Search Documents

By Robert P. King

In April, 1975 the Colorado School of Mines began monitoring rock mass response associated with a long- wall shield demonstration project near Raton, New Mexico. This project was sponsored by the U. S. Bureau of Mines (DOE) and performed at Kaiser Steel Corporation's York Canyon Mine. Two of the results of the intensive instrumentation effort are the empirical subsidence and horizontal strain models presented herein. These models are based on data gathered during mining three adjacent longwall panels (4N, 5N and 6N). A total of 251 permanent surveying monuments were monitored over the three-panel area. Lines of monuments were oriented along panel centerlines, perpendicular to centerlines and diagonal (45O) to centerlines. Active monuments were monitored twice a week, with less frequent monitoring of stable or slow moving monuments. Primary subsidence monitoring equipment consisted of an AGA Geometer Model 75 and a Wild T-2 Theodolite with -a Wild-Sercel DI-3S distomat.

Jan 1, 1979

By L. M. Gochioco

The U.S. coal industry is under-going dramatic changes to meet the challenges of the keenly competitive fuels market. The application of innovative technologies is needed to improve safety and to increase productivity in order to make coal more competitive as a fuel. As more coal companies shift into capital intensive longwall mining, there is a clear need to invest more in exploration before mine plans are made. Coal seam anomalies may create adverse mining conditions. The early detection of these anomalies could make the longwall mining safer and more productive through improved planning. A standard exploratory drilling program can provide only limited geologic information. The seismic reflection technique can be used to detect coal seam anomalies and is effective in reconnaissance surveying. Recent advances in the quality of coal seismic data have increased the success rate of seismic surveying. Therefore, surface seismic surveys, coupled with selective drilling, will come to play an integral role in coal exploration in the 1990s.

Jan 1, 1990

By Sam H. Patterson

The advances in knowledge of world bauxite resources in the last few decades include contributions to the geology of deposits, discovery of large resources, shifts in availability, and changes in. the industry in response to political and economic pressure. Improvements in the understanding of geology have resulted from the larger numbers of geologists working on bauxite and better exchanges of information. The large deposits discovered are mainly the laterite type in tropical regions. These discoveries have led to major increases in bauxite resource estimates as well as to shifts in bauxite availability and in the ranking of producing nations. Changes resulting from political, environmental, and economic pressures have resulted in increased costs of bauxite and in renewed interest in potential nonbauxite sources of aluminum. Aluminum is produced from nonbauxite raw materials only in the U.S.S.R.; however, research on extraction processes or investigations of nonbauxite alumina resources has taken place in several countries.

Jan 1, 1984

The structure of a mine ventilation network (M.V.N.) can be represented graphically using either the mine plan (map) itself or a number of other types of diagrams. In the U.S., the two most common approaches are the line and the schematic diagrams (see Figures 1 and 2). The purpose of this paper is to introduce another type of diagram, called the canonical diagram (6). The method of M.V.N. representation which uses canonical diagrams is used extensively in Europe, and especially in Poland, where it was developed. The canonical diagram is a noncalibrated topological image of a ventilation system. It gives a simple representation of the ventilation network, allows for the classification of currents within it and enables rapid computer analysis and computation, as well as the representation of the results. It is especially useful in studying and controlling the air flow, and it may be a life saving tool in conducting rescue operations during and after mine fires.

Jan 1, 1986

By J. A. Marts, R. C. Gilmore, S. Saki, J. F. Brune

Computational fluid dynamics (CFD) modeling involves the creation of a computation domain called a mesh or grid to solve the equations defining the physics of fluid flow. This process often comprises the majority of time spent in modeling efforts. In a project sponsored by the U.S. National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines used an innovative meshing approach, allowing easy adaptation of the CFD model to adjust to a variety of longwall bleeder-ventilated and progressively sealed (often referred to as bleederless in the United States) mining geometries, with gob porosity and permeability scalable over a wide range. This paper presents the methodology of the meshing and scaling approach along with recommendations for using CFD modeling in longwall gob ventilation applications. The new meshing technique was utilized to evaluate the function of a back return in a progressively sealed gob and a bleeder-ventilated gob.

