Search Documents

By W. R. Reed, J. A. Organiscak

Haul trucks have the potential to generate large amounts of respirable dust. This respirable dust has been shown to be a health hazard to personnel, especially if it has a high silica content. Lack of dust sampling data from haul trucks prompted the completion of a study to quantify respirable dust concentrations. These field studies were conducted measuring instantaneous respirable dust at stationary locations from passing haul trucks at a stone quarry and at a coal mine site. Fugitive dust levels from haul trucks were analyzed to characterize dust dispersion. This analysis indicates safe following distances for haul trucks and other heavy equipment to avoid overexposure of respirable dust from the lead haul truck.

By Terry G. Montgomery, Eric S. Weiss, John E. Going, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine (LLEM), and after laboratory explosions in the PRL 20-L chamber and the Fike I m3 chamber. The dusts studied included both high- and low-volatile bituminous coals. Low temperature ashing for 24 h at 515 °C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as, or higher than the initial incombustible content. The MSHA alcohol coking test was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared with the initial dust loadings to determine the transport distance of dust during an explosion. All these data will be useful in future forensic investigations of accidental dust explosions in coal mines, or elsewhere.

By E. R. Spencer, E. Reeves

National Institute for Occupational Safety and Health (NIOSH) researchers conducted an investigation to quantify sound levels and to determine the amount of sound reduction provided by engineering noise controls installed in a talc processing plant. Baseline sound level and sound intensity measurements were performed at the plant and the measurement locations were recorded for comparison to post-control measurements. Follow-up measurements were then made at the same locations after the initial noise controls were installed. The plant subsequently decided to implement additional noise controls and the researchers returned to conduct measurements for a final analysis of all noise controls. The most significant results showed a sound level reduction in the main mill area from a range of 93-104 dB(A) down to 90-94 dB(A), and a total sound power level reduction of 21 dB(A) for air classifying mill 3.

By John K. Owens, Wayne L. Howie

Mobile roof support (MRS) machines are used as roof support during pillar recovery in retreat operations in lieu of wooden posts, cribs, or hydraulic props. A Mine Safety and Health Administration-permissible load rate monitoring system was developed for the MRS by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. The system uses a dedicated embedded processor to monitor changes in pressure inside the hydraulic cylinders of the MRS through multiplexed data acquisition channels and converts these pressure changes to load rates that sequentially activate three load-rate-indicator lights mounted on the machine. Each light represents a different loading rate to alert mine personnel to dangerous conditions during pillar extraction.

By D. Harrington

Seldom, if ever, has any mining hazard presented itself that some method has not been devised to control it to some extent; the degree of success of such control depends largely upon the intensity of desire to prevent suffering, injury, and death. The economic saving to be realized and the more definitely this is realized by all concerned, the more quickly and effectively will the hazards be handled is an important incentive to prevention of accidents. Preventing coal-mine explosions is by no means a complex problem; all that is necessary is sensible, conscientious, sustained effort. The fact that explosions can be prevented has been well-demonstrated by the record of the post few years; the average annual death toll from explosions for the 5 years 1906-1910 was 438, and for the 20 years prior to 1929 it was 265: during the past 4 years an average of only 32 deaths per year resulted from this cause, although the annual production during that time varied but slightly from that of 1906-10. This is a truly remarkable reduction, and if other types of mine accidents had been reduced in the same ratio only about 300 would be killed annually in our mines instead of the nearly '1,300 killed in 1936 and the approximately 2,000 killed annually for many years. Although frequency of occurrence of explosions has not lessened greatly during the last decade, their severity decreased markedly, which would indicate that effective means are being taken to prevent the spread of explosions, even though ignitions and their causes are not being handled nearly as effectively as they might or should be handled. Several large coal-producing States, which in the past have experienced numerous disastrous explosions, have been free from such disasters for continuous periods as long as 8 years in the relatively recent past. The application of rock dust to underground surfaces has been an important factor in preventing widespread explosions; some of the mast dangerous mines have been rock-dusted fairly adequately, and this has been amply repaid in the reduced severity of explosions, as heretofore indicated; however, many have applied rock dust apparently without giving much consideration to the amount required to prevent

