Search Documents

By Beim Jorge, Piscsalko George

"Verifying the quality of cast-in-place foundation applications, particularly those cast under slurry, is of course important, due to its great dependency on the methodology employed and on the practices of the site personnel. Due to the techniques used to install these elements, it is usually not possible to inspect the hole prior to grout or concrete placement, but there are several Non Destructive Test (NDT) methods available to assess the integrity of the completed foundation elements. This paper will compare several NDT methods with the Thermal Integrity Profiling (TIP) method for verifying the integrity in Continuous Flight Auger (CFA) piles and Bored Piles. The Thermal Integrity Profiling method will be described and some examples will be presented where TIP testing was used to confirm the structural integrity of CFA piles and Bored Piles.IntroductionThere are several Non Destructive Test (NDT) methods available for integrity testing of foundation elements. Each of those methods has advantages and disadvantages (White et al, 2008). Some methods test the integrity based on the reflections of a stress-wave generated by low or high-strain impact, while others require tubes to be installed prior to concrete pouring, and test the integrity between those tubes, or within a small proximity of them. The former methods (especially the low-strain) are faster and more cost-effective, but are not able to detect the quadrant where the damage is located. The latter methods are able to determine the quadrant, but do not test the region outside of the reinforcing cage, that is, they are not able to determine the concrete cover. The Thermal Integrity Profiling (TIP) NDT method overcomes the limitations of these other NDT methods.Overview of Shaft Integrity MethodsUntil now, the most widely used methods to test the integrity of Bored and CFA piles were the low-strain pile integrity testing and the cross-hole ultra-sonic testing. The low-strain method for integrity testing (PIT) involves attaching an accelerometer usually to the pile top (using a putty or wax) and striking the pile surface with a handheld hammer, which causes a compressive wave to enter the pile. This wave is totally reflected when it reaches the end of the pile or a major defect, and is partially reflected when it encounters any change in crosssection, or a change in the resistance or density of the pile material. These reflections arrive at the top at a time determined by the distance and wave speed, and causes a noticeable change in the signal detected by the accelerometer. The acceleration signal is normally converted to velocity by simple integration, and sometimes the force applied by the hammer is also measured. The velocity (and force) signals can be processed by the pulse-echo method (in the time domain) or by the transient response method (in the frequency domain)."

Jan 1, 2015

By John P. Turner, Benjamin J. Turner

"This report describes a research project for evaluating the applicability of the widely accepted 80 percent criterion for elongation of ground anchors to anchors with unbonded lengths exceeding 100 feet. This issue is driven by several recent projects involving ground anchors for landslide stabilization in which a significant percentage of the anchors did not meet the criterion that requires measured elongation during proof load testing of at least 80 percent of the theoretical elastic elongation. The projects involved anchor unbonded lengths in the range of 85 to 220 feet, which is outside the range traditionally used in practice, although anchors of this length are being used more frequently for landslide stabilization. The principal objective of this research is to address whether the widely accepted criterion of 80 percent elongation is applicable for such applications, and whether other factors affect the ability of anchors to meet the criterion.Analytical methods for predicting transfer of load along the length of steel strand due to friction loss are used routinely in the prestressed concrete industry. These analytical expressions provide a rational framework for quantifying changes in load due to friction along the length of a ground anchor in terms of a ‘wobble coefficient’ (K) as defined in Aalami (2004). Values of the wobble coefficient for ground anchors can only be determined by back-calculating from load tests, i.e., fit the value of K to the appropriate analytical expression based on the known test load and measured percent elongation. The analytical basis is first developed and shown to provide a tool for evaluating results of anchor load tests to determine the magnitude of expected elongation as a function of unbonded length. Next, a database of anchor load tests is used to back-calculate values of K for anchors with unbonded lengths in the range typically used in geotechnical applications (< 100 feet). These values of K are then used to calculate expected friction loss for anchors with high unbonded lengths (100 to 250 feet) to evaluate whether the 80 percent criterion is reasonable."

