Search Documents

By Scott Dodds

"The Oxford Hydroelectric Station was a unique project that incorporated a variety of dam strengthening methods to stabilize the facility in order to meet the standards required by Federal Energy Regulatory Commission (FERC). The dam stability and Probable Maximum Flood (PMF) remediation work consisted of (1) construction of a new emergency spillway; (2) installation of 75 high capacity rock anchors; (3) construction of an anchored concrete powerhouse buttress; (4) construction of cast-in-place and sheetpile flood walls; and (5) design and construction of a permanent soil nail wall. INTRODUCTIONThe Oxford Hydroelectric Station is one of 11 hydroelectric facilities owned and operated by Duke Power along the Catawba/Wateree River. The Catawba River originates in the foothills of the Appalachian Mountains just west of Morganton, North Carolina. The river flows east out of the mountains and, at a point just below the Oxford Dam, the Catawba River turns and heads southeast. The Catawba River continues to flow southeast past Charlotte and into South Carolina where it eventually becomes the Wateree River. The Wateree River eventually flows in to the Atlantic Ocean.Located a few miles east of Hickory, North Carolina, the Oxford Dam and Hydroelectric facility is in the upper reach of the Catawba River. Oxford Dam creates the third impoundment along the river known as Lake Hickory. Lake Hickory is well known locally for providing many outdoor activities such as boating, jet skiing, canoeing and fishing. The dam and powerhouse were put into operation in the spring of 1928.Key features of the dam include a short embankment section on the south end of the structure, a 391-foot (119m) long south bulkhead and powerhouse, 540-foot (165m) long gated spillway section and a 235-foot (71.6m) long north bulkhead. The maximum height of the dam is approximately 100-feet (30m) from the crest to the dam/rock interface. (See Figure 1).The work associated with this project is the result of licensing requirements of the Federal Energy Regulatory Commission (FERC) which mandates that all hydroelectric facilities have the capacity to safely discharge runoff created by a critical rainfall event defined as the probable maximum flood (PMF). Duke Power, a division of Duke Energy (DUKE) submitted an initial PMF report in 1992 which indicated that at the Oxford Dam would be overtopped by approximately 10-feet of water during the modeled PMF event. Given the duration and depth of the overtopping, significant damage to the facility and a possible breach could result. Therefore, modifications to the existing facility were necessary to satisfy the report of the PMF model."

Jan 1, 2005

By Gordon Chen

As part of a value engineering envisioned by East Coast Slurry, Weidlinger Associates, Inc. designed a unique elliptical slurry wall cofferdam for construction of the 65 ft. deep MWRA North Dorchester Pump Station. A conventional rectangle cofferdam with multiple levels of bracing would have been time consuming and costly and imposed a significant obstruction to the pump station construction. A circular slurry wall, while eliminating the bracings, conflicted with adjacent structures and required excessive backfilling around the final pump station structure. The ellipse shaped cofferdam fit the needs of the project well; however, it created a significant design challenge without the use of bracings. Unlike a circular cofferdam which primarily only has hoop stresses, the ellipse still has to be designed for horizontal bending moments in each panel because of the non-axial symmetric conditions. The more eccentric the cofferdam shape; the higher the horizontal bending. The challenge was to develop a three dimensional finite element model that could analyze both the hoop stresses and horizontal bending stresses above and below the bottom of excavation induced by soil and water pressure and unbalanced construction surcharge loads. This paper discusses the techniques used to model the soils and structure interactions and results of stresses on this challenging unbraced configuration.

