrence of specific metals. METALLOTECTONIC ZONING IN MEXICO Theory: In studies of individual districts and groups of districts throughout North and South America, areal zoning of metal deposits generally seemed to respond to the paragenetic sequence of iron, gold, copper, zinc, lead, silver, antimony and arsenic, gold and fluorite. However, the definition of district zones is greatly obscured by contemporaneous or rhythmic deposition of metals, especially in the middle of the paragenetic range, and by the common superimposi-tions of different generations of metals. Zones could usually be distinguished only for groups of metals, such as early precious metals, base-metal sulfides, sulfosalts and late precious metals. The best defined zoning in a district is normally the spatial separation of the greatest volumes of altered and metallized rocks.' Exceptions are districts representing the high- and low-temperature extremes of the mineralization range where the former creates a matrix for the latter. In most districts the total quantity of alteration products is greatly in excess of, and appears to be roughly proportional to, the total quantity of metallization products. Subsequent to the bicomponent nature of each district, the most important mineralogical feature is the great excess of one to several metals or minerals which results in a district identifiable as one of predominantly gold, copper, lead-zinc, fluorite, etc., although a great variety of other elements may be present. The para-genetic range for the abundant elements in any district is only a portion of the entire possible range for all the elements representing the complete process throughout the region. Early during investigations of this type, it became apparent that the consistent bicomponent character of districts allows two methods for studying epi-genetic mineralization patterns. One is to identify and plot altered rock "pipes,"* which are easily recognizable in the landscape by their anomalous

Jan 1, 1969

By D. J. Weintritt, R. G. Hughes

Statistics show arz increase in the average depth of wells drilled in recent years. As a corollary to this trend, drilling fluids have been improved in an effort to meet the problems inherent at temperatures approaching 500°F. Of importance are (1) deterioration of mud components and (2) the effect of solids on filtration and rheological properties. High-temperature, stable water-base and oil-bare muds are discussed. Those areas in which differences exist are pointed out. Results are based on data taken from the Fann consistotneter, rheometer and shear-strength measurements, static and dynamic filtration tests, methy-lene blue test for bentonite solids and specific heat measLrrenlents of muds. INTRODUCTION Higher well temperatures go along with the fact that the average depth of wells continues to increase. Recent data by Gardner' lists 137 completions deeper than 15,000 ft for the first half of 1964 with a record second-half total of 167 wells drilling or proposed. In addition, there has been an increase in drilling for steam for power production or mineral recovery. In this application the depths are modest, but the mud may approach the critical pressure and temperature of water. Scearce and Magnon' report drilling mud used at temperatures of about 700°F in the Salton Sea area of California. Most deep wells have been drilled with water-base muds. In recent years, however, there has been a substantial increase in the use of oil-base muds because of technological advances in effective additives. The significance of this development was dealt with in considerable detail by Simpson and his co-workers.3 Additiona1 field data have now been obtained to indicate that oil muds are competitive in control, performance and cost with the best types of water muds for use at high temperaturc. This parallel offer of two very different fluid systems, each offering a similar variability in performance, cost and convenience, has created the need to evaluate the merits of these fluids under specified conditions so that the advantages and disadvantages of each can be weighed in relation to the over-all drilling program. This paper is not intended as a review of all the factors. Rather, it attempts to emphasize: (1) important condltions and facts peculiar to high-temperature drilling muds, (2) that more than one imposed test condition or testing method is necessary to describe the quality of a mud at high temperature and (3) that elaborate experimental precautions are necessary whenever laboratory data are used in selection of a mud for field use. WHAT IS A HIGH-TEMPERATURE DRILLING FLUID? For the purpose of this discussion, a high-temperature drilling fluid is any system so formulated or treated to economically minimize the effects of temperature on the properties of the fluid. Our experience in drilling fluids suggests that these effects become obvious for many mud materials at temperatures of 300F or higher. It is understood that hydrolysis of starches, depoly-merization of certain organic thinners, or irreversible chemical reactions (such as that of clay and lime) can affect filtration, viscosity and shear strength at less than 300F. However, the temperature level is not a serious point and in no way affects the precautions and techniques used in this study. An up-to-date review of the literature on high-temperature drilling fluids and the many variations was treated by Rogers'in 1963. EXPERIMENTAL REQUIREMENTS TESTING EQUIPMENT AND PROCEDURES With the advent of deeper drilling and increased demand for temperature-stable drilling fluids, new testing equipment and laboratory techniques were devised for the evaluation of drilling fluids subjected to elevated temperature and pressure. While the equipment has not been standardized, it is in widespread use. Milligan et al. Qescribe a filtration cell for determining the filtration properties of drilling fluids at temperatures in excess of 300F. They showed the effect of variations in temperature and pressure on oil and water muds filtered in the 300 to 400F range. The dynamic filtration apparatus described by Simpson6 permits the study of the filtration properties to temperatures of 350F for drilling fluids circulated over sandstone cores. Watkins et al.' describe the use of pressure bombs for studying the effect of prolonged periods of elevated temperature upon the gelation or solidification of drilling fluids. Chisholm et a1.' describe the use of a modified cement consistometer adapted for use in drilling fluid evaluations. A similar consistometer is used in this study, although the application and data-recording method have been changed. The consistency of a mud sample is measured by timing the movement of a soft iron bob which is magnetically moved up and down in the sample container.* Changer in the time of travel and the temperature of the mud at that moment are plotted with a two-point Brown Elec-tronik Recorder. A 10-in. chart with a speed of 4-in./hr is used. Fia.- 1 is a generalized internretation of the data ob-

