Search Documents

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By K. E. Robinson

This study provides an initial indication that mill tailings produced in the Coeur d'Alene Mining District of Idaho can be placed on floodplain areas in a technically acceptable manner without artificial liners and without seriously contaminating the surrounding area. Tests have shown that landfills on these unused areas can result in returning these areas to productive use. The engineering properties of mill tailings permit construction of stable embankments. Designed slope protection inhibits water erosion. Among the environmental considerations in using tailings for landfill construction are the acid and other contamination produced by tailings and wind erosion of exposed tailings surfaces. The initial results indicate that adverse impacts are not as severe as previously thought, and mitigative measures are feasible. Based on the preliminary data, and in accord with existing Federal and State waste management regulations, a conceptual design has been developed for 23 potential landfill sites in the District, which could reclaim 750 acres of floodplain. A cost analysis of landfill construction with mill tailings indicates that the method would be an economically viable means for increasing the valleywide tailings storage capacity, provided construction with slurried tailings is feasible. A Stage H study is proposed to evaluate slurried tailings as a foundation material, as opposed to hauled tailings used in this present study.

Jan 1, 1981

By David C. Oyler, Dennis R. Dolinar, Christopher Mark, Craig S. Compton

Fully-grouted roof bolts comprise more than 80% of the primary roof supports used in U.S. coal mines. However, nearly 1,500 MSHA reportable, non-injury roof falls occur each year, and most of these are attributable to failure of the roof bolt system. Anchorage failure is one failure mechanism for fully-grouted bolts. As roof deformation works its way upward, the bolts can become heavily loaded near their upper ends. If the applied load exceeds the anchorage, the bolts will simply pull out. Research dating back 30 yrs indicates that this type of anchorage failure is most likely when the roof rock is weak, just where roof support is most critical. In soft shale or coal roof, the small amount of data available in the literature indicates that 20-30 in of resin anchorage may be required to achieve the full capacity of the bolt. In other words, the “full resistance zone” of a 60 in bolt may actually be just 30-40 in. Despite its potential importance, there is no widely accepted anchorage test for fully grouted bolts. Standard pull tests have sometimes been employed, but they provide no information on the anchorage near the top of the bolt. An alternative, first described more than 25 yrs ago in the U.S., is the short-encapsulation pull test (SEPT). With this test, the bolt is installed with only a short (1 ft or less) tube of resin. In recent years variations of this test have become international standards. v

This Bureau of Hines report on underground mine communications addresses methods and equipment to meet the communication requirements of working sections and places of coal and metal-nonmetal mines. A review of the status of trapped miner detection is also presented.

Jan 1, 1977

Background: Frictional ignitions continue to be a problem facing the U.S. underground coal mining industry. Many methane igni-tions are associated with the impact of mining machine cutter bits on quartzitic material (e.g., sandstone) during the coal-cutting process. Most ignitions result in small methane-air fireballs often only a few feet in size and limited to the cutter head location. However, under certain conditions, frictional ignitions can lead to larger methane explosions and/or fires with the potential for causing serious injury or death to the mining machine operator and other nearby miners. The requirements for a frictional ignition are a flammable volume of methane-air and an ignition source. This source is usually the hot streak caused by the frictional impact of the mining bit on hard rock, and the frequency of occurrence increases with increased bit wear. Another possible ignition source is the fric-tional impact of rock on rock during a roof fall.

Mar 1, 2008

By E. Chin

Under the seventh 5-year plan (1986-90), the Chinese Government continued to implement reform and to open the country further to the outside world in order to accelerate the growth of its national economy. As a result of expanded foreign economic exchanges and domestic achievements in education, science and technology, and cultural and public health undertakings, the national economy was strengthened. In 1988, there was impressive growth in the Chinese economy. The gross national product (GNP) grew by 11.2070 reaching $373.4 billion; 2 the national income grew by 11.4070 to $310.9 billion. The major problem in the Chinese economy was the imbalance between high demand and insufficient supply. Chronic shortages resulted in price increases and high inflation, which averaged 19% for China as a whole and about 30% in urban areas. Macroeconomic stability took precedence over market-oriented reform initiative. Because of rapidly growing inflation, the Government re-imposed price controls and rationing in major cities in the fall of 1988. China continued to be a major world producer of minerals, metals, and fuels. Output of the principal commodities continued to rise. The largest in-crease in production was salt which rose 24% in output in 1988; followed by sulfuric acid, 14%; cement, 12%; soda ash, 9%; caustic soda, 7%; and steel, 6%. For fossil fuels, the increase in output of natural gas was 14% in 1988; followed by coal, 3%; and crude oil, 2%. The output of electricity by thermal-fired powerplants rose by 9% while that for hydroelectric power-plants rose 7%. Although China's overall energy output has increased annually since 1980, the growth in demand continued to outstrip the supply.