Jan 1, 2010

By Joseph A. Sopko

There has been a trend in recent years in performing the initial formation freezing using liquid nitrogen (LIN) and then converting the system to circulating refrigerated brine. While proponents of this method state it decreases freezing time, it can also be considered an alternative to inadequate refrigeration capacity. This method was used on several small projects in the 1980s. Problems such as broken pipes, frozen brine, and unsafe work conditions caused contractors to re-think the method. This paper discusses these problems and also presents work schedules showing no schedule reduction. In fact, this method can lead to longer time as well as significantly higher costs. BACKGROUND Ground freezing as a method to provide groundwater control and temporary earth support for excavations is completed using a relatively simple process: drilling and installing refrigeration pipes around the perimeter of the excavation and introducing a coolant into these pipes. The coolant extracts heat from the ground, converting the pore water to ice and forming a strong, impermeable material. A typical ground freezing system is illustrated in Fig. 1. SYSTEMS There are two basic types of coolant systems: circulating and direct expansion. The circulating coolant system is made of two separate, closed systems. The medium circulating is the secondary coolant. It is cooled at a central refrigeration plant, circulated through the pipes, and warms as it extracts heat from the ground. It then circulates back to the plant where it is cooled. This coolant is chilled in a heat exchanger by the primary refrigeration system where a compressor system is charged with a refrigeration gas. The heat is ultimately extracted from the ground and expelled into the atmosphere by an evaporative condenser. Secondary coolants are usually a brine or glycol chemical while the primary refrigeration gas is anhydrous ammonia or another commercially available gas.

Jan 1, 2019

By Lenin T., Madhav M. R., Padmavathi V.

Use of PVDs and preloading on the ground can significantly reduce the time taken for ground to consolidate. Many soils in situ are lightly overconsolidated, with overconsolidation ratios (OCR) ranging from 1.0 to 2.0 due to various reasons such as glaciation, ground water level fluctuation, aging, cyclic loading, creep, erosion, cementation, etc. The effects of overconsolidation ratio are analysed in this study. Compression index and consolidation coefficient are important parameters in determining time – settlement response of soft soils under preloading and with PVDs. These parameters are typically estimated using oedometer tests on samples, with the assumption that the results represent the entire deposit. The in-situ time-settlement plots at different depths are used in the back analysis for estimating compressibility and consolidation parameters of in situ ground, resulting in more representative values that reflect the deposit's overall behavior. From observed time versus settlements plots, variations of compression index and coefficient of consolidation with depth of a deposit are presented. Estimation of compression index with depth is possible based on different OCR values as shown in this study. Barron (1948), Asaoka methods are used to estimate the coefficient of consolidation with flow in the radial direction.

Sep 1, 2022

By Daniel A. Thome, Robert C. Janke

"Installation of permanent soil nails through distressed mechanically stabilized earth retaining walls is a cost effective and aesthetically pleasing solution when using the appropriate equipment and drilling methods for installation. A forensic investigation was performed on an existing mechanically stabilized earth retaining wall to determine the possible causes for the excessive horizontal displacements and visual structural flaws found along a portion of the wall. Reports concluded that the visual shifting was due to a number of factors including improper drainage in the vicinity of the wall and unsuitable compaction of the backfill material. Conceptual designs were proposed to the owner and the installation of permanent soil nails through the existing precast panels was determined to be the most practical solution. A total of ninety-three permanent soil nails were installed to lengths of up to 40 feet (12 m) through sand backfill and silty day fill using a hydraulic rotary percussion drill attached to a tract mounted excavator.IntroductionThe Illinois State Toll Highway Authority awarded Contract RR-03-5144 in the summer of 2004. Construction work for the project consisted of the rehabilitation of two existing concrete culverts and approximately 100 linear feet (31 m) of mechanically stabilized earth (MSE) retaining wall. The retaining wall is located below the southbound lanes of the Tri-State Tollway near the intersection of Federal Highway 41 in Wadsworth, Illinois as shown in Figure 1.Reports were prepared by Applied Technologies in cooperation with Giles Engineering Associates to determine the condition of the MSE wall and recommended conceptual designs to extend the service life of the wall.Nicholson Construction Company (Nicholson) wasselected as the design-build geotechnical subcontractor to install the recommended permanent soil nails through the existing precast concrete panels of the MSE wall. Rehabilitation of the wall involved the installation of ninety-three permanent soil nails through the existing wall, along with soil nail verification tests and proof tests on production nails."