Jan 1, 1966

By HENRY M. PARKS

THE total production of all metals in Oregon to date is estimated at $160,000,000; ~115,000,000 from eastern Oregon and $45,000,000 from the western part of the state. In 1916 the metal production of the state was approximately $4,000,000, while the present annual production has dwindled to a little less than $1,000,000. Western Oregon The state of Oregon contains several metal-bearing areas, widely scattered in different regions. More than half of its coast is fringed with a belt of auriferous sands which sometimes are rich in fine gold. A second mining field, the chief producing one of western Oregon, is situated in the southwestern part of the, state and includes Jackson, Josephine, Douglas, Coos and Curry counties. It may be considered as the northern extension of the gold and copper belt of California. A third region in western Oregon is that on the western slope of the great Cascade range in the Bohemia, Blue River, Quartzville, North Santiam and Ogle Creek districts-from the Siskiyous on the south almost to the base of Mt. Hood near the Columbia River on the north.

Jan 1, 1925

Jan 1, 1888

By C. C. Miller, A. B. Dyes

The cost of finding and developing new reserves is continually rising. We must meet these rising costs with more economical operations. This can he accomplished if we revise our ideas of proper well spacing and well allowable to consider the concept of optimum well spacing. According to this concept, the optimum spacing is the one which leads to the maximum present worth for a reservoir when ail factors affecting total cost and total revenue are considered and when the wells are produced in the most eficient manner. Application of this principle efficiently utilizes available well potential and properly considers the recovery eficiency in addition to fixing the spacing on the basis of the amount and value of the oil to he recovered. This Study presents an analysis of one producing zone containing low gravity crude to illustrate the effect of these factors on the present worth and on the optimum economic spacing under two production drives—-evolved gas and water drive. The maximum present worth occurs when the optimum number of wells for open-flow operation is employed. Frequently, this optimum development cal1s for very wide spacing and the ideal field rates are not unreasonable. Under other circumstance. where proration is necessary, an optimum combination of well spacing and well allowable exists which permits production at relatively high rates. The optimum well density in a field depends on the recovery efficiency and the valule of the oil. In solution gas-driven reservoirs this optimum spacing for operation at high producing rates can vary from extremely wide spacing to handle viscous low gravity oil in thin formations to relatively close spacing in thick sands where good recoveries are expected. Because of the better recovery from water-driven fields, the optimum spacing in these fields is closer than in solution gas-driven fields. Also, the water encroachment pattern is dependent upon the well spacing, and an adequate numher of wells is needed to assure a good sweep eficiency. The economic optimum well density in a water-driven field is high enough for this purpose. INTRODUCTION From year to year domestic oil becomes more difficult to find. The fields we do locate are frequently smaller and deeper than older fields and the costs for men, material and equipment are continually rising. To replenish our reserves we must continue to search for and develop new fields, but experience has shown we cannot expect prices to rise in proportion to costs. Consequently, we must meet increasing costs by more economical operations. A vigorous effort is being made within the industry to improve exploration methods, to cope with the problems of deeper drilling, and to obtain a secondary yield from older fields. Many significant contributions have resulted from these efforts. The economic operation of new fields can be further improved by developing these fields on optimum spacing and producing the wells at higher rates. This would avoid the drilling of unnecessary wells and provide additional capital for seeking new oil. While the benefits of these practices are obvious, the problem of defining the optimum development of a field for natural