Search Documents

By Roy C. Bartholomae

This U.S. Bureau of Mines study found that the performance of the active noise cancellation hearing protector in a reverberant field was mixed. The performance varied when the conditions changed from ideal to nonideal. The active noise cancellation (ANC) component provided substantial additional noise reduction from 125 to 500 Hz for all testing conditions (broadband noise or pure tones both with and without safety glasses). While the ANC under ideal conditions provided additional attenuation from 500 Hz and below, under nonideal pink noise conditions the ANC amplified noise below the 125-Hz third octave band. There was a middle band of frequencies at which the ANC amplified noise levels ranging from 630 to 4,000 Hz. The results for pure tones showed that attenuations were higher but that they followed the same general trend.

Jan 1, 2010

By d&apos, Kathleen J. Amico

THIS SUMMARY appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U .S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed ?mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1965

By Maria I. De Rosa

This report analyzes mine fires for all U.S. underground and surface metal/nonmetal mining categories during 1990–2001 by state and six successive 2-year time periods. Injury risk rates are derived, and ignition source, methods of detection and suppression, and other variables are examined. Fires involving contractors are also included in the analysis. The data were derived from Mine Safety and Health Administration (MSHA)mine fire accident publications and verbal communications with mine personnel. The analysis will provide the National Institute for Occupational Safety and Health, MSHA, and the mining industry with a better understanding of the causes and hazards associated with mine fires and an increased awareness aimed at preventing and reducing fire hazards. It will also form a basis for future fire research programs.

Jan 11, 2004

By R. D. Govier

The U.S. Bureau of Mines has developed a thin-film X-ray fluorescence technique to rapidly determine Cu, Ni, Co, Fe, and Cr in super alloy leach liquors. Total analysis time per sample was less than 15 min, as opposed to several hours for traditional wet chemical methods. Precision and accuracy were checked by replicate analyses of solutions similar in composition to leach liquors, whose analyte concentrations were well known. Coefficients of variation for all elements were found to be less than 2 pet. With the exception of the results for Fe, all relative errors of estimation were also found to be less than 2 pet. Bulk liquids are not introduced into the spectrometer; thus, the potential for damage to the instrument by leakage of corrosive liquids is eliminated.

Jan 1, 1989

By Michael J. Friedel

The integrity of mine structures, such as the roofs, ribs, face and supporting pillars, is difficult to assess beyond the exposed surface. To mitigate potential rockfall hazards, the U.S. Bureau of Mines is assessing the usefulness of Rayleigh wave dispersion analysis to detect damage and stress-relieved zones in mine structures. Classical surface wave dispersion modeling is utilized at both laboratory and field scales in damaged and undamaged material to assess the integrity of a mine pillar and roof. To more fully exploit Rayleigh wave propagation characteristics, derivation of a novel dispersion parameter was conducted using a convolutional model. The development of a suitable Rayleigh wave dispersion system based on insight derived from forward modeling is presented. The application of inverse modeling for damage and stress assessment in the mine environment is also discussed.

Jan 1, 2010

By Daniel Edelstein

Demand for arsenic trioxide increased markedly during 1984 as a result of increased use of arsenical wood preservatives and increased use of arsenicals in agriculture. The increase in agricultural demand was due to a return to production of land with-held from cotton planting under an agriculture program for acreage diversion for some 1983 crops. Supplies of arsenic trioxide were more than adequate to meet increased demand, and prices either declined from, or remained at, the low 1983 levels. In June, ASARCO Incorporated announced plans to close its Tacoma, WA, smelter by mid-1985. Domestic Data Coverage.-Refined arsenic trioxide was produced by two U.S. companies. The major producer voluntarily reported its production to the Bureau of Mines, but to prevent disclosure of proprietary data, the production data have been withheld.

Jan 1, 1985

By William D. Monaghan

The U.S. Bureau of Mines evaluated a teleoperated continuous mining machine for deep mining in thin-seam applications as low as 1 m. Teleoperation increases the safety of mining machine operators because it removes the operator from the face, an area of immediate hazards to safer outby locations. By using teleoperation, the miner can avoid many including unexpected roof falls that can maim or kill miners instantly, methane and coal dust explosions that can be ignited with just a small spark or flame, adverse health effects from miners breathing coal and silica dust, adverse long-term inner ear damage from loud noise pollution, and other hazards related to heavy mining equipment moving about in confined underground roadways. This report presents the surface evaluation results of a teleoperated control system.

