Search Documents

By Markus A. Reuter, Bernardete Castro, Antoinette van Schaik, Han Remmerswaal

This paper describes the inseparable relation between product design, liberation, and metallurgical recovery in the optimisation of the recycling of passenger vehicles. This is illustrated by the use of an optimisation model that uses among others a material combination matrix based on metallurgical process data, which depicts the consequences of the quality of intermediate recycling products on the metallurgical material recovery and final alloy metal quality. Various simulations will illustrate the effect of changes in product design and hence liberation on the recycling of end-of-life vehicles. Although this paper focuses on cars, the discussion is equally valid for any end-of-life product. Calibration of the model will be discussed with reference to experiments carried out in order to study the optimal recovery of aluminium applications used in passenger vehicles.

Jan 1, 2003

By X. L. Song

A large amount of tailings in concentrators bring a series of problems to the environment and society. It is significant to reclaim the huge tailings and reuse them in industries in order to utilize mineral resources adequately. Primarily Lead-Zinc tailings with a certain quality of clay and feldspar were used to produce ceramic tiles by sintering method under specific technical conditions. By testing the properties of the ceramic tiles, it was shown that the amount of Lead-Zinc tailing used in the tiles was 60%~70%, and the mechanics properties were good. The optimum proportion parameters were Lead-Zinc tailing 60%, clay 35%, feldspar 5%, and the maximum flexural strength of tiles was up to 38.2MPa when it was sintered at 1090? for 30min. Its flexural strength, water absorption and thermal shock resistance reached the State Standard of GB/T4100.4. The product is suitable to be used in pavements and paths of parks.

Jan 1, 2014

By M. Barsky, E. Barsky

It is generally accepted that the optimal flow velocity for gravity classification is the final particle settling velocity or, which is the same, the particle spin velocity. However, we have found differences between the settling velocities and the spin velocities of the very same particles. Here we present the results of experiments in a cascading gravitational classifier comprising eleven stages. The feed material was introduced at each stage successively, from the first to the eleventh. The optimal flow velocity was determined for each case. From these experiments it follows that the value of the optimal flow velocity depends to a greater extent on the point of introduction of the feed (i.e., on the design of the device) than it does on the interaction between the solid phase and the flow.

Jan 1, 2003

By M. Rudolph, E. Schach, M. Buchmann, T. Leißner, N. Krupko, U. Peuker, M. Kern

"In mineral processing, density and magnetic susceptibility are two very fundamental properties. For the beneficiation of valuables to produce a saleable concentrate a detailed understanding of these properties is essential. Especially when it comes to the processing of cassiterite, which is the main mineral for tin production, they become highly prominent. Due to the chemically inert character of cassiterite towards most industrial applied leaching agents, density and magnetic separation processes are mainly applied for its beneficiation. To guarantee an optimized utilization of the different operations not only cassiterite but also the different gangue minerals have to be considered. In this study, a skarn ore is characterized by density and magnetic susceptibility. Therefore, the material was first split into different density classes by heavy liquid separation. The obtained classes were further separated by their susceptibility to finally obtain a density-susceptibility matrix. For this purpose, an isodynamic separator was used. A more detailed characterization of the materials is done via gas pycnometer, magnetic susceptibility balance and vibrating sample magnetometer to estimate the characteristics of density and susceptibility for the various classes. Further, the determination of the chemical assay and the mineral intergrowth by mineral liberation analysis is used to generate a three dimensional database for detailed characterization of the present ore. The objective of this study is to estimate potential material streams for a modular processing plant via characterization of the material for the entire deposit by the two afore mentioned characteristic properties. The established multidimensional data matrix, enables predictions for the separation properties of the material and contributes to the characterization of the deposit within the context of geometallurgy."