Jan 1, 1938

By A. G. Starliper

The Bureau of Mines made laboratory investigations to determine the feasibility of utilizing fine tungsten wires to reinforce a number of nonferrous metals and alloys and a superalloy, S-8l6. The composites of tungsten filament and metals were chosen to attain elevated temperature strength and corrosion resistance. Oriented clean or precoated tungsten wires were incorporated with the other metals by extrusion, swaging, and infiltration casting. Although widely varying characteristics were found in the composites, none were considered satisfactory for high-temperature use, chiefly because of reactions between the matrix metal-tungsten surface. Diffusion, solution, and chemical reactions between matrix and tungsten wires were sufficiently slow for some combinations, such as 15 v/o 8-816, to exhibit increased high-temperature strength for a limited time. A few metals failed to wet or bond to the tungsten surfaces, while a few responded after precoating with a third metal.

Jan 1, 1968

By B. W. Dunning

This paper describes studies conducted by the Bureau of Mines to achieve its goal of developing methods for increased recovery and utilization of valuable constituents in a wide variety of domestic and industrial wastes, In this particular study, 36 units of obsolete electronic equipment from military aircraft were disassembled into their modular components by hand to determine materials distribution. Further modular disassembly into individual parts was used to identify metal composition. After identifying the metals in some of the more difficult to dismantle modules, similar modules were grouped together, shredded, mechanically separated, and using metal composition data from hand separation, classified along with the hand-separated materials. Although this equipment is normally classified as law-value iron-bearing aluminum, data were obtained that indicated the potential for moderately higher value classification. The electronic units were classified as to precious metals, copper, iron, and aluminum contents, and scrap values were estimated.

Jan 1, 1980

By Gerald L. Finlinger

This Bureau of Mines publication reviews underground methane drainage programs being conducted in various coalbeds. Equipment used in drainage programs such as drills, underground pipelines, and methane monitoring systems is described.

Jan 1, 1980

By Abdurrahman Cetinbas

The effect of water infusion on the flow of methane and on the production of dust was investigated at an active face in the Pittsburgh coalbed. The average total flow of methane at the face decreased by approximately 79 percent, whereas the flow from the ribs increased about 24 percent after infusion. On the day after infusion, dust concentrations appear to have been reduced; however, the presence of large quantities of rock dust obscured the results on the following days.

Jan 1, 1972

By E. D. Calvert

The room temperature tensile properties of commercially pure titanium and seven titanium alloys prepared by skull casting were determined in the as-cast and heat-treated conditions. Data were compared with property data from tensile tests on wrought alloys of the same compositions in the as-worked and heat-treated conditions. The alloys evaluated were Ti-5Al-2.5Sn, Ti-6Al-4V, Ti-6Al-4V-lSi, Ti-6A1-2Sn-4Zr-2Mo, Ti-6A1-6V-4Zr-4Mo, Ti-6A1-6V-2Sn, and Ti-11.5Mo-6Zr-4.5Sn. Test specimens were prepared from both static and centrifugal castings and from plate fabricated by forging and rolling vacuum-melted ingots. The data indicate that the alpha and alpha-beta alloys have strength properties in the as-cast condition that are reasonably close to the strength properties of their wrought counterparts in the as-worked condition. An exception to this was the Ti-6A1-6V-4Zr-4Mo alloy for which insufficient data were available to form any firm conclusions. Fine-grained cast structures of Beta III (Ti-11.5Mo-6Zr-4.5Sn) were shown to be generally stronger in the as-cast condition than the wrought alloy in the as-worked condition except for the yield strength of one structure that was unusually low. Heat treatment of this alloy produced properties that were unpredictable. Indications are, however, that optimization of heat treatment parameters for each cast structure could produce strength properties equal to that of wrought materials.

