Search Documents

By Steven R. Lowe

Construction of a pump station, consisting of an inlet chamber, wet well and pump chamber, required excavation to a depth of 9.7 m (32 ft) below ground surface and more than 7.6 m (25 ft) below the ground water table in a rural, but rapidly developing part of southern New Jersey. Private houses are located [ ] within a few hundred feet of the pump station that use shallow wells for water supply. The pump station design anticipated support of the entire pump station on shallow foundations bearing directly on the underlying natural soils. However, during construction, uncontrolled ground water flow caused ground loss and damage to the bearing qualities of foundation soils. As a result, remedial repairs were required including support of the pump station on drilled pile foundations and releveling of the pump chamber that had settled. This case study is an example of where a poor understanding of the significance of upward flowing ground water had a major impact on the cost of construction. Anticipated subsurface conditions The pump station layout is shown in Fig. 1 with the locations of two borings made prior to construction superimposed. One of the borings was located within the footprint of the deep wet well excavation. Generally, this is not advisable where a deep excavation is required below the ground water table. This is because there is a history of projects where ground water seepage, or pressure, has broken out into an excavation through an ungrouted borehole and compromised the integrity of foundation soils. Logs of the borings did not indicate that the borings [ ] were grouted upon completion.

Jan 1, 2011

By Nathaniel Arbiter

Flotation’s earliest patent was issued in 1860. However, the process was first applied commercially in Australia until 1904, and in Montana in 1911. Major advances followed both in reagent treatment and in cell design, with resulting process improvements. Mechanical cells have seen the widest use and with the major increases in plant capacities (Fig. 1) their volumes have also increased (Fig. 2). In 1991, the principal use for the process was to produce copper concentrates for smelting. It was applied to 243 Mt (268 million st) of copper ore. The total of all ores floated that year was 426 Mt (470million st). In 1997, US mines produced 257 Mt (284 million st) of copper ores for flotation, yielding1.75 Mt (1.94 million st) of copper.

Jan 1, 2000

By S. Roy

Soft laminated iron ore (SLO) having a higher hematite content and Martite goethite iron ore (MGO) having a higher goethite content were subjected to detailed characterization and beneficiation. The present research was designed to investigate if these abundant, low-grade ores can be enriched adequately using standard industry techniques. No significant enrichment of the ores using jigging operation on the coarse (-3,200 +595 mm) size fraction could be achieved. Good liberation was only attained in the 150 to 300 mm particle size range in both cases. Desliming enriches the ground ores significantly. The effect of the feed size on the separation efficiencies of the ground ores were studied using flowing-film concentration on a Wilfley table. Better enrichment is obtained in the case of 150-mm sized feed by tabling. The grade of SLO is improved from 56.14% to 66.51% Fe, while the Fe content of MGO is enriched from 55.16% to 65.83%. Substantial rejection of alumina and silica is also achieved. Due to the friable nature of MGO and the higher goethite content in it, the loss of Fe in the form of ultrafines is greater in this case compared to that of SLO.

Jan 1, 2009

By J. D. Lowell, L. Quevedo

I will talk today about a porphyry copper exploration program now underway in the Amazon jungle in the southeastern part of Ecuador near the border with Peru. The project is unusual for two reasons: first the deposits are of Jurassic age, 153 m.y.o., which is unusually old for porphyry copper deposits and they may be the most significant pre-Tertiary age porphyry deposits known. Second, the district was found only six years ago which makes this the most recent discovery of a totally new porphyry copper district. The new porphyry district, known as the Zamora River Copper Belt, or the Corriente Copper Belt, is a north trending area 50 km long by 10-15 km wide, which is nearly aligned with the axis of the Jurassic age Zamora batholith and with the course of the Zamora river. Gencor in 1994 initiated a regional grassroots gold exploration program based on reconnaissance geologic mapping and geochem sampling which did not find a gold mine, but which identified the San Carlos porphyry copper system in April, 1995. In a later reorganization between Gencore and Billiton the Ecuador project was transferred to Billiton and between the Gencore work and Billiton’s a total of 10 porphyry copper systems were found over the next four years. In the period of 1997 - 1999 Billiton drilled a total of 11,000 meters of wide spaced core holes in the San Carlos, Panantza and Kutukus prospects. In October 1999 Billiton concluded a farm-out, joint venture agreement with Corriente Resources and Lowell Mineral Exploration for additional exploration of the Zamora property. This is funded by Corriente and managed by Lowell Mineral Exploration and a total of 28,000 m of core drilling was completed through August 2001. An immediate result of the Corriente Lowell project was the discovery of potentially commercial ore reserves in two new deposits at Mirador and Warintza. Additional closer spaced drilling was done in the Panantza deposit and additional drilling is planned at San Carlos, in targets related to Warintza, and elsewhere.

