Search Documents

By Charles Maier

PART I DENSITY AND ENERGY CHANGES IN COLD-WORKED COPPER IT has long been supposed that when crystalline materials are com-minuted the energy used in the production of increasingly smaller grain sizes is not entirely dissipated as heat but that a certain portion is "stored" as a part of the internal energy of the material. This portion usually has been called the "surface energy" of the particles. The practical interest of the Bureau of Mines in this subject in connection with the energy requirements of crushing processes has led' to the author's attempt to measure the "stored" energy in finely divided calcite by heat-of-solution methods1. The experiments on calcite showed that "storage" of energy could not be proved for this material, because fine grinding caused a lack of chem-ical homogeneity evidenced by loss of carbon dioxide and subsequent adsorption of water on the surfaces of the calcite particles. When thermochemical correction was made for composition changes the cor-rected heat of solution was less for fine material than for coarse. Con-tinuation of the experimental work into the problem of comparing work and heat in the deformation of metallic crystals, where the calorimetric difficulties were less, showed, however, that in the case of copper and aluminum a real discrepancy between work and heat could be shown. Similar results had previously been obtained by Farren and Taylor2 and Hort3 and more or less simultaneously with the author's work by

Jan 1, 1936

By Robert H. Hafner, Irvin R. Kramer

IN recent years considerable interest has been shown in surface-alloyed metals, particularly those of chromium (chromized steels), which have excellent corrosion [ ] resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high temperatures of 1200° to 1400°C. (2200° to 2550°°F,) caused excessive grain growth and warpage, Louenstein and Ulmer2 packed iron castings in ferrochromium and com- [ ] mon salt, and heated for approximately three hours at 930° to 1040°C. (1700° to 1900°F,). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900° to 1000°C., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a chromized layer, 0.004 in, thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1942

By Robert H. Hafner, Irvin R. Kramer

IN recent years considerable interest has been shown in surface-alloyed metals, particularly those of chromium (chromized steels), which have excellent corrosion [ ] resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method' employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high temperatures of 1200° to 1400°C. (2200° to 2550 F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- [ ] mon salt, and heated for approximately three hours at 930° to 1040°C. (1700° to 1900°F.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900° to 1000°C., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1942

By E. V. Watts

The D-7 zone of the Ventura Avenue field is of special interest because the initial reservoir pressure at 92.00 ft nearly equaled the pressure exerted by the overburden. While the phenomenon has been observed elsewhere in the world, there is no record of a previous case in California. Such high pressures have been attributed to sealing of the reservoir, followed either by emergence of the beds or by compaction of the sediments in various ways. Oil in the D-7 zone is undersaturated. At pressures above the bubble point, oil is recovered by the slight expansibility of the reservoir framework and its liquid contents. More than 40 pct as much oil probably will be recovered by this mechanism as will be recovered by internal gas drive after pressures pass below the bubble point. Operations are handicapped by sand and pipe troubles. Introduction The Ventura Avenue field has been under development since 1915. It has long been considered a "high-pressure" field, but interest was heightened by the extreme conditions encountered in the recent development of the so-called D-7 zone. The original reservoir pressure in this pool is estimated to have been 8300 psi at a depth of 9000 ft below sea level, or 9200± ft below the surface. A fluid pressure approaching that exerted by the overlying sediments has been encountered in other parts of the world, but never before in California to the degree observed in the D-7 pool. With few exceptions, the original pressure in California fields is about equivalent to the static head of water below the water table in the outcrop. Structure The Ventura anticline is a prominent feature of the Ventura basin, being traceable on the surface about 17 miles.' The Ventura Avenue field is at the apex of the anticline. It is about one mile wide and five miles long, the major axis lying in an east-west direction. The productive limits cover an area of about 2300 acres. The entire anticline has been severely folded and faulted. The productive portions in particular are broken up by three major thrust faults having a general east-west strike. The resultant four fault blocks are termed the A, B, C, and D blocks, respectively. Certain electric-log intervals are assigned numbers. Fig I is a diagrammatic north-south section of the field near the crest, looking west, and shows three of the four fault blocks. To the west, the upper fault divides into two branches, which define the B block. Wells penetrating a fault may duplicate over 1000 ft of formation. However, the greater fault movement is the strike shift, which is believed to exceed 2500 ft both between the A and C blocks and between the C and D blocks. The location of water is irregular and unpredictable. A few intermediate waters exist, while some strata have more than 2000 ft of productive closure.

