Search Documents

By AIME

THE wind howls almost incessantly over the mining engineers working in the near desert that is the Division of Namaqualand, the upper Atlantic coastal corner of South Africa's Cape of Good Hope Province. But when these men at the U. S.-owned mines called Nababeep South and East O'okiep (pronounced Oh-keep) tell you about their achievements, they can be heard above the wind. For their O'okiep Copper Co. Ltd. now produces over half the Union of South Africa's annual output of 30,000 tons of copper metal. Moreover, it is a very decent sample of U. S. geotechnical imagination. financial daring, and managerial skill, all operating successfully in a

Jan 1, 1947

By Donald B. Hunter

The Ti-Be system up lo 10 wt pct Be with cortlmercialll' pure titanium has been determined using metal-lographic techniques. Beryllium forms the p eutec-toid type of dinqarz with titanium; the eutectoid occurs at 0.5 xt pct Be azd 1500 F, while an eutectic is foritled at 1887°F containing between 5 and 7.5 rt pct Be. The solubility of beryllium in a titanium does not exceed 0.05 zvt pct and the maximum solubility of Beryllim in 0 titanium is 1 wt pet. PREVIOUS work on the Ti-Be phase diagram indicated that additions of beryllium to titanium resulted in a marked lowering of the melting point,''' and it was also observed that the solubility of beryllium in both a and p titanium was retricted.- With the limited data available, McQuillan and McQuillan constructed a partial hypothetical diagram of the Ti-Be system,= assuming that beryllium formed the 0 eutectoid type of system with titanium. Subsequently Bedford published a tentative diagram of the entire Ti-Be system: although he did not investigate alloys containing less than 10 wt pct Be. This diagram included several compounds described by other authorities.'-l3 The following account describes work directed toward determining the form of the titanium-rich portion of the phase diagram up to 10 wt pct Be. MATERIALS AND METHODS Titanium sponge and a master alloy containing 25 wt pct Be were used in the formulation of the alloys; the chemistry of these materials is detailed in Table I. The alloys were prepared as 250-g compacts which were melted into buttons by arc melting under purified argon on a water-cooled copper hearth. Results of analyses for beryllium are shown in Table I but no determination of other elements was made at this stage. The alloys were hot-rolled at 1650°F to produce 0.1-in.-thick sheet. Alloys containing up to 1.5 pct Be were fabricated without trouble; samples containing 2 pct cracked initially upon hot rolling, but thereafter rolled satisfactorily to sheet. The 5, 7.5, and 10 pct were hot short and could not be rolled. Surface contamination was removed from samples by sandblasting and pickling in a 5 pct HF-35 pct HNOs solution. For metal log raphic examination, heat-treated specimens were mounted transverse to the rolling direction, ground on silicon carbide papers of increasing fineness to 600 grit, and electropolished at 20 v using a solution containing 600 ml of methanol, 60 ml of perchloric acid, 360 ml of butyl cellosolve, and 2 ml of Solvent "X". Difficulty was experienced in obtaining good electropolished surfaces with samples containing more than 1 pct Be, the degree of difficulty in-

