Search Documents

By James Magee

THERE is nothing new about drag-line dredging for placer gold. The use of the separate unit for excavating preceded the large barge with excavator mounted upon it, which has reached a high state of perfection through use in every part of the world. But at present there is a vogue for a small, inexpensive plant combining a drag-line excavator on cater-pillar mounting and a gravel-washing plant on a floating barge. The most efficient ones use a bucket of 1 to 2 yd. capacity with boom from 40 to 70 ft. long. The barge varies from 20 by 30 ft. to 36 by 48, and carries the trommel screen, pump, riffle sluices and power engine.

Jan 1, 1936

By E. H. Rose

IN a year of sober reflection and stocktaking after the mineral-squandering spree of World War II, the role that beneficiation of low-grade must henceforth play in American mineral industry has become unmistakable. From the volume of research and development progress in mineral engineering during 1946, mineral dressers evidently have ample resoluteness to meet the challenge. Perhaps ,the most conspicuous trend of the year was the renascence of interest in gravity concentrating methods and more serious effort than ever before to make them effective in finer size ranges down to 200 mesh. This has been forced by the problem in iron ores where the low value of the product will not support a high flotation reagent cost, however good flotation pilot plant results may have been and however well the acute problem of variable feed may be met. The race is on between rabbit flotation and tortoise gravity methods and a surprising amount of betting money is being laid on the tortoise which already is showing previously unsuspected talent for speed. Mostly, however, a wait-and-see attitude prevails during the present preliminary heats. As evidence of the latter, two magnetic plants are now on the boards for magnetic taconites on the eastern Mesabi to establish a reprieve against the time when nonmagnetic taconites must be addressed. Incidentally, these operations will force the blast-furnace issue on preparation of fine material since a minus-100-mesh grind is contemplated.

Jan 1, 1947

By AIME AIME

THE iron and steel activities of this meeting opened on Monday morning with the steel melting session," with G. B. Waterhouse in the chair and A. L. Feild as vice-chairman. N. A. Zeigler's paper, on "Gases Extracted From Iron Carbon Alloys by Vacuum Melbing," created considerable interest and the discussion in general was most favorable. H. W. Gillett and Louis Jordan of the Bureau questioned the method of analysis for oxygen and C. H. Herty, Jr., and J. M. Gaines, Jr., I , expressed their surprise at the large amount of oxygen with the high ,carbon alloys. Whether the gases found existed as gas in blowholes or as oxide inclusions was also a moot point. A paper by C. D. King, on "Basic Open-Hearth Yields," was an extremely interesting and valuable contribution. It was discussed by C. E.Kinney and A. L. Feild and numerous questions were asked throughout the presentation. Mr. King then presented a critical analysis of the losses together with novel methods of calculating them. A paper by C. H. Herty, Jr., and J. M. Gaines, Jr., on "Unreduced Oxides in Pig Iron and Their Elimination in the Basic Open-Hearth Furnace," followed. The question of silicates and oxides in pig iron created much discussion, notably by Henry Hanson and W. J. MacKenzie, who gave figures on chipping cost as a function of blast-furnace practice.

Jan 1, 1929

By G. Cartaud, F. Osmond

WE have already devoted two previous memoirs to this question. In the first we collated and discussed the existing literature on the subject; in the second, we described the crystalline forms obtained by the reduction, at different temperatures, of ferrous chloride by hydrogen or by zinc-vapor. The conclusion from these researches was that the three allotropic states of iron-a, stable below A2; 19, stable between A2 and A3; and 7, stable above A3-all crystallize in the cubic system. The differences observed were such as are customarily encountered in the crystallographic records of many minerals of which allotropic varieties or isomerides are not known, but did not conform to the ordinary definition of polymorphism. It is, however, improbable that allotropic transformations, which are placed beyond doubt by a series of positive facts, do not involve some changes in the intimate structure. As a matter of fact, the crystals we did obtain were too small to allow of a precise examination, and this might introduce an element of uncertainty in the firm establishment of our conclusions. Professor H. Le Chatelier was even led to think from some of our results that iron could very well be a rhombohedron simulating a cube, and not a true cube, and it will be remembered that the crystalline form of bismuth was for a long time incorrectly regarded as cubic. Allotropy does not, however, necessarily involve such a deduction. Without departing from the cubic system at all, a whole