Jan 1, 2017

By Takeru Fukaya, Tsutomu Namikawa

"The bending tensile stress occurs in the ground improvements when external forces are applied to the column and wall shaped ground improvements. Therefore, in the design of the column and wall shaped ground improvements, the tensile properties of the cement-treated soils become a predominant factor when the external forces induce bending moments. Then the tensile properties are required to design the ground improvements rationally.Three points bending tests are conducted to investigate the bending tensile properties of cement-treated soils in this study. Cement-treated soils mixed in a laboratory are used in the bending tests. The test specimens are prepared with the several mixing properties to study the relationship between the tensile properties and unconfined compressive strength qu. Bending tensile strength Tfb and fracture energy Gf of the cement-treated soils are evaluated from the load-deflection curves obtained from the bending tests. The experimental results indicate that Tfb and Gf are approximately proportional to qu.INTRODUCTIONThe ground improvement by deep mixing has been widely used for structure foundations, retaining walls and liquefaction mitigations. Recently column and wall shaped ground improvements by deep mixing method have been applied for economical reason. When external forces are applied to the column and wall shaped ground improvements, the bending tensile stress occurs in the ground improvements. Therefore, in the design of the column and wall shaped ground improvements, the tensile properties of the cement-treated soils become a predominant factor when the external forces induce bending moments. Then the tensile properties are required to design the ground improvements appropriately.Namikawa et al. (2007) conducted the finite element analysis to investigate the dynamic behavior of the lattice-shaped improved ground for liquefaction mitigation. In the analysis, an improved ground consisting of several grids in a line was chosen to study the basic behavior of the lattice-shaped improved ground. Fig. 1 shows a example of calculated tensile failure zones in the improved soil during the earthquake. Half of one section of the improved soil consisting of two grids in a line for the 8 m × 8 m grid was modeled in the case. In Fig. 1, the failure occurs at the bottom and upper corners of the improved soil grid. The analysis result indicates that the constitutive model which can appropriately evaluate tensile failure behavior of cement-treated soils is required to evaluate the performance of the lattice-shaped improved ground for liquefaction mitigation. In the analysis, the elasto-plastic model developed by Namikawa and Mihira (2007) was adopted for the cement-treated soil behavior. The elasto-plastic model can suitably describe the tensile failure behavior of cement-treated soils. In the elasto-plastic model, tensile fracture energy is adopted to determine a tensile softening relationship because it is difficult to directly measure the stress-strain relationship after the peak stress state in direct tension tests. However there is little experimental study on the tensile fracture energy of cement-treated soils."

Jan 1, 2015

By G. L. Sivakumar Babu, P. Chaithra

"Raft foundations which are used against differential settlements and for carrying heavy loads can still be subjected to excessive settlements even if it is safe against bearing capacity consideration. Providing additional piles under the raft can reduce such settlements to acceptable values. In addition to settlements, the piles also relieve the raft a part of the total load and thus the bearing capacity of the Combined piled raft foundation (CPRF) is improved. Parametric study of response of piled raft foundation has been conducted and the results have been presented. The study is conducted using finite element based software, PLAXIS 2D. The main objective of the paper is to evaluate the parameters that affect the performance of piled raft for an economical and effective design. It has been shown that piled rafts are an economical solution in foundation design compared to raft foundation, for the soil conditions considered in the paper.1. INTRODUCTIONThe aim during the design and construction process of high-rise building foundations in urban areas is to ensure the lifelong safety and serviceability of the new and existing buildings in the neighborhood. In order to realize this aim in a cost-optimized manner, the combined pile raft foundation (CPRF) was developed (Katzenbach et al., 2005). For the foundation of high rise buildings with good subsoil, the simplest structure considered is a raft. But when the subsoil near the ground surface has low load-bearing capacity, high-rise structures are often rested on piled foundations.A piled raft and pile group serves similar purposes, but there are essential differences between them. A pile group is a set of piles that have a pile cap. The piles would be designed to share the pile load at ultimate state. The pile cap would be designed to link the piles together but the contribution of the pile cap to bearing capacity will not be included in the design. On the other hand, a piled raft is a foundation, wherein piles are provided along with the raft so that the total load acting is shared partly by the raft and partly by piles, rather than being dominated by the piles (as in a pile group). Piled raft foundations utilize pile support for control of settlements with piles providing most of the stiffness at serviceability loads, and the raft element providing additional capacity at ultimate loading (Poulos, et al., 2011). Therefore, piles are included in a foundation for two main design purposes: to provide adequate bearing capacity and to bring down the settlements to an acceptable level."