Jan 1, 2005

By Federico Pagliacci

"Many existing dams are subject to underwater seepage due to subsoil conditions, like deep alluvial deposits or pervious rocks or karst. Remedial works are necessary in order to install new cut-off walls to stop the water flow. In some cases the cut-off walls have to be executed at depths never reached so far, and difficult to reach with traditional foundation techniques. In many cases the Hydromill technology proved to be the best system to overpass rocky layers and ensure the required verticality. The maximum depth reached by the industry was in the range of 120-150 meters. This article describes the test performed to excavate and cast in place a 3.2x1.5 m panel to a depth of 250 m. The article will also describe the stratigraphy of the site down to 250 meters, as well as the technique adopted to achieve the said depth with deviations from verticality of 30 cm along the longitudinal axis (0.12%) and 20 cm along the transverse axis (0.10%), measured at the bottom of the excavation. The concreting of the panel, for about 1,100 m³, with plastic concrete in the lower portion and conventional concrete in the upper portion will be illustrated. Finally, the tests performed during the excavation and after concrete casting will be also described, with special attention to the continuous directional core drilling that was performed along the whole length of the panel to verify the results of the deviation from verticality, through the onboard instruments, and to control the quality of concrete at a depth never reached before. IntroductionMany existing dams are subject to underwater seepage due to subsoil conditions, like deep alluvial deposits or caves and cavities or acid solutions in the bedrock formations.Conventional remedial works generally consist in the construction of an additional cut-off wall throughout the dam body and the subsoil, in most cases being deeper than the original one. Today, many examples of successful remedial cut-off walls allow the engineers to design the most suitable solution according to the dam and subsoil characteristics and nature.The real difficulty stems from the depth at which the new cut-off wall has to be socketed in competent rock or soil, so as to eliminate underwater seepage. The maximum depth ever achieved with a cut-off wall is 122.5 m for the remedial work of Mud Mountain Dam, Washington, USA, in 1988-1990. This 0.85-1.0 m thick cut-off wall was realized by means of a Hydromill, by excavating single 2.8 m-wide secant panels."

Jan 1, 2017

By Federico Pagliacci

Continuous Flight Auger (CFA) technique represents an important technological advance in the construction of piles in soft soils. The possibility of excavation under the water table with no need for drilling fluids, along with high productivity, have resulted in this technique?s becoming widespread in many countries. However, CFA technology has limitations because of its difficulty in penetrating hard layers and cross strata with cobbles and boulders. In these situations, pile verticality may be an additional problem. The Cased Augered Pile (CAP) technique consists of penetrating the soil with an auger housed in a casing. Two independent rotary heads sliding along the rig mast operate the auger and the casing. By adjusting the height of the casing shoe and auger bit according to soil type, it is possible to drill piles in very severe conditions - in the presence of cobbles and boulders - and to socket the pile into the rock. The use of a steel casing enables improved pile verticality. Therefore, the CAP technique is also used to construct secant piles to be used as diaphragm walls. The limitations of this technology are the depth, usually no more than 27 m (88 feet), and the size of the rig that supports the drilling tool, no less than 70 t (77 short tons) in working conditions. This paper illustrates CAP technology, the drilling system, and the characteristics of concrete and steel reinforcement and offers a case study of the Palermo-Carini second railway line, which used CAP to construct the new 30 km (18.6 mi) railway line, 20 km (12.4 mi) of which passes through the very congested downtown area of Palermo. More than 300,000 m (186.4 mi) of piles have been drilled in dense calcarenite formations with unconfined compressive strength of 15-25 MPa (2,200-3,600 lb/inch2), soft clay, and silt formations.

