Search Documents

By Dongwook Kim

Recently, load and resistance factor design (LRFD) is gradually being adopted internationally in geotechnical design due to the advantages of LRFD over the existing allowable stress design (ASD). LRFD is a more advanced design method compared to the ASD because resistance factor is calibrated based on the reliability analysis for a given target reliability index. Target reliability index changes with the importance of the structure. Typically, target reliability index of offshore foundation is less than those of onshore. The widely-used Imperial College Pile (ICP) design method is used for the calculation of pullout capacity of driven piles. The uncertainties regarding pullout capacities of driven piles are assessed using the statistical data reported in the literature. The first-order reliability method (FORM) is used to calibrate resistance factors for the pullout ultimate limit states of the driven piles for three different levels (2.5, 3.0, and 3.5) of target reliability index. The load factors used in this paper are the ones proposed in the AASHTO LRFD bridge design specifications.

Jan 1, 2010

By Nasr Sheta

"After Hurricane Sandy, the stability of an earth slope in the Atlantic Highlands, New Jersey in the United States was deteriorating due to slumping soils and erosion from flooding. A slope stability evaluation indicated the slope did not satisfy the requirements of the local building code. A triple-tier, pile-supported and mechanically stabilized earth wall was designed and constructed to stabilize the slope. The construction was planned from a 3-m-wide roadway and, because of rough terrain and limited work space at the site, a cast-in-place drilled-pile construction was deemed impractical due to slow pile production. An alternative procedure was utilized by pre-drilling holes, and installing precast tip-and-shaft-grouted (PCTSG) piles, which extended to competent soils to improve slope stability. A grade beam, connecting the PCTSG piles along with soldier beams and concrete lagging were used to form the lowest tier of the slope stabilization, while the middle and higher tiers were built as mechanically stabilized earth. The stability of the proposed stabilization was analyzed using 2-D non-linear finite elements. After construction, monitoring of the wall continued for about 8 months to check its performance, and indicated lateral and vertical wall movements were less than 25 mm and 6 mm, respectively, indicating effective slope stabilization.INTRODUCTIONStabilizing earth slopes using piles to connect near-surface unstable soils to underlying stable ground masses has been investigated by many researchers, who presented various approaches to evaluate the contribution of the pile system towards improving the stability of the slope. Some of these approaches consider the piles as structural elements receiving forces from the upper sliding ground mass and transmitting these forces to the underlying stable one. The force from the top sliding mass is applied at between one third and one half of the pile embedment into the top sliding mass, Anagnostopoulos et al. (1990), Fukuoka (1977) and Matsui et al. (1988). The point of application of the sliding force was explored based on successful case histories while addressing the safety factors for both geotechnical and structural design, Vessely A. et al. (2007). The development of numerical analysis techniques utilizing the method of finite elements (FE) also enabled better analysis and design of slopes stabilized using piles. A FE-based approach was successfully utilized to design slope stabilization with target safety factor based on the shear and bending demands and the spacing of the piles, Pradel D. et al. (2010).After Hurricane Sandy in October 2012, the stability of many properties constructed atop earth slopes located along the coast of the Atlantic Ocean has become a concern due to storm-induced erosion. This paper presents the analysis, design and construction of a hybrid slope stabilization system utilized at one of these storm-impacted properties, which is located in the Atlantic Highlands, New Jersey in the United States. The subject property consisted of a two-story residential dwelling and a parking structure, and was built on top of an about 8-m-high earth slope having crest at about elevation 10 m (el 10) and toe at about el 2."