Jan 1, 1948

By E. V. Watts

The D-7 zone of the Ventura Avenue field is of special interest because the initial reservoir pressure at 92.00 ft nearly equaled the pressure exerted by the overburden. While the phenomenon has been observed elsewhere in the world, there is no record of a previous case in California. Such high pressures have been attributed to sealing of the reservoir, followed either by emergence of the beds or by compaction of the sediments in various ways. Oil in the D-7 zone is undersaturated. At pressures above the bubble point, oil is recovered by the slight expansibility of the reservoir framework and its liquid contents. More than 40 pct as much oil probably will be recovered by this mechanism as will be recovered by internal gas drive after pressures pass below the bubble point. Operations are handicapped by sand and pipe troubles. Introduction The Ventura Avenue field has been under development since 1915. It has long been considered a "high-pressure" field, but interest was heightened by the extreme conditions encountered in the recent development of the so-called D-7 zone. The original reservoir pressure in this pool is estimated to have been 8300 psi at a depth of 9000 ft below sea level, or 9200± ft below the surface. A fluid pressure approaching that exerted by the overlying sediments has been encountered in other parts of the world, but never before in California to the degree observed in the D-7 pool. With few exceptions, the original pressure in California fields is about equivalent to the static head of water below the water table in the outcrop. Structure The Ventura anticline is a prominent feature of the Ventura basin, being traceable on the surface about 17 miles.' The Ventura Avenue field is at the apex of the anticline. It is about one mile wide and five miles long, the major axis lying in an east-west direction. The productive limits cover an area of about 2300 acres. The entire anticline has been severely folded and faulted. The productive portions in particular are broken up by three major thrust faults having a general east-west strike. The resultant four fault blocks are termed the A, B, C, and D blocks, respectively. Certain electric-log intervals are assigned numbers. Fig I is a diagrammatic north-south section of the field near the crest, looking west, and shows three of the four fault blocks. To the west, the upper fault divides into two branches, which define the B block. Wells penetrating a fault may duplicate over 1000 ft of formation. However, the greater fault movement is the strike shift, which is believed to exceed 2500 ft both between the A and C blocks and between the C and D blocks. The location of water is irregular and unpredictable. A few intermediate waters exist, while some strata have more than 2000 ft of productive closure.

Jan 1, 1948

By Kent W. Pilz

Wet dust suppression can be achieved by 1) confinement of the dust within the dust producing area with a curtain of moisture, 2) wetting of the dust by direct contact between the particles and droplets of moisture or 3) the formation of agglomerates too heavy to remain airborne, or too heavy to become airborne, by combining small dust particles with each other and with the droplets of liquid. From the standpoint of economy, availability and safety, water is the ideal fluid; however, it is not as effective for dust suppression as when small percentages of specially formulated dust control compounds are blended with it. Performance of dust control com pounds is related to surface active agents and surface activity. In all liquids there is an attractive force between molecules which varies inversely as the sixth power of the distance between molecules. Thus, in the liquid phase where molecules are crowded together, the intermolecular forces are powerful; whereas in the liquid-vapor phase where the molecules are relatively far apart, these forces diminish rapidly. In the body of a fluid there is an uneven distribution of forces resulting in an inward pull called surface tension. The force which keeps two surfaces apart or causes them to coalesce is termed interfacial tension. Fluids of high surface tension exhibit poor wetting, spreading and penetrating qualities. Water has the unusually high surface tension of 72.75 dynes per cm at 20°C.