By Federico Pagliacci

Continuous Flight Auger (CFA) technique represents an important technological advance in the construction of piles in soft soils. The possibility of excavation under the water table with no need for drilling fluids, along with high productivity, have resulted in this technique’s becoming widespread in many countries. However, CFA technology has limitations because of its difficulty in penetrating hard layers and cross strata with cobbles and boulders. In these situations, pile verticality may be an additional problem. The Cased Augered Pile (CAP) technique consists of penetrating the soil with an auger housed in a casing. Two independent rotary heads sliding along the rig mast operate the auger and the casing. By adjusting the height of the casing shoe and auger bit according to soil type, it is possible to drill piles in very severe conditions - in the presence of cobbles and boulders - and to socket the pile into the rock. The use of a steel casing enables improved pile verticality. Therefore, the CAP technique is also used to construct secant piles to be used as diaphragm walls. The limitations of this technology are the depth, usually no more than 27 m (88 feet), and the size of the rig that supports the drilling tool, no less than 70 t (77 short tons) in working conditions. This paper illustrates CAP technology, the drilling system, and the characteristics of concrete and steel reinforcement and offers a case study of the Palermo-Carini second railway line, which used CAP to construct the new 30 km (18.6 mi) railway line, 20 km (12.4 mi) of which passes through the very congested downtown area of Palermo. More than 300,000 m (186.4 mi) of piles have been drilled in dense calcarenite formations with unconfined compressive strength of 15-25 MPa (2,200-3,600 lb/inch2), soft clay,

Jan 1, 2017

By Joseph A. Sopko

The first documented procedures for designing frozen earth structures are over 50 years old, implemented long before the introduction of the Finite Element Method (FEM). Since that time, the development of three-dimensional models has made the traditional and often over-conservative methods relatively obsolete. This paper discusses a new approach that is largely dependent on the analysis of internal stresses with the frozen structure and comparison to frozen soil laboratory tests. A specific design process is discussed related to initial field investigation, laboratory testing, structural and thermal analysis, and performance monitoring. The design results are compared to case histories in the field that verify the procedure. BACKGROUND One of the first documented methods to designing frozen earth retaining structures was by Sangar (1968). Methodical refinements were published by (Harris 1995) and published by the International Symposium on Ground Freezing in 2002 (Andersland et al. 1991). The structural design or thickness of the frozen mass was based on the unconfined compressive strength of the frozen soils. Two simple equations for determining the thickness of a frozen shaft are shown in Fig. 1 and the first two equations below.

Jan 1, 2019

By Michel Bustamante

The Arbre viaduct, 200 metres long, is the most important structure on the Belgian portion of the High Speed Train line between Paris and Brussels. The particular geotechnical conditions of the soil with carboniferous limestone affected by karstic phenomena, has prompted the designer to found the viaduct on systems of high capacity vertical and batter micropiles. The design of the working micropiles was validated by full scale tests performed on instrumented micropiles. The size of the structure and the deformation criteria to be met when HS trains are crossing the viaduct, together with the lack of references for such innovative structure, called for monitoring the movements of the piers as soon as the link was open to traffic. The authors report on the results of loading tests on micropiles and the results of settlement structure monitoring for a period of 4 years. Settlement of the foundation is estimated taking into account the group effect.