Jan 1, 1967

By R. R. Seeber

(Pittsburg Meeting, March, 1910.) IN the copper-mining district of northern Michigan a fair-sized mine usually operates two or more shafts along the strike of the lode, these shafts being usually at least 1,000 ft. apart. The tonnage to be hoisted from each shaft is large-from 13,000 to 25,000 tons per month. The hoisting-engines used are generally steam-driven, non-condensing, duplex engines with Corliss valves, supplied by steam from separate boiler-plants where the distance between shafts is great. In an attempt to centralize power-plants and secure central-station economies, the Winona Copper Co. installed an electric hoist of the Ilgner type, with Ward Leonard control. A brief description of this plant has already been published.1 The only point of variation from the simple Ilgner set lies in the connection of two generators to a single induction-motor by flexible couplings. These generators serve motors which operate hoisting-drums at separate shafts, viz., No. 4 shaft, Winona, and No. 1 shaft, King Philip. , The hoist for No. 4 shaft, is about 1,700 ft. from the power-plant, and in this building the motor-generator set is placed. No. 1 King Philip hoist is 1,500 ft. from the motor-generator set. The equipment of the motor-generator set is as follows: In the middle of the set is a 12-pole, 450-h-p., 600-rev. per min., 2,080-volt, three-phase, 60-cycle, variable-speed induction-motor, connected on each side to a 20-ton fly-wheel which is 10 ft. in diameter, and to a 6-pole, 170-kw, 575-volt, interpole, direct-current generator. On each side of the shaft is placed a separate exciter, which delivers current at 125 volts. The lubrication of the four main bearings that support the fly-wheels * Presented also, by mutual agreement, at the meeting of the American Institute of Electrical Engineers, New York, N. Y., Mar. 11, 1910. Engineering and Mining Journal, vol. lxxxviii., No. 3, p. 110 (July 17, 1909).

Sep 1, 1910

Jan 1, 1967

By Oswald J. Heinrich

THE origin of spontaneous combustion in collieries is, of course, chiefly due to bad system in laying out the pits, unclean workings, insufficient ventilation, and neglect in damming off works after they are exhausted of the main coal. This is particularly indispensable in the Richmond field, because it is difficult and dangerous here, on account of the inferior roof, to remove the last vestiges of coal ; and we are compelled also to retain all the slates and bands, as far as possible, in the pit, to help fill up, although such material is liable to fire. This, however, can be prevented to a great extent, as mentioned below. I am satisfied that the only system of working this thick coal is by cross-cutting (Querbau, ouvrage & travers) or working in benches, as practiced in France (Creusot, Rive de Gier, St. Etienne), in Silesia (Kiinigsgrube), which I have used as far as it is practicable in an old pit, almost torn to pieces by former workings. Modifications may, of course, be needed, even in the same pit, on account of irregularities in the seam. I am also satisfied for economical reasons (on account of the heavy cost for timbering) that pits here ought to be worked upwards, even if it requires a longer period of time to win the coal, and a greater outlay of capital to commence with. The various saddle-shaped " troubles " making natural minor basins in the main basin aid in the execution of this plan. A pit worked once ought to be worked out clean, given up, and dammed off forever. If sections of proper height are assumed, according to the required amount of production for a certain period of time, they ought to be worked out and filled in as much as possible, dammed off, and ultimately allowed to fill up with water, in order to protect the upper works in future from fire in the gob below. This I consider indispensable, because we may not be able profitably to fill in all the ground. To do so we have to use the waste of the mine, although it is liable to fire in time. In using this stuff, it ought to be surrounded by walls of rock not liable to take fire, laid firmly in clay, the gob being in the middle, and firmly covered and packed with clay on top. In

By E. A. Gulbransen, J. W. Hickman

DURING the past two decades considerable progress has been made in the art of manufacturing heater alloys. The conventional iron-chromium-nickel alloys have been improved by the addition of small quantities of other elements. Up to the present time, to our knowledge, there has not appeared a systematic study of these alloys where the newer tools of investigation have been brought to bear on the problem. It is not yet clear what roles the additional elements play in increasing life time in usage. As a first approximation one might guess that elements such as manganese, silicon, zirconium, calcium and aluminum would aid in the formation of a protective film on the alloy surface, thus retarding the oxidation rate and increasing lifetime. If these additional elements do form protective oxides in the outer surface of the oxide film, it may be possible to identify them by means of reflection electron diffraction. It is also possible that the additional elements may not diffuse to the surface but may remain at the interface between the oxide and the metal. Then, too, the major elements in the alloys undoubtedly form oxides which are stratified on the surface. If the minor elements concentrate in a layer in contact with the substrate where they undergo oxidation and if this oxide film offers resistance to the diffusion of iron, chromium and nickel ions, then the lifetime of the heater element might be expected to increase. It is also possible that preferential reduction in the diffusion rates of the several ions may Occur to such a degree that oxides may form in the body Of the film and On the outer surface which are different from those that would normally form if the additional elements were not present. The use Of transmisson electron diffraction may aid us in jnterpreting these phenomena. UP to the Present time all Of the factors which influence the lifetime of a given heater element are not definitely known. Among these are: (I) The rate of oxidation of the alloy. This may be dependent upon the composition and the physica1 state of the "alloy. (2) The stability of the structure of the coating which forms. Transitions from one structure to another or solid phase reactions resulting in a change of composition may occur. The tendency of the film to adhere to the substrate when heated and cooled successively will be important. (3) The evaporation of various constituents from the alloy such as the remova1 of carbon by Oxygen in a decar-burization reaction. With these possibilities in view, an electron diffraction study of the oxides occurring on six different nickel-chromium alloys was undertaken with the hope that the results of this study could be correlated with oxidation rate studies as determined by means of the vacuum microbalance method1 and with lifetime tests carried