Jan 1, 1990

Entering June, U. S. producer pricing of 99.5 percent unalloyed aluminum ingot was divided at 53-57 cents per pound. The Kaiser Aluminum and Chemical Corp. took the initiative and raised its June 1 ingot values by 4 cents to 57 cents. Consolidated Aluminum Corp. announced plans to increase ingot prices by 4.5 cents per pound to 57.5 cents per pound effective May 15. Dealers increased their May ingot quotes by 1.5-2 cents to 50-50.5 cents. CADMIUM While producers in the United States kept May cadmium at $2.25-$2.50, dealers increased their quotes by 15-30 cents to as high as $2.15.

Jan 1, 1978

By L. G. Marshall

This report presents a cross section of the sand and gravel operations in the Minneapolis-St. Paul area. The study covers individual operations, economic problems peculiar to the industry, glacial geology of the area and its effect upon the grades and types of products, and past, present, and future trends of the expanding population and its effect upon the industry.

Jan 1, 1963

By L. G. Marshall

This report presents a cross section of the sand and gravel operations in the Minneapolis-St. Paul area. The study covers individual operations, economic problems peculiar to the industry, glacial geology of the area and its effect upon the grades and types of products, and past, present, and future trends of the expanding population and its effect upon the industry.

Jan 1, 1963

By Robert E. Manning

At present, a need exists for more effective noise control in the coal-mining industry. In particular, new muffler designs with the required acoustic performance are needed for percussive pneumatic drills. Accordingly, the U. S. Bureau of Mines issued a contract to USS Engineers and Consultants to design a muffler capable of attenuating the noise from the air exhaust of a pneumatic drill. The specific objective of the contract was to design and deliver a prototype muffler that would attenuate the air-exhaust noise to 90 decibels on the A scale (90 dbA). The test drill used in this investigation was one used for roof-bolting purposes in coal mines. Using the combined approach of analysis by digital-computer program and experiment by simulated-noise tests, three prototype mufflers were designed and constructed at U. S. Steel Research. The mufflers consisted of a variety of resonator chambers and expansion-contraction chambers, and were of the following sizes: A muffler with a 3- by 5-inch elliptical cross section and about 8 inches in length. A muffler 5 inches in diameter and about 5-1/2 inches in length. A muffler 5 inches in diameter and about 10-1/2 inches in length. These mufflers were subjected to laboratory tests to determine their effectiveness in attenuating exhaust noise, mechanical noise, total drill noise, and simulated noise. All mufflers reduced the exhaust-noise level by about 25 dbA - from about 115 dbA without a muffler to below 90 dbA with a muffler - and thus were successful in meeting the contract objective. Field tests were conducted with the three prototype mufflers at U. S. Steel's Robena No. 4 Mine, and no icing problem was encountered. A fourth prototype muffler was designed to fit around the leg of the pneumatic drill. Tests showed that this kidney-shaped muffler also reduced the air-exhaust noise to below 90 dbA.

Jan 1, 1973

By J. J. Geraghty

U.S. Bureau of Mines researchers investigated the development of an innovative transport system for underground coal mining. A one-half commercial-scale bench model was constructed. Novel magnetic levitation (mag-lev) technology was developed. Frictionless and contact-free transport of a prototype materials container and payload has been demonstrated.