Jan 1, 1900

By Maurizio Siepi, Paul van Horn, John Coupland, Julian Crawley

"TTMJ is the acronym for the Slurry (Diaphragm) Wall Tension Track Milled Joint currently in development as part of the European Union's innovative and far-reaching Horizon 2020 initiative (FTI Pilot-2015-1 720579). The TTMJ Project has been specifically set up to deliver this versatile new step-forward in Slurry Wall technology. The TTMJ System is protected by patent in Europe and the USA, and is currently under development by a consortium comprising Trevi SpA (Italy), Arup (Netherlands) and CCMJ Systems (UK). The principles of the TTMJ System together with the installation process are herein described in general terms. The system is still under development with field trials scheduled for early 2018, so some of the detail will not be disclosed at this stage. It is the intention of the Authors that the results of these field trials and a more complete description of the System will be presented in a paper we intend to submit for the DFI/EFFC International Conference on Deep Foundations and Ground Improvement to be held in Rome, Italy in June 2018. The final section of this paper explains how the TTMJ system can be applied to a common application of slurry wall construction; deep circular or multi-cell shafts. The system can be used to construct shafts more easily and at less cost than current methods. It also allows shafts with smaller internal dimensions to be constructed than is currently practical.INTRODUCTIONCCMJ Systems (UK) realised that an innovative new approach to forming joints in both Slurry (Diaphragm) Walls and Secant Pile Walls would provide greatly improved joint integrity to greater depths, to the overallbenefit of retaining wall quality, across the world-wide foundations industry.In particular this new system is designed to:??Increase the effective depth range of Slurry Walls (especially walls excavated by grab) and Secant Walls??Remove the requirement for Stop-ends or Joint Formers??Allow for a Shear Key at the joint??Allow for a Water Stop to be installed at the joint??Permit Continuous Reinforcement across the joint??Optimise Reinforcement Density and hence Concrete Flow??Facilitate joints in corner panels eliminating the need for “L” shaped cages and reducing largesingle-pour concrete volumes and slurry storage capacity requirements.??Enable the construction of smaller-dimensioned square and circular deep shafts (especially useful for city-centre sites) than is possible with current methods.CCMJ Systems approached other industry specialists with a view to forming a development team to explore the possibilities for this new technique."

Jan 1, 2017

By David Wilshaw

Continuous Surface Wave (CSW) testing has been the “next big thing” in ground characterization for the last 25 years. The technique uses surface geophones to measure the speed at which Rayleigh waves (generated by a vibratory source) travel through the ground over a range of frequencies. The velocity at which surface waves travel through the ground is directly related to ground stiffness; the velocity of shorter wavelengths is influenced by the stiffness of shallower soil layers, while the velocity of longer wavelengths is influenced by the stiffness of deeper layers. Measuring the surface wave velocity over a range of frequencies, therefore, allows a stiffness / depth profile to be produced. Using the small-strain stiffness data measured by the CSW technique greatly improves the accuracy of simple limit state analyses; the data are also of sufficient quality for use in Finite Element modelling. Nonetheless, the technique has suffered from a perception of high cost, low productivity, and poor repeatability. An improved Advanced Continuous Surface Wave (ACSW) testing system has been developed by Ground Stiffness Surveys in the United Kingdom, has been deployed there commercially for several years, and is now available in the United States. ACSW uses an automated electronic control system that generates vibrations (from a purpose designed and manufactured portable seismic “shaker”) at different frequencies, measured across a 3m (10-foot) array of geophones, linked to a robust data acquisition and analysis software package. The range of applications in geologic and geotechnical site characterization includes rapid preliminary non-intrusive site assessments (utilizing published soil correlations); stiffness profiling to detect discrete layers (such as a variation in rockhead); average stiffness profiling for earthwork or ground improvement control testing, Working Platform stability assessments, foundation settlement analysis, rock quality and rippability assessments, and void detection.