Jan 1, 1949

CYRIL STANLEY SMITH, Chairman CARL E. SWARTZ, Past-Chairman ARTHUR PHILLIPS, Vice-Chairman E. E. SCHUMACHER, Vice-Chairman H. A. MALONEY, Treasurer FRANK. T. SISCO, Secretary 9 West 39th Street, New York, N. 1. Executive Committee 1944 1945 WILLIAM C. ELLIS C. S. BARRETT ALAN MORRIS T. A. WRIGHT KENT R. VAN HORN L. L. WYMAN

Jan 1, 1943

By P. A. Beck, M. N. Parthasarathi

In high purity aluminum single crystals grown by the strain-anneal method (primary re crystallization after a small deformation) Lacombel observed sub-boundaries with disorientations of 1 to 3 deg. In commercial and high purity aluminum crystals grown by the same method Tiedema observed sub-boundaries with disorientations of about 20 min of arc, radiating from a =nuclear spot," centrally lo-

Jan 1, 1959

By Khosrow Bakhtar

A series of nineteen shear tests were performed on fractures 1 m2 in area, generated in blocks of sandstone, granite, tuff, hydro- stone and concrete. The tests were conducted under quasi-static and dynamic loading conditions. A vertical stress assisted fracturing technique was developed to create the fractures through the large test blocks. Prior to testing, the fractured surface of each block was characterized using the Barton JRC-JCS concept. The results of characterization were used to generate the peak strength envelope for each fractured surface. Attempts were made to model the stress path based on the classical transformation equations which assumes a theoretical plane, elastic isotropic properties, and therefore no slip. However, this approach gave rise to a stress path passing above the strength envelope which is clearly unacceptable. The results of the experimental investigations indicated that actual stress path is affected by the dilatancy due to fracture roughness, as well as by the side friction imposed by the boundary conditions. By introducing the corrections due to the dilation and boundary conditions into the stress transformation equation, the fully corrected stress paths for predicting the strength of fractured blocks were obtained.

Jan 1, 1984

Jan 1, 1970

By Malcolm C. Bridges, Ian A. Goddard

INTRODUCTION Mount Isa mine is a major producer of both copper and lead-zinc- silver ores. During the 1975/76 year, 4.3 million tonnes of copper ore were extracted at an average grade of 3.4%, and 2.4 million tonnes of lead-zinc-silver ore at average grades of 7.0%, 6.7% and 173 grams per tonnes respectively. Systematic lead-zinc mining has continued for just over 45 years and copper mining for just over 30 years. Virtually all mining is underground. The composite and somewhat schematic longitudinal section of Figure 1 shows the overall distribution of ore at the Mount Isa mine. The mine can be roughly divided into two parts about a central shaft complex: to the north there is predominantly lead-zinc ore and to the south there is copper ore. Underground operations are serviced by three shafts in the central shaft complex (P61, R62 andU62) and another to the south in the copper mining area (X41). Mining is spread over a total strike length of 2.9 km and extends to a depth of 960 m. Currently, lead-zinc ore is being extracted between 15 and 11 levels and is hauled to the central ore-hoisting shaft on 13 and 15 levels. Copper ore is being extracted between19 and 13 levels and is hauled to the central shafts on 19 level. The principal lead-zinc mining methods used now, as they have been over the last ten years, are sublevel open stoping and cut-and- fill stoping, with about equal tonnages of ore from each (Figure 2). Since about 1970, there have been several interesting developments in lead-zinc mining methods and procedures, principally: • the development of an effective method for the recovery of pillars between open stopes and • the evolution of safer and more productive cut-and- fill methods. During this period also, the focus of mining has moved 120 m deeper