Jan 1, 2018

By Christopher Greet, Alfred Van den Bosch

"A range of media alloys with different chromium content has been developed for different milling applications. When selecting the grinding media alloy for a specific application, consideration must be given to the mineralogy of the ore as well as the water chemistry and mill operating conditions. The paper describes the influence of the microstructure of the alloy on the wear resistance and the influence of the chrome content on the pulp chemistry and downstream processing. It also provides information about the in-house tools which Magotteaux have developed to predict the media wear rate with different chromium content alloys and predict their flotation efficiencies that can be expected when the right alloy is selected for a particular application."

Jan 1, 2014

By Alex Heath, Andrew Barycki, Baladron. Javier

"Efficient flocculation is important to thickener performance, affecting the overflow clarity, solids settling flux, underflow density and operability. Many factors affect flocculation; from the material/flocculant type, dilution of the feed and flocculant solution, mixing, to the shear rate and shear history. The flocculant addition point (or points) can be used as a tuning method to alter the effective flocculation time in a feedwell, with addition further up the feed pipe increasing the residence time but making the aggregates more prone to breakup if they experience high shear later in the process. Conversely, adding the flocculant later, eg under the feedwell shelf decreases the mixing time but allows some free (unadsorbed) flocculant to be available at the feedwell exit. An extensive trial has been performed on an operating thickener comparing seven individual different flocculant dosing positions through a Vane feedwell, and some combinations of two dosing points simultaneously. Measurements of the velocity, solids concentration and aggregate size were made throughout the feedwell at the different positions, with the dosing points significantly changing the aggregate size and clarity, and also affecting the solids concentration at some positions. The results are accessed in terms of flocculation kinetics and used as CFD validation data."

Jan 1, 2014

By N. Syna

The selection and preparation of activated carbon suitable for specific application can often involve exhaustive adsorbent preparation and testing. This work examined an emerging technique based on modelling the correlation of observed adsorption capacity to the carbon characteristics as a means of decoupling the roles of carbon textural and surface chemical properties. The insights to these specific roles are then used in tailor-making adsorbents and in establishing the optimal carbon properties for specific application. In this study, a series of activated carbons prepared from bagasse by physical and chemical techniques and commercially available carbons were used in developing the models. These carbons were tested for the adsorption of thiourea-gold (I) chloride complexes. Thiourea is an important alternative gold lixiviant with the potential to address current ecological and safety concerns in the extraction of gold. A four-component model, which correlated the adsorption gold capacity to carbon textural and surface chemical properties, was proposed. The model fit was assessed using multi-linear regression and a partial F-test. This was followed by goodness of fit test achieved through r2, adjusted?r2 and mean square error (MSE) values. The results suggest the adsorption of the gold-thiourea complex is strongly influenced by the internal surface area and pH of the carbon. Tailor-made activated carbon from bagasse showed adsorption gold capacities of up to 198 mgAu/g adsorbent, demonstrating the potential of bagasse as a precursor for gold adsorbents and of this empirical modelling approach in developing adsorbents for metal recovery.

Jan 1, 2014

By T. Moloane, C. Bergman, Heloise Thiele

"A pilot test campaign was undertaken to evaluate dense medium cyclone separation efficiencies on samples of iron ore fines (-1mm +300µm). Evaluations were done using both gas and water atomised FeSi types across a range of operating conditions in the presence of slimes build-up. A Mineral Liberation Analyser (MLA) was used to measure size, density, shape and liberation data of DMS feed and products. The results of the test work were used to obtain parameters for modelling of the partition size/density response. The findings indicated that accurate density characterisation of the feed ore is essential in understanding product quality and recovery, particularly due to the effect of porosity and micro-inclusions. A significant off-set between cyclone underflow density and separation cut-point (D50) was found indicating that relatively low feed media densities (about 3.4g/cm3) are required to achieve high density cutpoints of over 4.0g/cm3. In agreement with CFD modelling, the separation quality is dominated by viscous effects, hence FeSi type and slimes content will need to be carefully controlled to ensure efficient separation.INTRODUCTION In the South African context, future resources of hematite are expected to be both of lower head grade and will contain a higher content of banded iron formation (BIF) (1). These ores may require finer crushing in order to liberate the high-grade fractions and will thus increase the amount of -1mm material to be processed. In order to efficiently upgrade these materials, it becomes necessary to re-examine both traditional and novel processes to treat material finer than 1mm in size. These include spiral and up-current classifiers, wet high intensity magnetic separation processes, Reflux classification and potentially includes dense medium separation (DMS). This study presents a technical evaluation of fines DMS using a mineralogically-based particle tracking analysis method (PTA) to calculate efficiencies of separation."