Jan 1, 2014

By R. A. Winters

At the operations level, productivity is a principle key to profitability. If you are competing with other mines that are paying roughly the same wage rate and the same prices for capital, materials, and energy, the only way your profit can be greater is by producing more output per unit of input. Mines with higher productivity have higher profit margins. Higher profit margins lead to greater operating cash flow, and cash flow is what distinguishes a dog from a cash cow. The turnaround in U.S. metals during the 1980s was in large part due to incredible improvements in productivity. According to statistics compiled by Kaufmann, 1991, labor productivity, measured as tonnes of primary production/manhour, increased 64% in steel, 94% in copper, 75% in lead, 143% in zinc, 132% in molybdenum, and 75% in gold. These improvements were hard won. However, with most modernization programs now complete, measuring and monitoring productivity becomes even more important as producers strive to maintain the gains they have achieved.

Jan 1, 1993

The evaluation of Abandoned Mined Lands can involve the investigation of very large areas of land. Often, the locations of critical areas or impending problems are unknown, and are not easily identified from the surface. Microseismic monitoring has been demonstrated to be effective in identifying potential instabilities and active movement in mines from distances of several kilometers. By placing sensors in proximity to, or in contact with, a high acoustic conductance layer close to the mined zone, large areas can be monitored for potential problems with a minimum of sensors and drillholes. As part of a U.S. Bureau of Mines contract, a prototype system was developed to identify and locate potential instability problems over wide areas of land. Once a problem area has been located, the system can be used to analyze the type of the problem, its size, relative degree of instability, and potential for damage. Continued monitoring after application of remedial measures can effectively determine the efficacy of those measures.

Jan 1, 1993

By J. Bickson, C. DeGennaro, J. Homer, M. Girman

Powered haulage and haul truck-related fatal accidents are among the most frequent at surface mines. Industry organizations developed guidance on accident scenarios to address haul truck and mobile equipment collision-related accidents. However, there is a need to investigate accident data to prioritize these scenarios and identify factors relevant to developing validation methods for collision warning/avoidance technologies and determining their capabilities and limitations. Standards and effective validation methods are necessary for improving system efficacy within mining operations and promoting industry adoption. To address these needs, researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated available powered-haulage and machinery-related fatal accident reports documented by the Mine Safety and Health Administration (MSHA). Their objective was to gain a perspective for informing the development of test protocols and validation methods through determining the most prevalent accident scenarios and related factors. Our findings afford insight for addressing the most prevalent haul truck scenarios and relevant factors within U.S. surface mining environments.

Mar 2, 2022

This United States Bureau of Mines study is based on a review of U.S. mine fire accidents that occurred from 1970 through 1989. Information on these accidents was obtained through investigative reports written by Mine Safety and Health Administration personnel. For this study, 260 mine fire accident reports were examined. A previous Bureau research effort established that fires causing fatalities were more likely to occur in haulage entries than at any other underground location. This study has found that the most prolific source of haulage entry fires was the inadvertent grounding of trolley wires. The largest segment (15 out of 40 trolley wire fires) resulted from not maintaining adequate clearance between the trolley wire and the vehicle. Several novel fire prevention and control ideas have evolved in response to frequently occurring fire-related problems. These included; discriminating power isolation devices, wire cutting devices, more accessible fire extinguishers, vehicle overcurrent protection, and vehicle fire suppression.

Jan 1, 1994

By J. W. Cash

The mineralogy and textures of cyclone dust, sludge, and occasional build-ups in the American Iron and Steel Institute (AISI) direct iron making pilot plant at Universal, Pennsylvania have been studied by reflected light, transmitted light, and cathodoluminescence microscopy, and phase compositions have been determined by SEM-EDS. The cyclone dust consists of particles of carbon, metallic iron, sulfur-bearing iron, and wustite. Measurements of particles in the sludge indicate that 69% are less than 2.5 µm across, 21 % are 2.5-5 µm, and 10% are larger than 5 µm. Mineralogically the sludge particles are mainly carbon and metallic iron, with minor wustite and sulfur-bearing iron. Build-ups that sporadically develop in the furnace consist of olivine, hercynite spinel, metallic iron, wustite, pyrrhotite, pseudobrookite, akermanite-ferroakermanite and gehlenite. The microtextures shown by the build-ups indicate that much of that material has precipitated at the build-up loci. This study has been supported by AISI and the U.S. Department of Energy.