Jan 1, 1977

Texture Transition in Ordered CuAu, by E. A. Starke, Jr., J. C. Ogle, and C. J. Sparks, Jr., Trans. TMS-AIME, 1969, vol. 245, pp. 169-70. pole figures should have had two parts not one. On the Estimation of Oxygen Absorption by Continuous Molten Metal Streams, by J. Szekely, Trans. TMS-AIME, 1969, vol. 245, pp. 341-44.

Jan 1, 1970

By M.A. Hunter

This paper gives the results of an investigation of the specific resistance and temperature coefficient of the electrical resistance of nickel and its important alloy, monel metal. For most of the pure metals, the temperature coefficient of resistance is approximately 0.004 per degree centigrade at 20" C. Nickel and iron, however, are exceptions. This property is important as it gives us good material for the construction of thermometers and other instruments involving electrical control. A summary of information on this subject has been publishcd by the Bureau of Standards.l The present experiments antedate this publication by several years and as the information obtained is not contained in it, the results of the experiments arc published as additional information. Electrical Properties of Pure Nickel It is generally conceded that the lowest values for electrical resistance are obtained in the purest metal. In the case of nickel, the best material obtainable is electrolytic nickel, which contains approximately 99.80 per cent. nickel, 0.15 per cent. iron, and 0.05 per cent. copper. Any cobalt that may be present is included in the nickel figure. If the elcctrolStic sheet has been deposited without intermission, it is possible to cut a section from the sheet and roll it into wire without melting. By this means a nickel wire may be obtained that is uncontaminated by any of the impurities always taken up by nickel during melting. Two samples of nickel wire obtained from different electrolytic nickels had the follolving electrical resistance and temperature coefficient of electrical resistance: Specific Temp. CofEE. Sample MateRial ReSISTance peR Deg. C. NO. 1 Electrolytic nickel.................... 7.55 0.00550 NO. 2 Electrolytic nickcl ................... 7.60 0.00553 * Rensselacr Polytechnic Institute. Director of Research, Driver-Harris Co. Russell Sage Laboratory, Rensselaer Polyt,ecllnic Institute. 1 U. S. Bureau of Standards, Circular 100 (March, 1921).

Jan 1, 1923

By M. A. Hunter

This paper gives the results of an investigation of the specific resistance and temperature coefficient of the electrical resistance of nickel and its important alloy, monel metal. For most of the pure metals, the temperature coefficient of resistance is approximately 0.004 per degree centigrade at 20" C. Nickel and iron, however, are exceptions. This property is important as it gives us good material for the construction of thermometers and other instruments involving electrical control. A summary of information on this subject has been publishcd by the Bureau of Standards.l The present experiments antedate this publication by several years and as the information obtained is not contained in it, the results of the experiments arc published as additional information. Electrical Properties of Pure Nickel It is generally conceded that the lowest values for electrical resistance are obtained in the purest metal. In the case of nickel, the best material obtainable is electrolytic nickel, which contains approximately 99.80 per cent. nickel, 0.15 per cent. iron, and 0.05 per cent. copper. Any cobalt that may be present is included in the nickel figure. If the elcctrolStic sheet has been deposited without intermission, it is possible to cut a section from the sheet and roll it into wire without melting. By this means a nickel wire may be obtained that is uncontaminated by any of the impurities always taken up by nickel during melting. Two samples of nickel wire obtained from different electrolytic nickels had the follolving electrical resistance and temperature coefficient of electrical resistance: Specific Temp. CofEE. Sample MateRial ReSISTance peR Deg. C. NO. 1 Electrolytic nickel.................... 7.55 0.00550 NO. 2 Electrolytic nickcl ................... 7.60 0.00553 * Rensselacr Polytechnic Institute. Director of Research, Driver-Harris Co. Russell Sage Laboratory, Rensselaer Polyt,ecllnic Institute. 1 U. S. Bureau of Standards, Circular 100 (March, 1921).

