Search Documents

By B. Weyerman

U. S. Steel's Oak Grove Mine experienced several top hinge failures on their caving shields. It was determined that all the caving shields needed to be replaced with new caving shields before more thilures occurred. The cost and amount of time needed for several scenarios of caving shield change outs were compared. This paper discusses how Oak Grove Mine decided to and did change 126 caving shields in six specially designed jig stations underground during a longwall move using their own UMWA employees.

Jan 1, 2001

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modifying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel, et al., 1997) to: identify and quantify operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project was completed in 1998.

Jan 1, 1999

By Malcolm Ross

The Reserve Mining Co., in the processing of taconite iron ore quarried from the Peter Mitchell Pit, deposited the finely crushed waste rock into Lake Superior near Silver Bay Minnesota. In the early 1970s The U.S. Environmental Protection agency filed a lawsuit against Reserve Mining Co., asking the court to force the company to stop dumping into the lake. On April 20, 1974, after a lengthy court battle, the U.S. District Court concluded that the Reserve Mining discharge into Lake Superior violated federal and state pollution laws and thus ordered Reserve Mining Co., to halt the lake disposal of taconite tailings. At the time many feared that some of the mineral particles contained in the tailings (alleged to be asbestos or asbestos-like) would cause human health problems. This Conference was thus convened to readdress the problem of the mineral content of the Biwabik Iron Formation and to whether any minerals contained in the ore could cause human disease. The four papers given in this session address the nature of the mineral particles in the taconite rock, the definition of the term ??asbestos?? and the history of the legal controversy over the possible health effects of certain mineral particles contained in the Biwabik iron range ores. Paper 1?Geology of the Biwabik Iron Formation and Duluth Complex Mark A. Jirsa, James D. Miller, Jr., G.B. Morey The Biwabik Iron Formation was a principal source of ore for the American steel industry during the 20th Century. The unaltered iron deposits, called taconite, contain approximately 30% iron and 50% SiO2. About 75% of the iron in taconite resides in the mineral magnetite, the remainder is largely in iron carbonate and several iron-silicate minerals.

Jan 1, 2007

By John J. Stetler

Introduction Samarco Mineracao S.A. is a Brazilian corporation jointly owned by S.A. Mineracao da Trindade (SAMITRI) and Utah International Inc., with 51% and 49% interests respectively. Headquartered in Belo Horizonte in the state of Minas Gerais, Samarco owns and operates an open-pit mine capable of producing 10 Mt/a (11 million stpy) of iron ore; a concentrator rated at 7 Mt (7.7 million st); a 12-Mt (13.2-million st) capacity pipeline transportation system; a 7 Mt (7.7 million st) filtering and pelletizing plant; and a harbor facility. The mine, concentrator, and initial pipeline pump station are located at Germano, near the town of Mariana, about 300 km (186 mi) north of Rio de Janeiro by air. The pipeline terminal, pellet plant, and harbor are at Point Ubu, 70 km (43 mi) south of Vitória the capital city of Espirito Santo State, and about 300 km (186 mi) by air east of the mine. The 396-km (246-mi) pipeline uses 508-mm (20-in.) pipe except for a 53-km (33-mi) section where 457-mm (18-in.) pipe is used to absorb and control slack flow through increased velocity in one of the areas along the route. Iron Ore Slurry The hematite iron ore concentrate produced at the Germano plant is processed by grinding the average 53% run-of-mine itabirite iron ore to -150 µm (100 mesh) for gangue liberation. It is treated further by cyclones to remove the 10 µm (1250 mesh) slimes to prepare the ore for flotation. During the multistage cationic flotation operation, the silica is reduced to make low silica (-0.9%) concentrate for the direct reduction (DR) iron-making process or to make normal silica (-3.5% +2.5%) concentrate for the blast furnace (BF) iron-making process. The concentrate then is reground further to meet the particle size requirements for pelletizing. The reground hematite concentrate is screened in closed circuit with the regrind mills for close control of the maximum particle size, not to exceed 3.5% +75 µm (200 mesh) for pipeline wear protection. Thickened concentrates at 70% solids are pumped to four 5-kt (5,510-st)(dry) agitated slurry storage tanks that hold the feed before it goes to the first pipeline system pumping station. Pipeline Capacity The pipeline system was designed to transport 12 Mt/a (13.2 million stpy) at 65% solids with an average minimum safe operating velocity of 1.5 m/s (5 fps). The pipeline will transport 5 Mt (5.5 million st) in 1982. The system, therefore, is moving the slurry in 13-kt (14,330-st) batches, dispatched at intervals to move 20 kt/d (22,050 stpd). In operation, the pipeline has exceeded its 93% availability design factor. Pipeline Facilities Pump station No. 1 is located at the Germano minesite 1 km (3,330 ft) above sea level. It has the following principal equipment: • four 5 kt (5,510-st) (dry) agitate slurry storage tanks; • two centrifugal charge pumps (one stand-by); • a 217-m (712-ft) safety loop; • seven mainline positive displacement triplex plunger pumps (189 m3/h, or 832 gpm, at 14.9 MPa, or 2,162 psi, maximum output pressure); • four corrosion-erosion spools; • a control and command center. Operation The output at pump station No. 1, with 66% solids, is pumped 151