Oct 1, 2022

By S. E. Stallibrass, A. M. McNamara, J. P. Panchal, Leonardo M. LaLicata

Urban development in congested cities requires a better exploitation of the available surface, leading to taller structures. These buildings are usually founded on piles that have to be increased in dimension to accommodate the larger loads. Consequently, both the cost and the carbon footprint of the pile foundations rises. An alternative option is to improve pile performance by enhancing shaft capacity, which is commonly the most important factor in determining the ultimate capacity of a pile constructed in a clay soil subjected to axial load. For piles in stiff clays, such as London Clay, the soil/pile friction may be increased by profiling the side walls of a bored cast in situ pile with small discrete “impressions” such that the latter form nodules on the shaft of the concreted pile. The results from centrifuge and full scale field tests showed that the impression pile represents a viable technology to enhance the shaft capacity as they provide an increase in capacity of 40%. Alternatively, reduced length impression pile can be used. This paper explores the implications of the impression pile technology on the potential carbon saving.

May 1, 2022

By Eric P. Bregman

As part of an on-going effort to improve water quality and reduce discharge into Boston Harbor, the Massachusetts Water Resources Authority (MWRA) East Boston Branch Sewer Relief Project was designed under a Federal mandate from the United States Environmental Protection Agency (EPA) to upgrade the aging sewer system, increase system storage and greatly reduce the volume of combined sewer overflows into the Harbor. The project scope of work includes the installation of over 2 miles (11,800 linear feet) of 36-inch and 66-inch diameter sewer relief piping, twenty (20) temporary shafts and an approximate 100 foot open cut section, located within the densely populated neighborhood of East Boston, Massachusetts. This area is a former marshland backfilled in the early to mid 1800?s where busy commercial streets co-mingle with thickly settled residential houses. The subsurface conditions present within Boston?s complex geology include the presence of subsurface contamination as well as complex networks of underground utilities. Additional site limitations included low headroom, noise, and traffic restrictions. Together these limitations required the design of individual earth support systems, tailored for each shaft location. Moreover, challenging subsurface conditions identified during construction required design modifications to minimize cost and schedule impacts related to construction dewatering, treatment of contaminated groundwater, internal bracing, and utility relocations. This paper provides a case history of the Geo-structural design and performance of various earth support techniques utilized to construct jacking and receiving shafts designed to launch and receive two (2) micro-tunnel boring machines (MTBM) and to support the construction of new deep shaft structures in an urban coastal area.

By Rouzbeh Vakili, Adel M. Hanna

"The application of piled raft foundations has significantly increased during the last few years. In this system, the raft and the pile group collectively transfer the applied building load to the underlying soil layers. Determination of load sharing between the raft and the piles derives the complexity of piled raft designs due to its multi-parameter nature. These parameters are but not limited to: soil density, pile length, pile spacing, raft geometry, and piles installation technique. This study is to examine experimentally the effect of sand density and pile installation techniques on the load sharing mechanism. Experimentally, tests were conducted on a square rigid raft with a single pile in sand under three different soil densities; 30%, 45%, and 60%. The experimental results are used to determine the pile and the raft shares in non-displacement and displacement piled raft systems. The results of this study reveal that soil density changes the load sharing of displacement piled raft; the pile share increases in higher soil density. However, this is not the case in non-displacement piled raft and load sharing is independent of soil density in working loads.IntroductionThe piled raft foundation is a combination of shallow and deep foundation which transfers the superstructure load to the soil by a complex soilstructure interaction. The interacting mechanism among foundation elements and their surrounding soil is illustrated schematically in Figure 1 and could be classified into two categories: (1) pile-soil-pile and (2) pile-soil-raft. The pile-soil-pile interaction is the same as the free standing pile group and is a function of pile spacing and pile installation method. Pile-soil-raft interaction, which only involves in piled raft foundation design, could be affected by: the length, spacing, and roughness of the pile, the rigidity and dimension of the cap, soil condition, and the pile installation method. Pile-soil-raft interaction could have favourable and unfavourable effects on bearing capacity and settlement, respectively. The pressure between the cap and the soil favourably increases the horizontal stress on the pile shaft and consequently increase the shaft resistance. Whereas, this pressure induces negative skin friction on the piles which increases the settlement. The pile-soil-raft interaction mainly controls the load sharing mechanism of piled raft foundation when pile spacing (S) is more than 3.5dp."