Jan 1, 2018

By U. M. J. Boin, E. V. Verhoef

Pyrometallurgical reactors constitute a key processing component in the total primary and industrial/recycling resource cycle, being involved both in primary smelting, converting and extraction, as well as the reprocessing of scrap, from aluminium cans to end-of-life automobiles. Therefore the pyrometallurgical reactor?s role in achieving sustainability is the central theme discussed in this paper since optimising their operation minimises waste, residue and offgas (NOx, dioxin, CO2) and maximises product quality and therefore efficiency. To effectively control the overall resource cycle, one needs to take a systems modelling approach of the whole cycle, seeking to also understand the dynamic process behaviour of the individual components of the cycle, and then especially the part that contributes most to the chemical conversion, namely the pyrometallurgical reactor. This paper highlights the role of pyrometallurgical thermodynamics in the whole resource cycle and specifically places equilibrium thermochemistry in the context of process dynamics where large, variable inventories are recycled or maintained within the system. This paper will therefore review the semi-empirical dynamic modelling tools, which are used to model complex systems with the specific goal of developing dynamic predictive models, which also include slag-alloy chemistry, towards controlling the recycling in a feed forward manner. To illustrate the primary production of metals, high carbon ferrochrome and Ni-Cu-matte smelting will be presented as a brief case study. Also fundamental studies in blast furnace and waste incineration kilns will be given. It also will show how the distributed nature of the chemistry of melts in the case of primary extraction, and industrial (recycling) materials such as recycled end-of-life vehicles, have a significant impact on the process outcomes and model predictions. It is therefore argued that the fundamental thermodynamics and kinetics in metallurgical reactors play a final crucial role in modelling the closed material cycle, but only when it is used in conjunction with process systems theory based on reconciled data for parameter estimation and model calibration. System models for aluminium and car recycling will be given as well as a dynamical system model that describes the interconnected material flows for Ag, Au, Bi, Cu, Fe, Ni, Pb, PGM, Sn and Zn for a study on lead-free solder.

Jan 1, 2003

By Q. Zhang

The flotation behavior of jamesonite was investigated with ethyl xanthate as a collector. It has been shown that jamesonite has good floatability from pH 2 to pH 12, and relatively poor floata-bility at pH>12. The flotation of jamesonite was also dependent on pulp potential at certain pH val-ues. The potential-pH range for jamesonite flotation was established. The FTIR spectroscopy analy-sis and XPS measurement showed that the major adsorption product of ethyl xanthate on jamesonite was lead ethyl xanthate and antimony ethyl xanthate. The intensity of the FTIR signals of metal ethyl xanthate adsorbed on jamesonite and the flotation response of jamesonite were correlated with pulp potentials.