Jan 7, 1972

By George Bell

THE mine and milling plant of Demonstration Gold Mines, Ltd., is near the city limits of Baguio, Mt. Province, P. I. The mine road connects with the main highway to Manila. The nearest railway point is near sea level, approximately 40 miles distant. The Baguio district is very mountainous and has one of the heaviest rainfalls in the world. It is therefore difficult to maintain roads or to impound tailings and mine dumps. All supplies are trucked into the district direct from Manila or the nearest railway point, which means uncertain deliveries and high freight rates. Installation of equipment is difficult and costly. The average elevation at the mine is 4000 ft. and the climatic condi-tions.are ideal except for a three months rainy season. The company generates its own power for mining and milling opera-tions with three 400-hp. Ruston Diesel engines direct connected to 250-kw. General Electric alternating current generators. Labor conditions have been excellent, although at present social security laws are causing some unrest. Labor receives a higher average wage rate in this district than other labor in the Islands. The com-pany also furnishes free living quarters, hospitalization and work-men's compensation. Taxation has been reasonable up to the present time, but some of the new mining legislation may make it difficult to operate and pay dividends. The future depends largely upon the continuation of $35 gold and the political outcome in the Islands.

Jan 1, 1939

By Robert H. Hafner, Irvin R. Kramer

In recent years considerable interest has been shown in surface-alloyed metals, particnlarly those of chromium (chromized steels), which have excellent corrosion resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high tem- peratures of 1200º to 1400ºC. (2200° to 2550°F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- mon salt, and heated for approximately three hours at 930º to 1040°C. (1700º to 1900ºF.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900º to 1000ºC., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a Chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1943

By Robert H. Hafner, Irvin R. Kramer

In recent years considerable interest has been shown in surface-alloyed metals, particnlarly those of chromium (chromized steels), which have excellent corrosion resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high tem- peratures of 1200º to 1400ºC. (2200° to 2550°F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- mon salt, and heated for approximately three hours at 930º to 1040°C. (1700º to 1900ºF.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900º to 1000ºC., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a Chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1943

By AIME AIME

FREE competition, long the controlling ideal of domestic trade within the United States, has had the fundamental geographical advantage of functioning in the world's largest area of unrestricted commerce. Goods moved back and forth across state lines, unimpeded by customs, and industrial operations have developed rapidly to meet the expanding needs of a pioneer country richly endowed with natural resources. Fifty years ago, antitrust laws were adopted to protect the competitive private enterprise principle. It became illegal for one person to combine with another to restrain trade or commerce among the several states or with foreign nations. The original legislative measures defining this philosophy were the Sherman Act of 1890 and the Clay- ton Act passed in 1914. The development of Europe and other parts of the world was influenced by different conditions which led to a different theory of trade. Here were many small nations, with limited natural resources and a thin market, and they attempted to protect their national economy by tariff walls. International business arrangements for the purpose of diminishing the ups and downs of the more competitive system --crux of the modern cartel operations-seemed a logical device to stabilize production and guard the interests of both workers and consumers. European governments as well as European industrial interests became convinced that if com- petition could be held in bounds the danger of business depressions and un- employment could be reduced.

Jan 1, 1944

By John M. Sharp

John M. Sharp, Jr. (Assistant Professor of Geology, University of Missouri, Columbia, Mo.)-Geothermal gradient and surface temperature data anomalies are potentially useful tools in mineral exploration, These data, however, may reflect a number of geologic and hydrologic processes as well as the thermophysical properties of the geologic materials. The author presents a relatively simple model which may be of value in mineral exploration. The lack of consideration of other processes, however, limits its usefulness. For instance, because of erosion or sediment deposition over geologic time the land surface must be considered a moving boundary in such a model. Evaluation of this effect coupled with annual surface temperature and thermal conductivity variations can result in temperature profiles such as shown in [Figs. 4 to 7]. These effects and others, such as ground-water movement," must be considered and filtered from the data before proper interpretation is possible. Another assumption which should have been discussed is, why were the observed mean surface temperatures not used for extrapolation of the gradients in [Figs. 4, 6, and 7?] Conductive heat transport responds to the actual boundary (land surface) temperature, not to theoretical temperatures in the absence of perturbations. Benfield presents a theoretical model for calculating perturbations in the geothermal gradient for erosion and sedimentation. The temperature (T) at any time (t) and any depth below the surface (x) is given by [ ] where T is the mean surface temperature, G, the geothermal gradient, v, the rate of erosion (or sedimentation),[ ], the long-term rate of change of T0, and k is the thermal diffusivity of the rock. Using the author's values and a rate of erosion of 1.54 cm per yr for a period of 10,000 yr, a thermal profile as shown in [Fig. 10] will be generated. A thermal diffusivity of 0.0164 sq cm per sec was used, corresponding to a thermal conductivity of 0.0082 cal per cm per sec per C. In [Fig. 11], a sediment deposition rate of 3.0 cm per yr for a period of 1000 yr was used to generate the subsurface temperature profile. A surface temperature of 24.3°C was used, as specified in [Fig. 9, 7], was set equal to zero for both cases. Superposition on the generated profiles in [Figs. 10 and 11] of the annual surface temperature variation perturbation (which may be calculated in a number of ways) will yield profiles similar to those in [Figs. 4 and 7]. Similar profiles can also be produced by regional ground-water flow. Models like the author's can be of value in mineral exploration. Other processes, however, which affect surface temperatures and gradients must first be considered, calculated, and filtered from the data if anything but the crudest qualitative interpretation is to be made. Robert C. Edmiston (Author's reply)-Professor Sharp has raised three objections to my interpretation of the subsurface temperature data I collected at Silver Bell. These are: 1) No correction was made for erosion or sedimentation,