Jan 1, 2002

By Andreas Andenæs, Arne Schram Simonsen

"AbstractThe Tresfjord bridge is with its variety in foundation concepts and difficult soil conditions one of the most geotechnically challenging projects in Norway at the time. The project comprises design of large concrete caissons, steel core piles through large rock fills, and closed end steel pipe piles in up to 40m water depth driven in very hard moraine. Test piling has also been conducted to check feasibility of the concept, and PDA measurements have been used to verify sufficient capacity of piles. FactsThe Tresfjord bridge is part of the new export road from Ålesund to Åndalsnes on the North-West coast of Norway built by the Norwegian Road Administration. The bridge will reduce travel time with about 30 min between the cities, see Figure 1. The bridge is planned to open summer 2015.The Bridge crosses the Tresfjord and will be 1290 m long. The bridge is built as a free cantilever bridge and will be resting on a total of 20 nos. of foundations, where two are abutments resting on steel core piles, three are casted directly on bed rock and 13 are foundations resting on steel pipe piles. The last two foundations holding the main span will be concrete caissons resting on bed rock and moraine. Figure 2 shows a 3D model of how the finished bridge will look. Multiconsult AS is responsible for design and pile supervision , while the Joint-Venture Bilfinger-Tresfjordbridge ANS is responsible contractor.Soil ConditionsPercussion soundings and sampling together with coring have been performed in the individual foundations using a small geotechnical equipped vessel. Acoustic and refraction seismic profiling have also been carried out to tie in the layers between the boreholes.The soil conditions are varying over the length, but are in general dominated by a soft top layer (2-4 m) of sediments over very hard moraine with occasionally large boulders. Piles in the two foundations closest to shore on the western side of the bridge are piled to bed rock with penetrations up to about 27 m in soil.Water depth varies from about 10 to 40 m for the piled foundations. Figure 3 show how the topography of the seabed varies over the bridges length."

Jan 1, 2014

By Nabil F. Ismael, Mohamed El Deeb

"The behavior of laterally loaded step tapered bored piles in calcareous sand was examined by field tests. Lateral load tests were carried out on straight and step tapered bored piles 5.3 m long embedded 5 m below ground level. All piles were installed by augering. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles have a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads. Test results indicate non linear response and substantial increase in lateral capacity and decrease of deflection for the step tapered piles compared with the 0.2 m diameter straight shaft piles. However, beyond a depth of 40% of the pile length, the strengthening of the pile section by enlargement of its diameter had little effect on the lateral capacity and the deflection of step tapered bored piles.IntroductionFor many structures on pile foundations the ultimate capacity under lateral loads is important and may be the controlling factor in foundation design. Examples include transmission tower foundations and fender piles at sea port facilities. Increasing loads on these structures has resulted in piles of large diameter and depth at a significantly higher cost.In this work, the use of step tapered bored piles with a larger diameter along the upper segment of the piles is examined by field testing and analysis on single piles in calcareous desert sands. Lateral load tests were carried out on straight and step tapered piles 5.3 m long embedded 5 m below ground level. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles had a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads for step tapered bored piles."

Jan 1, 2005

By Onur Guvener, Kalaiarasi Vembu, C. Vipulanandan

"Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.INTRODUCTIONAugered cast-in-place piles (ACIP) are drilled foundation installed by drilling a hole with a continuous flight auger to a predetermined depth. Non-displacement Augered Cast-in-Place (ACIP) piles are increasingly used for supporting building, bridges, sound barrier walls and many other structures around the world. In an ACIP pile, depending on the soil type and rate of the auger advance, ground stresses are maintained near the value that existed before construction by using a continuous flight auger, which is never withdrawn until the cementitious material (fluid Portland cement grout) is placed by pumping the grout beneath the withdrawing auger under pressure through the hollow stem of the auger (Vipulanandan, 2005). ACIP piles are typically installed with diameters ranging from 0.3 to 1.0 m and lengths up to 30 m (Brown, 2005) although longer lengths have occasionally been installed. Comparing to the drilled shafts and driven piles of equivalent size ACIP piles can be installed more rapidly with fewer disturbances to the surroundings in favorable geological conditions. Hence the installation procedure and the quality of material used in the construction have significant effects on the behavior of ACIP piles (Vipulanandan, et al. 2007). In this paper construction quality control technique for ACIP piles was investigated. Load displacement and load transfer behavior of pile in compression and tension in hard clay was also studied. The development of side resistance in compression and tension for the load test piles and the reaction pile were also investigated."