depletion can become very complex. A study of the effect of well spacing and several reservoir variables on economic worth of a specific field is reported here to illustrate the problem and to show the magnitude of the benefits to be realized. This study is necessarily limited to the field conditions selected and is not intended as a general solution of the well spacing problem. It does, however, indicate factors to be considered, the trends to be expected, and the direction in which we should proceed in developing new fields. NO consideration is given to land and legal considerations which might arise. METHOD OF ANALYSIS The optimum method of developing and producing a field is to use the combination of spacing and prora-tion which gives the maximum return. In addition, we do not want to lose recovery. These considerations of maximum return and maximum recovery present no serious conflict. The value of each method of operation is conveniently expressed in terms of its present worth. According to the present worth method of evaluation,' an acceptable annual percentage return is assigned to the operation, and all incomes, capital costs, and expenses are discounted at this rate to the start of the operation. This net value is the present worth. If we apply the same discount rate to several alternate methods of operation, the one yielding the greatest present worth is the best method. If we express net income in terms of price per barrel of oil produced, drilling and equipment costs on a well basis, and expenses as cost per well year, this evalu-

By Stanford O. Grodd

The Sanford Lake district encompasses an area covering 24 square miles in the central Adirondack Mountains of northern New York State. Discovery of the titaniferous magnetite deposits dates back to 1826. Several attempts to exploit the ores for iron prior to 1942 proved uneconomical because of difficulties with the associated titanium, lack of transportation facilities, and the isolated location. Since 1942, the National Lead Company has produced ilmenite concentrates for the titanium pigment industry, and a magnetite by-product used in the steel and refractory industries. Rocks of the area are Precambrian in age and of igneous origin. The area has a history of erosion, deformation, and metamorphism, subsidence, and finally uplift and glaciation. The resulting topography is extremely rough with drainage patterns controlled by a combination of fault patterns and glacial modifications. The district is within the large anorthosite massif making up the central high peak area of the Adirondacks. All of the various lowsilica rock types associated with the massif are found within the boundaries of the district. These consist of both the Marcy and Whiteface types of anorthosite and of gabbroic anorthosite, gabbro, and different grades of titaniferous magnetite ores. All of the rocks contain the same minerals and differ only in their percentages of these consitituents. Gabbro, and ore associated with it, demonstrate flow structure as both have foliation and lineation. Anorthosite and its associated ores are massive and show very little primary structure. Minor pegmatites and diabase dikes provide evidence of remobilization in selected areas and of late intrusion as well. Faulting is prevalent and follows a regional pattern of major faults trending northeastsouthwest and of minor faults at nearly right angles to them. There are four mineralized areas where an economic grade of ore has been found. Three of these have both gabbroic-type ore and anorthositic-type ore. The fourth has only gabbroic ore. Ores are graded according to their TiO, content, and these range from 9.5 per cent to over 30.0 per cent TiO,. Ore bodies of both types are related to gabbro and conform to the configuration of the gabbro bodies within the anorthosite. At least three distinct theories of ore genesis have been expounded by different investigators. Others propose some variations of one or more of these. Although complete agreement probably never will be reached, it is certain that no one process of ore emplacement can explain the complicated picture as seen today. Further understanding of the ores and their origin will require detailed mapping, sampling, and mineralogical studies of the entire district, and then it may never be understood without qualification.