Jan 1, 1977

By Joseph Gurland

EVERAL carbide-cobalt compositions were pre-^-5 pared for the purpose of determining the transverse rupture strength of various carbide-binder systems. The binder content was held at 10 and 37 volume pct Co, so as to be representative of low and high bjnder compositions. The carbides used, WC, Tic, TaC, CbC, VC and ZrC, were selected on the basis of availability, knowledge of their properties, and small solid solubilities in the binder metal at room temperature. The methods of preparation and carbon analysis of the carbides are summarized in Table I. The carbides with cobalt added were ball milled, pressed, and sintered. vacuum sintering was used throughout, except for the WC-Cs alloys, which were sintered in hydrogen. The sintering temperatures ranged from 2500" to 2750°F for the low binder alloys and from 2300" to 2550°F for the high binder alloys. Compositions and properties of the sintered com- pacts are presented in Table 11. For the transverse rupture strength, the average and range of the five best samples of each alloy are listed. Discrepancies between the actual and theoretical densities are attributed to carbon deficiencies in some samples. The theoretical densities were calculated by assuming mixtures of carbides of stoichiometric compositions and cobalt. Representative microstructures are shown in Figs. 1 to 6. The porosity was A-2 or better' in all alloys except those with ZrC. A grain size of about 3 p was

Jan 1, 1958

By A. U. Seybolt

DURING the course of experiments involving oxygen equilibrations with a high-purity Pd-5 at. pct Rh alloy, the appearance of a subscale was noted. Most of the heat treatments in a pure oxygen atmosphere were performed at 900°C. The presence of the subscale was noted when the oxygen partial pressure was in excess of approximately 95 mm, up to 1 atm, the highest pressure used. According to available thermodynamic information' on the free energy of formation of Rh2O3 (the only reliably reported solid oxide of rhodium), this oxide should not be stable under these conditions, nor, of course, any oxide of palladium. Extraction of the subscale from the matrix was affected by treatment with aqua regia, and the resulting X-ray diffraction powder pattern is shown in Table I. This pattern is not that of Rh2O3, nor that of any known rhodium or palladium oxide. It can be indexed on a hexagonal lattice with a. = 5.22Å and co = 6.0Å. In addition to this unknown material, there was a weak Rh2O3 pattern. An X-ray fluorescence analysis of the powder gave 3214 palladium counts per sec and 5381 rhodium counts per sec, thus indicating the likelihood of a double oxide of palladium and rhodium. In view of the fact that the above result was obtained on a single sample, it is perhaps best not to insist upon the above ratio of about 0.6, but possibly to tentatively assume 0.5 or 1/1. The small amount of Rh2O3 in the X-ray pattern might have occurred on cooling, and it seems possible that the double oxide, below some temperature level, is not as stable as Rh2O3. To examine this point, some of the extracted double oxide was heated on a sheet of pure palladium in air at 900°C, and allowed to furnace-cool over a period of several hours. The X-ray diffraction pattern of the powder showed approximately the same intensity of Rh2O3 and the "hexagonal" oxide as before, but, in addition, a rather faint pattern of another crystalline species made its appearance. This finding again suggests partial transformation of the major (double) oxide to other oxides on cooling from 900°C. Application of the phase rule shows that only one equilibrium oxide (subscale) could have been present at temperature. Vacuum-fusion, oxygen analysis of the extracted subscale showed 7.7 ± 0.7 pct O. Combining this information with that of the X-ray fluorescence analysis suggests the formula PdRhO. This compound should have an oxygen content of 7.07 pct, which is within the range of error of the oxygen analysis. However, until a more careful stoichiometric study is made, it is suggested that the formula be written

