Search Documents

By Roberto Nova

The selection of the Osterberg Cell (O-Cell) technology as the standard testing method for deep foundations of the Railways Po Viaduct in Northern Italy offered a relevant number of field measures on large bored pile behaviour in alluvial soils. The assessment of pile response during such ?non standard? testing procedure was performed through the comparison with standard top load tests on companion piles as well as by numerical models of the tests including a simplified pile-soil interaction scheme. As shown in this paper, the O-Cell technology allowed a careful assessment of the non-linear pile behaviour even at quite small loading levels as those required by a posteriori proof tests on production piles. Simple numerical models proved to be very effective in the simulation and the interpretation of pile behaviour during such unconventional testing procedure.

Jan 1, 2008

By Walter G. Brusey

This paper describes a comprehensive pile test program conducted at John F. Kennedy International Airport (JFKIA) to evaluate pile types and design capacities ranging from 890 to 4450 KN (100 to 500 tons). Driven cased piles and drilled shafts, both standard construction and post-grouted after installation, were tested with platform loads extending to 8900 KN (1,000 tons). Alternate load test procedures were developed, extensive structural integrity testing and dynamic load tests were performed on selected shafts. A brief update is provided covering the application of results of the test program to pile selection for support of major structures incorporated in the on going redevelopment of JFKIA.

Jan 1, 2000

Jan 1, 2005

By Pirooz Barar

The new Stanley Hall building will house the center for bio-engineering and technology research for the UC Berkeley campus. The structure is located at the northeast part of campus, adjacent to Donner Lab, on the west side of Galey Road, approximately 600 ft. from the Hayward Fault. The building site has a complex geological formation. To the east there are clayey soil shale formations, and to the west there is greywake shattered sandstone. The water table is at 10 ft. below grade. The structure will consist of 6 levels below grade and 8 levels above grade, which calls for an 83 ft. deep excavation on the northeast side. There is an approximately 35 ft. grade differential between the east and west sides of the building. Because of this severe grade differential, as well as high water tables, the lateral forces on the building due to uneven earth pressures would have been 2 times the magnitude of the seismic forces. To mitigate the lateral earth pressures, a permanent Soil Nailed Wall, integrated with the structural system of the building was designed. PB&A, Inc.?s in-house design program ?Winslope? was utilized to design the system and the data obtained from a rigorous monitoring program, were used to calibrate several computer runs using Plaxis program.

Jan 1, 2004

By Clifford J. Wren

A geotechnical foundation solution was required to halt and prevent further structural distress suffered by a residential four storey apartment building in Hamilton, Scotland. Residents of the ten year old building started to notice cracking and signs of distress approximately one year after moving into the property. A detailed intrusive inspection of the structure revealed that the building was moving and had suffered significant settlement and structural distress at the shared party wall between it and an adjoining building. Roger Bullivant Limited (RBL) was appointed Principal Contractor to carry out an agreed remedial works contract which included a complete structural ?strip-out? of the ground floor, underpinning, contiguous bored pile retaining wall and reinstatement. The paper describes how a proprietary pile and needle beam underpinning system was used to prevent further differential movement and provide a new secure foundation for the residential building. The case study illustrates how a flexible problem solving approach can be applied to a difficult and sensitive geotechnical project.