Jan 1, 1968

[ ]

Jan 1, 1938

By S. F. Emmons

Br far the greater number of the members of this Institute are men who are engaged in the strenuous work of the technical part of their profession, and find little time for the abstract scientific work which is less distinctly practical and pecuniarily emunerative. There is, however, a small but increasingly numerous class whose members devote themselves to broad geological problems which underlie the systematic development, and whose work, theoretically, ought to precede and form a basis of that of their more practical brethren. These are the so-called mining or economic geologists, who are, for the most part, connected with State or National geological surveys. From the character of their work, the life of these men necessarily follows rather different line's than that of most of their colleagues, and is not generally familiar to them. It seems admissible, therefore, that to the life of a prominent member of this class, who died during the past year, having literally sacrified his life to his work, a more extended notice should be given than the relatively small number of his contributions to the Transactions might seem to justify. George Romans Eldridge, son of Ellery and Sarah (Mathews) Eldridge, was born on Cape Cod at Yarmouth, Mass., Christmas day, 1854. His boyhood education in the public school at Yarmouth was followed by a six years' course in the Public Latin School at Boston, from which lie entered Harvard Uni¬versity in 1872, being graduated with the highest rank in his class in the natural sciences in 1876. During his college course he spent the summers of 1875-6 at Cumberland Gap, Ky., as volunteer aid to Prof. N. S. Shaler, who was then in charge of the State Geological Survey of Ken¬tucky. This vacation work, undertaken by him rather as a pastime, gave him his first leaning toward geology. Soon

Mar 1, 1906

By Thomas Leonard Watson

I. HISTORICAL. BARITE has been mined for many years in various parts of Virginia, probably the earliest mining-operations being in Prince William county, within 600 ft. of the Fauquier county line, about 4 miles south of east from Catlett, a station on the Southern Railway. It is claimed that the mineral was mined here as early as 1845. Mining-operations in Campbell and Pittsylvania counties in the Piedmont region, and near Marion in Smyth county, in the southwest Virginia Valley region, were begun about 30 years ago. The mining and milling of barite on a commercial scale in Tazewell and Russell counties are more recent, and commenced about 15 years ago. II. GEOGRAPHICAL AND GEOLOGICAL DISTRIBUTION. Barite occurs in many counties in the State, as shown in Fig. 1, but the industry has been confined to only a few of them. Its occurrence is noted in two of the three major divisions of the State-namely, the Piedmont region east of the Blue Ridge, and the Paleozoic area west of the Blue Ridge. In the Piedmont region the mineral has been mined in the following counties:, Bedford, Campbell, Louisa, Prince William, and Pittsylvania. In the region west of the Blue Ridge, composed of Paleozoic sediments, barite has been mined in Montgomery, Russell, Smyth, and Tazewell counties. Of the counties mentioned, Bedford, Campbell, and Pittsylvania of the Piedmont region, and Russell, Smyth, and Tazewell of the Valley region, have been the principal producers. In 1906, operations were confined to five counties-Bedford, Louisa, Pittsylvania, Russell, and Tazewell-but in the first two counties named there was no production, the work being solely development.