Nov 1, 1906

US 4,132,635 -In the froth flotation beneficiation of low- grade siliceous iron oxide ore, an aqueous pulp of undeslimed ore is conditioned first with a reagent formed by incorporating a water-soluble polyvalent metal salt into an aqueous solution of sodium silicate and then with oleic acid or other anionic collector and optionally pine 011 or other frother. The conditioned pulp is subjected to flotation to concentrate Iron oxide values in the froth D. C. Yang, assigned to Michigan Technological University Jan 2, 1979 7 pp (209-1 66) Filed 1-1 3-77 (759,094) Drawing below.) [ ] US 4,133,038-In the froth flotation beneficiation of copper sulfide ore or other ores, an aqueous suspension of a mineral sample of uniform grain size and composition is conditioned with a strongly adsorbable collector in an amount which is a fraction of the amount sufficient to create a monomolecular layer on the mineral grains, and the conditioning continued until the entire amount of collector is adsorbed The conditioned pulp is subjected to flotation, the floated particles separated at timed intervals, and the flotation rate coefficient determined. By varying the degree of adsorption in repeated treatments, the dependence of the flotation rate coefficient on the degree of adsorption may be determined A Nieml Jan 2, 1979 10 pp (364-502) Filed 12-7-77 (858,353) Priority Finland, 5-26-75 (75/1,525) Same: British 1,533,723, dated Nov 29, 1978 Same Canadian 1,065,066, dated Oct 23, 1979 US 4,133,746System and method for maintaining substantially steady state conditions in the froth flotation beneficiation of copper ore, molybdenum ore, or other metal ores The mass flow of flotation concentrate from the cell is monitored continuously, and the rate of admission of aeration air into the pulp in the cell is varied inversely with respect to variations in the mass flow control of rougher flotation cells is accomplished with a single valve G W Dopson, assigned to Magma Copper Co Jan 9, 1979 6 pp (209-1) Filed 11- 23-76 (744,306

Jan 1, 1980

By J. J. Beeson

Page I. PrimaRy MineRalization............................................ 356 1. Introduction..................................................... 356 a. Scope of Work............................................... 356 6. Acknowledgments............................................ 357 c. The Bingham Mining District.................................. 357 d. General Geology.............................................. 357 e. The Utah Copper Mine....................................... 376 f. Field and Laboratory work.................................... 376 2. The Quartz-Monzonite.............................................. 377 3. The Pegmatite Veins.....:.•..............................:........ 378 4. The High-Temperiture Veins.........................-.............:379 5. The Early Hydrotherma! Period.:......................'............ 380 6. The Late Hydrothermal Period................................:.... 385 II. Seconuabx EnricuMENT............................................. 386 . 1. Author's Note;..... ;............................................ 386 2. Factors Governing Enrichment.....................................: 387 3. The Enrichment.................................................... 387 4. The Covellite Enrichment.; .:; ; : .:. :..:.............:................ 388 a. The Capping above the Covellite Ores:....:....................... 388 b. Conclusions Drawn. from a Study of the Capping and the Covellite ; Ores....,.............................................:.....,.' 392 c. Covellite Enrichment at Depth......:......................... : : 392 5. The Chalcocite Enrichment...................................... ; 394 a. The Carbonates in the Capping above .the Chalcocite Ores...:..: .. 394 ' b. The Formation of Chalcocite..:.:. :......:..'...........,......' 394 . 6. Secondary Chalcopyrite and Bornite.............................i ..., . 395 111.- Conclusions as to the Formation.oF the ImpoRtant Sulphides in the Disseminated ORes........................................,.......... 400 I. Primary MiNeRalization 1. Intrdtiction a. Scop. e .of Work.. first part bf, this paper deals with the country rock, its pegihatitic, pneumatolytic', and hydrothermal altektions; also, the effect of magnetite on the deposition of the primary chalcopyrite and pyrite.