Jan 1, 2008

By Tanaya Deb, Sujit Kumar Pal

"Experimental investigations are carried out on failure pattern around 2D models of belled anchor piles in dry sand bed of density 15.60 kN/m3 under uplift. The models are having thickness ratio (Ts/Tb) = 0.28, 0.32, 0.38 and 0.46 and total 12 numbers tests are performed on models possessing 45° bell angle and shaft thickness 26 mm. The foundation bed is prepared with alternate dyed and non-dyed sand layers and continued upto reaching embedment ratio of 3, 4 and 5 for each width ratio. The failure points are presented with respect to meridian section of anchor in X-Y coordinate system and the equations formed are of polynomial of degree 3; and R2 values are near about 1. The developed wedge is implemented as three-dimensional axisymmetrical failure surface around similar 3D models. In the horizontal slice method vertical limit equilibrium is used for calculating weight of wedge and mobilized shear (as per Chattopadhyay and Pise, 1986) on the slip surface of each element. The summation of all elementary forces demonstrates gross uplift capacity. The initial and final failure angles are detected and parametric study is conducted on failure pattern as well as predicted net ultimate uplift capacity. Almost all the analytical data are within ± 10% variations with respect to the experimental results of uplift capacity which shows better correlations. INTRODUCTION Belled or enlarged base anchor piles are attractive and economic alternative to the geotechnical engineers for compressive load bearing capacity as well as tension anchorage. These types of anchors may be useful for foundations erected below ground water table. In light weight structures like radar tower, television tower, power pole and outdoor sign pools imbalance horizontal forces due to wind loads, are more than of those self-weight of those structures. Due to chronic tensile loads most possibly from wind loads and associated imbalanced cable tension, the legs of power transmission tower should be properly designed to be safe against resultant pull-out forces. In belled anchor pile, uplift is influenced by embedment ratio, diameter ratio; so, contributions of these parameters on failure surface influence uplift capacity. Balla (1961) first introduced non-linear failure surface in the pattern of circular arc based on Kotter’s equation (1903) and soil friction was assumed to act on slip surface. The predictive mathematical models established by Matsuo (1967), Rao and Kumar (1987), Chattopadhyay and Pise (1986), Saeedy (1987) and Ghaly and Hanna (1994); it was reported that net ultimate uplift capacity was combination of bulk weight of failure wedge and shear resistance along slip surface acting in opposite direction of wedge movement. From the literatures available till date, it reveals that the contribution of mobilised shear and weight of breakout wedge separately, demanding for more clarification depending on the on parameters like embedment ratio, diameter ratio."

Jan 1, 2015

By Bill Zietlow

A micropile and soil nail underpinning system was installed to support a building immediately adjacent to a 25-ft deep excavation in downtown Salt Lake City, Utah. Both the building and the underpinning were instrumented to monitor deflections, rotation and crack growth. The underpinned structure consisted of a two story concrete masonry unit (CMU) building founded on shallow spread footings attached to a concrete high-rise building on spread footing two floors below grade. The face of the excavation was 10 in. in front of the underpinned building foundation wall. The underpinning system consisted of small diameter hollow bar micropiles installed with injection grouting techniques below the bottom of the excavation and attached to the underpinned structure by a concrete pile cap doweled into the existing footing. The lateral loads imposed by the soil under the underpinned structure were designed to be supported by the soil nail wall installed through the micropiles during excavation. The settlement monitoring instruments consisted of crack gages, optical survey prisms, high sensitivity vibrating wire water levels and biaxial vibrating wire tilt meters. They recorded maximum movements of approximately 0.1 in. of settlement, 0.05 deg. rotation (top of wall rotating away from excavation) and up to 0.08 in. of crack opening during the excavation until one month after the soil nails and shotcrete facing were completely installed. This movement was well within both the estimated settlement and the estimated settlement tolerance of the underpinned structure.

Jan 1, 2008

By Peter J. Nicholson

Recognition of the liquefaction susceptibility of dam embankments has been heightened since the San Fernando Dam near failure incident in 1971. Both the downstream and upstream slopes of dams can be at risk for slope failure that can lead to breaching of the dam during or after a seismic event. Many dams have been remediated by various means such as the installation of stone columns or by excavation and replacement of the liquefaction susceptible material. Recent engineering and technology advances in equipment and materials has shown that construction of shear walls to the appropriate depths and at the right center to center spacing may be an economical alternative to the more traditional methods. Recently, the downstream embankments of at least 4 dams, from South Carolina to California, have been, or in the process of being remediated by the use of shear walls. The method of installation has been either multi-axis Cement Deep Soil Mixing walls or walls constructed by the use of trench excavation under self-hardening slurry. Four case histories of dam remediation are discussed, three by multi-axis paddle auger CDSM equipment one with the use of self hardening slurry trenches.