Jan 1, 2002

By Raymond W. Henn, Kent A. Pease, Glen J. Rorison

The paper focuses on construction of a 2.55-km (8,365-ft) long, 2.4-m (8-ft)diameter storm drain tunnel in Evansville, Indiana. The tunnel was driven through saturated soft ground varying from clay to fine sand. The paper presents: an overview of design and design rational including specific EPB machine requirements; the contractor’s proposed and accepted alternative construction methods and TBM design; and construction issues and performance. Some of the key points discussed are the use of the TBM in different operational modes for alternative ground conditions, the effectiveness of dewatering systems, production rates, and issues such as surface settlements and gas.

Jan 1, 2001

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4-km- (6.5- mile-) long, 14.4-m (47.5-ft) bored tunnel that will run under the city of Niagara Falls from the Upper Niagara River to the Sir Adam Beck power station. The completed project will enhance the capacity of the Sir Adam Beck power station by adding 500 m3 /sec (17,657 cu ft/sec) of water through the tunnel. The project uses the world?s largest hard-rock tunnel boring machine (TBM) at 14.4 m (47.5 ft) in diameter to excavate the tunnel. Features of the project include the use of a high performance (HP) main beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area In June 2004, the Ontario government announced that Ontario Power Generation (OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls ? the first two tunnels were constructed in the 1950s using drill-and-blast techniques. The third tunnel, appropriately named the Niagara Tunnel Project (NTP), consists of a 10.4-km- (6.5-mile-) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG the selected of Strabag of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP at a price of C$600 million. In September 2005, Strabag selected The Robbins Co. of Solon, OH to design, manufacture and deliver a new 14.4- m- (47.5-ft-) diameter high performance, state-of-the-art main beam hard rock TBM to be used in the excavation of the tunnel. To meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be sup-plied as ready-to-bore within a 12-month period after the contract was awarded to Robbins.

Jan 1, 2008

From a vast army of workers to gargantuan machines to immense volumes of material being moved, almost everything about the Port of Miami Tunnel (POMT) project points to tunneling on a massive scale. Almost.The star of this underground and underwater show is a Herrenknecht tunnel boring machine (TBM,) nicknamed ?Harriet? by a local Girl Scout troop. With her 12.9-m- (42.3-ft-) diameter cutting head and a total length of 139 m (457 ft), Harriet is boring through thousands of cubic meters of clay, dirt and sand, which is often mixed with coral and other materials, to create two 1,280-m (4,200-ft) traf?c tunnels connecting Watson Island and the Port of Miami (Dodge Island) beneath Biscayne Bay, FL. But in the midst of all of the oversized equipment and machines, a strong contender for the best supporting nod goes to a relatively tiny machine: the Brokk 400. Bouygues Civil Works Florida crews are using the compact, remote-controlled and electric-powered machine to excavate five cross passages between the twin traffic tunnels. The pas-sages will be essential to the safety of people who drive their vehicles under the bay every day.