Jan 1, 1974

By H. G. Wolfhard

The propagation of explosions through short cylindrical channels has been investigated by the Bureau of Mines. In the experimental apparatus set up by the Bureau, a single such channel formed a connection between a small explosion vessel in which a gaseous explosion was initiated and a larger, partly enclosing, explosion vessel filled with suitable gaseous mixtures; the larger vessel permitted observation to determine if an explosion was induced therein by mass, energy, and species transfer through the channel, as a result of tie initial explosion, It has been found that transmission of flame through to channel is not an essential to induce the second explosion, for hot gases from an extinguished explosion are able to ignite cold combustible mixtures in the larger vessel. The schlieren patterns of flames or hot burned gases emerging from a channel into the explosion chamber were photographed. These show, in most instances, that vortexes of hot gas ejected from the jet into the cold explosive mixture are responsible for ignition. The study has practical significance in problems of rendering electrical equipment safe for use in potentially flammable atmospheres, INTRODUCTION The propagation of flames through cylindrical or annular channels has practical importance in flameproofing electrical equipment and for flame traps. Much practical work has been done to determine the minimum safe breadth of flanges and the maximum safe gap between the flanges that will permit venting an electric motor without allowing flames to pass.

Jan 1, 1959

By Joel N. Van Sant

THIS REPORT describes the occurrence, mining, and use of refractory clay in Colorado within Region III of the Federal Bureau of Mines, which includes the States of North arid South Dakota, Nebraska, Wyoming, Colorado, Utah, New Mexico, and Arizona. Field work by the Bureau of Mines, United States Department of the Interior, included examination of active and abandoned refractory-clay mines as well as a reconnaissance survey and sampling of numerous clay-bearing formations exposed in Colorado. Information from the survey and the sampling will help guide private industry in its search for virgin sources of refractory clay. Library research of published and unpublished reports from various Federal, State, and private sources was conducted during the early phase of the investigation. Most of the refractory clay mined in the Denver-Golden district of Colorado is not used for refractory purposes but is blended with other clays in the manufacture of structural clay products. The predominantly flint-clay de-posits in the Pueblo and Fremont County districts are mined and utilized chiefly in fabricating refractory products.

Jan 1, 1959

By W. L. Cooley

The report provides a detailed analysis of 23 electrical accident countermeasures contemplated for use in the metal/non-metal mining industry. The costs and potential benefits of implementing groups of these countermeasures are estimated, and methods arc outlined by which the operator ran choose countermeasures in an effective manner. The analysis is based largely on an extensive electrical accident event tree which is developed in detail. For those countermeasures which are not currently technically feasible, several prototype devices were developed to help speed development. These included a trolley arc eliminator and a safer mine electricians multimeter.

Jan 1, 1982

By Michael D. Balen

The Bureau of Mines (Bureau), in cooperation with the Alaska Division of Geological and Geophysical Surveys (ADGGS), conducted field investigations from 1987 through 1989 in the 5.7 million-acre Valdez Creek Mining District (VCMD) in south-central Alaska. The objective of the VCMD investigation was to evaluate the mineral resources and the mineral development potential of the mining district. The investigation was part of the Bureau's continuing statewide mining district evaluation program. Nineteen new mineral occurrences were identified as a result of this investigation. Reconnaissance placer sampling resulted in the identification of 10 previously unreported occurrences that primarily contain gold, however, some contain subsidiary platinum-group metals and/or tin. Reconnaissance lode sampling resulted in the identification of two gold-silver occurrences, three platinum-group metal occurrences that contain elevated quantities of subsidiary chromium, nickel and/or cobalt, three copper occurrences that contain subsidiary molybdenum or zinc, and one zinc occurrence.

Jan 1, 2011

By Eldon C. Pattee

Reconnaisance samples of reported beryllium occurrences in Idaho, Washington, Montana, and Oregon were chemically and spectroscopically tested in a mobile laboratory. The two predominant types of occurrences were green beryl associated with Cretaceous intrusions and disseminated aquamarine associated with Tertiary intrusions. Although the beryllium content of known deposits in the Northwest is too low for economic development at present, total submarginal-grade beryllium resources in pegmatites are estimated to be 570,000 to 1,870,000 tons containing 0.024 to 0.167 BeO. A potential source of 500,000 to 700,000 tons of beryllium-bearing tactite in Idaho and Montana averages 0.033 to 0.080 percent BeO.