Jan 1, 2010

By Floyd C. Bossard

Major air-cooling facilities have been installed and are operating underground in U.S. copper mines (at Butte, Montana and Superior, Arizona), South African gold mines, European coal mines, Zambian copper mines, Kolar gold mints in India, Coeur d'Alene mines of Idaho, plus other locations. Mining districts that utilize spot cooling and local air-cooling facilities would increase the above listing many times. The principal objectives of underground mine air cooling systems are to; 1. Extract heat and water vapor from the mine air and provide for their removal from the mine via (a) water pumped to surface or (b) discharged mine exhaust air. 2. Provide acceptable artificial ambient conditions for efficient working mine development and production areas. 3. Recondition used air, thus supplementing the limited mine ventilation balance. In deep South African gold mines, when rock temperatures exceed about 105°F, cooling of underground air becomes necessary for the poorly ventilated sections of the mine. By U.S. standards, air conditioning in poorly ventilated mines usually commences when the virgin rock temperature exceeds 100°F. On the other hand, well ventilated deep vein-type mines in the U.S. have been able to forego general cooling of mine air until the mines have been extended to such depths that the virgin wallrock temperatures have exceeded 115° - 120°F. It must be noted that spot-cooling of selected development headings may be required in many mines where rock temperatures exceed 100°F. Such local air-cooling practices permit the driving of long headings for exploration or extended development prior to holings which result in establishment of primary ventilation circuitry. The following summary reports on current practices of cooling and dehumidifying mine air. General system descriptions with important details will hopefully permit the reader to gain an understanding of the subject. A list of references is provided for this serious investigator who desires a more thorough knowledge-base and who is responsible for the design of a mine air-cooling system.

Jan 1, 1973

By John S. Hutchins

Two potential modified in situ methods are described for recovering the 68% "unrecoverable" hydrocarbons in oil reservoirs. For the 300 billion barrels of conventional light crude a Drip Drainage system is suggested by mining underneath a reservoir and producing from below by controlled gravity flow. For the 200 billion barrels of heavy or viscous oil and tar sands deposits a Flip Flop process is described using surface flooding with hot water saturated with surfactant and weighting additives. Mining engineering description of shafts and tunnels required are included as is discussion of the tunnel proximity to a reservoir. Petroleum engineering flow equations to describe production rates and candidate reserve areas of the U.S. are described. DCF economics are provided to indicate that current oil prices may be sufficient to commercially develop these recovery methods.

Jan 1, 1978

By Sidney Katell, JOHN H. FABER, BRYCE L. MADDOX

The information abstracted from the various publications appeared in the magazines under such headings as Business and Industry , Chemical Engineering Developments , Companies in the News , Headlines of the Month , Industrial News , Industry , Refining and Gas - Processing News , Refining News , What's Happening , and others . Although most items are related to chemical and petroleum plants , a few pertain to related fields , such as markets , drilling costs for petroleum , and field prices of crude oil . Certain articles discuss various aspects of cost -estimating procedures or description of processes . Cost bibliographies prepared by other groups are discussed in items 70 and 271. The two references can be considered as supplemental to this report , since the amount of overlap in the contents is insignificant .

Jun 15, 1957

During the period January 1, 1977 through July 31, 1977, 5 percent (264,000 tons) of U.S. capacity was closed due to power curtailments in the Pacific Northwest because of the shortage of water. During July, one plant in Tennessee cut production by 50,000 tons annually due to a power reduction by the Tennessee Valley Authority. Full capacity production was resumed at a West Virginia smelter during September. If demand for aluminum is strong it seems likely that aluminum supply during the remainder of 1977 and in 1978 will be tight. The price was increased 3¢ per pound to 51¢ per pound effective March 28, 1977, and by an additional 2¢ per pound to 53¢ per pound, effective July 5, 1977. New projects and expansion of existing facilities are planned by Australian aluminum companies over the next 2 to 3 years. The companies listed have committed themselves to spending approximately A$801 million: Alcoa of Australia Ltd. -New alumina plant at Wagerup, south of Perth. Darling Ranges bauxite is located near the proposed project. A$650 million. Coma 1 co Industries Pty. Ltd. -Increase bauxite mining capacity and upgrade or replace other facilities at its Weipa mines on Cape York Peninsula region of Northern Queensland. A$81 million. Alcan Australia Ltd. -Expansion program that will increase capacity of the Kurri Kurri aluminum smelter north of Sydney about 50 percent, and improvement of other facilities at the plant. A$70 million.