Jan 1, 2017

By Eric P. Bregman, Franklin M. Grynkewicz, John E. Regan

"As part of an on-going effort to improve water quality and reduce discharge into Boston Harbor, the Massachusetts Water Resources Authority (MWRA) East Boston Branch Sewer Relief Project was designed under a Federal mandate from the United States Environmental Protection Agency (EPA) to upgrade the aging sewer system, increase system storage and greatly reduce the volume of combined sewer overflows into the Harbor. The project scope of work includes the installation of over 2 miles (11,800 linear feet) of 36-inch and 66-inch diameter sewer relief piping, twenty (20) temporary shafts and an approximate 100 foot open cut section, located within the densely populated neighborhood of East Boston, Massachusetts. This area is a former marshland backfilled in the early to mid 1800’s where busy commercial streets co-mingle with thickly settled residential houses.The subsurface conditions present within Boston’s complex geology include the presence of subsurface contamination as well as complex networks of underground utilities. Additional site limitations included low headroom, noise, and traffic restrictions. Together these limitations required the design of individual earth support systems, tailored for each shaft location. Moreover, challenging subsurface conditions identified during construction required design modifications to minimize cost and schedule impacts related to construction dewatering, treatment of contaminated groundwater, internal bracing, and utility relocations.This paper provides a case history of the Geo-structural design and performance of various earth support techniques utilized to construct jacking and receiving shafts designed to launch and receive two (2) micro-tunnel boring machines (MTBM) and to support the construction of new deep shaft structures in an urban coastal area."

Jan 1, 2017

By J. Gniel, L. King, C. Gaudin, C. O’Loughlin

"This paper presents some recent advancements in centrifuge modelling, which enable the installation of displacement piles to be performed in-flight while measuring ground responses. Details and results are provided from a series of experiments where 21 full-displacement piles were installed into a sample of consolidated kaolin clay at 40g. The piles were pushed into the sample at a constant rate of penetration, with installation reaction loads and pore pressures measured. Insight into the installation effects of the full-displacement piles was obtained by undertaking in-situ testing pre- and postinstallation of piles. The findings show that centrifuge testing has the potential to play an important role in furthering the current understanding of displacement pile behaviour and installation effects.INTRODUCTIONDisplacement piles and displacement ground improvement columns cause soil to undergo significant distortion and shearing during installation, which alters the soil properties. It is essential to consider these changes in soil properties to estimate the behaviour of pile foundations with higher degree of accuracy. However, the installation effects of displacement piles are widely considered as one of the most difficult geotechnical mechanisms to model, both analytically and numerically, and experimental data is needed to advance the current state of knowledge.Theories, analytical and semi-analytical, have been developed to describe the displacement pile installation process. Randolph et al. (1979) applied the cylindrical Cavity Expansion Method (CEM) to model the installation of a displacement pile in a fine grained cohesive soil. However, cylindrical CEM only considers the field variables in radial coordinates, and hence the soil-pile interface can only be modelled as a frictionless material. Baligh (1985) introduced the Strain Path Method (SPM), which assumes soil flows around the tip of a displacement pile. SPM was shown to model the stress and strain fields, particularly within close proximity to the pile, more accurately compared to the cylindrical CEM. While these methods account for the installation effects of a displacement pile and can be used to estimate a resulting ultimate bearing capacity, they are unable to describe the load-settlement behaviour of such piles. With the added complexity of group effects, existing analytical methods do not provide a means to accurately calculate the ground response to the installation of a group of displacement piles in a cohesive soil.The advancement of computational power, numerical techniques and constitutive models has improved the accuracy of numerical analysis, particularly in regard to modelling pile installation. However, even with advanced techniques, Finite Element Method (FEM) suffers a number of disadvantages due to the large deformations, which results in mesh distortion and tangling. Mesh-free methods such as Discrete Element Method (DEM), Smoothed Particle Hydrodynamics (SPH) and Material Point Method (MPM) are the next generation of computational techniques that are able to deal with large deformation problems. However, these advanced techniques are computationally expensive, complex and yet to be incorporated into commercial packages. Such methods are considered to still be in the development stage and are yet to provide a complete solution to pile installation problems."