Sep 1, 2013

New Mexico?s active coal mines have reclamation challenges that are being successfully resolved through the application of geomorphic grading methods. Soils and overburden material are often of poor quality, and annual precipitation is low. Revegetation on south and west aspect slopes often failed to persist. The New Mexico Mining and Minerals Division had therefore been encouraging topographic diversity on reclamation to improve water harvesting and reduce the percentage of south aspect slopes. Steeply dipping, multiple coal seams may be mined by open pit methods. Structurally-controlled trellis drainage patterns that exist premine have to be replaced with dendritic drainage patterns on reclamation where the overburden had been pulverized. Sodic spoil material is prone to differential settling and the creation of piping features in areas where runoff ponds, which may lead to downslope instability. In each of these scenarios, the approximation of natural drainage patterns on the reclamation has reduced erosion and sedimentation by creating shorter slopes with correct profiles, and by improving conditions for revegetation establishment.

Jan 1, 2010

By F. Calizaya

The PT Freeport Indonesia‘s Deep Ore Zone(DOZ) copper deposit is located in the province of Irian-Jaya, Indonesia. Currently, a block cave mine is being developed around this deposit. Production is scheduled to start in year 2000 and to ramp up to25,000 tpd by year 2003. The air quantity requirement for this mine is equal to 780 m3/s. To supply this quantity, the mine will require five centrifugal fans (one 450 and four 750 kW fans). This study summarizes the technical aspects related to the installation and commissioning of one of these fans. The fan was installed on the surface in a parallel arrangement with two others. It has a design capacity of 240 m3/s of air at 2.2 kPa of static pressure. The study presents the installation details from the underground shaft excavation and portal development through fan testing and commissioning. It also presents the results of a monitoring system that was installed to determine the fan duties.

Jan 1, 2000

By Michael Harris, David Mosch

The numerous small high grade gold and silver deposits of the Front Range Mineral Belt have been uneconomical because of the high costs of mill construction, transportation, and smeltering. Processing of these ores must be simple, cheap, with satisfactory recoveries, and be environmentally acceptable. Vat leach with direct electrolytic recovery satisfies these parameters. A battery of testing was conducted utilizing bottle and bucket tests. A five ton vat leach with direct electrolytic recovery gave excellent results while a five ton heap leach proved impractical due to channeling.

Jan 1, 1987

By Jaidev Sankar

The dream of constructing the new Second Avenue Subway in New York has finally become reality as the first construction contract package is currently underway. This first contract requires the construction a TBM Launch Box in the middle of Second Avenue from which a Tunnel Boring Machine (TBM) will bore two tunnels south to 63rd Street. This paper will discuss the design of this contract and how construction has progressed including preparation, site constraints, utility construction and com-munity impacts while highlighting the challenges of working in an urban environment. It will also discuss moving forward on this major project outlining the remaining contract packages including their scope and status.

By Michael J. Rinker, P. A. Tibble, M. Wiseman, R. V. Nicholson

Tailings, from an active copper-zinc operation, containing about 10% sulphur were investigated to assess the onset of acid production and potential lime requirements for treatment of drainage. Oxygen consumption rates were measured over two years to verify spatial and seasonal variations in sulphide oxidation rates. Shallow cores were collected to assess the quality of tailings porewater and to characterize solids that had been subjected to oxidation and depletion of neutralization potential (NP) for several years. Oxygen consumption data were used to quantify rates of NP depletion and onset of acid drainage from the near- surface tailings. Based on measured oxygen consumption rates and identification of NP remaining in the tailings, future lime use in the treatment plant was expected to rise significantly without mitigation. Geochemical modeling calculations were calibrated with observed oxygen consumption rates and the model results agreed well with actual lime use in the waste water treatment plant during operations. The modeling also demonstrated the benefits of lower lime demands and treatment costs after closure as a result of construction a soil cover on the acid generating tailings.