Jan 1, 2008

By Ørjan Nerland, Torgeir Haugen, Astri Eggen, Kjell Karlsrud

"Ground improvement by the deep dry mixing (DDM) method is used in Norway since the late 1970's. A brief review is given of the Norwegian guideline for ground improvement with DDM issued in 2012, but focus is on practical examples and experiences related to improving the stability of excavations and natural slopes in soft clays. Two examples deal with experiences from 10 to 18 m deep excavations in soft and partly highly sensitive clays, where DDM panels and block stabilization were used to both give sufficient stability against bottom heave and to limit lateral wall displacements. A third case deals with improving the stability of a natural slope in quick clay by installing DDM panels near the crest of the slope. To limit disturbance and excess pore pressures generated during the DDM works, vertical drains were installed in advance in between the DDM panels. This ensured that the excess pore pressures generated by the DDM works (up to 150 kPA) dissipated quickly, which was instrumental to avoid triggering a landslide during the stabilizing works.INTRODUCTIONThe lime column (LC) method developed in Sweden and Japan in the mid 1970's (e.g. Broms and Boman, 1977). Since then, there have been significant developments in Scandinavia and around the world in terms of rigs, mixing machinery and tools, and type of binders used. The method, presently named the ""Dry Deep Mixing"" (DDM) method in contrast to the wet deep mixing methods (WDM) that also have developed significantly over the past decades, e.g. Kitazume and Terashi (2013). The first application of the DDM method in Norway was in the late 1970's to improve the stability of an excavation in quick-clay, then using only lime as binder. Most DDM applications in Norway have also thereafter been to improve the stability of cuts, supported excavations or natural slopes in soft clays. The Norwegian Geotechnical Society (2012) issued in 2012 “Guidelines for design of ground improvement with DDM methods"". The following highlights design issues dealt with. The paper focuses however, on some practical cases where DDM has been used to improve stability of deep excavations and a natural slope in soft and partly highly sensitive clays."

Jan 1, 2015

By Olgun

Energy piles are a new innovative renewable energy technology to access and exploit the relative constant temperature of the ground for efficient heating and cooling of buildings. Examples of energy piles include drilled shafts, continuous flight auger (CFA) piles, driven piles, and micropiles. A field test setup was installed at the Virginia Tech Geotechnical Research Facility to study energy piles. The field test consists of a total of five micropiles 25 cm (10 inches) in diameter, four of which were equipped with circulation loops. The test piles extend to a depth of 30.5 meters (100 feet) and are heavily instrumented with strain gauges and temperature sensors. Several observation boreholes were formed around the test piles to monitor ground temperatures. Thermal conductivity tests and field load testing were performed to investigate the behavior of Energy Piles. This paper presents results of the thermal conductivity tests and thermo-mechanical field load test performed as part of this field investigation.

By R. K. Filip

"Steel bearing piles have long been used to carry high compressive, tensile and lateral loads. Such piles are most commonly tubular or ""H"" profile and are typically installed using percussive techniques. The noise and vibration associated with such installation techniques tends to preclude the use of steel bearing piles in urban and other sensitive areas.This paper describes the design and construction of an innovative new road bridge in Milton Keynes, UK. The steel bearing piles were required to continue out of the ground to form the bridge columns and abutments and then be cast directly into the soffit of the reinforced concrete bridge deck. This project was to be the first time in the UK, that this form of bridge design had been used.The paper shows how new installation techniques allowed the designers to use these high capacity steel elements in a sensitive urban environment without the use of percussive or vibratory installation techniques. Finally the paper shows how these quiet and vibration-less installation techniques can be extended to other applications.A UNIQUE BRIDGE SUPPORTED ON ""BOXED SHEET PILES""CONCEPT HISTORYThere are over 700 bridges in Milton Keynes. Concrete is the dominant construction material, most are single span with massive parallel wing wall retaining abutments. All have a certain uniformity of aesthetic design. Pell Frischmann Consultants Ltd (PFC) proposed to the client, English Partnerships (EP), that an ""integral bridge"" with a slender open appearance would be an appropriate aesthetic form for a new highways bridge, within the district of Westcroft (figure 1). The concept required that the bearing piles be continued up out of the ground to form the bridge columns and abutments. Four rows with four piles in each row were suggested. Each would then be cast directly into the reinforced concrete bridge deck forming a moment connection (figure 2). This concept meant that a single continuous steel structural member would replace traditional reinforced concrete bored piles, pile caps and piers. This member would carry vertical and lateral loads. The conceptual design was intended to meet the following client requirements:"