Jan 1, 2015

By Serhan Guner, Sundar Chiluwal

Although significant research has been conducted on helical piles, there is a lack of research and official design provisions on the helical pile-to-pile cap connections. These connections may govern the global response of pile cap systems—especially in tall and light structures where uplift forces dominate the response. To improve future industry practice, the objective of this study is to understand the influence of pile-to-pile cap connections on the global behavior of concrete pile caps and develop recommendations for their efficient design. For this purpose, 108 high- fidelity nonlinear finite element simulations are conducted to quantify the influences of bracket type, embedment depths, longitudinal reinforcement percentages, shear span-to-depth ratios, and loading conditions on the load, deformation, cracking, and failure behavior of concrete pile caps. The results indicate that the design configurations involving single bracket type may result in premature concrete cracking around the anchorage zones with a 25% reduction in the uplift load capacity. The investigations also confirm that high reinforcement percentages and low shear span-to-depth ratios result in higher load resistance in all bracket types, and that the load capacities of the double and studded bracket types are similar. For applications requiring the use of lower embedment depths, it is recommended that either double or studded bracket types be used. The research findings have applicability to both helical and micro piles given that both include similar connection types. INTRODUCTION Tall and light structures may experience significant uplift forces at their foundations due to large overturning moments from wind or other lateral loads. Helical piles (e.g., Fig. 1a) can provide a cost- effective, practical, and resilient solution for resisting significant uplift forces. In order to realize the full potential of helical piles, it is imperative that the helical pile-to-pile cap connections (see Figs. 1b, c and d for examples) are properly designed to resist the applied forces. However, there is a lack of research and associated knowledge on the influence of pile-to-pile cap connection detailing on the global response of pile caps.

Jan 1, 2019

By Daiki Takano, Naoki Takahashi, Hidenori Takahashi, Ikuo Towhata, Yoshiyuki Morikawa

"The method in this study, in which cement-treated piles are installed into the ground to decrease the amount of liquefied lateral flow, has been studied. The authors are also investigating the most effective arrangement of piles to optimize cost-effectiveness. In their investigation, they propose shifting the position of the piles to prevent lateral flow in various directions. The present study conducted centrifuge model tests to clarify the improvement effect of piles against the lateral flow of liquefied soil and the effect of the pile arrangement. Then, numerical fluid analyses were conducted to consider the improvement mechanism. As a result, the model tests and numerical analyses showed that the pile improvement dramatically reduced the lateral displacement and that the average total flow velocity decreased in the irregular case.INTRODUCTIONLiquefied ground subjected to seismic motion loses its stiffness and strength, and lateral flow often occurs in sloping areas and backfill areas behind collapsed quay walls. In the Hyogoken–Nanbu Earthquake in 1995, the reclaimed island that was surrounded by collapsed quay walls expanded toward the sea and the amount of displacement reached a few metres (Hamada et al., 1996). Two countermeasures can be considered to guard against lateral flow: preventing liquefaction and reducing lateral displacement. The former method is ideal; however it is costly and time-consuming. Based on these considerations, the authors (Takahashi et al., 2013; Morikawa et al., 2014) are currently studying a method in which cement-treated piles are installed into the ground (see Fig. 1) to decrease the amount of liquefied lateral flow. The countermeasure cost using this method is relatively low because of the low replacement ratio. The authors are also investigating the most effective arrangement of piles to optimize cost-effectiveness. It has been proposed that the position of the piles should be shifted so that lateral flow can be prevented in various directions, as described in Fig. 2."

