Search Documents

Council for 1996/97 President Dr N.A. Barcza President Elect R.P. Mohring Vice Presidents Senior J.R. Dixon Junior M.H. Rogers Immediate Past President D.A.J. Ross-Watt Honorary Treasurer J.A. Cruise

Jan 1, 1997

By H. Jalkanen, L. Holappa

The main role of slag in oxygen converter processes is to absorb the non-volatile oxidation products of hot metal impurities, Si, P, Mn, Ti, V, etc. The importance of converter slag as deP and de Smedia has ceased with implementation of special pre- and post-converter treatments. The transfer from top blowing (LD) to combined blowing converters has decreased the amount of slagged iron that, together with the tendency towards lower silicon and manganese contents, has decreased slag to steel ratio. Still the control of slag forming and behaviour during the blow is of great importance. In this paper the thermodynamics of the slag forming reactions, the role of slag in the modern oxygen converter process for impurity elimination, splashing, lining wear, dust formation and post combustion are discussed on the basis of common knowledge and experience of Finnish steel plants.

Jan 1, 2004

By R. Banda

This paper describes the decision to implement and then the implementation itself, through trials, of electronic ?Smartdets? over previously used shock tubes. It concludes that Mufulira Mine has become the first mine in Zambia to convert 100% of its stoping to ?Smartdets?, because the Mine?s management was prepared to look beyond the unit cost of product and were ready to look at the broader picture of cost effectiveness and increased productivity.

Jan 1, 2005

By O. Gunaydin

Performance measurements of large-diameter circular saws were conducted on eight different carbonate rocks in marble factories located in some areas of Turkey. Rock samples were collected from these factories for laboratory tests. Uniaxial compressive strength, tensile strength and impact strength were determined in the laboratory. The brittleness of B3 (the ratio of compressive strength minus tensile strength to compressive strength plus tensile strength), the brittleness of B5 (the product of percentage fines in the impact strength test and compressive strength) and the brittleness of B8 (half of the product of compressive strength and tensile strength) were calculated from the test results. Hourly slab productions were correlated with brittleness indexes. It was concluded that sawability of carbonate rocks can best be predicted from the brittleness of B8.

Jan 1, 2004

By C. Nexhip, S. Sun

Critical to understanding and controlling phase mixing and separation in metallurgical processes, is the development of reliable experimental techniques to measure interfacial properties of melt systems. A series of experiments has been carried out to determine the effect of oxygen potential on the surface tension of liquid copper. Using an electromagnetic levitation method, a surface tension-oxygen chemical potential adsorption isotherm was produced for the Cu-O system at T 1400 K. The surface tension results show good agreement with the literature values e.g. within 3 per cent for pure copper. The Belton `ideal' adsorption isotherm was applied, and the following equation derived to best fit the experimental data ? =1251-77.5 1n41+ (2.79x105 . pO1/2)](mN.m Using this equation, the surface tension of copper was calculated/predicted as a function of oxygen potential at 1400 K, and showed excellent agreement with the experimental values. This confirmed that the adsorption behaviour of oxygen in liquid copper is ideal. The saturation coverage of oxygen on the surface of liquid copper was determined to be T0 = 6.65 µmoles.m,-2 corresponding to an area per adsorbed oxygen atom of ao ? 25 Å2. These values agree well with those cited in the literature, and our experimental data cover a very wide range of oxygen potential (10-5 to 10-17 atm). Keywords: levitation melting, surface tension, Cu-O alloys, oxygen potential, adsorption isotherm, surface coverage.