Jan 1, 2014

By T. Bhambhani, O. Yavuzkan, D. R. Nagaraj

"The recovery of oxide Cu minerals by flotation is a longstanding challenge in the minerals industry, especially for high acid-consuming ores which would not be economical for direct acid leaching. Sulfidization (often using controlled potential sulfidization or CPS) using NaSH (or Na2S) followed by flotation using traditional sulfide collectors is the widely used technique. CPS has certain limitations: a) inability to recover certain oxide Cu minerals because they are refractory to sulfidization, b) high consumption of NaSH (or Na2S), and c) potential health and safety hazards associated with NaSH (and Na2S). Flotation of oxide copper minerals using alkyl hydroxamate (AHX) collector has been studied extensively. Investigations using single minerals and laboratory ore flotation have been conducted in the past to demonstrate the efficacy of alkyl hydroxamates. The technology has been used intermittently in plants. One of the main challenges in plant use has been quantifying the true potential for alkyl hydroxamates for recovery of various oxide Cu species in complex and variable ore systems and identifying the most suitable conditions for optimal use. Quantitative mineralogical analysis using QEMSCAN was used in this study to characterize flotation products lab flotation samples. Analysis of concentrates and tails from hydroxamate flotation and CPS flotation stages demonstrated that certain oxide Cu minerals respond exclusively to alkyl hydroxamates and not to CPS. The hierarchy of interaction of AHX with the various oxide Cu minerals could be inferred from these studies. Finally, these studies also allowed quantification of a group of minerals species, which (erroneously) report as part of the Acid-Soluble Cu [ASCu] but cannot be recovered by flotation, thereby facilitating an estimation of the true recovery potential for alkyl hydroxamate.INTRODUCTIONCopper that is economically recoverable occurs in three major types of ores, which are defined by the modal mineralogy of Cu. For sulfide ores, Cu occurs as sulfide minerals and is satisfactorily recovered by flotation using sulfide collectors. Non-sulfide ores, which contain Cu in the form of oxides, phosphates, carbonates and silicates, described in the industry as “oxide” ores (or ores containing “acid-soluble” Cu or ASCu), are currently treated using hydrometallurgy, which involves leaching with dilute sulfuric acid followed by solvent extraction and electrowinning, unless the ores contain acid consuming gangue minerals such as dolomite. For mixed sulfide-oxide ores (i.e. containing both sulfide and oxide Cu minerals) that do not contain acid consuming gangue minerals, Cu values are easily recovered by flotation of sulfide Cu minerals followed by leaching of oxides (only when a leach plant is available). However, when the ore contains acid consuming gangue minerals flotation is required to recover both sulfide and oxide Cu minerals."

Jan 1, 2018

By V. E. Vigdergauz

Possibilities of the analysis of potential energy of bubble-particle interaction on the basis of extended DLVO theory are discussed. Interaction energies of mineral silica, coal and pyrite particles with contact angles from 20 to 100 degrees and air bubbles in neutral and alkaline solutions are analyzed. It is shown that for hydrophilic silica, the formation of particle-bubble complexes (either in the area of primary or secondary potential minima) is impossible due to the high potential barriers (from 6000 to 140000 kT)and low values of the attraction force. There is shown that for coal and pyrite particles the energy of interaction vs. particle-bubble distance strongly depends on pH value. Improvement of floatability of minerals by the hydrophobization of their surface by collectors leads to the eliminating of potential barriers and the formation of the stable complexes of minerals and air bubbles in the area of primary potential minimum. In addition, due to hydrophobization of coal and pyrite changing pH has practically no influence on the energy of interaction. There are discussed results of the numerical calculations of normalized interaction forces in particle-bubble systems on the nanometer distances for pyrite, sphalerite, and chalcopyrite at contact angles up to 85° in comparison with the experimental data. The values of adhesion force for hydrophobized particles of coal and pyrite to air bubbles are about 10-5 N, that indicates stability of the formed flotation complexes. Examples of using the long-range and high-energy effect of hydrophobic interactions for improving minerals floatability are discussed. There are illustrated minerals wettability changes induced by the adsorption of thiol collector and hydrophobic polymer. Possibilities of flocculation and flotation of mineral slimes due the polymer-collector hydrophobic interactions are shown. Keywords: bubble-particle interaction, contact angle, extended DLVO theory, floatability