Jan 1, 1923

By John W. Cahn, John E. Hilliard

Single crystals of copper and silicon-iron were cold rolled in orientations chosen to produce individually the major components of the poly crystalline deformation texture. The orientation dependence of the recrystallization kinetics was studied relative to the primary recrystallization textures of these specimens. It is not possible to rationalize the poly crystalline re crystallized textures on this basis. The results suggest an important role of the interaction of adjacent crystals during the deformation of aggregates. BRICK and Williamson1 first noted evidence that the recrystallization temperature was different for straight-rolled and cross-rolled copper given comparable reductions. Michalak and Hibbard2 investigated quantitatively the effect of rolling procedure on the kinetics of recrystallization of cold-rolled copper and found that material cold-rolled the same amount by straight-pass, cross-pass, and compression-pass techniques developed different deformation and recrystallization textures, different 1-hr recrystallization temperatures, and different recrystallization kinetics. However, the temperature dependence of the rate of recrystallization was essentially the same for all techniques. Similar results were obtained on iron. Dunn and Koh3 in studying the recrystallization textures of cold-rolled silicon-iron single crystals reported large differences in the annealing temperatures and times required to recrystallize specimens of different orientations cold-rolled the same amount. Liu4 and Liu and Hibbard5 utilized the concept of different recrystallization temperatures for different orientations of cold-rolled crystals to rationalize the difference in recrystallization textures found in various face-centered-cubic metals. Their explanation predicted a significant difference in the recrystallization kinetics of deformed (110) [112] crystals as compared to (358) [352] crystals, and, in fact, Liu4 reported evidence that this difference existed at least qualitatively. Verbraak6 who rolled and recrystallized a series of copper single crystals found that the double (112) [111] rolled orientation is related to recrystallized cube texture formation. The effect of rolling intensity on the relative amount of cube component suggests an important role of recrystallization kinetics. Walter and Hibbard7 while trying to relate the behavior of rolled and recrystallized single crystals of silicon-iron to the behavior of polycrystal-line silicon-iron again noted that differences in recrystallization kinetics were necessary to rationalize their results. The purpose of the present investigation was to obtain quantitative kinetic data on the recrystallization of single crystals of both copper and silicon-iron rolled to initial isolated individual orientations corresponding to those found in the polycrystalline deformation textures. These data might indicate the importance of the deformation orientation, i.e. the range of available nuclei, the deformed matrix orientation into which these nuclei grow, and the orientation dependence of their growth rate during primary recrystallization on this texture. I. COPPER Experimental Procedure—A single crystal of 99.98 pet purity copper, grown by the Bridgman technique, was purchased in the form of a bar 1 1/2