Jan 9, 1907

By K. H. Kilgren

At high formation pressures the distillate produced from a gas-condensate reservoir may be black in color. In this event the dense gas phase existing above the dew point is correspondingly dark. Volumetric phase data and an analysis of a reservoir fluid exhibiting these characteristics, together with a description of the visual equilibrium cell in which these observations were made, are presented in this paper. INTRODUCTION Previously the author, like many others in the oil and gas industry perhaps, tacitly assumed that the expressions black or dark oil system, crude oil system and bubble-point system were synonymous. Crude oil reservoir fluids are bubble-point systems and yield a black or dark stock-tank oil of relatively low API gravity. Conversely, a clear or amber colored trap distillate of high API gravity is assumed indicative of a dew point system or a gas-condensate reservoir fluid. This broad classification appears satisfactory for shallow reservoirs, but as the following study demonstrates, may be misleading when applied to deep reservoirs. Theoretically, there is no reason to exclude the possibility of producing a dark, low-gravity distillate from a gas-condensate reservoir. At sufficiently high values of pressure and temperature, heavy, dark-colored hydrocarbons may exist in the vapor state of a multi-component system. If enough dark-colored components are present in the reservoir vapor phase, the resulting condensate will be dark. The reservoir fluid investigated in the present study supports this contention. Stock-tank production was black in color and measured 29" APT gravity. From outward appearances, the liquid closely resembled a medium gravity crude oil. Experimental measurements proved the reservoir fluid was in reality a gas-condensate system. Volumetric phase data for this high-pressure system and a description of the visual cell in which the study was conducted successfully are presented in this paper. THEORY Phase behavior of a reservoir fluid can be predicted accurately with reference to a pressure-temperature phase diagram. If the reservoir temperature is lower than the critical temperature of the hydrocarbon fluid in place, bubble-point behavior will be observed. If the reservoir temperature lies between the critical and cricondentherm temperature, dew point behavior and retrograde condensation will occur. For reservoir temperatures above the cri- condentherm, only a single gas phase can exist in the reservoir regardless of pressure. Providing the composition of the reservoir fluid were known, it would be possible to predict the critical temperature and estimate the phase behavior from equilibrium relationships. However, the usual practice is to obtain a sample of reservoir fluid, subject it to varying pressures at the reservoir temperature and observe the phase behavior experimentally. The latter method was used to obtain the data reported here. WELL AND TRAPPING INFORMATION A summary of pertinent data for the well from which the reservoir fluid was sampled is presented in Table 1. This well is located offshore Louisiana. Except for the pressure which substantially exceeds hydrostatic pressure, the information does not appear unusual. Prior to the sampling program, the well was produced for 22 hours at a stock tank oil rate of 139 B/D. Average trapping conditions and gauging data for the six-hour test period that followed are summarized in Table 2. Samples of the first-stage trap gas and liquid were obtained during the latter portion of the test period. Ambient temperature remained 5 to 10F below trap temperature and presented no problem for sampling. Surface wind and moderate foaming of stock-tank oil presented some difficulty in obtaining accurate stock-tank gauges. SAMPLE ANALYSIS Compositions of the gas and liquid samples are shown in Table 3. The trap gas was analyzed by isothermal chromatography which revealed only a trace of heptane in the stream. The trap liquid was initially analyzed by low-temperature fractional distillation, yielding a bottom product of heptane and heavier components. Specific gravity of this fraction was measured and the mol weight was determined by freezing point depression. The hexane and lighter overhead gas collected during distillation was

Jan 1, 1967

By C. S. Blair

The development of a geological department as an integral part of the Tennessee Coal, Iron & Railroad Co. in the Birmingham district, Alabama, in 1908 was an innovation probably unique for any mining organization south of the Ohio River. At that time a few of the oil companies were starting geological departments, but there were no geologists among the larger industrial organizations. The Tennessee Coal, Iron & Railroad Co. had been a substantial producer of pig iron for many years and was just getting a start in the manufacture of steel products from the pig iron. It had large acreages of coal land, ore land and timber land, but there was lacking the detailed knowledge of the possible mineral resources of much of its territory, and this territory at that time covered an area in the neighborhood of 500,000 acres in the states of Alabama, Tennessee and Georgia. Those responsible for the operations of the mining properties, not being familiar with the kind of help that might be expected from geologic work, were decidedly skeptical of the utility of the work. Therefore it was necessary to develop cooperation with the mining organization, by not infringing upon its functions, and by developing the work in such a manner as to demonstrate to the mining department its practical utility. In the first instance the man responsible for a mining operation is apt to assume the attitude that the geologist is a blockader, because the geologist, unfortunately, is obliged to point out difficulties in the carrying out of mining operations in the way originally planned. He points out the dangers of mining out one coal or metal seam at the ultimate expense of an upper or lower seam, and he develops structural features, such as faults and folds, which call to the attention of the mining operator difficulties in his future operations, which the latter had not anticipated. Eventually, however, the value of having these data became apparent to the Tennessee Coal, Iron and Railroad Co., and the operators not only welcomed the geological work and cooperated fully in its acquisition of essential information, but reached the point of asking assistance and advice; and complete coordination of the two activities has existed for many years.