Jan 1, 2017

By Anthony T. C. Goh, Zhiye Zhao, Laddu B. Jayasinghe, Hongyuan Zhou, Yilin Gui

"Ground vibrations from blasting are undesirable and they are very short in duration with high principal frequencies and high amplitude. Structural response to that kind of excitations may differ significantly from that generated by lower-frequency earthquake vibrations. In practice, the damage to nearby structures to generated ground vibrations has been controlled by various codes and regulations available. However, the existing vibrations limits are not always applicable, as they depend on the geological conditions of the site and the dynamic characteristics of the structure. This paper investigated the influence of the rock-soil interface on the response of pile foundation to ground-borne vibration from rock blasting, through numerical simulations using finite element software LS-DYNA. It is found that the slope of the rock-soil interface greatly influences the location of damage and the extent of damage on the pile. The bottom of the pile is subjected to a larger blast pressure and stresses are highly concentrated at the pile bottom. Thus, the pile bottom can fail in shear before it reaches its plastic moment capacity.INTRODUCTIONDrilling and blasting is the widely accepted method to large-scale rock breaking activities in civil engineering constructions due to its cost effectiveness, higher efficiency and ability to break hard rock. However, ground vibrations from blasting are undesirable and it can cause damage to nearby structures. In practice, the damage to nearby structures to generated ground vibrations has been controlled by various codes and regulations available. The existing vibration limits are not always applicable, as they depend on the geological conditions of the site and dynamic characteristics of the structure.Pile foundations are commonly used as foundations of high-rise buildings and bridges to transfer the heavy loads from the superstructure above through weak compressible soil strata into deeper, competent soil layers which have adequate capacity to carry these loads. In engineering practice, many piles are normally designed to carry mainly vertical loads and very little lateral loads, as typically the vertical loads (the gravity) are significantly larger than the horizontal loads such as wind loading. However, in recent years, there have been a number of reported case studies of translational soil movements that have induced stresses and bending moments that have damaged pile foundations and in some cases resulted in collapse of the superstructure. Typical lateral load include nearby construction activities such as an excavation for a basement or slope, the construction of a road embankment or a tunnel, as well as earthquakes (Abdoun 1997; Goh et al. 1997; 2003; Chen et al. 1999; Dobry et al. 2003; Boulanger et al. 2007; Black et al. 2007)."

Jan 1, 1900

By Chunli Wei, Mark Jen, Xiaojun Wang

"After more than 85 years of service, a critical link between New York and New Jersey, the Goethals Bridge over the Arthur Kill waterway, is being replaced with two new parallel bridges. Each bridge includes 1,650 feet long signature steel composite cable-stayed bridge, a 2,789 feet long New York approach and a 1,889 feet long New Jersey approach. The superstructure of each approach is supported on a series of two-column concrete piers and each column is supported on a single large diameter drilled shaft varying from 4.5 to 9 feet in diameter and anchored 45 feet below ground into the underlying rock.A performance-based methodology was followed for the strength and extreme event limit states design of the drilled shaft foundations. The design for seismic loads has been performed using the AASHTO Guide Specifications for LRFD Seismic Bridge Design. For all strength and service loads, the AASHTO LRFD Bridge Design Specifications were used. Since the longitudinal and confinement requirements in the two specifications vary, the minimum longitudinal reinforcement was based on the more stringent requirements of the two codes. A design example is presented to illustrate the methodology in bridge deep foundation design using nonlinear time-history global analysis results with soil-pile interaction represented by sets of horizontal and vertical nonlinear soil springs along the drilled shaft, based on the soil and rock properties from the boreholes test results. In this paper the design methodology implements strain limits related to earthquake intensities and damage levels to calculate the capacity using XTRACT analysis, which aids designers to adopt applicable provisions that meet specific design requirements.INTRODUCTIONAfter more than 85 years of service, a critical link between New York and New Jersey, the Goethals Bridge over the Arthur Kill waterway, is being replaced with two new parallel bridges designed to carry vehicular traffic and a future mass transit corridor. They include two 1,650 feet long signature steel composite cablestayed bridges with 260 feet tall V-shaped concrete gateway towers (Figure 1). The approaches consist of continuous pre-stressed concrete girders. The New York approach is a single structure consisting of 18 continuous spans, sloping at 4% for a total length of 2,789 feet without expansion joints. Similarly, the longest continuous portion on the New Jersey approach, with a similar slope, consists of 11 spans for a total length of 1,889 feet without expansion joints. The superstructure of each approach is supported on a series of two-column concrete piers that vary in height from 121.3 feet near the cable-stayed bridges to 11.8 feet near the abutments. Each column is supported on a single large diameter drilled shaft varying from 4.5 to 9 feet in diameter and anchored 45 feet below ground into the underlying rock."