Jan 1, 2015

By Theodore W. Vogelpohl

Augered cast-in-place piles have proven to be effective, adaptable and economical for projects throughout the Ohio River Valley. Specifically, they have been used extensively for high-rise structures, sports stadia and large commercial developments along the Cincinnati, Ohio and Northern Kentucky Riverfront. They have been designed and utilized as relatively short toe resistance piles in bedrock, and intermediate to long toe and shaft resistance piles in granular outwash deposits above the bedrock. They have been designed for large axial compression loads as well as moderate axial tension loads and lateral loads. This paper presents a few load test results that demonstrate the range of capabilities of augered cast-in-place piles in the variable subsurface profile along the Cincinnati, Ohio/Northern Kentucky Riverfront.

Jan 1, 2005

By K. E. Darnell

Drilled pier foundations have long been a favored foundation type for heavily loaded structures. Drilled piers derive their load-bearing capacity from end-bearing, and/or sidewall friction. This type of foundation is used in many geologic settings, including those areas underlain by hard carbonate rock, such as limestones and dolomites. When properly designed and constructed, drilled piers provide high load-carrying capacity in both compression and uplift. However, carbonate rock is often subject to intense differential weathering resulting in the formation of an irregular bedrock surface, sinkholes and caves; consequently, the investigation for, and the design of, drilled pier foundations is often complex. Further, the construction may be difficult and costly. This paper discusses geotechnical investigative procedures which can be employed to develop foundation design criteria and reduce the frequency of changed conditions. Finally, state-of-the-art construction practices and quality control techniques are discussed.

Jan 1, 2010

By Barry C. Roth

Driving of large piles in water can impact marine wildlife. Bubble curtains can mitigate these adverse effects. The procedures for and preliminary results of monitoring airborne, waterborne and groundborne vibrations with and without bubble curtains on a test project involving 2.438 m piles to 110 m is reported here. We observed fish kills and sea lions apparently fleeing the area. These phenomena were presumably due to the extreme acoustic effects of the powerful hammers which generated waterborne sound intensities locally in excess of 240 dB. This waterborne pile driving noise data collection undertaking is believed to be the most extensive ever attempted.

Jan 1, 2001

By Tara Schenk-McFarland, Mark Bliss

Echo Dam, located near Coalville, Utah, is a facility that provides storage for irrigation and municipal use. Original construction of the dam was completed in 1931. Because of seismic concerns, the spillway crest structure and upper chute section, founded on old landslide and colluvial material, were recently replaced. Prior to replacement of these structures, jet grouting of a block of the loose and potentially liquefiable soils, directly beneath the spillway crest structure was selected as the preferred alternative to address the potential for settlement and cracking of the spillway crest structure. The replacement or alteration of the in-place soil reduces the likelihood of seismic-induced excess pore pressure development and subsequent settlements. Core drilling and sample recovery of the production jet grouted columns was completed to verify compliance with the specifications. It was recognized that due to the larger rock sizes within the deposits that full homogeneity of the jet grouted zone was unlikely to be achievable. However, the purpose of this jet grouted section was to strengthen enough of the soil so that widespread liquefaction does not occur. During the jet grouting production many instances of ground fracturing occurred. Fracturing was evident based on grout/air bubbles exiting the surface near some of the grout holes during jet grouting, air bubbles appearing in the spoil pits, and lifting of the ground surface in the vicinity of the monitor during the jet grouting process while the system was pressurized. In one instance, a section of the upstream spillway slab, which was left in place, was cracked due to pressurized grout escaping beneath the slab. The overall results of the jet grouting were satisfactory despite difficulties encountered. The cause of the fracturing is hypothesized and a recommendation is included to reduce the likelihood of this occurring on future jobs.