Jan 10, 1982

By J. D. Morgan

In the first half of the year, lessening of cold war tensions was welcome. But Iraq's invasion of Kuwait in the second half led to the Persian Gulf War in January and February 1991. This caused an oil shock that dampened the economy. So the US gross national product rose only 0.9% to $5,463 billion (US billion = 109). The buildup of military forces in the Persian Gulf area focused greater attention not only on petroleum but also on other strategic materials. The Department of Defense continued to review stockpile goals and to upgrade several mineral materials. In addition, the Bureau of Mines continued to maintain the standby Emergency Minerals Administration. The Defense Production Act, which authorizes priorities, alloca¬tions and supply expansion, lapsed on Oct. 20. So the Selective Service Act of 1967 became the authority for assuring that orders of the armed forces and defense atomic-energy programs were given priority treatment. Consumer demand strongly affects mining worldwide. US citizens carry significant debt, and large stocks of housing and consumer goods are already in place. Some 250 million persons have 188 million licensed motor vehicles and 100 million dwelling units. Consequently, new car production fell 11 %, to 6.1 million units. Truck and bus production fell 8%, to 3.7 million units and new private housing starts fell 13% to 1.2 million units.

Jan 1, 1991

By L. J. Blatnica

Throughout the 1980's the tem Mine-Wide Monitoring System has had various meanings for manufacturers of these systems and underground mine operators alike. System suppliers had visions of grandeur in the early 80's as they envisioned each mine, that has more than a single section, installing a computer based monitoring system to provide surveillance, control and documentation of the entire mining operation, including everything from a single heat detector to the weekly payroll. In a few cases this may have become reality but the truth is these systems have quietly become a steady but unspectacular workbase for the modern mining industry of the 1990's. As it exists today the total market for underground monitoring systems may not exceed $10 million annually. Suppliers have lowered their expectations of the dollar value of this particular market. Some were entering a new market because of experience with computer based data acquisition systems. Others had been active in the mining industry for years with more traditional equipment (communication systems, methane monitors, safety equipment, etc.) and decided to become involved with Mine-Wide Monitoring Systems.

Jan 1, 1990

By J. C. Haptonstall

The Bismark Mine is located in northern Chihuahua, Mexico, 150 km (95 miles) southwest of Ciudad Juarez (Fig.1). The ore deposit was discovered in 1979 and was placed in production in 1992. The production rate is about 2.4 kt/d (2650 stpd) from an ore reserve of 8.5 Mt (9.3 million st). Grades currently average about 8% zinc, 0.5% lead, 0.2% copper and 50 g/t (1.46 oz/st) silver. Substantial inflows of water into the underground mine complicate the operation. Complex metallurgy poses another challenge for the operators. Bismark is a joint venture with 90% participation by Minas Penoles, SA de CR of Mexico City and 10% participation by Promociones Industriales Banamex, S A de C V (PIB S A) of Mexico City. Anew company, Minera Bismark, SA de CV was formed to operate the property. Cyprus Minerals was a 40% participant in the joint venture but, in early 1993, sold its share to Minas Penoles. The Bismark Mine is one of the largest new underground mining projects built in Mexico during the last 10 years. It is the country's fifth largest underground metal mine and provides about 1 % of the world's zinc supply at about 50 t/a (55,000 stpy). Bismark is a trackless operation with overall productivities of 7.6 t/manshift (8.4 st/manshift). The 2.4-kt/d (2650-stpd) concentrator started up in March 1992.

