Search Documents

By L. K. Weaver

Bureau of Mines investigated the progressive impact that petroleum (crude oil and condensate) operations in the Gulf of Mexico have had on onshore operations and the expected effect of increasing activities in this area on future petroleum supplies from domestic sources. The data analyzed include capital expenditures, number of wells drilled, success ratio for exploratory wells, daily production per completion, annual producing rates, and oil reserves. The report compares offshore and onshore data and ascertains trends in petroleum industry operations. Observed data and trends indicate that in the near future Gulf of Mexico development and production will continue to increase relative to total U.S. petroleum activity. By 1975 annual oil and condensate production from the Gulf of Mexico is expected to be in the range of 750 million bbl to 1,150 million bbl, and account for approximately 20 to 30 pct of the estimated total domestic production.

Jan 1, 1969

By Sally A. Shoop

Thirty-seven blasts have been monitored using either three or four seismographs, at four coal strip mines and at a limestone quarry. Statistical analysis of the data shows that square-root, cube-root, and site-specific scaling methods predict peak particle velocities with about the same (low) degree of reliability. Some mines have peak particle velocities that are significantly lower or higher than the U.S. Bureau of Mines averages (Siskind et al., 1980). This suggests that the option provided by the proposed regulations (Office of Surface Mining, 1983), to adjust blast designs based on site-specific measurements could be highly beneficial both to operators and to the public. The frequency spectra reveal that the predominant frequencies were generally less than 50 Hz but several blasts had a significant amount of energy up to 125 Hz. In some cases the vibration energy was concentrated at frequencies corresponding to the delay intervals.

Jan 1, 1983

This manual covers the operation and lubrication procedures for the Eimco Pumpable Roof Bolting Machine. This machine meets U. S. Bureau of Mines Schedule 2G Approval. This manual is divided into three major parts: 1. Machine dimensions; 2. operating instructions and; 3. Lubrication. Whenever front or rear, right or left arc mentioned it is assumed that the reader is standing behind the machine looking toward the boom. The boom is at the front of the machine. Safety When leaving machine parked on an incline turn wheels into the rib or block wheels. Do not run over power cables. Make sure your power cable is up out of the way so others can't run over it. Machine has a fire suppressor system for the power unit. The remote actuator (pressure cylinder) is located at the operator's station. Components and service procedures on page 59.

Jan 1, 1976

By Robert H. Peters

This U.S. Bureau of Mines report identifies the types of serious accidents that occur most frequently at small underground coal mines and describes the strategies that could help prevent these accidents. A wide variety of methods for improving safety are suggested, including improvements in the design of equipment, work procedures, work schedules, safety programs, and emergency response plans, as well as techniques for diagnosing the potential hazards associated with new technologies and work procedures. Some of the papers in this volume focus on preventing specific types of mining accidents--ones associated with materials handling (primarily back injuries), equipment maintenance, improper machine guarding, and ground failure during retreat mining. Although the recommendations in this volume are heavily influenced by research performed at underground coal mines in the Appalachian coalfields, most of the papers contain advice that is equally pertinent to almost any type of mine.

Jan 1, 1994

By A. J. Farstad, R. F. Kehrman

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped driers in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light- weight and inexpensive.

Jan 1, 1979

By A. J. Farstad

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped mines in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light-weight and inexpensive.

Jan 1, 1979

By Charles L. Kimbell

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in the country and regional reports that comprise the five other sections of 1991 Minerals Yearbook-International Review, it is clearly impossible to cite all sources of information used in its presentation, but some recognition is due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible, without the efforts of the personnel of national mining and geological agencies throughout the world. Information that they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, appreciation is expressed to the multitude of persons employed by these agencies.

Jan 1, 1993

By Ronald F. Balazik

The introduction of "high-tech" materials such as new polymer composites presents significant competitive challenges and opportunities in conventional mineral markets. Moreover, rapid advances in materials science are critical to the resolution of important economic and strategic issues, including national competitiveness and import dependence. This Bureau of Mines study examines the displacement of conventional nonfuel mineral materials by certain new materials, specifically advanced plastics and ceramics. Analyses of substitution by plastics are conducted for five major U.S. industrial sectors: motor vehicle manufacturing, aerospace applications, building and construction, packaging, and heavy machinery production. Based on interviews with more than 60 scientists, executives, and other professionals engaged in materials development and sales, forecasts of substitution by plastics during the 1990's are made for aluminum, steel, and glass. In addition to these forecasts, study findings identify key factors that will influence the emergence of advanced materials in the next decade.