Jan 1, 2016

By Patrick J. Hannigan, Seth Robertson, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (―TLBT‖) and the conventional Bi-Directional Load Test (―BDLT‖) are full-scale static load test methods. In both methods, the test loads are applied bi-directionally to the deep foundation. The advantages of the conventional BDLT have been well established for cost efficient static load testing of deep foundations, particularly for large diameter, high-capacity drilled foundations. A conventional BDLT applies the bi-directional test loads using an embedded jack and bearing plates. The TLBT method also applies the bi-directional test load to embedded bearing plates but does so using reusable high-strength threaded bars attached to an above-grade hydraulic jack and load transfer assembly. The new TLBT method is well suited for load testing shafts of a moderate diameter, length, and nominal resistance or ultimate load. TLBT advantages include economic considerations resulting from the method’s reusable load application components and constructability considerations as it readily accommodates a center concrete tremie pipe or pump line location. This paper presents comparison results from full-scale load tests performed using both bi-directional load testing methods. Adjacent 3-foot diameter by 30-foot long BDLT and TLBT shafts were tested. Details regarding subsurface conditions and test shaft construction are included for the comparison of the TLBT and BDLT results. Corresponding test data and analyses for both test shafts are presented and discussed in detail. The BDLT shaft had a maximum uni-directional load of 240 kips at upper and lower bearing plate displacements of 0.5 and -3.8 inches, respectively. The TLBT had a maximum uni-directional load of 300 kips at upper and lower bearing plate displacements of 1.0 and -5.9 inches, respectively. These results as well as the load-transfer behavior and equivalent top loading curve results from the adjacent BDLT and TLBT drilled shafts are discussed. The paper also discusses the strain gage instrumentation on the TLBT load application bars and on the embedded bearing plates.

Oct 1, 2022

By Quanchen Sun, Mohammed Z. E. B. Elsahife, Anthony Fisher, Chris Barker, Jennifer Schooling

A review of the literature shows that pile integrity is a significant concern in pile construction. Recently, a new integrity test, thermal integrity profiling (TIP,) has been put into use in foundation construction. It measures temperature changes and thermal profiles of concrete during curing. Heat generation and dissipation of early-age concrete is determined by the concrete mix, the ground conditions and the shape of concrete structure. The current data interpretation practice is primary based on experience. Anomaly detection through direct analysis of temperature profiles is currently indicative or suggestive and temperature signatures are usually similar, and numerous causes are not easily isolated. The core of the TIP testing technique, i.e. collecting detailed temperature measurements along the pile during the hydration process, is promising but a new interpretation approach is required. In this paper, a new interpretation approach has been developed in which TIP constitutes the first step. An investigative staged process is then followed to establish and assess the anomalies in the problematic regions along the pile employing the combined use of detailed finite element (FE) simulations, the actual temperature data from TIP and genetic evolution algorithms. In each stage, more details could be revealed about the anomalies being investigated including, ultimately, location, size and shape; this staged process enables practitioners to follow a riskbased approach and decide whether or not to pursue subsequent stages depending on the results they get at the end of each stage. This new approach, depending on the stages required for the analysis, will potentially avail practicing engineers of crucial test results about the quality of the pile immediately following pile construction, hence enabling repair and remedial work straight away at a lower cost.