Jan 1, 2005

By Dominic Parmantier, Jason Page

"In the past, the designers of DSM have analyzed various failure modes and then specified a minimum unconfined compressive strength (UCS) for the soil-cement. The specified minimum UCS reflected the compressive stress in the soil-cement under design loads and an appropriate factor of safety. With the increased use of finite element analysis for the design of DSM applications where allowable strain as well as stress are considered, there is a growing trend for designers to specify a modulus and occasionally a tensile strength for the soil-cement in addition to the UCS. This paper compares the relationship of modulus and tensile strength to UCS for soil-cement from a recent DSM project with unique testing requirements. These results are compared to published data. The case is made that designers should utilize published relationships to characterize the required strength and stiffness by a single acceptance criterion: UCS.INTRODUCTIONAs the use of DSM has increased in popularity so has the use of service state deformation analysis in lieu of more traditional failure mode analysis. Most DSM designers are interested in the appropriate modulus values and occasionally tensile strength values of soil-cement as well as simply the unconfined compressive strength (UCS) of soil-cement.Although there are numerous published correlations between the UCS, tensile strength and modulus of soil-cement, some DSM project specifications are produced which have acceptance values for tensile strength, modulus, and UCS. If this specification of multiple strength properties is consistent with the nature of soil-cement, then there is really no harm except for the expenditure of client money on unnecessary testing. If however the multiple strength properties specified are inconsistent with the material properties of soil-cement, then the specifications can create the expectation that the DSM contractor can somehow create a custom soil-cement with tensile strengths and modulus characteristics which are unachievable.This paper presents a brief summary of a project in Burnaby, B.C. which specified minimum values for the tensile strength, modulus, and UCS of the soil-cement. A comparison of those test results to published correlations between the UCS and the tensile strength is presented. Additionally, a comparison of modulus derived from two different methods of testing is presented along with a comparison to published correlations between UCS and modulus for soil-cement."

Jan 1, 2015

By Vivek Samu, Murthy Guddati

A new method called Effective Dispersion Analysis of Reflections (EDAR) was recently developed to effectively analyze the dispersive waves generated from lateral impact to piles. This paper presents the results of nondestructive length estimation of existing piles through EDAR. EDAR provides a new visualization method for analyzing wave reflections by transforming the response into the frequency domain thus eliminating the need to perform difficult peak picking in the time domain. In addition to being able to analyze dispersive waves, EDAR also incorporates the effects of radiation damping due to the surrounding soil leading to more accurate length estimates. Concrete filled steel tubes of different embedment depths were tested both in laboratory and field conditions. Length estimates obtained were within 10% error margins after careful analysis accounting for the presence of soil effects and effects from pile top reflection.

By Jeongbok Seo

This paper describes successful application of driven tapered-steel-pipe piles for two large-scale projects in the New York metropolitan area: Rego Park Mall, Rego Park, N.Y. and 164 Kent Avenue, Brooklyn, N.Y. The combination of side friction and end bearing resistance produced by tapered-steel-pipe piles has been well-recognized as greater than the side friction and end bearing resistance by pipe piles. Forty-four tapered piles were driven and tested at these two sites. Design pile load for the two sites was 260 kips for Rego Park Mall and 400 kips and 300 kips for 164 Kent Avenue. To measure the pile-drive hammer efficiency, the compressive stress in the pile, and to estimate the ultimate bearing capacity of the pile, dynamic load testing using a Pile Driving Analyzer (PDA) was conducted on index piles at the sites. Subsequent to the field testing, data analysis using the Case Pile Wave Analysis Program (CAPWAP) was conducted. Restrike PDA analysis and full-scale static load tests were performed on the selected test piles. Test piles at the project sites exhibited significant time-dependent increases in bearing capacity caused by the effects of "set-up" or "soil freeze." The dissipation of excess pore-water pressure in the soil, which had been disturbed and remolded by driven pile, was generally considered the primary cause of set-up. The increase at the subject sites ranged from 100 to 300 percent of the capacity measured at the initial driving. This paper discusses the results of various types of load testing on tapered piles and the set-up effects by comparing PDA test results acquired during and after pile driving. Finally, an empirical relationship for the New York metropolitan area has been offered for quantifying set-up.