Jan 1, 1987

By F. A. Rutledge

The Millet copper deposit is on the north shore of Iliamna Lake in southwestern Alaska. Copper mineralization occurs in a zone of altered limestone .adjacent to and intruded by a diorite porphyry with some diabase facies. During 1949 and 1950, the Bureau of Mines investigated this prospect as a part of the U. S. Department of the Interior program in Alaska for the development of critical and strategic minerals. Field work was begun August 8, 1949; it was recessed November 28, 1949, because of inclement weather. The work was resumed Nay 28, 1950, and completed July 3, 1950. The program of investigation by the Bureau of Nines included topographic surveying, machine and hand trenching, diamond drilling, and sampling the zones of mineralization. This report outlines the general geology of the area, gives a description of the deposit, and contains the factual data resulting from work by the Bureau of Mines.

Jan 1, 1952

By W. M. Dressel

The Federal Bureau of Mines has obtained data by differential thermal analysis of the various minerals that represent the nation's resources in manganese. These data are supported by X-ray diffraction analysis, chemical analysis, mineralography, and optical mineralogy, and provide fundamental information on the response of each mineral to thermal treatment in oxidizing, reducing, and neutral atmospheres. The information can be applied advantage¬ously in the identification of manganese minerals. Its greatest potential value, however, lies in the application of the quantitative data on the reaction temperatures, rates, and products to the more efficient extraction of manganese from U.S. ores. Thermal analysis curves are presented for certain manganese minerals, namely hausmannite, bixbyite, braunite, pyrolusite, lithiophorite, cryptomelane, hollandite, manganite, rhodochrosite, and rhodonite. The original minerals and the products of their thermal decomposition were identified by X-ray diffraction analysis, supplemented by chemical analysis and mineralogical identification.

Jan 1, 1961

By Fei-chiu Huang

The principle of time domain reflectometry (TDR) is being used by the U.S. Bureau of Mines to monitor strata displacements induced by mining. The Northwestern University TDR Signature Analysis (NVTSA) Program was developed under contract with the Bureau to allow for visual comparison of three TDR waveforms quickly and easily. This program is interactive, and on-line help is available. The Northwestern University Remote Control TDR Data Acquisition System and Modification of Tektronix SP232 Host Application Program (NUMOD) was then developed to allow acquisition of TDR wave-forms from a remote cable tester via modem. The NUMOD system utilizes commercially available software while the NUTSA program is available from the Bureau. This report begins with a discussion of TDR principles followed by a description of the NUMOD system. An interactive example of signature analysis is then used to demonstrate features of the NUTSA program.

Jan 1, 1993

By David E. Swanson

The U.S. Bureau of Mines undertook a basic investigation of collimated abrasive water-jet behavior because a more complete understanding of the fundamental process may lead to further technical advances. Laboratory experiments used 2-mm water-jet nozzles and new entrainment apparatus to analyze collimated abrasive water jets operating under varied conditions. Maximum water pressure was 69 MPa to permit use of conventional hoses with a burst-to-operating-pressure ratio of 4. Nozzle and induction line pressures, abrasive induction rates, and jet reactive thrust forces were recorded for each operating condition. Average jet velocity and power were determined from component mass flow rates and reactive thrust force measurements. Relative velocity and cross-sectional distribution of abrasive particles were determined using impact analysis techniques. Other jet characteristics were determined photographically. Properties of free water jets, collimated water jets, and collimated air-water jets were determined for comparison.

Jan 1, 1989

By Robert H. Peters

This U.S. Bureau of Mines report identifies the types of serious accidents that occur most frequently at small underground coal mines and describes the strategies that could help prevent these accidents. A wide variety of methods for improving safety are suggested, including improvements in the design of equipment, work procedures, work schedules, safety programs, and emergency response plans, as well as techniques for diagnosing the potential hazards associated with new technologies and work procedures. Some of the papers in this volume focus on preventing specific types of mining accidents-ones associated with materials handling (primarily back injuries), equipment maintenance, improper machine guarding, and ground failure during retreat mining. Although the recommendations in this volume are heavily influenced by research performed at underground coal mines in the Appalachian coalfields, most of the papers contain advice that is equally pertinent to almost any type of mine.

Jan 1, 1994

By L. Hoogenboom

Under contract (H0232044) to the U.S. Bureau of Mines, Mechanical Technology Incorporated made an experimental investigation of the feasibility of measuring the load in roof bolts using a magnetostrictive sensor. The program was aimed at developing an inexpensive, moderately accurate, load-sensing element suitable for permanent installation and use underground. A combination of a cylindrical load-carrying sleeve under the bolt head and 3 removable circular multipole inductive sensor around the sleeve was tested. Program tasks included: design and fabrication of several sensors; design and manufacture of a large number of experimental sleeves; definition of electronic instrumentation specifications; design and manufacture of electronic sensor readout; and evaluation and testing of many sensor-sleeve combinations. Sleeves of different materials, various lengths, diameters and areas - with and without various nickel coatings -were combined with several experimental inductive sensors that were operated over a wide range of carrier frequencies.