Jan 1, 1900

By Michael Oakland

This paper will discuss the design analysis of sheet pile cofferdams for static and dynamic blast loads. Following construction of the new Willis Avenue Bridge across the East River between Brooklyn and Manhattan, in-river piers No. 9 and No. 10 from the former bridge were demolished, partially by explosive charges. The blast at Pier 10 was conducted first and though the demolition charge was relatively small, it gave confidence that the sheeting could be designed to resist the blast load. This paper primarily summarizes our analysis and performance of a sheet pile cofferdam at Pier 9 used to withstand the larger blast loads, contain the blast debris, and allow excavation of the pier below the existing river bed mudline. The program NLFlex was used to predict stresses and deformations of the cofferdams under dynamic blast loads, using simplified equations to estimate the underwater blast pressures. Specifically, the analysis focused on the stresses in the struts, waler beam, sheet pile interlocks and connection of the sheeting to the waler beam. Design included allowing plastic deformations and limited rupture of the sheet pile interlocks under the blast loading. Comparisons are made between stresses assessed by the dynamic finite element modeling and empirical relationships used within the industry. The performance of the system after the actual blast is discussed as well as details of the performance of welded vs. bolted connections within the system.

By John P. Turner, Benjamin J. Turner

"Non-destructive testing and evaluation (NDT/NDE) methods have become standard tools as part of the post-construction quality assurance of drilled shaft foundations. In responding to anomalies, foundation designers, owners, and contractors face a number of choices, including: (i) acceptance of a shaft with known anomalies, (ii) further investigations of integrity (e.g., concrete coring), (iii) repair schemes, and (iv) reject and replace. To assist in selecting the best option, analyses are often performed that involve assessing the structural performance of reinforced concrete shafts that may include defective concrete or voids. Currently, the analytical tools for predicting the flexural strength and stiffness of drilled shafts with defective concrete located in discrete regions of the cross section are limited. This paper presents a robust moment-curvature analysis tool for drilled shafts based on the fiber-element discretization method. The tool allows for consideration of anomalous or defective concrete regions in the shape and location that they are believed to exist in the shaft while considering explicitly the nonlinear material behavior of the intact regions based on expected material properties. A case study is used to illustrate the practical application of the analysis to drilled shaft projects.INTRODUCTIONImperfections such as defective concrete or accidental eccentricity of reinforcing cages are an inherent part of the drilled shaft construction process that will occur occasionally even when construction best-practices are followed. Petek et al. (2002), O’Neill and Sarhan (2004), Poulos (2005), and others have described the effects that construction defects can have on the axial and lateral performance of drilled shafts. Our industry has seen rapid progress in recent years in the development and improvement of tools for detecting drilled shaft anomalies, such as gamma-gamma and crosshole-sonic logging, sonic-echo testing, thermal integrity profiling, and even visual inspection with invasive video cameras. Nonetheless, in most cases the wealth of data from these tests is used by foundation engineers to make a fairly “black or white” decision—should the defects be repaired, or should the shaft be rejected? A third option that is not typically considered is to directly analyze the section, including anomalies, and compare the reduced strength and/or ductility to the actual project demands. This option takes full advantage of the data collected during integrity testing, and may provide a justifiable means for avoiding further construction costs and delays, whether for repair or replacement."