Jan 1, 1994

By I. A. Tinto

Labrador City is located in the southwestern portion of Newfoundland-Labrador, approximately 965 kilometers north-east of Montreal. The mine and beneficiation complex of the Iron Ore Company of Canada, known as the Carol Project, is situated 535 metres above sea level in a climatic region characterized by cold winters and short, cool summers. History The iron Ore Company of Canada commenced work in the area in 1949, however, it was not until 1958 that the decision was made to proceed with mining operations. The ore body consists of Specular Hematite (Fe203) and Magnetite (Fe304) with small quantities of Limonite and Geothite. The average grade of the ore bodies is 39% iron.

Jan 1, 1985

By A. Fuerst

The recent seismic events have shown that earthquakes have an immense destructive power. Chile was hit in February 2010 with a seismic intensity of 8.8 on the Richter scale, and had loss of about 700 killed persons, while Haiti was hit in January 2010 with 7.0 killing about 220?000 people. The event in Haiti showed that the seismic events can lead to a disaster if no preventive measures are taken. On the other side, the seismic event in Chile has hit a well-prepared country with moderate consequences. The earthquake with 6.6 Richter in Japan in March 2011, have further shown how severe the consequences can be if critical equipment is involved. Fortunately, the equipment in a mine has not the potential hazard as a nuclear power plant. Anyway, we are diligent and it is obvious that the seismic risk may lead to a real disaster even if the probability is small. The GMD is an important component in the grinding circuit of a mine. This paper maps out earthquake-prone areas including expected earthquake magnitude calculated according to relevant standards, focusing mainly on the building code IBC 2009. An overview is provided on how this standard is applied to mining equipment to minimize damage and aid large mills in operation to successfully withstand seismic effects. The differences in stresses and forces on the GMD and foundation are shown based on a turning and stopped mill simulation during an earthquake. The results demonstrate the need to maintain active and operating earthquake detection systems. Aside from detecting an earthquake?s magnitude, the sensor information can also be used to reduce the harmful effects that an earthquake has on mining equipment. As follows the earthquake requirements are defined. The last part of this paper explains how to fullfill these requirements.

Jan 1, 2012

By V. Svalbonas, S. M. Jones, A. Boughey

In June 1998, the world's largest grinding mill, the 40 ft (12.2 m) diameter 20 MW Cadia gearless SAG mill, was commissioned. This was a leap of over40% above the largest operating SAG mill. A significant saving in capital cost gave the incentive necessary for a single mill line at Cadia, resulting in the selection of the 40 ft (12.2 m) diameter mill. Now, after 18 months of operation, this paper will review the significant items involved in the development, design, manufacture, installation, and operation of this mill.

Jan 1, 2000

By Richard F. Flanagan, Robert H. Marshall

The Republic of Singapore’s Public Utilities Board is implementing the Deep Tunnel Sewerage System Project. The project’s deep tunnel component, 48 km of deep, large diameter sewer tunnels has been successfully completed (the works are in the defects liability period). Six International Design/Build tunnel contracts utilized eight Earth Pressure Balance TBMs ranging up to 7.23 m in diameter to deal with varied ground types ranging from deep soft clays to fresh granite. Numerous access/workshafts were constructed and using various support systems. This paper provides an assessment/overview of the tunnel contracts, tunnel excavation methods and equipment, and the shaft systems. Suggested enhancements to similar future projects are provided.

Jan 1, 2007

By Harry R. Price, Behrooz Tahmasbi, Charles J. Roarty

The 2,408 meter (7,900-foot) long Middle Rouge Parkway Interceptor Extension varies in size from 1.52-meter (5-foot) to 2.36 meter (7-foot 9-inch) inside diameter. Most of the sewer was constructed in tunnel through fine sands and silts. Piping of these soils through the concrete liner eventually resulted in a loss of soil support, settlement and/or severe distress of the sewer, and the formation of several sinkholes. The repair and restoration was generally performed in the sewer and included cast-in-place concrete, shotcrete, cured in place pipe, soil stabilization, cement grouting, dewatering, and chemical grouting. As a part of the work, temporary pump stations and flow diversions were required to perform the work while minimizing discharges to the adjacent Rouge River.