Sep 1, 2012

By Shenxu Bao, Ying Bian, Xiang Liu, Liuyi Ren, Yimin Zhang, Chun Liu

Efficient enrichment of high-carbon low-grade mica stone coal containing vanadium is a key problem in the mineral processing field, and the mature beneficiation process is yet to be developed and applied. In this paper, a special mineral mica type of stone coal containing vanadium from Tongshan, Hubei Province, China was selected as the research object. Chemical analysis results show that this mineral contains V2O5 0.71%, SiO2 49.28%, C 13.44%, and CaO 6.26%. Scanning electron microscope (SEM) shows that vanadium generally exists in all kinds of mica minerals in 20 µm to 50 µm fractions. Mica stone coal containing vanadium must be ground to a particular fineness (approximately 45 µm). To reduce acid consumption during vanadium extraction from stone coal through acid leaching, a pretreatment process was proposed to enrich micas by using shaking table and flotation methods. A new combined technology process was implemented, resulting in a 0.96% improvement in the vanadium grade of raw materials in the succeeding process. Vanadium losses were controlled to 4.57% through the pre-concentration process, which reduced the burden of the subsequent procedure. The content of high acid consuming minerals was also diminished, such that approximately 6612 CNY was saved from producing 1 t V2O5. Therefore, stone coal containing vanadium should be pre-concentrated by using an appropriate combined process to reduce costs.

Jan 1, 2014

By C. A. Perez

Estimation of rock composition in mineral plants is important to determine rock size and grindability which in turn may improve control of the grinding process. Variations in ore grindability and size distribution directly affects mills power consumption and throughput. Therefore, it is desirable to develop new tools to estimate rock lithological composition. In this paper, a new method for lithological classification based on machine vision is proposed. The method is based on a single video camera and employs information about texture using several different spatial scales. Texture information is extracted from rock images using Gabor filters that can be adjusted at different spatial scales and orientations. After feature extraction, rock images are classified using support-vector machine (SVM). The method was tested on a database containing sub-images of 64x43 pixels of five ore types as follows: massive sulphide (MS), disseminated sulphide (DS), net textured (NT), gabbro (G), and peridotite (P). These ore types were assigned to three grindability classes: soft (MS), medium (DS and NT) and hard (G and P). The database was divided in 2 subsets for training, cross validation, and for test. Classification accuracy is compared with previously published results on a dataset with three different classes of rocks according to their hardness. Results show that our proposed method reached significant improvements (between 13%-20%) in classification accuracy relative to previously published results. Keywords: rock classification, lithological classification, grindability estimation, Gabor feature extraction, texture features

Sep 1, 2012

By Gülay Bulut, Ferihan Göktepe

Pyrite is the most abundant and widespread sulphide mineral and its flotation has been investigated by many researchers. It is well known that, pyrite is floatable under acidic conditions and recovery drops with increase in alkalinity due to changes in solubility of iron hydroxides on the pyrite surface. Most of the works also revealed out that pyrite displays variable behaviour in flotation circuits. This behaviour mainly related with origin and mineralogical composition of ore, liberation size, electrochemical behavior of minerals constituting ore, the trace and minor element content of the mineral, texture, application variables belonging to flotation circuits. In this study, copper activation effect was examined on different origin of pyrites. The experiments were performed with five high grade samples of pyrite from the different mining districts of Turkey. The pyrite samples were different from each other with respect to either their physical or chemical properties; they were different physical appearances and contained different associated minerals. In the micro-flotation tests, 1x10-4 mole/L copper sulphate and 1x10-4 potassium ethyl xanthate were used as flotation reagents. First of all pyrite samples were floated using only xanthate at different pH. Results showed that best floatation results obtained at acidic pH range for all pyrite samples. When copper ions were used to activate, all pyrite samples floated at neutral and basic pH values, too but depending on the samples, recovery and pH ranges were slightly changed.