Jan 1, 2017

By Shahid Islam, Lucian Bogdan

"The maintenance of infrastructures has been of particular concern to the engineering community. As the world’s infrastructure expands and existing infrastructure ages, monitoring and evaluation of the structures have become more critical than ever. A large number of retaining walls, tie backs, slope stabilizations and piles are designed using pre-stressing steel. Many piles and drilled shafts are designed using reinforcing steel. There are few testing methods available to assess these tension and compressive forces. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYWIDAG-Systems International (DSI) has been involved in the development, testing and utilization of DYNA Force® sensors to measure the force in the anchors during construction and at any time during the lifetime of the structure. They can be used for bare, epoxy-coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the anchor. The sensor is robust and requires no maintenance. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. This paper describes its application in tie-back and anchor force monitoring of retaining walls and bridge abutment and compression forces in drilled shaft reinforcing steel where the data were collected manually, automated and remotely.INTRODUCTIONOur infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.The elasto-magnetic (EM) technology is a novel approach to monitor forces in steel elements. The DYNA Force sensor is built based on EM technology (See Fig. 1). It is composed of a primary coil and a secondary coil (sensing coil). By passing current through the primary coil, ferromagnetic material is magnetized. The sensing coil picks up induced electromotive force that is proportional to change rate of applied magnetic flux (Faraday's law) and relative permeability. As permeability of core changes, output voltage changes. The output voltage is calibrated to measure the force. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. The sensor has an embedded thermistor which allows for temperature compensation. Due to the diversity of the magnetic property of steel, calibration is done for each type of steel allowing the sensors to perform at their highest accuracy."

Jan 1, 2017

By Lois G. Schwarz

I did a project (Sungai Piah) as a consultant to your firm in Malaysia, where we were faced with a similar situation as sketched out in your question. The following is what we did for the grouting of the primary holes, which were both located upstream of the plug as well as downstream: We used a hydrophobic MDI based semi-rigid polyurethane prepolymer in the first phase of the grouting operation when grouting under water flow conditions. Then in the second phase and also for the contact grouting we used a two component water compatible polyurethane elastomer. And then for deeper formation grouting, when all the water flow had been stemmed in the vicinity of the plug, we used a regular (balanced stable) cement based grout. So it may not exactly answer your question, but we first used hydrophobic grout because it is very efficient to grout a formation through which water flows. We didn&apos;t stop all the leaks day-lighting downstream of the plug or all water running through the formation near the plug, but the flow of water through the rock formation adjacent to the plug was reduced by 99.9%, after completing the urethane grouting. This facilitated the placement of cement based suspension grouts without wash-out.

Feb 10, 2003

By Emad Farouz

This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule. This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.