Jan 1, 1916

By H. H. Waller, C. H. Brehaut

At the Jeffrey mine of Canadian Johns-Manville Co. in Asbestos, Que., automatic batched concrete from surface is placed underground pneumatically for distances of 2500 ft directly into forms or to a second placer for greater distances, through 6-in. pipe of high carbon steel. The use of Celite C-4-C in addition to the usual aggregates achieves greater compressive strengths, lowers cost, reduces segregation, and improves workability and placeability results. Each year 25,000 cu yd of concrete are placed without interrupting production and development work in the mine, making possible a cheaper concrete that can be poured wherever and whenever it is needed. In about 90 pct of the underground openings in the Jeffrey mine concrete is necessary to preserve them in their original sizes and shapes for production. In the remaining 5 pct, the greater portion is united with or without steel support. When large quantities of concrete were forecast for underground use at the Jeffrey mine, preliminary and first hand information regarding pneumatic placing was acquired from articles by Bernhardt and Swanson and visits to their respective mines.

Apr 1, 1956

By P. F. Gnirk, J. B. Cheatham

Single bit-tooth penetration experiments under static load were conducted on six rocks at confining pressures of O to 5,000 psi using sharp wedge-shaped teeth with included angles ranging from 30 to 120° In general, the force-displacement curves for all rocks exhibit an increasingly nonlinear and discontinuous behavior with decreasing confining pressure. The confining pressure at which a rock exhibits a macroscopic transition from predominantly ductile to predominantly brittle behavior during penetration vmies from about 500 to 1,000 psi for the limestones to greater than 5,000 psi for dolomite. The correlation between calculated values of force per unit penetration based on plasticity theory and experimental values is quite encouraging, even at confining pressures as low as 1,000 psi A qualitative correlation between volume of fragmented rock per unit energy input for a single bit-tooth and drilling rate for microbits appears to exist over a confining pressure range of 0 to 5,000 psi. INTRODUCTION Laboratory experiments utilizing a small-scale drilling apparatus have demonstrated that penetration rates are reduced considerably as a result of increasing the confining pressure from atmospheric to a few thousand psi?-3 This undesirable situation can, in general, be attributed to a combination of decreased efficiency of chip removal at the bottom of the borehole, increased rock-failure strength, and a possible change in the mechanism of chip generation and rock fragmentation with increasing confining pressure. To more fully understand the principles underlying the last circumstance, it is the purpose of this investigation to experimentally study the mechanism of single bit-tooth penetration into dry rock at low confining pressures and, in particular, to establish the confining pressure at which the penetration mechanism may undergo a brittle to ductile transition for various rock types commonly encountered in drilling. Confining pressure as used here refers to the differential pressure between the borehole fluid pressure and the formation-pore fluid pressure. EXPERIMENTAL PROCEDURE Using an experimental apparatus previously described: a single, sharp wedge-shaped tool was forced under a "statically" applied load into an effectively semi-in finite dry rock sample subjected to a prescribed confining pressure. To prevent the invasion of the con fining-pressure fluid into the pores of the rock sample during penetration, the exposed surface of the rock was jacketed with a layer of silicon putty.* Electrical instrumentation incorporated into the apparatus yielded a graphical plot of force on the tool as a function of penetration or displacement of the tool into the rock during an experiment. During the course of the experimentation the following conditions were maintained constant: (1) pore pressure — atmospheric (i.e., the rock was dry); (2) temperature — 75F; (3) rate of loading — essentially static (approximately 0.002 in./sec); (4) bit tooth — a sharp wedge-shaped tool loaded normal to the rock surface; (5) rock surface — smooth and flat; (6) drilling fluid — hydraulic oil; and (7) maximum depth of penetration — approximateiy 0.1 in. In addition, each experiment was performed on a different rock sample so the rock surface is free of a layer of cuttings and of any previous indentation craters. The influence of the corners of a borehole was neglected, since each rock sample was cemented inta a section of aLuminum tubing to simulate a semi-infinite body. Indentation experiments were made on a sandstone, two limestones, a marble, a dolomite and a schist with a 60' bit-tooth over a range of confining pressures from atmospheric to 5,000 psi and at a constant confining pressure of 1,000 psi for a variety of bit-teeth with angles ranging from 30 to