Jan 1, 2004

By M. A. van Nierop

The Discrete Element Method (DEM) is a model that is used to simulate the motion of the media in a grinding mill. The sum of the energy that is lost in inter-media and media-wall collisions represents the power drawn by the mill. The fact that the DEM predicts the power drawn by grinding mills over a large range of diameters has been used to show the validity of the DEM. However, the power drawn by a mill is a function only of the sum of forces of the load on the shell liners. A more accurate and detailed validation of the DEM would be to measure these forces as a function of angular position as the liner moves under the load, and to compare these measurements with predictions generated using the DEM. An experimental mill has been developed to reproduce exactly what the 2-dimensional DEM simulates. The 0,55 m diameter mill has a length of 0,023 m, which is fractionally larger than the diameter of the media used in the mill. One of the lifters in the mill has been instrumented so that the forces on the lifter can be measured as the mill rotates. The DEM simulation will be used to predict these forces. This will give experimental evidence of the validity of the DEM for modelling load behaviour in rotating grinding mills.

Jan 1, 1999

By B. Elevli

The aim of this paper is to demonstrate the implementation of multicriteria analysis in selection of the most suitable underground ore transport system for a chromite mine in Turkey. The related problem includes five possible ore transport systems and six criteria to evaluate them. The adopted evaluation and ranking method for this study is PROMETHEE. PROMETHEE I revealed a partial order of alternatives where incomparability exists. PROMETHEE II gave the absolute ordering of alternatives. The results have shown that the PROMETHEE method can be successfully used in solving mining engineering problems. Keywords: multi-objective, decision analysis, mining, ore transport system

Jan 1, 2004

By D. C. Andersen, G. L. Smith, J. Pearson-Taylor

Following a restructuring of Anglo Platinum Limited in 2004 the strategic long-term planning function has been centralized. This paper describes the revised strategic long-term planning process covering aspects of the planning cycle, systems and methodologies, categorization of capital expenditure, corporate governance and planning tools.

Jan 1, 2006

By F. T. Cawood

Monitoring of the slopes of surface mines can prevent loss of life, loss of equipment, loss of production and possibly the loss of the mine. The effectiveness of such monitoring depends on the extent to which slopes give adequate advanced warning before failing, and on the ability of the monitoring system to detect such warning. In this paper an overview is given of slope monitoring requirements, from both the geotechnical and survey points of view, as well as the types of equipment and instrumentation that are available. Legal issues relevant to slope monitoring are also dealt with. It is concluded that conventional geotechnical and survey instrumentation will continue to have their place in slope monitoring. However, the slope monitoring scene has changed substantially in recent years. A real and volume-based monitoring equipment is now available and this has provided, and will continue to provide, the means to improve safety, and to enhance productivity in mining. Its benefit to slope management is substantial. In the near future it is expected that data obtained from such equipment will add a much needed new dimension to slope engineering, and be used to improve slope designs and to optimize slope angles.

Jan 1, 2006

By D. H. Diering

The paper deals with the technologies required for opening up anew idealized ultra-deep level mine. First the overall philosophy of accessing ore at ultra depths is discussed. Then the individual technologies which will be required are explored. Finally a detailed overview on one of the key technologies, namely tunnel support, is given. Because this project is still in its infancy, few definitive answers are provided; instead each of the envisaged technologies are briefly discussed, with emphasis on those which require the element of speed for rapidly accessing the ore body.

Jan 1, 1997

By N. F. Mescheriakov

New mechanical and pneumatic-mechanical flotation machines with axial impellers have been developed. Industrial tests show that these machines ensure lower power expenditure (on flotation) by 1.5-2.0 times as compared with reference machines (with the same or improved technological indices). Application of the newly developed axial impeller, with these advantages, is possible in any volume chambers of type OK, Dorr-Oliver, Wemko etc.

Jan 1, 1998

By P. T. Slatter

The efficient and accurate design of pipe and pumping plant for non-Newtonian mineral slurries remains a problem. The objective of this paper is to present the development of the Balanced Beam Tube Viscometer (BBTV), an instrument which could facilitate more accurate design for these slurries. The background of rotational and tube viscometry is reviewed and the fundamental principles and inherent advantages of the BBTV are given. The design, data acquisition and processing techniques are introduced and results showing the reliability of the new instrument are presented and discussed. It is concluded that the BBTV is a reliable and versatile instrument for both routine analyses and research work, and has the potential to provide data for the refinement of the design procedure for mineral slurry pipe and plant design.