Jan 1, 1994

By William K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating the electrochemistry of mineral flotation. A significant need in this area is greater reliability of sensors. The USBM is testing electrolytic methods to clean and condition redox-sensing electrodes to improve the reliability and extend the service life of these instruments in the harsh physical and chemical environment of mineral processing slurries. A novel method for removing scale from fouled electrodes has been developed that includes anodic polarization to 1.2 V versus the Ag/ AgC1 reference potential, followed by brief potentiodynamic conditioning. Laboratory results show that this technique removes calcarious deposits from gold sensing electrodes and returns the electrodes to useful service within approximately 10 min. Mechanical abrasion to remove the scale is thereby avoided.

Jan 1, 2010

Mining officials, as well as members of the Bureau of Mines staff, in their efforts to make mining safer are confronted from time to time pith complicated problems concerning solution of which there is a diversity of opinion. To reduce these differences of opinion as much as possible and to obtain a generally acceptable decision on any mine-safety question, the Director of the U.S. Bureau of Mines established the Mine Safety Board on June 1, 1924- *** to consider questions arising within any divisions of the Bureau that require a definition of tie Bureaus s collective opinion as to safety practices, safety devices, or safety methods for underground operations or open-pit mining. The approved2/decisions shall form the basis of teaching and policy for the Bureau.

Jan 1, 1935

By Michael D. Fenton

The very modest-sized mineral industry of Afghanistan was burdened for another year with problems of internal strife occassioned by the presence of Soviet armed forces. Despite this, production of the few traditional commodities continued, and the mineral industry moved to develop additional mines and plants for both traditional and new products with considerable technical and construction assistance from the U.S.S.R. Among the limited range of mineral commodities for which production was reported, there were no startling changes between 1984 and 1985. Production of both coal and natural gas advanced only slightly, despite substantially higher 5-year plan goals, and cement output was down marginally. Probably the most significant development in 1985 was the Possibility that mine and/or smelter production of copper was initiated during the year.

Jan 1, 1987

By W. P. Stroud

In this U.S. Bureau of Mines report, the conditions required for the direct reconstruction of a tomogram from observed line integrals are examined. Because of the limited access to the working faces in coal mines, the special case of access to only two opposite faces is emphasized. Classical matrix methods were used for small dimensional (2 by 2, 3 by 3, and 4 by 4) applications to determine the limitations and the requirements for a solution. The results for large (n by n) grids were then inferred and generalized from those of the smaller grids and matrices. Limited access tomography is found to be appropriate for in-seam hazard detection from seismic and microwave data, but it is shown that additional data must be added to obtain a direct solution.

Jan 1, 2010

A major hazard to workers in underground mines is fire and the resulting contaminated air. Fire reaches miners thousands of yards away with carbon monoxide gas and other toxic fumes. The same ventilation system that furnishes fresh air to miners can also be the vehicle to carry contaminated air to remote locations. To reduce these problems, the U.S. Department of the Interior's Bureau of Mines entered into Contract H0242016, "Mine Shaft Fire and Smoke Protection System," with FMC Corporation, Santa Clara, California, to evaluate mine shaft fire and smoke hazards and to develop and demonstrate a low-cost, reliable mine shaft fire and smoke protection system that would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines.

Jan 1, 2011

By Ε. P. YoUNGMAN

This paper presents one of a series of digests of foreign mining legis- lation and court docisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in vericis foreign countries. This interpretation of the laws - of Italy has been prepared, in part, from an aclysis made by John W. Frey, for merly associate mineral economist, U. S. Bureau of Mines. It incorporates addi- tional data and comments offered by Enrico Giobbe Della Pitta, a well-known Italian lawyer, in response to a questionnaire. These comments were forwarded by Harold H. Tittmann, American chargé d'affaires ad interim, at Rome, and trans- mitted to the Bureau of Mines through the courtesy of the Department of State.