Jan 1, 2016

By John Mould, Gordon Chen, Michael Oakland, William McElwee

"This paper will discuss the design analysis of sheet pile cofferdams for static and dynamic blast loads. Following construction of the new Willis Avenue Bridge across the East River between Brooklyn and Manhattan, in-river piers No. 9 and No. 10 from the former bridge were demolished, partially by explosive charges. The blast at Pier 10 was conducted first and though the demolition charge was relatively small, it gave confidence that the sheeting could be designed to resist the blast load. This paper primarily summarizes our analysis and performance of a sheet pile cofferdam at Pier 9 used to withstand the larger blast loads, contain the blast debris, and allow excavation of the pier below the existing river bed mudline. The program NLFlex was used to predict stresses and deformations of the cofferdams under dynamic blast loads, using simplified equations to estimate the underwater blast pressures. Specifically, the analysis focused on the stresses in the struts, waler beam, sheet pile interlocks and connection of the sheeting to the waler beam. Design included allowing plastic deformations and limited rupture of the sheet pile interlocks under the blast loading. Comparisons are made between stresses assessed by the dynamic finite element modeling and empirical relationships used within the industry. The performance of the system after the actual blast is discussed as well as details of the performance of welded vs. bolted connections within the system. IntroductionThe Willis Avenue Bridge is one of the major access ways from the Bronx into Manhattan. The location is shown on Figure 1. The original bridge constructed in 1901 was a swing bridge over the East River. The bridge was in disrepair and outdated with regards to its ability to handle the flow of traffic resulting in numerousaccidents.In 2007, Kiewit Constructors Inc./Weeks Marine, Inc., A Joint Venture was selected to construct a replacement bridge. The $612 million project included construction of a new bridge just to the south of the original bridge. The most notable aspect of the construction was floating and lifting the new 350 ft. long swing span in place as a single piece. However, another significant challenge was using blasting to demolish two of the abandoned piers which were within the East River. The blast would be near existing structures in both Manhattan and Brooklyn and would be within 30 ft. of the new bridge."

Jan 1, 2017

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

By Mohamed A. Mansour, Ahmed M. Soliman, M. H. El-Naggar

"Grouted helical piles allow significant increase in pile capacity with low additional cost over that of conventional helical piles. They can be particularly advantageous in sites where installation disturbance can reduce or even eliminate the pile shaft resistance. For helical piles with slender shafts, a grout column offers increased buckling resistance under compression loading, and may reduce the potential settlement required to mobilize the bearing component of their plates. This paper investigates the performance of grouted helical piles installed in loose sand. Grouted helical piles were constructed and tested in a controlled laboratory environment. Helical piles with hollow pipe shaft and single helix were grouted during installation. The grout was injected into the soil under high pressure through two nozzles placed above the piles helices. The load test results showed significant improvement in the performance and load carrying capacity of the helical pile due to the formation of a cylindrical grout column along the entire shaft leading to a higher shaft resistance contribution to the total pile capacity. The results suggest that grouted helical piles with slender hollow shaft could be used to support large structural loads. INTRODUCTIONHelical piles are widely used as a deep foundation system for different engineering applications. They represent an attractive foundation option because of their cost effectiveness, ease of installation even in limited access areas, low levels of noise and vibrations, and their ability to be installed through ground water without casing. In addition, they allow immediate loading upon installation. Helical piles are installed into the ground by applying a mechanical torque to the pile head. The installation torque monitoring provides a kind of quality control during the construction of helical piles. It could be used in predicting the ultimate pile capacity using several capacity-torque correlations (Livneh and Elnaggar 2008; and Hoyt and Clemence 1989).However, helical piles installation can cause soil disturbance within the annular zone affected by the pile helices. This disturbance can introduce fissures within the pile cylindrical failure surface (Vesic 1971; Mooney el al. 1985; and Zhang 1999). Thus, the shear strength of the soil decreases along the affected zone. Bagheri and El Naggar (2013) evaluated the installation effects of helical piles in sand. They reported that as the helical blade proceeds into the ground, sand within the cylindrical path circumscribed by the helices experiences torsional and vertical shearing accompanied by sand displacement and stress changes. This process is more pronounced in the case of multi-helices and large diameter anchors. Bagheri and El Naggar (2016) evaluated the installation effects of helical piles in structured clay. They indicated that the behavior of the helical pile and its capacity are significantly affected by the degree of soil de-structuring induced by the penetration of the pile shaft and helices. In addition to the installation disturbance, helical piles have other drawbacks including; high potential settlement required to fully mobilize the bearing component of their plates, low buckling resistance of their slender shafts, and the incomplete rigidity of the coupling joints along the pile shaft that allow some lateral movement under compression loading (Vickars and Clemence 2000)."