Jan 1, 1998

By T. E. Pogue

This paper traces the co-operative initiative undertaken by South Africa?s gold mining companies through the Chamber of Mines Research Organization (COMRO) in development of hydraulic technologies. After a brief description of the structure of these technologies? development under COMRO?s stewardship, the paper turns to an overview of the structure of innovation within which these hydraulic technologies were developed. A central focus of this paper is systematic review on whether similar technologies are likely to emerge in the present system of innovation and the role played by innovation policy.

Jan 1, 2006

By F. T. Cawood

The new South African Mineral Policy has major implications on the way mineral rent will be collected and shared between the stakeholders in future. Although the policy does not supply details on how this will be done, drastic departures from practices under the previous dispensation require a new approach. For example, there introduction of the ?right to mine? principle implies that the repealed lease consideration concept will be expanded to all minerals. The new policy also makes provision for predetermined standard terms and conditions for all prospecting and mining permissions. It also states that, regardless of whether the mineral rights are state or privately-owned, all prospecting fees and mineral royalties will be determined by state officials after consultation with the registered holder of the mineral rights. This paper proposes a standard mineral royalty formula that complies with the principles mentioned in the White Paper and has been shown to be internationally competitive.

Jan 1, 2001

By R. J. Jewell

The storage capacity of any given tailings storage facility (TSF) is a function of the volume available for the tailings, for which the geometry of the final upper surface of the tailings is most important. One of the advantages that can be obtained from thickening tailings prior to discharge is that the tailings can be stacked at a steeper beach angle than is obtainable with conventional low-density slurries. However, there is at present no universally accepted method available for the accurate prediction of tailings beach slopes. This paper examines the current situation with the objective of putting the quest for a method for the accurate prediction of beach slopes into perspective. The paper references published reviews of the best-known beach slope prediction methods. However, there do not appear to be any independently verified projects or published references to projects on which a Class A prediction has been validated for any of these approaches, and in those instances where projects have been implemented correlation of actual with predicted slopes has been poor - often due to differences between the properties of the tailings assumed in the design and those actually achieved in the field. The author also concludes that flume-scale testing cannot be taken as a reliable indicator of full-scale performance, and suggests that the outcome of any current predictive method should be used by experienced practitioners as only one of a range of indicators in order to suggest a range of slope angles likely to result for any given operation. Practice has shown that it is possible to manipulate beach slopes by changes to the disposal technique, such as limiting the rate of discharge per discharge point and by increasing or decreasing yield stress, but the impact of these changes cannot readily be predicted. There are also newly emerging technologies, such as the injection of a polymer into the tailings at discharge, that will enhance the dewatering of tailings and hence expedite the consolidation of the tailings, that could well facilitate the development of steeper beach slopes. The overall conclusion is that with the current state of knowledge, the accurate prediction of beach slopes is not possible. Furthermore, in view of the inherent variability of the tailings parameters from any operation, it may well be of more value to concentrate on developing an understanding of the means by which the tailings parameters may be manipulated by the operators to achieve a given beach slope than to concentrate wholly on developing a generic beach slope prediction model.

Jan 1, 2012

By J. W. Neale

Mintek and BacTech have joined forces to provide the metallurgical industry with bacterial-oxidation processes for the treatment of sulphide ores. The processes are aimed at both refractory gold-bearing and base-metal concentrates. Previously, BacTech had commercially implemented the refractory gold process at the Youanmi Gold Mine in Western Australia. More recently, the process has been incorporated in the Sulphide Treatment Plant at the Beaconsfield Gold Mine in Tasmania, Australia. In addition, Mintek and BacTech have recently signed an agreement with the Laizhou Gold Metallurgy Plant in China?s Shandong Province, which will see the third commercial realization of the technology for refractory gold. Development of the base-metal technology is the subject of several papers in the proceedings of this colloquium. The implementation of the refractory gold technology at Beaconsfield is discussed in detail. Some important aspects that are covered include: ?Test work, and the choice of bacterial culture ?Process design choices, and the advantages of the Mintek-BacTech process ?Inoculum build-up ?Plant commissioning ?Plant performance. Besides the Laizhou project, Mintek and BacTech are currently investigating several other commercial prospects for the technology. These include the use of the technology for a gold-copper deposit, where the production of both gold and copper is envisaged.