Jan 1, 1965

By D. H. Baldwin, R. E. Reed-Hill

DURING the course of experiments involving oxygen equilibrations with a high-purity Pd-5 at. pct Rh alloy, the appearance of a subscale was noted. Most of the heat treatments in a pure oxygen atmosphere were performed at 900°C. The presence of the subscale was noted when the oxygen partial pressure was in excess of approximately 95 mm, up to 1 atm, the highest pressure used. According to available thermodynamic information' on the free energy of formation of Rh2O3 (the only reliably reported solid oxide of rhodium), this oxide should not be stable under these conditions, nor, of course, any oxide of palladium. Extraction of the subscale from the matrix was affected by treatment with aqua regia, and the resulting X-ray diffraction powder pattern is shown in Table I. This pattern is not that of Rh2O3, nor that of any known rhodium or palladium oxide. It can be indexed on a hexagonal lattice with a. = 5.22Å and co = 6.0Å. In addition to this unknown material, there was a weak Rh2O3 pattern. An X-ray fluorescence analysis of the powder gave 3214 palladium counts per sec and 5381 rhodium counts per sec, thus indicating the likelihood of a double oxide of palladium and rhodium. In view of the fact that the above result was obtained on a single sample, it is perhaps best not to insist upon the above ratio of about 0.6, but possibly to tentatively assume 0.5 or 1/1. The small amount of Rh2O3 in the X-ray pattern might have occurred on cooling, and it seems possible that the double oxide, below some temperature level, is not as stable as Rh2O3. To examine this point, some of the extracted double oxide was heated on a sheet of pure palladium in air at 900°C, and allowed to furnace-cool over a period of several hours. The X-ray diffraction pattern of the powder showed approximately the same intensity of Rh2O3 and the "hexagonal" oxide as before, but, in addition, a rather faint pattern of another crystalline species made its appearance. This finding again suggests partial transformation of the major (double) oxide to other oxides on cooling from 900°C. Application of the phase rule shows that only one equilibrium oxide (subscale) could have been present at temperature. Vacuum-fusion, oxygen analysis of the extracted subscale showed 7.7 ± 0.7 pct O. Combining this information with that of the X-ray fluorescence analysis suggests the formula PdRhO. This compound should have an oxygen content of 7.07 pct, which is within the range of error of the oxygen analysis. However, until a more careful stoichiometric study is made, it is suggested that the formula be written