Jan 1, 1995

By S. A. Moffatt

For several years iron ore processing plants, located in the northern U.S. experienced seasonal decreases in the grinding efficiency of their primary autogenous mills. Kawatra and Eisele (1992) studied this phenomenon in an operating plant and characterized it in terms of specific energy consumption (Fig. 1) and production of critical size material (Fig. 2). Critical size material is defined as ore that is too small to be effective grinding media and too large to be ground. This data showed that both specific energy consumption and critical size production increased during the winter months. The increased energy consumption was in part a result of an increase in the viscosity of the mill pulp at colder pulp temperatures. However, viscosity could not fully explain the changes in critical size production. These changes are most likely due to changes in the breakage characteristics of the ore. Other studies were also conducted to determine if thermal and physical properties of iron ore changed at colder temperatures. These are summarized below:

Jan 1, 1993

By D. R. Spears

The U.S. Bureau of Mines has had an ongoing interest in developing new reagent schemes for floating Stillwater, MT, chromite ore. Previous reagent schemes have been unsuccessful in achieving complete separation, primarily because little is known about the surface chemistry of the minerals in this ore. In order to design a rational reagent scheme, a study of the binding of various functional groups (R = -H, -OH, -CO2H, -NH2) on the two components (chromite and forsterite) of the Stillwater chromite was undertaken. Electron Paramagnetic Resonance (EPR) Spectroscopy was used to determine the adsorption isotherm, from a cyclohexane solution, of spin-probes which contained the functional group of interest. This was complemented by studies of the saturation surface coverage of the spin probe on the two minerals. In each case, more sites existed on chromite than forsterite; however, the forsterite sites were more strongly binding for each functional group. The results are discussed in terms of their implications for flotation.

Jan 1, 1994

By Robert J. Neubauer

I was asked here today to discuss the first long-term freight rate contract ever signed by a U.S. railroad and shipper. That was ICG's contract with the hoosier energy company to haul coal from southern Illinois to an Indiana power plant. I?ll also talk about why you can expect to see more such contracts in the future But first, let me tell you a little bit about the Illinois central gulf railroad and why coal contracts are so important to us. ICG is a principal mid-American freight carrier. We are one of the ten largest railroads in the united states and one of the ten largest coal-hauling railroads. ICG links the industrial great lakes region with the warm weather ports of the gulf coast. Some of the major points on our route map are Chicago; Indianapolis; Omaha; Kansas City; Memphis; St. Louis; and, of course, baton rouge and new Orleans.

Jan 1, 1981

By Daniel Connor, O&apos

The Cal-Sag Relief Sewer is a 2.6 m (8 ft 6 in.) diameter 9.1 km (5.7 mile) rock tunnel bored in dolomite for the Metropolitan Sanitary District of Greater Chicago. Included in the project are 18 shafts varying in depth free 70 m (230 ft) to 41 m (135 ft). This paper discusses how Healy/Vanessa reduced costs by eliminating conventional hand excavation by hoisting muck from a high production Robbins TBM (Tunnel Boring Machine) through small diameter drilled shafts and using a trailing rail-utility backup system.

Jan 1, 1985

By F. G. Miller

In mid-1972 we determined that a fresh approach to coal mining research was needed for the industry as well as for Bethlehem. The reasons to us were obvious: Productivity was in the throes of a steady decline, and labor and maintenance costs were spiraling upward. Yet, despite this predicament, nowhere in the U.S. at that time was there a comprehensive and coordinated research and development plan in the offing. The Bureau of Mines had not yet been charged with such a responsibility, and industry was content to rely on machinery manufacturers for innovations. After studying our own mining practices, the state-of-the-art of mining research elsewhere, and development work by manufacturers, we presented a comprehensive research package to our management at the end of 1972. The ideas and experience of many operating and management personnel in our Corporation contributed to the formulation of the final plan as approved.