Jan 1, 2000

By B. J. du Plessis

Automation of the conventional grinding circuits of Palabora Mining Company (PMC) required that adequate instrumentation and a control system had to be put in place, after which extensive testing had to be done to evaluate different grinding control strategies. The objective was either to optimize the particle size from the grinding circuit, or to increase milling circuit throughput while maintaining particle size at existing levels. Prior to automation of the process as described below the circuits were controlled manually. No on-line information on cyclone feed densities, cyclone feed flow or cyclone overflow particle size was available. This type of control relied heavily on interpretation of the process parameters by the operator and on his ability to make informed decisions on what the set points should be. An integral component of the automation process was the installation of a SCADA package (SysCad SDX) for implementing the on-line control strategy. A self-correcting model for prediction of cyclone particle size was developed and implemented on the SDX. The model is calibrated using values from the particle size analysers while they are operational. If the particle size analysers choke or fail for any reason, the model continues to provide a good estimate of the particle size. This technique ensures that a continuous particle size indication is available compared to the intermittent reading from the instrument. The continuous signal allows particle size to be used as a process variable for control purposes. A strategy was developed and implemented which allows for the production of a controlled grind size from the conventional milling circuit to the flotation circuit. The grinding control strategy allows for the control of particle size from the individual cyclone overflows. This strategy allows the operator of the process to increase or decrease production rate by specifying a coarser or finer grind size required for flotation.

Jan 1, 2001

By S. Kahraman

The correlations between the modulus ratio and penetration rate of rotary and percussive drills were statistically investigated using the raw data obtained from the experimental works of different researchers. An inverse power law was found between the modulus ratio and the penetration rate of rotary and diamond drills. The penetration rate of rotary drills and diamond drills decrease with an increasing modulus ratio. The penetration rates of percussive drills increase with an increasing modulus ratio. There are significant linear correlations between the penetration rates of percussive drills and the modulus ratio. In one of the cases of percussive drilling, a strong correlation between the penetration rate and the modulus ratio was found for the rocks having a porosity value lower 1.23 %. It can be concluded that the modulus ratio might be a representative measure of rock drilling efficiency. However, further study is necessary to check the validity of the derived equations for other rock types. The effect of porosity on the correlations between the modulus ratio and penetration rate needs to be further investigated.

Jan 1, 2003

By C. F. Vos

Small replacements of C12-trithiocarbonate (C12-TTC) for dithiocarbonate (DTC)/dithiophosphate (DTP) in a reagent suite for the flotation of platinum group metals (PGM) have significantly improved the rejection of gangue. Coupled to this is an improvement in kinetics, grade and recovery of PGMs. In a pilot-plant trial, after a 5 mole per cent replacement of the current DTC/DTP collector combination by C12-TTC, large opaque bubbles were replaced by small clear ones. In addition, a similar flotation response was realized with one-third of the current depressant dosage. During a preliminary plant trial on underground UG2 ore, the initial rougher concentrates were characterized by higher PGM concentrate grades and this was in part due to improved chromiter ejection. The concentrate produced from the TTC trial also exhibited a much finer particle size distribution. The overall circuit performance, which included secondary regrind and flotation, showed an increase in concentrate grade of approximately 44% while the tailings grade remained unchanged

Jan 1, 2007

Council for 2002/2003 President S.J. Ramokgopa President-elect T.R. Stacey Vice-presidents Senior F.M.G. Egerton Junior W.H. van Niekerk Immediate Past-president A.A.B. Douglas Honorary Treasurer J.A. Cruise

Jan 1, 2003