By Stefan Larsson, Jan Ekström, Jennie Kock-Larsen, Håkan Garin

"This paper describes the testing procedure (or protocols) for quality control of dry deep mixing columns in a major ground improvement project carried out in Sweden. Quality control was mainly based on column penetration tests performed at different stages in the project and on two occasions after installation. In the paper, the results from the tests are compared with tests on the unimproved clay. As expected, the results show that the correlation between undrained shear strength in the columns and in the unimproved soft soil depends mainly on the in-situ stress. However, the correlation probably depends on when the tests were performed after mixing. When the influence of the in-situ stress was excluded from the analysis, no significant correlation could be identified. This means that the undrained shear strength in the columns and in the unimproved soft can be considered to be uncorrelated when the strengths and the corresponding variability are evaluated with depth from groups of tests.INTRODUCTIONQuality control and quality assessment of deep mixing (QC/QA) constitute a key component in verification of the limit state design. Due to the complex mixing process and varying geological conditions, it is normally not possible to sufficiently assess the strength and deformation properties in advance. In Sweden, the most commonly used QC/QA method for verification of the limit state is the column penetration test (Axelsson and Larsson 2003; Bergman et al. 2013). The method works well but is time-consuming and requires many tests since property variability is normally high. The column penetration test can be used to assess the undrained shear strength Cu,col. However, it is not clear how the strength correlates to the undrained shear strength of the unimproved soil Cu,soil. There are common factors such as the in-situ stress state and the natural water content, which makes a positive correlation probable, i.e. as Cu,soil decreases, Cu,col also decreases and vice versa. The unimproved soil has a natural spatial variability, but it is not known if the improved soil follows the same variation. The mixing process has a substantial influence on the strength variability and may supersede the influence of other factors. However, if a sufficiently good correlation exists between Cu,col and Cu,soil, information from the geotechnical ground investigations can be used in the design and planning of QC/QA of deep mixing in a more stringent manner. Information about the correlation is also essential in reliability based design, where a strong positive correlation may have a negative influence on reliability. However, as discussed by Al-Naqshabandy and Larsson (2013), this correlation may be weak or insignificant for a representative failure domain where the mixing process may have a dominant influence on the strength variability. It is thus of interest to assess the correlation."

Jan 1, 2015

By Gerald Verbeek, Erick Baziw

Stone columns are used in geotechnical site remediation to increase load-bearing capacity and reduce settlement of foundations. Stone columns also improve slope stability and increase the shear strength of a soil. A very challenging problem is to characterize the in-situ shear wave velocities from data acquired from Downhole Seismic Testing (DST) after the insertion of stone columns. DST is an important geotechnical testing tool for site characterization that provides low strain (<10-5) in-situ interval compression and shear wave velocity estimates, but the postanalysis of seismic data acquired from DST in the presence of stone columns is very challenging due to the resulting complicated in-situ soil conditions. To obtain the right results it is necessary to use an algorithm that incorporates source wave raypath refraction. Starting with the Normal Moveout Seismic Cone Tomographic Testing (NMO-SCTT) algorithm developed some years ago, this paper outlines the modifications and additions made to this NMO-SCTT algorithm to facilitate stone column site characterization. To dramatically reduce the optimal solution space for the estimated interval velocities the paper also described a priori conditions that are applied based on the unique nature of the stone column site conditions.

By Ke Yang, Robert Liang

"Drilled shaft foundations are widely used for many types of structures, especially for highway bridges, high rise buildings, and costal structures. The lateral design considerations are crucial for those structures that are subjected to lateral thrust forces, winds, waves, and earthquakes. The p-y analysis is the most widely used method for the analysis and design of drilled shafts for lateral load applications in soils. However, existing p-y criteria were developed based on the lateral load tests on small diameter drilled shafts in soils. Although, a lot of lateral load tests have been conducted, there are a limited number of lateral load tests on large diameter drilled shafts embedded in clay. In this paper, a lateral load test on 2.44 m diameter fully instrumented drilled shafts in clay is presented. The site specific p-y curves are derived based on strain gage readings. The existing p-y curves are found to be much softer than the site specific p-y curves. Correspondingly, the deflection at the top of the test shaft under the maximum applied load is predicted to be eight times larger than the measured value using existing p-y criteria. A new p-y criterion is proposed in this paper. The proposed p-y criterion is proven to be able to capture the site specific p-y curves of the load test and to predict closely the deflections at the top of the test shaft. INTRODUCTIONDrilled shaft foundations are widely used for many types of structures, especially for highway bridges and costal structures. The lateral design considerations are crucial for those structures that are subjected to lateral thrust forces, winds, waves, and earthquakes. Although efforts have been made on studying lateral response of drilled shafts; nevertheless, only limited studies have been published on the behavior of large diameter drilled shafts under lateral loads and the corresponding design methods."