Jan 1, 1976

By Gordon R. Haworth

During the past ten years we have experienced a period of rapidly-changing ground rules for the mining industry. Domestically we have had to contend with numerous new regulations controlling the impact of mining-related activities on the environment. However, for the purposes of this presentation we will assume that in the United States, after a certain amount of compromise on all sides, the industry will be able to work within the framework of the new regulations, and therefore we will concentrate on offshore developments. Due to the limitations in time and scope, this paper will be directed primarily toward the metal mining industry. We contend that the U.S.-headquartered mining company should remain active, and even expand its interests in foreign countries in the future. This is our feeling in spite of recent setbacks and the low return on investment experienced in recent years by some of the metal mining companies in their foreign operations.

Jan 1, 1975

By J. L. Ellenberger

The U.S. Bureau of Mines has cooperated with Cyprus Casa Grande Corporation Cyprus Casa Grande Mine, Cas a Grande, Arizona, since 1988 to assess the hydrology of an in situ leaching test facility. This work has resulted in an in situ design for leaching copper oxide ore that takes advantage of the increased mineral access associated with poor quality rock surrounding mine drifts. Blasting and bulkheads are used to produce readily-leachable rubble and contain and control solution movement, respectively. The design reduces the need for handling solution under high pressures in an injection/recovery system for in situ leaching of underground ore bodies. Early work at the site recognized a stress redistribution zone and increased transmissivity near drifts. Fracture data from a corehole oriented parallel to the dip of the ore body indicated an increase in fracture frequency around drifts a distance of 21 m (70 ft) away from the 5 m (16 ft) diameter drifts.

Jan 1, 1994

By JOHN R. HEBERGER, MAHIYAR F. NASARWANJI, Jonisha P. Pollard, Lydia M. Kocher

nt in the mining industry, and identifying factors associated with these injuries is critical for developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011 to 2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53 percent) followed by bone fractures/chips (26 percent). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals — such as pipe, wire and guarding — and hand tools as the primary sources of hand and finger injury. Although the information on glove use was limited, leather gloves were most often worn when an injury occurred.

By D. M. Stephens

Feeder-Breakers were an unknown but much needed piece of machinery when U. S. underground coal mines started converting to more efficient belt haulage of the R.O.M. coal as compared to conventional methods that the 1950's offered. These simple electromechanical machines offered efficiencies in three areas: (1) they contained a surge hopper that allowed a "load' of coal to be dumped without delay; (2) this material was fed horizontally by a drag chain conveyor into a rotating carbide pick breaker that broke all oversize material into a beltable size, and (3) it fed this broken material onto the belt conveyor at a rate conducive to its design. Since its introduction, the Feeder-Breaker has evolved from that first low capacity, low breaking force machine to today's model capable of breaking materials up to 5 MOHS in hardness and having throughput capabilities exceeding 3,000 TPH with availability in the 90 percentiles.

Jan 1, 1985

By K. E. Laughery

The Nevada Barite industry has experienced a 277% growth over the last five years with a total production of 2,542,000 tons. Total production prior to 1970 approximates 2,700,000 tons dating back to 1907 Annual production, as can be seen in Table 1, has increased from 192,000 tons in 1971 to 723,000 tons in 1975. During this same period U.S production has increased from 825,000 tons to 1,056,000 tons. Nevada is now the leading producer with 69% of the market. The increase in the Nevada barite production is, of course, directly related to the increased demand for weight material coupled with the lack of other sources and the relative economic advantage of the Nevada barite, A significant tonnage of Nevada barite is utilized in the non-oil well market, principally at FMC's barite chemical plant at Modesto, California; however the growth has been in the oil well market.

Jan 1, 1976