Jan 1, 2007

By John Hanna

The Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of phosphate minerals from siliceous ores. The process takes advantage of preferential adsorption and high reactivity of fatty acid collectors towards apatite over silica surfaces under slightly acidic conditions of pH 5-6.5. The process was successful in upgrading various phosphate samples from Florida and North Carolina containing 7.7-15.3% P205 and 62.3- 77.2% Insol to concentrates assaying 28.1-33.1 % P205 and 4.1-9.9% Insol with high P2O5 recovery of 81.8-92.2%. Depending on the type of silica impurities present one or more cleaning steps, with or without sodium silicate, would be required to improve the grade of the rougher phosphate concentrate.

Jan 1, 1992

By Shane Yanagisawa

The Mineral Creek Diversion Project is at the Asarco Ray Mine Complex, about128 km (80 miles) east of Phoenix, Arizona. The new tunnel will intercept the waters of Mineral Creek about 2,134 m (7,000 ft) upstream from an existing tunnel. The 5.74 m(18.83 ft) hard rock TBM will break into the old tunnel about 2,162 m (7,090 ft) in from the old portal after mining 3,888 m (12,753 ft). The TBM will mine through a series of igneous and metamorphic formations including volcanic tuff, soft volcanic ash, massive diabase, fractured quartzite, and schist. The TBM will hole through into the existing 4.88 m (16 ft) dia. horseshoe tunnel where the TBM will be disassembled and removed from the tunnel.

Jan 1, 2001

By D. K. Jorgensen

The Bullfrog and Montgomery-Shoshone deposits, near Beatty, NV, have a combined drill-indicated reserve of 15.8 Mt (17.4 million st) of ore. Average grade is 3.5 g/t (0.103 oz per st) gold and 8.2 g/t (0.24 oz per st) silver. The deposits occur in Miocene volcanic rocks that underwent large-scale movement within a detachment-faulted terrane. The principal host to gold mineralization is a strongly welded rhyolitic tuff that experienced brittle deformation during plate movement. Open space fractures and breccia were filled with quartz, calcite, and adularia accompanied by lesser pyrite, gold, and acanthite. Gold occurs as micrometer-sized particles within and adjacent to the low-angle fault and along associated listric-normal and tear faults. The Bullfrog and Montgomery-Shoshone are volcanic-hosted, detachment fault-related, epithermal quartz calcite stockwork gold deposits. Bullfrog's minable reserve is 13 Mt (14.3 million st) of ore grading 3.8 g/t (0.11 oz per st) of gold. At Montgomery-Shoshone, 2.7 Mt (3 million st) minable tons at 2.5 g/t (0.072 oz per st) are present. Preproduction stripping has begun at the Bullfrog ore body. A 7.7-kt/d (8500-stpd) carbon-in-pulp (CIP) mill is under construction. In 1990, Bond Gold expects to be producing about 6.2 t/a (200,000 oz per year) of gold.