Jan 1, 2000

By Jochen Belz, Allan Henneker, Nod Clarke-Hackston

For the construction of tunnels and other underground structures, extraction of the exact amount of material is of paramount importance both economically and for engineering purposes. In the Sequential Support Method (NATM) immediate (sequential)and smooth support by means of shotcrete, steel arches, lattice girders and rockbolts, either singly or in combination are used; cutting of the precise (albeit sometimes of complex geometry) profile is an integral part of the method. In order to save unnecessary excavation and provide better information to the machine operator, VMT GmbH has developed a system to support precise excavation of the tunnel profile when using road headers or other partial face cutting machines. This paper outlines the principles of this system with examples from Australia, Ger-many, Sweden and Spain and will cite examples of typical savings achieved.

Jan 1, 2007

By Steve Kral

Good times make for happy miners. And the past few years have seen a lot of smiling mining engineers, geologists, metallurgists, corporate executives, analysts, investment bankers and shareholders. And nowhere was that more evident than at the 74th Prospectors and Developers Association of Canada’s (PDAC) annual meeting. The meeting, held in Toronto March 5-8, attracted a record 14,500 people. Of those, the PDAC said attendees came from an estimated 100 countries. And about 40 countries sent national delegations to the meeting. Argentina, for example, sent nearly 100 people. The PDAC meeting has always been a event where companies and individuals can get a look at numerous properties in all parts of the world that could potentially become major mines. And through the many receptions, hospitality suites and just sitting in the local restaurants and taverns, deals are usually made.

Jan 1, 2006

By Harry Asche

The last 12 months has seen the construction of the first Earth Pressure Balance (EPB) TBM excavated tunnel in New Zealand on the Project Hobson sewer storage tunnel for Watercare Services Limited, with the concurrent excavation of the second EPB tunnel on the Rosedale Outfall project for North Shore City Council. Together these tunnels involve a total length of 6km and follow an 8 year pause in TBM activity in Auckland. TBM performance on these two projects is thus of significant interest as there are four major tunneling projects totaling over NZ$8B being planned for Auckland, in similar ground conditions. Auckland?s bedrock is a weak sandstone/siltstone (East Coast Bays Formation), subject to infilled paleovalleys. The geology in the region has been significantly influenced by volcanic activity; 49 volcanoes are present within 20km of the city centre. The paper describes the design and construction challenges for the projects, including TBM performance, ?sticky spoil? management, and risks associated with basalt lava flows and two paleovalleys. Watercare?s Project Hobson also saw the successful implementation of a Geotechnical Baseline Report?one of the first uses of this type of document in Australasia. Rosedale Outfall is designed for high internal water pressures with varying hydraulic flows, with the risk of exfiltration explicitly addressed.

By M. Gangal

CANMET-MMSL, in cooperation with Dry Systems Technologies and Quinsam Mine, conducted a study to determine the effects of B50 biodiesel on the emissions of a flameproof diesel power package in comparison with mining diesel fuel for application in underground coal mines. The emissions testing for coal mine application requires that the intake air mixture to the engine should be at 1.25 percent methane by volume in air. The tested power package system included a naturally aspirated, mechanically-controlled diesel engine with a diesel oxidation catalyst (DOC), a heat exchanger, flame arresters, and a low temperature disposable diesel particulate filter. The engine dynamometer tests were conducted at the CANMET-MMSL Diesel Emissions Research Laboratory in Ottawa using the ISO 8178-C1 test protocol. The separate and combined effects of a B50 biodiesel blended fuel, and with and without 1.25% methane enriched intake air were measured on a diesel power package. Fuelling the baseline engine (without methane), with B50 biodiesel blend reduced carbon monoxide (CO) by 44%, and increased nitrogen dioxide (NO2) by 19%, and particulate matter by 31% relative to the mining diesel fuel. Similarly, injection of 1.25% methane to the intake air for baseline engine with mining diesel fuel increased engine power by 15%, CO by 124%, and NO by 15%, and decreased NO2 by 13%. The effect of B50 biodiesel relative to the mining diesel for coal mines application (with methane for both fuels) was to reduce CO by 27%, and NO by 6%, and increase NO2 by 23%, with no change in engine power. The overall results indicate that the minimum ventilation rate for the equipment application in coal mines with B50 biodiesel was 4.11 m3/s (8,700 cfm), slightly higher than the ventilation rate of 4.01 m3/s (8,500 cfm) with the mining diesel fuel. This slight increase in ventilation rate for B50 biodiesel fuel was due to an increase in NO2 at one of the operating test points, and the ventilation rate for this equipment was governed by NO2 in the exhaust gas.