Oct 1, 1930

By Sivalingam Jeevan, R. L. McConnell

Ground check monitors may be made in several configurations. Each type has unique characteristics and provides different safety attributes when applied to different mine situations. In this paper, the monitor types are discussed in relation to the mine situations. It is shown that the selection of the monitor type can have a significant effect on the safety of the resistance grounded power system. The options are discussed, and the conclusion is drawn that only one monitor configuration can provide maximum safety. Unfortunately no monitors of this configuration are presently available. In addition, when the monitor capabilities and ground wire configurations are considered as a system, it can be shown that certain configurations will lead to maximum safety. This work was supported by U.S. Bureau of Mines grant G0144138.

Jan 1, 1979

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This paper reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Research to reduce these accidents includes improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jan 1, 2000

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark- Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched. A new paradigm divides pillar failure into three categories:

By T. H. Davis

Twelve laboratories from the Western United States and Canada participated in radon progeny intercomparison measurements at the U.S. Bureau of Mines radon calibration facility in March 1987. The participants intercom pared grab-sampling and automated equipment methods at high and low concentrations of radon progeny and condensation nuclei (CN). The objective of this intercomparison was to determine if the measurement procedures and equipment of the North American facilities are equivalent. The sampling results showed good agreement among all participants. The standard deviation for the working level measurements was less than 3.5% for 1.70 working level (WL) and less than 8.8% for 0.21 WL. This relatively good agreement was achieved by using alpha standards calibrated by National Bureau of Standards (NBS) and by closely checking and monitoring airflows.

Jan 1, 1989

By Raymond B. Ladoo

Deposits of talc are known in many districts in Canada but at the present time active mining operations are reported only in Ontario . Here three companies are now operating, two of which, George H. Gillespie & Co. , Ltd. , and the Anglo- American Talc Co. , are at Madoc . The operations of the former company are probably the largest and best known in Canada . The writer , in his capacity as an engineer of the U. S. Bureau of Mines , was permitted by this company to make an inspection of its mine and mill in June, 1920 , and study the methods employed . This information was desired for comparison with methods employed in the United States . The following description is based on observation made during this visit , supplemented by data supplied by the company .

Sep 1, 1920

To help mine safety and health professionals manage and reduce hazardous noise exposure with a software tool that simplifies the record-keeping and analysis process. Background Hearing loss resulting from overexposure to noise continues to be a problem throughout the U.S. mining industry. Studies indicate that 70%?90% of all miners have a noise-induced hearing loss severe enough to be classified as a hearing disability by the time they reach retirement age. To address this problem, the National Institute for Occupational Safety and Health (NIOSH) developed the Determination of Sound Exposures (DOSES) software program. DOSES is designed specifically for use by mine management and safety personnel to simplify the record-keeping and analysis associated with time-motion studies, making it easier to identify and solve noise exposure problems.

Jul 1, 2009

By T. O. Llewellyn

The Bureau of Mines conducted batch-?scale tests on a sample of parphyry copper mill tailings as part of a study to determine the feasibility of rutile recovery from this source. The tailings that were tested contained 0.75 percent titanium dioxide (Ti02), with about two-thirds of the Ti02 values occurring as rutile. Mineralogical studies indicated that about one-half of the Ti02 content could be considered recoverable. Beneficiation studies of the tailings showed that best flotation results were obtained when sulfides and carbonates were removed by bulk flotation prior to rutile flotation. Rutile flotation was most effective when a petroleum sulfonate collector was used in an acid circuit. From this basic method of flotation, two alternative procedures were developed. The first procedure was to size and grind the tailings to minus 200 mesh; deslime the total pulp; and then float the sulfides, carbonates, and rutile. The second procedure was the same, except that it did not include sizing and grinding. Flotation of the sized and ground tailings yielded rutile concentrates containing 43.1 percent Ti02 and 75.7 percent of the recoverable Ti02. Rutile concentrates floated from the tailings that were deslimed but not ground contained only 34.7 percent Ti02 and 69.4 percent of the recoverable Ti02.

Jan 1, 1980