Jan 1, 1935

By C. S. Blair

The development of a geological department as an integral part of the Tennessee Coal, Iron & Railroad Co. in the Birmingham district, Alabama, in 1908 was an innovation probably unique for any mining organization south of the Ohio River. At that time a few of the oil companies were starting geological departments, but there were no geologists among the larger industrial organizations. The Tennessee Coal, Iron & Railroad Co. had been a substantial producer of pig iron for many years and was just getting a start in the manufacture of steel products from the pig iron. It had large acreages of coal land, ore land and timber land, but there was lacking the detailed knowledge of the possible mineral resources of much of its territory, and this territory at that time covered an area in the neighborhood of 500,000 acres in the states of Alabama, Tennessee and Georgia. Those responsible for the operations of the mining properties, not being familiar with the kind of help that might be expected from geologic work, were decidedly skeptical of the utility of the work. Therefore it was necessary to develop cooperation with the mining organization, by not infringing upon its functions, and by developing the work in such a manner as to demonstrate to the mining department its practical utility. In the first instance the man responsible for a mining operation is apt to assume the attitude that the geologist is a blockader, because the geologist, unfortunately, is obliged to point out difficulties in the carrying out of mining operations in the way originally planned. He points out the dangers of mining out one coal or metal seam at the ultimate expense of an upper or lower seam, and he develops structural features, such as faults and folds, which call to the attention of the mining operator difficulties in his future operations, which the latter had not anticipated. Eventually, however, the value of having these data became apparent to the Tennessee Coal, Iron and Railroad Co., and the operators not only welcomed the geological work and cooperated fully in its acquisition of essential information, but reached the point of asking assistance and advice; and complete coordination of the two activities has existed for many years.

Jan 1, 1935

THE Geophysics Education Committee has devoted several years to a consideration of the problem of training geophysicists. Past reports have dealt largely with fact finding and with the discussion of particular aspects of geophysical education. In the present report it is proposed to review the subject more comprehensively. This involves the question of what educational qualifications the geophysicist of the highest professional standards should possess, and the related question of what changes must be effected in existing educational institutions in order that prospective professional geophysicists may obtain instruction of the desired quality. The type of geophysicist here contemplated is one familiar with what is known already in the several branches of earth physics, and capable not only of following contemporary progress in any of these branches, but of contributing to that progress in a research capacity. Geophysics in its broadest sense, as has been emphasized repeatedly by this Committee, is the study of the physics of the earth and of terrestrial processes. This includes both the static and the dynamic characteristics of the gaseous, the liquid, and the solid portions of the earth, as well as its gravitational, thermal, and magnetic and electrical manifestations. Some branches of earth physics have been cultivated but slightly; others have reached an advanced state of development. Those branches whose development is sufficient to warrant explicit recognition in the form of organized Sections of the American Geophysical Union are: geodesy, seismology, tectonophysics, and volcanology, dealing with the rock constituents of the earth; oceanography and hydrology with the aqueous constituents; meteorology with the atmospheric constituents; and terrestrial electricity and magnetism with the electromagnetic manifestations. At present, instruction on the professional level in any of these branches of earth physics can be obtained in but few universities in North America. In most institutions where such instruction is undertaken different subjects are given in different and independent departments. Geodesy and hydrology are taught, if at all, as a part of civil engineering. The nearest approach to volcanology and tectonophysics ordinarily is represented by petrology and structural geology given

Jan 1, 1944

By S. O. ANDROS

RECORDS in mining operations naturally fall when improved equipment and methods are developed. And tunneling through the Continental Divide is a mining operation, even though the tunnel was not driven to strike a vein at depth. Although many engineering feats have been successfully accomplished in the development of water supplies in the Western States, the Twin Lakes Tunnel in Colorado presents some unusual features that make it noteworthy. To begin with, it is the first trans-mountain water diversion project in the West. The fact that the Continental Divide intervenes between where the water is and where it is needed was brushed, aside as of minor importance. It was enough to know that on the western side of Independence Pass, the highest in Colorado, with an elevation of 12,095 ft., there was water which was needed on the eastern side, where the Twin Lakes are situated, forming the

Jan 1, 1934