Jan 1, 2008

By Charles M. Wilk

"Solidification/stabilization (S/S) treatment is used to treat hazardous wastes for disposal and in the remediation/site restoration of contaminated land . SIS is also an increasingly popular technology for Brownfield (industrial property) redevelopment, since treated wastes can often be left on-site and to improve the soil for subsequent construction. This paper discusses the applicability of the technology to various wastes, basic cement chemistry relating to SIS, tests used to design treatability studies and to verify treatment, basics on implementation of the technology in the field , and examples of SIS use at brownfield sites, including a former wood preserving site, former manufactured gas plant sites, a former electric generating station, and a shopping mall development.INTRODUCTIONSolidification/Stabilization (S/S) is a widely used treatment for the management/disposal of a broad range of contaminated media and wastes; particularly those contaminated with substances classified as hazardous in the United States. The treatment involves mixing a binding reagent into the contaminated media or waste. The treatment protects human health and the environment by immobilizing contaminants within the treated material. Immobilization within the treated material prevents migration of the contaminants to human, animal and plant receptors. SIS treatment has been used to treat radioactive wastes since the 1950s and hazardous waste since the 1970's (Conner 1990). SIS continues as a cornerstone treatment technology for the management of radioactive waste, hazardous waste, and site remediation and Brownfield redevelopment."

Jan 1, 2005

By Juan M. Pestana-Nascimento, Robert G. Bea, Hamed Hamedifar, Emery M. Roe

The current State-of-the-Practice is grounded heavily on deterministic characterization and assessment of the performance of civil engineering infrastructure. In particular, flood defense systems, such as levees, have been evaluated within the context of the Factor-of-Safety where the computed capacity of the system is compared with the code specified demand forces. Uncertainties associated with the capacity and demand forces render deterministic modeling incomplete. In particular, two structures with the same Factor of Safety can have vastly different probabilities of failure. While efforts have been made to assess levee vulnerability, results from traditional engineering approaches omit important factors because they do not account for uncertainties included in analytical modeling, and natural variabilities, or human and organization factors. This paper utilizes risk assessment methods to advance methods for quantifying the contribution of uncertainties to engineering analyses, and thereby provide additional information to help assess sustainability of geotechnically engineered systems. The probability of failure of a geotechnically engineered system is directly impacted by how well the system is understood, and how uncertainties are incorporated in development of understanding of the system. This paper presents methods to evaluate two types of uncertainties for three potential failure modes of flood protection levees: underseepage, slope (or levee) instability, and overtopping/erosion. These analyses account for two types of uncertainty: 1) Type I – inherent uncertainty, 2) Type II – analytical modeling uncertainty. Human and organizational task performance and information development and utilization uncertainties are not included in these analyses. This paper focuses on the behavior of the flood protection levee system for Sherman Island, a western island in California’s Delta. Sherman Island is of critical importance to California because of the very important infrastructure systems that pass under, on, over, and adjacent to Sherman Island, including: natural gas pipelines, regional and interregional electricity transmission lines and telecommunication facilities, two deepwater shipping channels; and State Highway 160, a link between major transportation expressways. The work evaluates current (year 2010) and future conditions (year 2100) and incorporates variations in capacity and demand arising from projected human response activities and global climate change.

Jan 1, 2017

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

Using sheet piles and pipe piles for permanent earth retaining is one of the most economical methods for constructing basement walls since they can also work as temporary shoring during construction. A major mixed-use redevelopment project in the UK, encompassing two to three large city blocks, utilized both sheet and pipe pile walls for a two-level subterranean parking structure. The 290m (950ft) x 100m (330ft) basement’s steel walls were designed to temporarily support excavation during construction and eventually to become a load carrying permanent structure in order to expedite the construction process and to achieve cost reduction. Two types of press-in piling machines, one for sheet piles and the other for pipe piles, were used for the job because of their abilities to press in sheet and pipe piles within tight tolerances for finished walls, for difficult installation conditions with very hard soil, and for its very low noise and practically zero-vibration operation; an essential factor for the job in close proximity to other businesses and residents. BACKGROUND Steel sheet pile and pipe piles have been used for many purposes including earth retaining. They are produced at steel mills and spirally welded at a fabrication yard to their corresponding specifications under strict quality control measures. Therefore, they can form highly reliable walls to its design capacity with proper installations. Their advantages as underground walls are:  They can form a high level of water cut-off function with their interlocks sealed by welding or with hydrophilic materials. See Figure 1 for a few examples for a sheet pile application.  They can carry vertical loading in addition to horizontal load and bending moment.  They can be a self-standing and temporary/permanent wall with flexible design and construction processes; bottom-up, top-down or hybrid sequences can be chosen per the project’s needs.  They can form a thinner wall than other wall types, creating larger inner space. See Figure 2.