Jan 1, 1966

By W. F. Boericke

AT Kellogg, Idaho, J. Fred Johnson is driving the 5000.-ft Hooper Tunnel under contract for the Bunker Hill & Sullivan Mining Co. This was visited by a group of engineers during the recent meeting of the A. I. M. E. at Spokane, who were impressed with several features of the work. An excellent record of advance is being made by the contractor, over 47 ft. being driven in 3 days during October, and 223 ft. advanced in 29 shifts. The size of the tunnel is 8 by 9 ft. The ground is Wallace quartzite and, save for the first hundred feet, stands well and does not require timbering. The grade is held uniformly at 0.5 per cent. Two shifts are employed, with two sets of machine men to the shift. Ingersoll-Rand S-70 drills are used. each machine being set up independently in the heading; 26-30 holes are drilled to the round; using 1 1/4: in. round hollow drill steel. A 7-hole cut is required, and these holes are blasted simultaneously, using 60 per cent gelatine, 12 sticks to the hole. Instantaneous and fire delays of electric detonators are used for the complete round. A feature of the drilling is the use of long carriage drills, necessitating fewer changes of steel, and more time spent on drilling, with less time consumed taking steel back and forth from the face. Of course, this means better blacksmithing so that the drill steel shall stand up for the added footage.

Jan 1, 1930

By Edgar L. Weinberg, W. Horatio Brown

The Austinville-Ivanhoe lead-zinc deposit occurs in the Lower Cambrian Shady dolomite. This deposit is located in southwestern Virginia in the faulted and folded Appalachian Valley and Ridge province. The ore bodies resemble the chimmey and manto deposits of northern Mexico and are formed by replacement and filling. They are confined to certain favorable zones of the Austinville and Ribbon members of the Shady. Structural and stratigraphic factors combine to control the location and form of the ore bodies. In certain places secondary oxide enrichment of the zinc minerals has contributed to the economic development of the area. It is concluded that the ore is epigenetic and is deposited by hydrothermal solutions rising through the fault "plumbing." Classification is epithermal-telethermal.

Jan 1, 1968

By H. E. Gross

A plausrsle method of drilling beyond the continental shelves is set forth with limitations of the method. The continental shelves comprise the water-covered portions of land masses out to 600 ft. of water, or roo fathoms. The problems and possibilities of drilling beyond this depth are discussed in this paper. Introduction Much attention is being given the problem of developing petroleum beneath the open sea. Geophysical surveys have been made 26 miles offshore1 from the continental United States, and onco offshore ownership is established it is likely that there will be drilling for oil on the continental shelves. More than two years ago the author presented the means for drilling in deep water.2 at the fall meeting of the Petroleum Division of the AIME at Los Angeles. His concepts then were based on the use of rigid foundations suitable for drilling in water up to 600 ft. deep. The present paper suggests a method for drilling in deeper water. Possibilities and Problems of Drilling beyond the continental shelves It being conceded that because restricted deep-water portions of the hydrosphere might contain oil in commercial quantities, and that at any rate it is pertinent to know more of the nature of the lithosphere beneath the hydrosphere, the possibilities and problems of drilling beyond the continental shelves should be set forth. Drilling in open water would offer few if any advantages over drilling on land. These are: 1. The ocean transportation is available to deep-water drilling sites, and extensive pipe lines and roads are unnecessary. 2. Refinery facilities and markets perhaps are established on the near-by shore where adjacent fields on land are nearing depletion. 3. There is freedom from jungle pests and tropical diseases. 4. Competitive drilling is less likely. 5. Extensive areas attractive for development arc not yet under lease or concession. Disadvantages are great and numerous: 1. Storm hazards from wind and wave. 2. Expensive foundations, either rigid or floating. 3. Shutdown times because of weather. 4. Marine Regulations of Federal Bureaus in addition to customary regulations on land. 5. Frequent difficulty in moving men and materials to and from drilling platforms. 6. Extra precautions required in open sea. For drilling in water more than 500 or 600 ft. deep, rigid foundations2 become too costly, and floating foundations must be used, and they must meet the following requirements:

Jan 1, 1947

By H. E. Gross

A plausrsle method of drilling beyond the continental shelves is set forth with limitations of the method. The continental shelves comprise the water-covered portions of land masses out to 600 ft. of water, or roo fathoms. The problems and possibilities of drilling beyond this depth are discussed in this paper. Introduction Much attention is being given the problem of developing petroleum beneath the open sea. Geophysical surveys have been made 26 miles offshore1 from the continental United States, and onco offshore ownership is established it is likely that there will be drilling for oil on the continental shelves. More than two years ago the author presented the means for drilling in deep water.2 at the fall meeting of the Petroleum Division of the AIME at Los Angeles. His concepts then were based on the use of rigid foundations suitable for drilling in water up to 600 ft. deep. The present paper suggests a method for drilling in deeper water. Possibilities and Problems of Drilling beyond the continental shelves It being conceded that because restricted deep-water portions of the hydrosphere might contain oil in commercial quantities, and that at any rate it is pertinent to know more of the nature of the lithosphere beneath the hydrosphere, the possibilities and problems of drilling beyond the continental shelves should be set forth. Drilling in open water would offer few if any advantages over drilling on land. These are: 1. The ocean transportation is available to deep-water drilling sites, and extensive pipe lines and roads are unnecessary. 2. Refinery facilities and markets perhaps are established on the near-by shore where adjacent fields on land are nearing depletion. 3. There is freedom from jungle pests and tropical diseases. 4. Competitive drilling is less likely. 5. Extensive areas attractive for development arc not yet under lease or concession. Disadvantages are great and numerous: 1. Storm hazards from wind and wave. 2. Expensive foundations, either rigid or floating. 3. Shutdown times because of weather. 4. Marine Regulations of Federal Bureaus in addition to customary regulations on land. 5. Frequent difficulty in moving men and materials to and from drilling platforms. 6. Extra precautions required in open sea. For drilling in water more than 500 or 600 ft. deep, rigid foundations2 become too costly, and floating foundations must be used, and they must meet the following requirements:

Jan 1, 1947

By AIME AIME

PETROLEUM technology was the sole subject of discussion at the meeting of the Petroleum Division at the Baker Hotel, Dallas, Texas, Oct. 6-7, except for the brief talks by President Becket and Secretary Parsons at the dinner on Friday evening. Even on this occasion, following the scheduled official features, it was in order to talk "shop." W. E. Wrather and E. A. Stephenson, respectively Chairman and Secretary of the Division, had planned for a meeting of this nature and by preference, apparently, the 122 who registered fell in with the scheme wholeheartedly. Not because the competent local committee had not provided for it, but by choice, the members just did not sign up for entertainment or field trips, but did attend largely the three technical sessions and engage in earnest discussion of the approximately dozen excellent papers. In this connection, and without question, the high lights of the meeting were the papers by Morris Muskat and R. D. Wyckoff, and Prof. W. K. Lewis. The former, entitled, "A Theoretical Analysis of Waterflooding Networks," had been entirely demathematized by the authors for presentation at this and the Los Angeles meetings; the author of the latter, which was on the "Physical-chemical Relationships of Hydrocarbon Gas-liquid Mixtures at High Pres¬sures," had airplaned to Dallas in the company of Dr. H. D. Wilde from Chicago in order to present his paper at the final session on Saturday morning.