Jan 1, 2005

By Song-yu Liu, Chao Yan, Yong-feng Deng

"In order to investigate the stability of embankment on soft subgrade improved by T-shaped deep mixed column composite foundation, the internal forces and failure modes of columns were analyzed on the shape of critical slip surface and the displacement fields of composite foundation through strength reduction method of three dimensional numerical simulation. Then comparison between T-shaped and conventional deep mixed column composite foundation were conducted. The simulation results indicate that the stability analysis was overestimated by limit equilibrium methods. Piles within the slope shoulder provide great resistance slide effect through the vertical bearing capacity, while the piles nearby slope shoulder and outside slope shoulder providing great moment to resistant slip. The embankment stability of T-shaped deep mixed column composite foundation is higher than that of conventional deep mixed column composite foundation while cost less cement and construction time.INTRODUCTIONThe soft soil has many unfavorable project properties such as high compressibility, low strength, and high water component. Embankment built on the soft soil will face subsidence, horizontal displacement and stability problems. Cement-soil deep mixed column composite foundation is more commonly used as a method for construction of embankment on soft ground [1-2]. For the existing problems of China's current cement-soil pile (wet jet mixing pile), including strength uneven, effective treatment with shallow depth and high cost, a new technique, T-shaped bidirectional deep mixed column, is introduced [3]. An automatic expanding mixing blade was developed by Liu et al. shown in Figure. 1, to install TDM columns [4].T-shaped deep mixed (TDM) column combines bi-directional deep mixing technique and T-shaped deep mixing technique: ?Using concentric biaxial drill pipe, opposite rotational direction of the blade on the inner drill pipe and the outer drill pipe. By squeezing action of the blade on the outer drill pipe, forward and reverse rotation of the blades bidirectional mixing at the same time, blocking the way to take the grout, the uniformity of cement mixing is improved. ?Scalable stirring blades, which can be stretched for two different radius at any depth below ground, expand cross-section of the upper pile (enlarged head), forming expanding cross-section within the upper part of a certain depth which is similar to the shape of nail. As a new composite foundation, T-shaped mixing pile composite foundation is widely applied. However, studies on the stability of T-shaped column treated soft subgrade are rare in the research. So the stability study on T-shaped column composite foundation under embankment for guiding the design and construction has important significance."

Jan 1, 2015

By C. Guney Olgun, Mohammad Khosravi, Daniel W. Wilson, Deepak Rayamajhi, Scott A. Ashford, Shuji Tamura, Ross W. Boulanger

"Dynamic centrifuge tests were performed on unimproved and improved soil with soil-cement column models. The reinforcing effect of isolated soil-cement columns for reducing liquefaction potential and ground deformation in improved soil were investigated. This paper presents the observed acceleration, pore pressure, and settlement responses under an earthquake base motion for both unimproved and improved soil models. In addition, lateral reinforcing effects of soil-cement columns were also investigated in terms of site stiffening effects and the increasing natural frequency of improved soil. The test results show that the soil-cement columns were rather ineffective in preventing liquefaction triggering in improved soil and in significantly reducing the magnitude of the resulting soil settlement compared to the model with unimproved soil profile. Furthermore, the predicted natural frequency of the improved soil profile estimated using existing design equations is shown to be significantly higher than the observed natural frequency inferred from centrifuge tests results. These design equations assume shear strain compatibility between the columns and the surrounding soil. On the other hand, revised design equations that account for shear strain incompatibility between column and surrounding soil are shown to give reasonable estimates compared to the observed natural frequency of the improved soil model.INTRODUCTIONGround improvement using stiff columns (e.g., stone columns, deep-soil-mixing columns, and jet-grout columns), are often used in practice to reduce liquefaction potential (and associated deformations) in loose soil sites. Typically, saturated silty soils are difficult to densify or drain rapidly due to their lower hydraulic conductivity, so densification and drainage techniques of improvement are often found to be ineffective. Instead, the shear reinforcing mechanisms of stiff columns are considered effective for reducing the seismic stresses and strains, and thereby reducing liquefaction potential in the enclosed saturated silty soils (Baez 1995, Adalier and Elgamal 2004, Mitchell 2008)."