Jan 1, 2019

By Jr. D'Angelo, Michael M. Blendy, Shawn Downey

"A grouted helical pile was used to support new buildings in the reconstruction of a large residential development. Foundation options were complicated by urban fill underlain with variable alluvial soil. A driven timber pile and grade beam system was recommended to support the new buildings. Other foundation options are also discussed. The grouted helical pile was quoted as an alternate and ultimately won the bid based on the economics and performance of the system. Data from 8 load tests was used to develop an empirical site specific relationship for determining pile capacity based on both installing torque and installation depth. Design to incorporate tolerance on installed pile location is presented. With the three phases completed, 554 residential dwelling units supported by 3645 grouted helical piles had been constructed covering 18 city blocks on the 44 acre site. IntroductionThe Philadelphia Housing Authority reconstructed the Tasker Homes housing complex located in southern Philadelphia, Pennsylvania, adjacent to the Schuylkill Expressway in the Grays Ferry area. Keating Building Corp. and Pennoni Associates were the general contractor and the structural engineer respectively. The original Tasker Homes development was constructed from 1940 to 1941 and consisted of 44 acres of primarily two and three-story residential brick buildings. These buildings were supported by a timber pile foundation system. The structural condition of the buildings supported on the timber piles was generally good in comparison to areas outside the buildings. These areas had settled possibly up to 2-feet in places due to the heterogeneous nature of the urban fill."

Jan 1, 2005

By Kyle A. Kershaw

The City of Grand Forks, North Dakota obtains drinking water from both the Red River and Red Lake River through a system of raw water intakes, shallow pipelines, and pump stations. However, during flood events, the City often loses access to the system, as evidenced during the record flood event in 1997. As a result, the City decided to construct a new gravity raw water intake system, including a pump station at the base of a 65-foot-deep, 60-foot-diameter caisson, behind a new levee system. Because of high design flood elevations and connectivity of river head to underlying soils, uplift resistance was required for the caisson. A total of 37, 2-foot-diameter, augered cast-in-place (ACIP) piles were chosen to provide uplift resistance. Because of the difficulties associated with installation of piles within the confined space of the constructed caisson and basal stability concerns, installation was completed from the existing ground surface to a depth of 120 feet. Several design and construction issues arose, including squeezing ground during pile installation, placement of long reinforcing bars, and installation of a dual material pile. A dual material pile was required to ensure that the ACIP pile below the base of the caisson was structurally sound and the pile above the base of the caisson could be easily excavated during sinking of the caisson. This paper discusses the solutions to each of these issues, as well as construction sequencing, load testing and integrity testing of the ACIP piles, and the successful completion of the project.

Jan 1, 2003

By Michael W. Oakland

This paper summarizes the analysis and design of a pile foundation system for two 400 ft. diameter, 500 ft. high cooling tower using a detailed finite element analysis package. The cooling towers are at the Brayton Point Power Plant in Somerset, Massachusetts. The design-build project will convert the power plant to a closed loop cooling system to reduce return of heated water to the bay. Each cooling tower is supported on a 5 ft. thick by 16 ft. wide ring beam with 44 columns oriented in a radial pattern. The allowable lateral movement on the thin wall shell was limited to only 0.5 inches. Lateral and tension resistance were the primary concerns for the large, but lightweight structure and the critical issue was the lateral response of piles and pile groups within the system. By constructing a detailed model of the foundation system including modeling each pile as an independent element, the contribution of each element was separately assessed and the system tuned to take best advantage of the load distribution afforded by the ring beam as well as the soil structure interaction created by tangential as well as radial resistance of the pile groups. The detailed model also incorporated the lateral resistance of interior piles supporting an equipment slab within the ring beam. Simpler models analyzed the pile groups independent of the complete structure and generally only relied on radial stiffness and generally resulted in large groups of piles needed at each pier. Through a series of trial configurations, the number of piles used was optimized. Confirmatory lateral, vertical and tension load tests were conducted and final fine tuning of the model completed.

Jan 1, 2010