Jan 1, 1990

By Christopher J. Bise

INTRODUCTION A mine's power system represents the driving force behind all of the extraction and auxiliary operations, because the production and transportation of mined material and the operation of equipment, such as fans and pumps, are all dependent upon a power source. Once, compressed air was the primary power source in mining; today, however, electrical power dominates. This chapter reviews the basic theories of com- pressed-air and electrical power and provides several examples of applications in mine power systems. COMPRESSED-AIR POWER General Compressed air has been, and should continue to be, an important source of power in mining operations. It has been used as a means of blasting coal in conventional mining and is widely used to operate stopers, mucking machines, and other air tools in both coal and hard-rock mines. Such applications demonstrate the suitability of compressed air for applications requiring linear motion, but it is also utilized for its reliability and safety. A compressed-air system is composed of a compressor, a receiver, a distribution network, and the air-operated machines. A compressor takes in air at normal atmospheric pressure (free air) and compresses it to a higher discharge pressure. The discharge pressure must be high enough to overcome the friction in the distribution system of pipes and hoses and deliver the compressed air to the machines at the pressure recommended by the manufacturer. The most common type of compressor used in mines is the reciprocating compressor in which the air is compressed by a piston in a cylinder. An air receiver is a container or storage tank that is located in the distribution system between the compressor and the machines. It stores compressed air, when the full capacity of the compressor is not being used, and gives a more steady flow of air to the machines. The distribution network consists of pipes, Oalves, elbows, tees, and hoses that transmit the compressed air from the receiver to the machines in the mine. It is essential that the distribution system be designed with the proper sizes and lengths of pipe, hose, and other components to keep pressure losses well within allowable limits. The air-operated machines consist primarily of drifters, stopers, pluggers (sinkers), slushers, and several other pieces of equipment. Compressor Operation Every compressor is made up of one or more basic elements; a single element, or a group of elements in parallel, comprises a single-stage compressor. Many compression problems involve conditions beyond the practical capability of a single compression stage. Too great a compression ratio (absolute discharge pressure divided by absolute intake pressure) may cause excessive discharge temperatures or other design problems. It, therefore, may become necessary to combine elements or groups of elements in series to form a multi- stage unit, in which there will be two or more steps of compression. The number of stages commonly used in reciprocating compressors is as follows: Pressure Number of stages 0- 150 pig 1 80- 500 psig 2 500-2500 psig 3 2500-5000 psig 4 When pressure is referred to as pounds per square inch gage (psig), it means the pressure (in pounds per square inch) above barometric pressure as measured by a gage. The sum of barometric pressure and gage pressure is the absolute pressure (in pounds per square inch). The gas is frequently cooled between stages to reduce the temperature and volume entering the subsequent stages, thereby reducing the work required for compression. The basic reciprocating compression element is a single cylinder compressing on only one side of the piston (single-acting). A unit compressing on both sides of the piston (double-acting) consists of two basic single-acting elements operating in parallel in one casing. The reciprocating compressor uses automatic spring-loaded valves that open only when the proper differential pressure exists across the valves. Intake valves open when the pressure in the cylinder is slightly below the intake pressure. Discharge valves open when the pressure in the cylinder is slightly above the discharge pressure. In Fig. 1, Diagram A shows the basic element with the cylinder filled with air at atmospheric pressure. On the corresponding theoretical pressure-volume

Jan 1, 1986

By Helmut Hass, Michael B. Gilbert

The extension of the commuter railway system (S-Bahn) in Leipzig, Germany willrequire the construction of an underground line crossing the downtown area of thecity to tie the Bavarian Station in the South to the Main-Station in the North. The City-Tunnel-Leipzig is currently one of the largest infrastructure projects in Europe. This system extension will have a length of approximately five kilometers. 3.9 kilometers of that length are currently being constructed using either cut & cover construction or tunnelingmethods. The design and construction of this project currently is and will continue facing very significant challenging urban and demanding geotechnical conditions.

Jan 1, 2007

By J. Kretschmann

Around the world, mining has been done for thousands of years for the benefit of humankind. The winning process in mining operations ends with the depletion of the deposit or its closure if the operation becomes economically unprofitable. After that, a period of post-mining follows which may last for a very long time and which is generally regarded as a period of hazards, risk and high cost. In the USA alone, approximately 500,000 abandoned mines do exist; worldwide, there are millions. In Germany, too, we have had to deal with abandoned mines for a considerable period of time now.

Jan 1, 2012

By Y. P. Chugh

Additional field evaluations of a modified continuous miner using a new spray system and modified scrubbers have been conducted by the authors. In this demonstration, a comprehensive package for dust control on a continuous miner which included previously developed modifications to the scrubber, scrubber intakes and the innovative chassis spray system was demonstrated. Side-by-side comparisons of the modified miner and regular miner indicated that the miner operator with the modified miner was exposed to 62% less respirable dust. Ram car operators with the modified miner had 38% less respirable dust exposure and the return air on the modified miner had 19% less respirable dust. The mining conditions during side-by-side testing were very comparable. These results support the findings of the modified spray system studies conducted earlier at different mines in Illinois on four occasions and the modified scrubber system field evaluation studies.

Jan 1, 2009

By N. Loganathan, Tan Boon Tee, Joe O’Carroll, Richard Flanagan

In recent years, tunnelling activities in Singapore have increased considerably with the construction of extensions to the existing sub-surface transport system, a deep tunnel sewerage disposal system, and tunnels for the laying power cables and other utilities. These tunnels are excavated through urban areas, adjacent to high-rise buildings, depressed road structures, beneath other tunnels, and buried services. Earth pressure balance (EPB) tunnel boring machines (TBM) have been used extensively in Singapore with great success. The risk associated with soft ground tunnelling, including tunnelling through Old Alluvium, can be minimized with an understanding of the geology, geotechnical parameters, and the tunnelling-induced behaviour of Old Alluvium (OA The purpose of this paper is to present some design and construction aspects of EPB TBM tunnelling through Old Alluvium.

Jan 1, 2005