Jan 1, 2015

By K. Rainer Massarsch

"Part 2 of 2 (Continued from Summer 2004 edition) By K. Rainer Massarsch, Geo Engineering AB, Stockholm, SwedenVibrations, which are caused by the installation of piles in dry or permeable soils, can cause settlements. The magnitude of settlements depends on several factors, such as soil type and stratification, ground water conditions (degree of saturation), pile type and method of pile installation (driving energy). A method of settlement prediction due to construction-induced vibrations has been presented by Massarsch (2000). However, in many cases, an engineering assessment must be made at an early stage of a project. The following simplified procedure can be used to estimate settlements in a homogeneous sand deposit adjacent to a single pile, Fig. 5. This approach is based on extensive experience from soil compaction projects. It is assumed that intense densification due to pile penetration occurs within a zone corresponding to three pile diameters. The volume reduction resulting from the propagating vibrations will cause settlements in a cone with an inclination 2V:1H, with the tip at a depth of 6 pile diameters. Thus the settlement trough will extend a distance of 3D+L/2 from the centre of the pile, with maximum settlements at the centre of the pile. Maximum settlements, Smaxand average settlements, Smax can be estimated using the following relationship, choosing an appropriate a value of the soil compression factor, from Table 2.The driving energy depends on the method of pile installation, soil stratification and the pile type. The displacement volume of the installed pile has been neglected. The simplified method is applicable for estimating settlements at the perimeter of a pile group. It should be noted that settlements also occur outside the assumed cone, but these are often negligible. The effect of incompressible layers should be taken into account by adjusting the effective pile length."

Jan 1, 2004

By William H. Walton, Clyde N. Baker Jr., Darren S. Diehm

"A 51-story concrete core and steel frame commercial office tower was recently constructed on the site of the former US Gypsum building in downtown Chicago, Illinois, USA The structure foundation reused several caissons from the demolished US Gypsum building supplemented with new belled caissons bearing on silty clay hardpan. Extensive in-situ pressuremeter testing was performed during the geotechnical investigation to determine allowable bearing capacity and better estimate building settlements. Problems during foundation construction along the south side of the building frame required remediation of two caissons. One caisson was supplemented with micropiles, while the second caisson was abandoned and replaced with a straight-shaft rock socketed caisson. To determine the effectiveness of the repairs, the building foundation settlements were monitored during construction.IntroductionIn 2001, The John Buck Company began development of a new office tower at the southeast corner of West Monroe Street and South Wacker Drive in Chicago, Illinois. The site was formerly occupied by the 18-story US Gypsum (USG) building. Mr. Clyde N. Baker, Jr. (Senior Principal at STS Consultants, Ltd .) served as the foundation engineer for USG which was completed in 1962. The building was founded on a forest of belled caissons bearing at elevation -56 Chicago City Datum (CCD). For reference, the ground surface at Upper Wacker Drive is approximately elevation +20 CCD. The bearing material was a hard silty clay, locally described as Chicago Hardpan. The foundation caissons were designed using an allowable bearing pressure of 16 ksf (766 kPa). In 1996, the USG superstructure was razed, and the three-level basement was converted to an underground parking ramp.South Wacker DevelopmentThe 51-story high-rise building was completed in 2005 with a structural height of 681 feet (208 m), and an internal space of more than 1,000,000 square feet (93 ,000 square meter). The typical floor size is 27, 700 square feet (2, 570 square meter). Renderings of the building are provided in Figures 1 and 2. The largest single tenant is the accounting firm of Deloitte & Touche, which occupies roughly 45% of the building space with over 3,000 employees."

Jan 1, 2005