Jan 1, 2016

By Sameh M. Khella

This paper discusses the application of deep CFA piles for the foundation of structures in different ground stratifications with a focus on the application in Queensland region. Design, construction techniques and quality measures implemented during these procedures are described. Testing methods and verification of capacity, integrity and performance of these piles are also demonstrated. Case studies for this application are presented with an appreciation of this solution within the provided project conditions of each case. Examples of successes and challenges encountered over the course of application of deep CFA in Queensland are mentioned. Limitations of the technique and less favourable situations for its implementation are also highlighted.

Nov 1, 2022

By Pawan L. Sethi

Design and construction of deep foundations and basements is increasingly becoming more complex, as the density and frequency of urban development increases. This growth brings various associated challenges in the form of design considerations and construction challenges. This paper discusses some of the challenges routinely encountered as well as some specific complications in this area, based on author’s experience gained through exposure as specialist contractor (designer), consultant and specialist consultant, along with some information on how these challenges were overcome. The paper highlights some of the key aspects of design coordination and importance of having an awareness of the overall perspective. Examples will be used to illustrate practical problems and the approaches used to respond.

Nov 1, 2022

By Terzis D. PhD, Katterbach M.

While awareness around the environmental impact of existing grout materials and chemical binders is increasing rapidly, biotechnologies are growing traction as sustainable alternatives in groundwork operations. Herein we present the principles and application methods of bio-grouting. The term is used to describe a system which is based on soil, groundwater or marine enzymes which are able to catalyze the production of calcite replicating a natural phenomenon. The system’s end result are mineral crystalline bridges which act as binders to improve the geotechnical properties of soils. This paper presents a comprehensive description of bio-grouts, their underlaying mechanisms contributing to mineralization as well as environmental considerations. With their water-like rheology, bio-grouts have a wide application range and are minimally invasive, requiring only very limited injection pressures. The equipment is the same as that used in conventional cement grouting, and the reactant components are worldwide available or easily suppliable, which explains why bio-grouting has nowadays become a valuable and sustainable alternative towards efficient soil treatment. Recent developments in the last years have allowed to further increase the applicability and efficiency of bio-grouts to ultimately bridge the gap between research and practice. A case study is illustrated in this paper showing the successful implementation of bio-grout for the stabilization of weakly cemented sandstone to safeguard an adjacent road segment in Switzerland

May 1, 2022

By Frank J. Purcell

“Down The Hole” (DTH) hammer drilling is often necessary to advance the casing during pile construction where the test bores have determined difficult drilling conditions with obstructions such as boulders, cobble and glacial till. The use of compressed air to operate DTH hammers in foundation drilling has been a contentious point in many regions of the world due to its potential to disturb the ground around the pile being constructed. There are many examples of damage to adjacent building foundations where compressed air exiting the pile being drilled disturbed the subsurface around the building’s existing piles. This paper looks at the use of compressed air in DTH hammer foundation drilling and the move towards controlling the exhausted air to avoid over drilling the pile, causing potential damage to nearby piles. Simulated models of air flow penetration into the soil of different configurations of drill bits are discussed to highlight design changes employed to better control the air during the drilling process. A case study of the construction of a water-tight pipe pile wall for a building’s underground parking structure is studied to demonstrate the potential of DTH hammer foundation drilling where the air is fully controlled.