Jan 1, 1933

By A. S. Richardson

THE conditions that make necessary the mechanical ventilation of the Butte mines of the Anaconda Copper Mining Co. are due to a number of causes, all of which are incidental to the depth at which mining operations are now carried on. The main object to be accomplished, of course, is the reduction of the temperature and humidity of the air in the working places. Ventilation fans, both surface and underground, have been used for many years, but increasing depth has made the problem much more difficult. Further improvement in both ventilation equipment and methods, therefore, became necessary; and it is the purpose of this paper to describe the work planned and done under the improvement program. The mines of the district have been frequently described in various technical publications, so a description is unnecessary here. From a mine-ventilation viewpoint, compared with coal-mine ventilation systems, the problem is complicated by the fact that the workings to be ventilated are situated on a large number of steeply dipping veins which frequently intersect and are faulted, and also by the fact that the extent, or existence, of orebodies is not definitely known in advance of actual development work. For these reasons ventilation work cannot be planned in advance of actual operations, nor can such regular systems of ventilation as are used in working the more uniform and continuous bodies of coal be developed. When operations are conducted at a normal rate, about 10,000 miners are employed on two shifts, so that about 5000 men will be underground at one time. But as ventilation is necessary to reduce high temperature and humidity due, mainly, to natural causes, the quantity of air per man per minute is not a governing consideration in determining ventilation requirements. Most important among the numerous sources of heat and humidity in the mines are : heat generated during decay of mine timber; heat and humidity given off by mine rock and water; heat generated by oxidation of sulfide minerals; heat given off by electrical equipment; heat generated by mine fires (in certain localities).

Jan 2, 1922

By Shiou-Chuan Sun

THE fact that coals of different ranks and even of the same rank differ greatly in their amenability to froth flotation is well known. In recognition of the need for an explanation of this phenomenon, two hypotheses have been suggested. Wilkins1 reported that the floatability of coals increased with an increase of the carbon content or rank. This postulate is handicapped by the fact that bituminous coals that possess moderate carbon contents are actually more floatable than anthracite coals that have high carbon contents, as shown in columns 6 and 9 of Table I. Taggart and his associates' implied that the difference of floatability between bituminous and anthracite coal was caused by the variation of carbon-hydrogen ratio. This is not applicable to the relative floatability of other coals and carbons. For example, column 11 of Table I shows that the carbon-hydrogen ratios of low-floating lignitic coal and non-floating animal charcoal are not only smaller than the moderate-floating anthracite coal, but are also similar to the high-floating bituminous coal. Furthermore, according to this hypothesis, high temperature coke-A (464), Ceylon graphite (1238), and lamp-black (357), all possessing extremely high carbon-hydrogen ratios, should be less floatable than other substances having much lower carbon- hydrogen ratios such as high volatile-B bituminous coal (11.9 to 22), anthracite coal (35.7 to 60.5), lignitic coal (15.6 to 33.6), and charcoal (13 to 26.2). However the former group is actually more floatable than the latter group.

Jan 1, 1954

By L. C. WYMAN

THIS paper discusses what mining reports should contain when presented to the California State Corporation Department, to accompany applications for the sale of stock to the general public, but the principles involved apply to mine financing everywhere. Such reports should 'be as clear and concise as possible, endeavoring to tell the truth in as few words as necessary. Should the engineer be aware that his report is to be used in connection with the sale of stock to the general public, he should consider the public as his client as well as the person who actually employs him. It is always required that the engineer be favorably known and of recognized standing. The following points should be given careful attention : 1. A legal description and location of the property. 2. Transportation conditions, and how they may be expected to affect the operating costs. 3. A brief history of the property, its production record as to tonnage, grade, and character of the ore should be given. Should the property have suspended operations for any reason, this should be given. Any details of former operating costs should be given, especially as to how any improvement could be made, due to better methods which might be employed.' 4. The main geological features and whether they are such as to lead the engineer to believe that the mine may possibly 'be exhausted or the ore of such grade as to be no longer profitable. If he considers them favorable, he should give his reasons for the belief that further development work may produce profitable results. A map showing these features should be submitted, and it is not necessary that such map be highly colored or contain any more than the essential matters. 5. Other mines in the district, or those with similar

Jan 1, 1929

By AIME AIME

THE Institute of Metals held a well rounded out symposium on the working of metals, distributed over two sessions. At the first session* four papers were presented, two dealing with the, cold working of metals and alloys and two with the hot working of non-ferrous alloys. The first paper by E. V. Crane, dealt with "Metal Working in Power Presses." Mr. Crane pointed out the empirical nature of engineering data available for use in calculating the probable stresses developed and power requirements, for the shearing, drawing, binding and other forming operations. He described the various operations, methods of determining stresses developed and presented data obtained. In the discussion C. F. Hammond took exception to Mr. Crane's objections to the rather too frequent. annealing operations in drawing of cartridge cases, pointing out that the material was-manufactured to meet specified structure and physical requirements, which could only be met by carefully controlled sequences of working and intermediate annealing operations.