Jan 1, 2009

Several economic factors have caused the surface mining industry to require large-capacity shovels and trucks for efficient, high-production, low-cost operations. Some of those factors include technological advancements in equipment, commodity market depressions, increased labor and maintenance costs, contractural obligations and harsh operating conditions. The difficult operating conditions in surface mines, however, pose challenges to the use of high-capacity equipment. They include space limitations, weak over-burden, and weathered soils and rocks. So mining companies face major challenges in selecting appropriate shovels to meet the technical, operating, safety, environmental and economic requirements of their mines.

Jan 1, 2003

By Peter N. Calder, J. L. Workman

There are many opportunities for computers to assist in dragline mine planning. Three important areas particularly lend themselves to computer assisted study. These are overall mine design and planning, the computation and display of range diagrams and the calculation of production and production variability. The computation of range diagrams is of particular interest because of the importance of matching the dragline and site geometries. This paper examines the uses of range diagrams in dragline mining and illustrates the application of computer techniques to the computation using one such program as an example. The use of computer generated range diagrams for machine selection, pit design and in parameter analysis is discussed. Directions for further development are also provided. There is a great deal that can be done to additionally enhance the ability to provide accurate designs for the dragline operation. One area that needs special attention is the dumping of overburden around access ramps into the pit. This situation is one of the most difficult dumping sequences and affects machine selection and pit operation. It is also suggested that programs that simulate the production schedule of the drag-line would be useful. It is concluded that large overall mine planning programs are very important in dragline mining. However, smaller programs designed for a specific, task are also important tools in many cases. These are easy to learn and use, well adapted to the PC environment and provide useful information, both for design and for daily planning.

Jan 1, 1989

By J. S. Stachulak

The Diesel Emissions Evaluation Program (DEEP), a research consortium formed in 1997 by Canadian mining companies, labour unions, and provincial and federal government departments, completed its work by mid-2006. This program, in which Vale Inco participated with both direct funding and in-kind contributions, investigated the ability of currently available technology to significantly reduce underground concentrations of diesel particulate matter (DPM) with high efficiency and low maintenance over a long-term period (years of life).While DEEP?s testing showed that engine maintenance is a critical component for lowering DPM, it was clear that reduction of DPM to the very low target levels of ~0.05 mg/m3 was not possible with maintenance alone. The best candidate technology for achieving low DPM levels was particulate filter systems. Furthermore, successful deployment of such systems was highly dependent on removing them from having to rely on human intervention for their regeneration. The search continues within Vale Inco to identify a reliable and rugged system.

Jan 1, 2009

By E. Sun

Tailings disposal is a significant consideration for the mining industry, with the majority of the ore processed in most mining operations ending up as tailings. Several tailings dam failure accidents have occurred during the past few years and mine tailings dam failures are occurring at relatively high rates. Tailings dam failure is disastrous with the serious damage and the loss of lives. To increase the tailings dam safety, a tailings dam monitoring and pre-alarm system (TDMPAS) based on the internet of things and cloud computing platform has been accomplished with the abilities of real-time monitoring of the saturated line, impounded water level, rain fall and the dam deformations etc. The TDMPAS has been applied in several mines in China and helped the mine engineers monitor the tailings dam safety and get warning information automatically and remotely in any kind of weather conditions. This work has been demonstrated the tailings dam monitoring and pre-alarm system (TDMPAS) is meaningful to monitor the tailings dam physical safety condition. The TDMPAS could be applied to monitor all the national tailings dams online in the future.

Jan 1, 2012