Nov 1, 2022

By Andrew Moran, William H. Walton, Matthew D. Emrick, Mary C. Nodine

"A rapidly growing company in the northern US needed a large auditorium built into a dolomite bedrock hillside. The structure required an 80-foot-deep earth retention system independent of the auditorium foundation and superstructure. Allowable wall movements were limited to less than two inches. A 60-foot-tall permanent shotcreted soil and rock nail wall was designed for excavation support. The soil and rock nail wall utilized both active (post-tensioned) and passive nails, with capacities and installation angles optimized to address varying soil and rock conditions and to support heavy surcharges. The wall was configured with three two-foot-wide benches to facilitate controlled blasting and removal of more than two million cubic yards of soil, limestone and dolomite bedrock, and featured a permanent cast-in-place concrete face and a robust waterproofing and drainage system. A 20-foot-high reinforced concrete retaining wall was required at the top of the soil and rock nail wall to raise grades, resulting in a large surcharge.Design of the soil and rock nail wall was initiated less than three months before the start of construction, requiring expedited geotechnical explorations, analyses, design, and construction that would occur simultaneously. Design changes were made to address the discovery of a weak clay residuum seam at depth running along the base of the excavation, as well as significant changes to the building footprint made after the start of construction. Extensive performance monitoring was conducted during construction to measure vibrations and movements.Introduction and Project BackgroundA fast-growing company in the northern United States had a need for 600,000 square foot, 11,000 seat auditorium as part of its campus expansion. The auditorium was built underground, into a hillside to preserve the views of rolling terrain and farmland beyond. It featured a green roof and rockwork facing that mimicked regional geologic formations. The sixstory building required up to 80 feet of earth retention, including 60 feet of excavation beneath existing grades.As concepts for the project evolved, it became apparent that due to the geologic conditions, space limitations on site and the depth of cut required, a standard counterfort wall system would not be feasible. With groundbreaking for the building three months away, Thornton Tomasetti (structural engineer) engaged GEI Consultants, Inc. (wall design engineer) to design a 1,600-foot-long permanent soil and rock nail wall to support the excavation. The wall design engineer implemented a geotechnical exploration program immediately and began the design process, coordinating closely with Nicholson Construction (specialty"

Jan 1, 2017

By Clifford Taylor, Alexander Zöhrer

"The execution of deep basement excavations under narrow conditions is one of the most challenging tasks in geotechnics. The vicinity of neighbouring buildings, roads, and underground structures such as sewers or power lines, quite often prohibits the application of standard solutions. In addition, legal considerations in the use of adjacent properties is becoming increasingly difficult. This paper will present some innovative approaches to overcome the above-mentioned challenges based on several case studies from central Europe. For every project the design approach as well as the techniques used for execution will be explained, detailing both the advantages and the limitations of the applications. One case study shows a deep basement excavation (approx. 17m) in the centre of Prague, Czech Republic. This project featured many challenging boundary conditions (narrow construction area, high ground water table, jet grouting column embedment into bedrock, constraints regarding use of ground anchors due to property rights, etc). The realisation of the complex design is described and illustrated in detail. Other case studies will show the combined application of bored piles with jet grouting and also explain the design of vertical prestressed anchors for retaining walls.INTRODUCTIONThe development of urban areas has always presented challenges, from access for equipment and materials to the rectification of existing foundations in unknown condition. Compounding these is the increasingly stringent requirements to retain, maintain and reduce impact on culturally and historically significant structures. As available space is becoming more limited, optimisation of real estate has resulted in buildings getting higher and their basements deeper below ground. Two or more basement levels are quite common, with typical excavation depths ranging from 5 to more than 10m. Additionally, we are faced with neighbouring buildings that are equally high, deep and massive. These buildings directly adjacent the retaining structure require underpinning to limit settlement, and in cases where they are within just a few meters, this building mass generates additional earth pressure for the retaining wall to support, resulting in complex loading cases.This paper highlights several common challenges and explores the measures implemented to overcome them. The challenges and examples of either design based solutions or practical applications will focus on the following topics – the limitations of conventional geotechnical construction methods, overcoming challenging geology and the requirement for watertight basement constructions."

Jan 1, 1900