Jan 1, 1968

By Robert P. Bruno

This report covers the study of the feasibility of using a hand-held infrared viewer as a methane indicator to observe methane gas at the face of an underground coal mine. The objective of this program was the development of a hand-held device to remotely detect the presence of concentrations of methane gas in underground coal mines. Convenient "mapping" of methane from a remote location would allow rapid and safe corrective procedures for working personnel. Modified commercially available equipment was evaluated both in the laboratory and in a working mine. Although readings were obtained and the general principle of operation demonstrated, the power levels necessary, and protective enclosures required, would raise the weight of the instrument beyond practical limits of portability. Based on currently available technology, it is the conclusion of the investigations that a practical, portable, hand-held visual methane indicator is beyond the state-of-the-art. The recommendation was, therefore, made that work be suspended, and the results and data compiled and presented in a final program report.

Jan 1, 1979

By James L. Ash

This report contains the results of a technical and economic evaluation of conceptual systems for the underground mining, rubblization, and in situ retorting of deep oil shale deposits. Study efforts were first directed towards evaluation of the applicable geology, associated minerals, rock mechanics, in situ retorting, access mining, ventilation, rubblization, safety, and environmental impact factors. Conceptual systems were synthesized and then evaluated against these factors from both a technical and limited economic viewpoint. The results of these evaluations were then analyzed and, based upon this analysis, the following two systems were selected for further study: System II: Room and Pillar-Vertical Drill and Blast System IV: Tunnel Boring-Horizontal Ring Drill and Blast Due to the large number of variables to be considered, a computer program was developed and utilized to provide data for the cost trade-off studies and economic analysis. Results of the early computer runs indicated the value of the tool available? in the computer program and led to an extension in the contract to determine the sensitivity of the systems to several of the more apparent significant variables. These results in turn led to a refinement in the design assumptions and a better understanding of the technical and economic options available to an owner-operator of a Vertical Modified In Situ Shale Oil Extraction System. This report is submitted in fulfillment of the requirements of Contract Number 50241073 by Fenix & Scisson, Inc. to the Denver Mining Research Center, United States Department of the Interior, Bureau of Mines. Work was completed as of November, 1976.

Jan 1, 1976

By M. C. Irani

The Bureau of Mines, in cooperation with the Mine Safety Appliances Co., has developed a continuous-recording methanometer utilizing a catalytic combustion detector. The methanometer, which is presently operating at 22 exhaust fans at 14 mines in the Eastern coalfields, is reliable and simple to install, operate, and maintain. The instrument and the details of its installation and calibration are described. Analytical data obtained by infrared spectrophotometer and gas chromatograph are presented to substantiate its re liability.

Jan 1, 1974

By Geo. S. Krueger

This paper, describing mining methods and costs at the Judge mine Park City, Utah, is one of a series being prepared by the Bureau of Mines on mining practices in the United states. ACKNOWLEDGMENTS The writers acknowledge the assistance of E. D. Gardner, supervising engineer, Southwest Experiment Station, Bureau of Mines; Paul H. Hunt, mine manager, Park Utah Consolidated Mines Co.; Wm. Osika, chief mine accountant; and Eric Neilson, assistant master mechanic of the mine.

Jan 1, 1938

By Wesley T. Holmes

This report describes the first phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected slag compositions in the titania-alumina-silica-calcia-magnesia system. Both the melting-holding-quenching method and the hot-stage microscope method were used in the tests. Liquidus temperatures of slags studied ranged from 1,217° to 1,667° C. The lowest liquidus temperature of the slags occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. Liquidus temperatures were also lowered when Si02 was substituted for Ti02 plus Al2O3 when CaO and MgO levels were held constant. Improved methods for the measurement of liquidus temperatures on very small samples are described.

Jan 1, 1968