Jan 1, 1962

By Edward C. Stephens, Robert R. Coats

High-grade copper ore was discovered in 1932 in the long-dormant Mountain City (Cope) mining district, Elko County, Nevada. From 1932 to 1947, the one producing mine in the district, the Mountain City Copper Mine, produced 1,109,878 short dry tons of ore averaging 9.745 per cent copper, 0.274 ounces of silver, and 0.0057 ounces of gold per ton. The Mountain City Copper Mine is developed in eugeosynclinal rocks of Ordovician age, the Valmy Formation, which is part of the upper plate of the Roberts Mountains thrust. On the Valmy were deposited unconformably first, a elastic formation of Devonian or Mississippian age, the Grossman Formation, succeeded unconformably by a ·sequence of three conformable formations, the Banner, the Nelson, and the Mountain City. The Banner Formation probably is early Late Mississippian in age; the ages of the Nelson and Mountain City are not known precisely but are believed to be of Late Mississippian and Carboniferous(?) age, respectively. A thick formation of elastic rocks, limestone, and volcanics, the Reservation Hill Formation, has been thrust over the Mountain City. The age of the Reservation Hill is unknown but is presumed to be Pennsylvanian(?) and Permian(?). Several plutons of Cretaceous quartz monzonite intrude the Paleozoic formations; they and the intruded formations have been laid bare by erosion, and several sequences of volcanic rocks of Miocene and Pliocene age, and perhaps in part older, have been successively deposited on irregular erosion surfaces. The primary mineralization of the Mountain City Copper Mine is believed to postdate the deposition of the Nelson Formation and to predate the intrusion of the quartz monzonite. The primary ore bodies are lenticular in shape and are composed largely of quartz, pyrite, and chalcopyrite. The ore lenses, in general, strike northwestward and dip northward. They occur in the Valmy Formation within a definite stratigraphic sequence composed largely of shales with associated minor quartzite lenses. The ore is epigenetic. The principal ore body, the "200," was completely leached to the 200 level. Abruptly beneath the barren gossan was supergene copper sulfide ore, much of which assayed 50 per cent copper. The secondary copper minerals are sooty and massive chalcocite, bornite, and covellite. The supergene enrichment of the ore may have required a large part of Tertiary time.

Jan 1, 1968

By AIME AIME

AWRDED jointly by the four AW Founder Engineering Societies the John Fritz Medal is generally regarded as the most signal honor that American engineers can confer on a fellow engineer. The roll of 34 recipients contains the names of Lord Kelvin, George Westinghouse, Alexander Graham Bell, Thomas. A. Edison, George W. Goethals, Guglielmo Marconi, and Michael I. Pupin; and among members of the A.I.M.E. now living, Sir Robert A. Hadfield, Herbert Hoover, and Daniel C. Jackling. On the evening of March 1 7 the name of Paul Dyer Merica was formally added to this list of illustrious engineers when the medal was presented to him at a dinner at the Metropolitan Club in New York. The citation read. For important contributions to the development of alloys for industrial uses. Arrangements for the dinner were made by the following committee representing the four Founder Societies: R. C. Allen, George S. Davison, A. A. Potter, and J. B. Whitehead.

Jan 1, 1938

By David W. Brunton

(San Francisco Meeting, October, 1911.) MINE-DRAINAGE and the ever-increasing demand for water on the plains have within the past few years necessitated the driving of a great number of adits and tunnels, including many of considerable size and great length. In most instances, ex isting conditions have called for extreme rapidity of execution; and this necessity, coupled with the high altitudes at which most of the work has been carried on, excessive freight-rates, and difficulty -of access, has involved many complex and interesting problems. One of the most rapidly executed undertakings of this class is the Laramie tunnel, recently completed for the Laramie-Poudre Reservoirs & Irrigation Co. This tunnel is driven through Green ridge, a spur of the Continental Divide, which separates the Laramie river from the Cache-la-Poudre in Laramie county, Colo. Green ridge is extremely persistent, and further northward in Wyoming is known as Sherman hill, the highest point on the Union Pacific railway. At the point where the tunnel is driven, two opposing bends bring these streams within 2.5 miles of each other, with a difference in elevation of 500 ft. The rock exposed on the banks of the two rivers does not differ materially in hardness; and, without a geological study of the conditions involved, it would appear that the difference in the depth of erosion of the two streams is due principally to the greater volume of water at this point in the Cache-la-Poudre, which has a drainage-area above the tunnel-portal of 110 sq. miles, as against 30 sq. miles of natural drainage for the Laramie. To increase the water-supply at the tunnel, however, this latter amount has been augmented by two side collection-canals, which bring the available drainage-area up to 84 square miles. The nearest railroad shipping-point to the eastern portal is

Apr 1, 1912