Jan 1, 2014

By B. Orberger, J. M. Milazzo, S. B. Blancher, J. Lützenkirchen, J. L. Dubos

"Industrial dusts are commonly agglomerated using empirical recipes with binders such as bentonite, while Sludges are agglomerated into mixes. Those materials contaminate the products, are expensive and generate significant amounts of slag. Achieving cold dust agglomeration with little or no binder requires understanding the controlling parameters in order to predict and optimize the process behavior. This in turn necessitates comprehensive dust characterization to base predictions on measurable characteristics. In the present work we collected 13 Mn-rich dusts over all the process chain: feed fines, smelting, and refining dusts, as well as ferromanganese alloy dust. This is the first systematic study of dusts along the Mn-processing chain for chemical, physical and mineralogical parameters. X-Ray Diffraction, Qemscan® and laser granulometry analyses show that the mineralogy, Particle Size Distribution (PSD) and morphology evolves from complex heterogenous to simple, homogenous along the process chain: The mineralogy of the primary ore dusts shows various hydroxides, oxides, carbonates, tectosilicates and phyllosilicates. The furnace dusts contain oxides, tectosilicates and carbonates with volatiles, while the refining dusts present only oxides and metal. Finally, the Metal dust is nearly pure metal. Particle morphologies and PSD vary from jagged, irregular particles with broad PSD (>1 mm to <0.3 µm) to smooth and spherical with narrow PSD (100 µm to <0.3 µm). The Metal dust is an exception with angular particles. The Cationic Exchange Capacities (CECs) of all samples range from 0 to 22 meq/100g. Specific surface areas (SSAs) range from <0.1 to 27m²/g, and seem to decrease with from ore feed to Metal dust. This may be due to the disappearance of hydrated and/or sheet-bearing minerals, since a smaller grain size usually implies an increased SSA. The zeta potential varies strongly over the range of the samples tested. However, beside the Gabon ore which has an Isoelectric Point (IEP) ~ 4.1, the other IEP ranges between 2 and 2.5."

Jan 1, 2018

By V. A. Luganov

Methods of treatment of pyrite concentrates differ, depending on the content of pyrite and non-ferrous metals: oxidation roasting, sulphatization roasting, smelting, direct hydrometallurgical treatment and so on. Existing technologies do not provide for high recovery of metals, expenses associated with existing technologies are high, and environmental issues, associated with the existing technologies need serious attention. We have developed universal technology of the activating-dissociating autogenous roasting of pyrite concentrates using air based, or air, enriched with oxygen, blow. The basic process is taking place in accordance with the following reaction: (1-x)FeS2 + (1-2x)O2 = Fe1-xS + (1-2x)SO2 +Q The products of this reaction are pyrrhotinized cinder and roasting gases, rich in SO2 (up to 18 % in case of air blow) and poor in SO3, that contain up to 1 % of elemental sulphur. Cinder contains different forms of pyrrhotite. These forms of pyrrhotite differ by its content (from Fe0.843S to Fe0.945S), thermodynamic, magnetic (from 4.10-1 to 3.6 SI units), flotation properties (with pyrite dissociation the ?-potential of the product is moving towards more electrically positive charge, from 0.95 for pyrite to 0.2 for dissociation products) and other properties that depend on the conditions of roasting. The combination of pyrrhotizing roasting with different methods of cinder treatment allows to increase the level of sulphatization of non-ferrous metals during the roasting; reduce the amount of blow used during the processing; reduce dust losses to the gas phase; reduce the capacity of gas cleaning system and increase resistance to corrosion of the gas-treatment system, used for the production of sulfuric acid from pyrites. This combination of treatments also allows to use magnetic separation and flotation for separation of ferrous and non-ferrous metal compounds during cinder treatment; perform de-arsenation of arsenic containing concentrates and by-products. Pyrrhotinized cinder may be treated by oxidizing and non-oxidizing hydrometallurgical methods. Keywords: Pyrite, polymetallic ores, sulphidization roasting, pyrrhotite, magnetic separation, arsenic sulphide

Sep 1, 2012

By D. Hatfield, G. de Jager

"The rapid developments in computer vision and computational resources are creating new possibilities for the use of machine vision systems for industrial control. A number of commercial image analysis systems exist, and research into improved measurements of froth performance is ongoing. An integral part of the implementation of these systems is the validation of the relationship between image analysis measurements and flotation cell performance. This paper discusses the factors affecting concentrate flow and presents the results obtained from one such system with respect to its ability to estimate the flow of concentrate from a flotation cell.The relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell was investigated on two industrial operations, both processing PGM (Platinum Group Metal) bearing ores. Results are presented that show a relationship between froth flow speed and concentrate yield."