Jan 1, 1974

By Michael Rieber

Among the principal gathering/distribution systems for coal is over-the-road trucking. Where alternative trunk line modes such as barge or rail links are weak or nonexistent, trucks may, particularly for relatively short line hauls, act as substitutes. Their major application, however, appears to be in connection with smaller mines or coal users particularly where terrain problems are significant. Truck use has increased as rail lines have been abandoned or suffered neglect. For example, in 1956 about 38 percent of the coal transported in eastern Kentucky and about 8 percent of the coal moved in western Kentucky went by truck. By 1975, the percentages were almost 77 percent and 26 percent, respectively [4,U-11]. While rail route .limitations and deterioration played a part in the change, increased emphasis on road building, particularly during the 1950's and 1960's, and improved truck load capacity and efficiency were also important.

Jan 1, 1977

By Alan A. Campoli

The U.S. Bureau of Mines conducted research to characterize longwall gob loading under bump-prone geologic conditions. Bureau-designed stress meters were installed in the floor rock beneath two longwall panels and coal pillars in the gate road between them. Gob and gate road pillar stress was monitored continuously by a state-of-the-art data acquisition system. The timing of the final destruction of the abutment pillar's load-bearing core was optimal, since the pillar is located between two gob areas and no longer of significant importance for ground control. Maximum stress was observed immediately in front of the longwall face, and this pressure quickly dropped as the face moved past the instruments. The center of the longwall panels regained significant overburden load, while the instruments located less than 100 ft from the edge of the panel showed little or no increase in pressure due to gob reloading.

Jan 1, 2010

By S. P. Kinney

The efficient operation of a blast furnace is primarily dependent upon efficient contact between the descending stream of solid materials and the ascending stream of gas. The United States Bureau of dines is conducting a program of research dealing with the interior of the present-day furnace. The work is being carried oat by.(1) observations on commercial furnaces end (2) experiments in the laboratory. Through the courtesy of the officials of the Illinois Steel Co. it was possible to make a detailed investigation of the interior of the shaft of Number.4 furnace at the company's South Works, South Chicago, Ill. The experimental work is to be reported in a U. S. Bureau of Mines bulletin which will include the results of several thousand observations on the interior of the shaft of this furnace. Such of the data as are presented later in this paper constitute only a brief summary.

Jan 1, 1929

By Michael A. Anuta

This report describes the potential for utilization of satellite observations for remote sensing of mine waste disposal areas. Four study sites consisting of metal and nonmetal mining areas in different climatic and physiographic regions of contigous United States were used in this investigation. The mine waste disposal sites consisted of mining of phosphates in Florida, copper in Arizona, silver in Idaho, and coal in West Virginia. Landsat satellite multispectral scanner observations were used together with aerial photographs, ground surveys, U.S. Geological Survey maps, and other ancillary information. Landsat digital data were categorized using automated supervised classification algorithms and an image analysis system. Detailed description of automated classification techniques employed and the accuracy attained is provided together with the results of manual interpretations. The inventory of areas distrubed for phosphate mining and a change detection investigation for-Polk County Florida were also undertaken during this study.

Jan 1, 1982

By Michael Hood

High-volume, low-pressure water jets have been employed for erosion of loosely consolidated rocks for centuries. This excavation method finds application in specialized circumstances even today. The use of high-pressure, low-volume water jets for rock cutting is more recent and was made possible by the development of high-pressure water pumps. Despite the benefits often claimed for these systems, high-pressure water jets still have not found widespread application. In this report, the U.S. Bureau of Mines has reviewed the various methods that have been employed using water jets to break rock and has focused on one method, termed "jet-assisted cutting," which was determined to be the closest to commercial development. The current state of knowledge based on laboratory and field experiences using this cutting method is reviewed, and possible future developments for this approach to excavation are assessed.

Jan 1, 1990

By G. E. McClelland

As part of its mission to assure an adequate domestic supply of metals essential to the Nation's welfare, the U.S. Department of the Interior, Bureau of Mines, investigated a particle agglomeration technique as a means for improving the flow of leaching solution through heaps of clayey or finely crushed, low-grade, gold-silver ores. Bench-and pilot-scale experiments showed that the percolation rate of cyanide leaching solution was markedly enhanced by mixing the ore with a portland cement binder, moistening the mixture, and mechanically agglomerating and aging the feed prior to heap building and leaching. The rate of gold and silver recovery markedly increased because of the increased, uniform percolation of leaching solution through the agglomerated feed. The use of concentrated cyanide solution instead of water during the agglomeration procedure decreased the leaching time required to obtain maximum recovery. Results of bench-and pilot-scale experiments are discussed.

Jan 1, 1981