Jan 1, 1965

The Palabora ore consists of two types, a carbonatite containing a low titanium magnetite, and a foskorite containing high titanium magnetite. The latter type also contains substantial quantities of phosphate. These two ore types are separately crushed and are kept separate through copper flotation and magnetic separation, for recovery of magnetite, with the low Ti magnetite being shipped as iron ore. High phosphate tailings are pumped to Foskor, a government-owned phosphate plant nearby. The Palabora plant was originally designed in 1966 for 33, 000 tpd using two 54 in. by 74 in. Allis -Chalmers gyratories; two 7 ft (2. 13 m) standards; four 7 ft shortheads; and six grinding lines, each using one 1,200 hp rod mill and two 1,200 hp ball mills. A fifth short- head and one more grinding line were added later; and with flowsheet improvements, the capacity of the plant was increased to 59, 500 stpd. A further plant expansion involving a third 54 in. primary and two 32 ft by 15 ft (9.75 by 4.6 m) 9,000 hp autogenous mills and another flotation section will bring its capacity to 87,500 stpd in 1977. These two fully autogenous mills are constructed entirely out of doors near the primary crusher, and the ground ore will be pumped a mile to the concentrator by a five-stage pumping system. The Palabora ore is mined with 6, 10, and 12 7d (4.6, 7.6, and 9. 2 cu m) shovels and hauled to the crushers in 110 and 165 st trucks. Sixty-five ton trucks were originally used, but the crusher dump pockets were designed for larger units. Dump pockets, crushers, feeders, and take- away belts are offset in order to keep the two ore types separate. Centerlines of the crushers are only 43 ft (13. 1 m) apart; but, because of their being offset, maintenance room is ample. Initially, more carbonatite ore than foskorite was mined; but as the pit has deepened, this ratio has been reversed. The Palabora ore breaks in the pit with a large amount of oversize boulders; and, with the use of larger trucks, a splitter has been installed on one side of each dump pocket to protect the crusher spider. Smaller trucks dump on the opposite side. To accomodate the splitter, the pocket edge has been raised one meter and moved back one meter. Dust is collected through a special vent shaft between the crushers and the mantle relining area; but even so, two high-pressure water spray headers with nozzles are installed under the edge of the pocket at each dumping position. While only one truck dumps at a time, sprays from all four headers are used to suppress dust. Any leakage of water through the seal around the upper bowl of the crusher is caught by a circular trough under the seal and directed to a sump pump. At this point, there

Jan 1, 1978

By A. Coskun, J. F. Elliott

The activity of aluminum in liquid Al-Fe alloys .has been measured by an improved version of the transportation method in which the metallic vapor has been collected by its solution in a metallic condenser. The results can be represented by the equation: log yAl = -3.0(1 - xAl2) (0.6 < XAl < 1.0) This equation applies at 1315°C. MORRIS and zellarsl adapted the transportation method for measuring the vapor pressure of a com- ponent of an alloy at high temperature. We have modified their technique further2 for use with metals that are strong oxide formers. In the present case the method has been applied to the Al- Fe system to obtain the activity of aluminum in the liquid region at 1315°C. Dried ultrahigh-purity hydrogen (Matheson) is the carrier gas. The operations, Fig. 1, of deoxidizing the gas, equilibrating the gas with the sample at 1315";, and then collecting the aluminum vapor are all accomplished within a single, continuous alumina tube to avoid contamination of the system by leaks. De-oxidation to a very low level of PO2 (<10-25 atm) is Obtained by passing the hydrogen through a tightly packed bed of aluminum powder. The temperature of this bed increases to approximately 550°C in the direction of the gas flow. The boat containing three pellets of the alloy is supported on the end of a

Jan 1, 1969

By R. V. Norris

THE wage rates and working conditions in the anthracite. region of Pennsylvania have been governed for nearly 20 years by the award of the Anthracite Coal Strike Commission, appointed Oct. 16, 1902, by President Roosevelt. The report of this com-mission, made in March, 1903, was accepted and, with eight modifications made at various dates, has had .almost the force of law, and has kept this great indus-trial region free from strikes for almost a generation. In 1920, President Wilson appointed an Anthracite Coal Commission, and its report, accepted Aug. 30, 1920, governed wage conditions to April 1, 1922. Actually, the agreements have been for terms of two to four years, and lately, in 1916 and 1920, the employ-ees have continued at work pending the negotiation of new agreements which were made retroactive, and which have all been modifications of the original 1903 award. With the expiration, April 1, 1922, of the 1920 award approaching, Mr. Lewis, president, of the United Mine Workers of America, addressed a letter, on Feb. 20, to the operators, suggesting a meeting on March 15; this date was accepted by the latter, with the notation that the time was short. At the meeting, the Mine Workers presented 19 demands, and advised that if a satisfactory agreement was not reached by April 1.a suspension of mining would occur, contrary to the practice since 1916 of continuing work with a retro-active adjustment.