Jan 1, 2003

By J. T. Liu

Packing in a flotation column is one way to increase separation efficiency and effective descending flotation-column height. In this paper, the difference between filling packing and sieve packing is described, and the flaws of filling packing in flotation columns in industrial application are pointed out. A change of flotation process and its effect on flotation results are reported. Based on sieve-plate filling, a high-efficiency mixed packing mode consisting of screen-plate packing and honeycomb-tube packing has been proposed, with the packing mode optimized in the cyclonic static microbubble flotation column in the separation zone. In the mixed packing mode, the honeycomb tubes are used to reduce the vortex effect at the base of the column and weaken the radial dispersion of jetting bubbles, and the sieve plates are used to comminute bubbles in the separation zone, to lengthen the bubble migration path, and to stabilize the foam layer. The superiority of honeycomb-tube packing is analyzed using bubble-particle collision theory, and the dynamic equations of collision probability are derived. The role of mixed packing in guaranteeing mineral recovery is analyzed by the axial dispersion method, and a dimensionless axial dispersion model is derived. When a high-turbulence flow is maintained, a static separation environment is formed in which secondary mineral processing is rendered more effective. In this way, a nonlinear separation environment is formed in the flotation column. Finally, mixed packing was applied in an industrial test. A large vortex developed at the base of the column. It was observed that the bubbles in the radial flow were homogeneously dispersed, the residence time of the pulp was prolonged, and the froth layer became thick and stable. Based on the test data, it was found that the sieve packing has the potential to yield a product of approximately 25.83% copper concentration with 91.78% recovery from a feed concentration of approximately 0.727%. If mixed packing were used, the product concentration could be further increased to 27.60% from a feed of approximately 0.739% concentration with 93.38% recovery.

Jan 1, 2014

By D. Saramak

"High-pressure grinding technology is considered as one of the most efficient techniques of ore comminution, especially in terms of energy consumption. HPGR devices has been utilized in many mining-related industrial sectors, including iron and non-ferrous metal ores processing (copper, platinum, gold), as well as cement and limestone flour production. Even though the technology well known (introduced into mineral processing circuits in 80’s), there are still examples of ineffective operation of HPGR devices. This is a result of improper application of HPGR into individual crushing circuit. The purpose of the paper was to analyze selected effects achieved in HPGR on the course and effectiveness of beneficiation operations. Investigations were carried out for copper ore, and investigative programme was run for different values of HPGR pressing force, as well as changeable ore characteristics (content of fine size fractions, material moisture). All crushing products were then treated in flotation process, in order to determine useful mineral recovery. Results of investigations show that HPGR operating pressure influences the metal recovery in proportional way, however too extensive pressure values have relatively lower impact on increasing of the metal recovery. Particle size distribution of HPGR feed and its moisture have lower influence on recovery level than HPGR pressure, but too extensive moisture content influences the higher energy consumption of the roller press, together with less effective comminution. The second aspect raised in the paper was a possibility to control and optimize the HPGR-based circuit. There were presented the proposed approach to adjustment of HPGR operating parameters that enables the higher metal recovery.INTRODUCTION The high-pressure grinding technology, invented and developed by Professor Schoenert in 70’s (Schoenert, 1979), is currently regarded as one of the most efficient methods of hard ore comminution. Since then the technology was introduced into raw materials treatment circuits in many mining and mining-related industrial sectors, including iron and non-ferrous metal ores processing (copper, platinum, gold), as well as cement and limestone flour production. Considerable number of works concerning modeling and optimization of HPGR operation were also presented (Daniel & Morell, 2004, Tavares, 2005, Saramak, 2012, Saramak & Kleiv, 2013). Nowadays high-pressure grinding rolls devices are considered as well know technology with over 500 sold machines, according to various sources."

Jan 1, 2018