Jan 1, 1977

The revised inspection standards or recommendations herein have been prepared for use in Federal inspection of bituminous-coal and lignite mines. They succeed a compilation of similar standards published as Bureau of Mines Information Circular 7268 in December 1943 and employed as a guide in Federal inspections since that time. Important alterations and additions have been made because of changes in mining, practice and temporary shortages of some safety equipment; moreover, several previous standards have been found not generally applicable and have accordingly been deleted. Mining methods and equipment continue to change, and new hazards and new safeguards are introduced. Consequently, these standards are subject to revision from time to time. Questions from the coal-mining industry regarding these standards and suggestions as to changes and additions thereto will be welcomed and considered carefully when the next revision is made. Many constructive criticisms from the mining industry have been considered in preparing this edition.

Jan 1, 1945

By G. W. Jones

One of the major activities of the Bureau of Mines is the promotion of safety in mining and other industries, In this connection, the Bureau determines the explosion hazards' of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. Many dangers are likely to confront men who must enter a building immediately after it has been damaged. Rescue workers must watch constantly for common gases and vapors that may be present in dangerous concentrations in and about demolished, buildings. Fuel gas is the most common source of danger, although refrigerants, gases from furnaces, flues, fires, sewers, and industrial processes, and gas from bomb, explosions in confined places also constitute definite hazards. To rescuers and trapped casualties, these gases offer the hazards of (1) explosion, (2) toxic effects, including asphyxiation and death, and (3) displacement of air so that the oxygen content of the atmosphere is reduced to or below the danger level.

Jan 1, 1944

By Alice M. Chieruzzi

This Country Documentation Report presents the development of economic indices for Zambia for the period from 1970 through 1981. The work done through the Bureau of' Mines, Minerals Availability Program, under Contract number J0225001. This contract calls for the development of twelve index time series describing factor input costs in the mining sector of 95 countries. The twelve index time series describe the costs of: 1) mining wages, 2) construction wages, 3) equipment and repair parts, 4) bits and related steel, 5) timber and lumber, 6) fuel, 7) powder and blasting agents, 8) tires, 9) construction materials, 10) industrial materials, 11) transportation, and 12) electrical power. These indices combined with weight factors being developed by the personnel of the Minerals Availability Field Office (MAFO) of the Bureau of Mines in Denver, Colorado, will be used to perform instantaneous updates of all costs relating to the mining industry. The indices were developed primarily for use in the Bureau's Minerals Availability Program in assessing the worldwide availability of nonfuel minerals.

Jan 1, 1983

By G. R. Peterson

To determine the availability of lead and zinc from demonstrated resources, the Bureau of Mines evaluated 235 mines and deposits in 31 market economy countries. Of the 235 mines and deposits evaluated for this study, 186 were evaluated as zinc operations, 30 as lead operations, and 19 as copper operations. Demonstrated lead-zinc resources of market economy countries in 1981 were approximately 4.3 billion metric tons (t) of ore containing 221 million t of zinc and 97 million t of lead. Of these amounts, approximately 154 million t of zinc and 70 million t of lead are estimated to be recoverable. The analyses indicate that demonstrated resources in market economy countries should be sufficient to satisfy projected demand for primary lead and zinc through the balance of the century. The U.S. lead industry will continue to have a comparative advantage over the rest of the world industry, barring any drastic increase in the cost of compliance with pollution control regulations. It appears that the comparative disadvantage faced by the U.S. zinc industry will probably intensify owing to the relative quantity of lower cost zinc resources in other countries, especially Canada, Australia, Mexico, and Peru.

Jan 1, 1985

This report presents the results of a study for the Bureau of Mines to compare loan terms for non-fuel mineral projects in developing countries, from various International Financial Institutions (IFIs), and from private sector commercial sources. The study compares IFI and commercial loan terms for seven mineral projects in developing countries. The International Financial Institutions represented are: ? International Bank for Reconstruction and Development (World Bank) ? International Finance Corporation (IFC) ? Inter-American Development Bank (IDB) ? Asian Development Bank (ADB) ? International Monetary Fund (IMF) In addition, the costs of financing for these mineral projects were compared with the costs of long-term debt to the five largest U.S. mineral producers.

Jan 1, 1986