Jan 6, 1922

By B. M. Larsen, T. E. Brower

A perspective is presented of the steel plant sulphur distribution and elimination problem from coal to liquid steel ready for teeming, giving distributions of sulphur over a range of coke sulphur content, and some methods of sulphur control, in the blast furnace, external desulphuriza-tion between blast furnace and open hearth, distribution between fuel, slag, and metal, and methods and limitations of control of sulphur in the open hearth furnace. AS a part of the 1951 AIME symposium on sulphur in steelmaking, it was thought that a discussion of the distribution of sulphur throughout the whole series of operations, from coal and ore to finished steel ingots, might have some value in giving a perspective on the whole problem. The following discussion is an attempt to present such an overall picture. The order is that of the actual plant operations, beginning with a very brief consideration of the coking process. Sulphur in Coal and Coke Since by far the largest source of sulphur entering the steelmaking cycle is in the coal used to make coke for the blast furnace, it would seem reasonable to eliminate some of it, either from the coal, or the coke, or during the coking process. This has appeared impracticable up to the present, at least, for two main reasons: the low activity of the organic sulphur in either coal or coke, and because of price limitations involved in treating a low cost material such as coke. A variable portion, usually M or less, of the sulphur is present in coal in the form of pyrites or similar compounds, and a large part of this sulphur may be removed in the coal washery. Most of the sulphur, however, is normally present as "organic" sulphur, intimately associated with the coal structure. Its distribution prevents any separation by mechanical means. Its low activity makes improbable &apos; any rapid chemical removal, although hydrogen will remove sulphur from both coal and coke. Thus, prolonged recirculation of coke oven gas in the coking process would tend to leave a smaller percentage of the total sulphur in the coke residue. Table I shows a typical distribution of sulphur from coal into products in the coking process. As the sulphur in the coal increases, the sulphur in the coke tends to increase in about the same proportion. Sulphur in the Blast Furnace The best picture of the situation in the blast furnace is provided by a sulphur balance of raw materials entering, and of products leaving, the furnace. The difficulties in accurate weighing and sampling of the variable solid materials entering this process, and the number of hours required for the raw materials to descend through the furnace under variable operating conditions, make it difficult to obtain an accurate balance. However, balances made over periods of weeks or months tend to average out some of these uncertainties. Table I1 presents three typical sulphur balances similar to a number that the writers have calculated. In most of these the slag volume calculated from the sulphur balance is, in some instances more, and in other instances less, than the value corresponding to the best input and output balances of the other slag constituents (lime, silica, alumina, etc.). Probably the greatest source of error in these calculations is the sulphur content of the slag. Despite some possible inaccuracies the balances of Table II show rather definitely the following points: 1—That 87 to 95 pct of the total sulphur input is in the coke and 95 to 97 pct of the total sulphur output is in the slag. Also, that if any sulphur leaves the furnace with the gas it is relatively small, amounting to a possible 1 pct or less. 2—At the lower sulphur coke level of 0.86 pct the total amount of sulphur charged is 15 Ib of sulphur per ton iron increasing to 26 lb per ton at the higher sulphur, intimately associated with the coal struc-rare burdens containing sulphur-rich ores will the total sulphur burden fail to be nearly proportional to the content in the coke used. 3—The 7 to 9 pct of the total sulphur input from the limestone of furnaces B and C is due to the relatively high sulphur content of the stone, 0.226 and 0.265 pct, respectively. In the case of furnace A, the sulphur content of the limestone was only 0.06 pct which resulted in only 3 pct of the total sulphur input coming from this source. It is rather interesting to compare the sulphur balances of a typical ferromanganese furnace with