Jan 1, 1931

By RALPH HAYES SWEETSER

IRON ore and bituminous coal are the two basic raw materials for the whole iron and steel industry. The ore furnishes the iron and is absolutely necessary-all iron and steel products come directly or in- directly from the iron ores. The bituminous coal furnishes the carbon needed for the smelting of the ores and for the fuel used in all the processes of iron and steel manufacture. The necessary carbon could be furnished in some other form besides bituminous coal. In fact, it is only since the Civil War that bituminous coal has been the chief source of the carbon for metallurgical fuel. For many years only charcoal made from the forests furnished the carbon for smelting iron ores. About 90 years ago, anthracite coal was first used as blast-furnace fuel and for many years continued to be the chief blast furnace and steel making source for carbon. Even in my own blast-furnace experience, I have used charcoal in Canada and anthracite in Pennsylvania for smelting ores in an iron blast furnace. Bituminous coal, now almost exclusively the source for the carbon used in smelting iron ores, also furnishes most of the heat used in the steel-making processes. It is seldom used in blast furnaces in its natural condition, hut is first coked in beehive, or in by-product coke ovens; such bituminous coal is called "coking coal." Bituminous coal that is suitable for making the producer gas used in the open-hearth steel process is called gas coal. Any bituminous coals suitable for making blast-furnace coke or foundry coke, or that can be satisfactorily used for making producer gas, are classed as metallurgical coals and as such are to be considered in my proposed plan for the evaluation of metallurgical coals. According to Bureau of Mines Bulletin No. 449 these coals comprised 22 per cent of the bituminous coals mined in this country in 1923.

Jan 1, 1926

By H. T. Hildage

ALTHOUGH Greater New York does not bear any resemblance to a great mining district, the mining operations that are being conducted in and about the city are both extensive and interesting in character. With regard to the extent, it may be mentioned that, at. present, there is more dynamite used in New York than in any mining district in the United States; that there are under construction about 38 miles of tunnel, and that 66 miles more are projected, most of which must be constructed in the near future ; that since 1902 at least 2,000,000 tons of earth has been removed in underground work, in addition to about 3,500,000 tons that has been removed in, open-cut in connection with tunnel-work, and many times this quantity that has been removed in excavating foundations for buildings not connected with tunnel-work; and that there are to-day probably more than 5,000 men engaged in mining-work in and about New York City. These undertakings include almost every operation connected with underground work, from exploration by means of trench and boring, to the sinking of large shafts and the driving of large tunnels through every kind of ground from hard rock to soft, semi-fluid silt and quicksand. It is proposed in this paper to give a general description of some of the methods and appliances used in the opening-up ,of a "mine" in a large city, and a brief description of some of the "mines" now being developed in New York, connecting as far as possible the methods described with the particular work for which they were designed, in order to give a general idea of the

May 1, 1907

By W. B. Plank

RETURNS already received from a current survey of the enrolment of students in the mineral technology schools indicate a degree of activity and prosperity in those schools never before equalled. The returns are as yet too meager for accurate analysis, but those at hand point LO considerable increase in the metallurgical and petroleum engineering groups, and indicate that the total of 5011 two years ago in the United States schools will be substantially increased. Generally speaking, the enrolment is not only maximum in quantity but optimum in quality. Better income has sent the boys back to school, but the improved employment conditions have somewhat reduced the number of graduate students. Laboratories are commonly filled to capacity, in some instances overcrowded. Increased enrolment of foreign students from both Canada and South America is noticeable.

Jan 1, 1937