Jan 1, 1952

By F. M. Morris

A large reserve of thick coal in southwest Virginia was developed by Clinch-field Coal Co. in 1957-1958 to produce a nominal rate of 1500 tph raw coal. Operation features coal cleaning in transit. Refuse removed averages 35 pct. Evolution of plant from initial conception to completion is discussed, selection of means applied is explained, and performance to date us design expectation is described. The long-range plan calls for ultimate handling capacity of 40,000 tpd raw coal with anticipated clean coal capacity of 26,000 tpd on a three-shift basis. From a materials handling viewpoint, the Moss No. 3 operation is principally of interest as an ensemble. Generally speaking, it uses time-tested equipment and ideas but some of these are employed on a scale that may be new in the industry. At present about 20,000 tpd of raw coal are being handled. This is expected to increase to 40,000 tpd as soon as business conditions justify it. The purpose of this paper is to discuss the evolution of the plant as to materials handling practices, to describe briefly the equipment and methods used, and to comment on performance in certain areas. The subject divides itself naturally into four phases: 1) operations at the mines, 2) transportation from mines to plant, 3) raw coal handling into the plant, and 4) transportation of refuse away from the plant. OPERATIONS AT THE MINES The coal reserves for Moss 3 are in southwest Virginia where Dickenson, Russell, and Buchanan Counties come together. This area contains about 15 square miles and over 100,000,000 tons of coal. Here the No. 4 (Tiller) and No. 5 (Jawbone) seams of the Norton Formation lie so closely together that for practical purposes, they constitute one seam of coal. This seam, which is called the Thick Tiller, varies from 10 to 18 ft in thickness and underlies Sandy Ridge, a mountain cresting between 2400 and 3300 ft above sea-level. At 18-ft seam height (which is considered to be the maximum practical mining height) the parting between seams will be about 3 1/2 ft thick and each bench of coal will be about 7 ft thick. Depending on the amount of impurities in the seams Drover. total reject in this height coal may approximate 50 pet by wt. It will average about 35 pet for the property as a whole. The first move in developing this resource was made in 1953 when contour maps of several square miles around Duty, Va., including all the known outcrop, were made by photogrammetry. At this time, it was felt the prospective operation would be served by the Clinchfield Railroad and a photogrammetric route survey was made by this railroad from Haysi to Duty. Study of the resulting maps indicated only one site—adversely owned—which might accommodate the size washing plant to be erected. Water resources of a dependable nature seemed nonexistent. In 1954 bulk washability tests were made on the Tiller Bench at the Moss No. 1 preparation plant. The tests indicated this portion of the seam, mined separately, would wash to 4 pet ash with good recovery. Also in 1954, development of Moss No. 2, south of Sandy Ridge, was begun. This mine is in the Tiller Seam where it is about 100 ft below the Jawbone Seam. The reasons for developing a mine in the normal Tiller Seam before tackling the Thick Tiller seemed compelling: Railroad service could be established quickly, communications were better (though not good!), more was known of the seam (it had been mined in the years 1911 to 19241, and there was no essential property to be acquired. After some legal skirmishing, the Norfolk & Western Railroad was granted the right to serve the new mine. Three decades earlier the old mine had been served by the Clinchfield Railroad. The event which triggered active development of Moss 3 was the Appalachian Power Co.&apos;s decision in 1956 to build a 450,000-kva power plant on Clinch River at Carbo. This solved the problem of marketing the steam coal which inevitably must be a product of a mine in the Thick Tiller. Management promptly decided to build the preparation plant at Carbo where an excellent site was owned; where railroad service existed; where telephone service could be obtained; and where roads, bridges, and water supply were tolerable.

Jan 1, 1961

By Gerald Sherman

LARGE part of the mining industry is still under the shadow of the depression, and unwilling to undertake changes in plant or methods of operation that require large preliminary expenditures of money. Certain metals command fair prices: nickel, tin, and molybdenum. The precious metals, gold and silver, have been given greater values by natural processes of economics or by proclamation, but are of so much less importance in industry, in total value, and number of men employed, that they have not greatly raised the average for the mining business. The increased value of gold which was established in 1933 has stimulated .the search for new deposits, and aided efforts to revive some of the old mines &apos;Where it is hoped to find quantities of marginal ore now become profitable. The higher price did not increase production very much for 1934, but two discoveries of major importance, and others yet to be proved, will help later. The two referred to are the Lupa gold field in Tanganyika Territory, and the Silver Queen mine on Soledad Mountain near Mojave in California. The first was recently discovered, and is being developed by the East African Goldfields, Ltd. Uncompleted explorations of the croppings early in the year had exposed for measurement and sampling to a shallow depth, three ore shoots as gregating 7400 ft. in length and 6 ft. in width, containing 0.375 oz. of gold per ton. In the Silver Queen. an ore-

Jan 1, 1935