May 1, 2022

By A. Daouadji, P. Cazes, S. Grange, L. Briançon, R. Milane

Construction in congested urban areas is often accompanied by geotechnical problems due to high loads and the impact caused by nearby buildings. For this reason, it is important to understand the behavior of the soil and the structure without forgetting the essential role of the interaction between them. Experiments, instrumentation and numerical modeling are the main methods used to study this behavior. To this end, pressure cell, strain gages, vibrating wire extensometers and optical fiber sensors are installed on the reinforcement steel of pile and raft foundations to monitor stresses and induced deformation in these elements during and after construction. A fiberglass rod extensometer is placed in the soil to help measuring the displacement due to excess loading, knowing that the pile foundations are embedded in the Rhône’s alluviums and reach the molasse, a particular and challenging soil with properties that are not yet well understood. The objective of this paper is to present the geotechnical instrumentation program carried out for the tower Silex2 in Lyon, France, and to describe the types of sensors used and their installation on site. INTRODUCTION The complexity of geotechnical structures like dams, bridges or high-rise buildings requires a sound understanding of the behavior of the soil, the structure itself and the interface. Therefore, a geotechnical instrumentation program can be essential in many ways. During the site investigation stage, it can help determine the initial conditions experienced by the soil in the field by measuring parameters such as the compressibility index or the permeability. During the construction stage, real time measurements can protect the structure from premature failure, help validate and optimize the design if needed. In addition, sensors measuring pore-water pressure, loads, deformations and settlements allow for monitoring the performance of the structure. This is called the observational method. Finally, during the operating phase, instrumentation aims to study the long-term behavior of the structure (Nicholson et al., 1999).

Jan 1, 2019

By Leena Korkiala-Tanttu, Ilkka Vähäaho, Juha Forsman, Paavo Lahdenperä, Kalle Rantala, Osmo Korhonen

"District of Arabianranta (Helsinki, Finland) has been founded on an old seabed, which was filled with miscellaneous soil materials. The subsoil consists of very low shear strength clays and organic clays (gyttjas). The soil was moving towards the sea at a rate of 1050 mm/year, because of filling on top of the soft subsoil. In the middle of 1990’s it was decided to build a residential area to Arabianranta, because it is located only 5 km away from the downtown. To inhibit the movement of soil, it was planned to build this 700 m long deep mixed column-wall barrier along the shore of Arabianranta in the years 1997–2005. A lot of instrumentation and inclinometers were analyzed and it was noticed that the column-wall remains at its place and the displacement rate inside the wall has been only 0.44.6 mm/year after construction works. Nevertheless, the displacement of soil at the landward side of the column-wall is still 1.25.1 mm/year. The soil at the seaside of the barrier is also moving towards the sea 12.922.2 mm/year. Another problem might be displacements of soil near the places where the column-wall ends (tails).1. INTRODUCTIONArabianranta district (Helsinki, Finland) has been an industrial, storage and wasteland area for a long time. Developing this area into a residential area was earlier considered too expensive, so it has been constructed during last decade. The organic clay layers (gyttjas), which have weak shear strength and high water content, were covered by various layers of fillings done in different phases. Because of the fillings, the area was not only consolidating, but also moving horizontally 1050 mm/year towards the sea due to the fact that the frictional soil under clay layers slopes towards the sea. A trial deep mixed structure was constructed in 1997 to inhibit the horizontal displacements of soil. The actual construction of the columnwall was completed in 2000-2005 with overlapping deep mixed cement columns on the seaward boundary. The barrier was built so that the horizontal movements would not risk the pile foundations at Arabianranta. The length of the barrier is about 680 m and width varies between 1220 m. There is a great amount of instrumentation near the barrier (inclinometer casings and other measuring devices). All this measuring information has been collected and analysed at 2014 to find out how this deep mixed column-wall has affected the horizontal displacements."

Jan 1, 2015

By Srijit Bandyopadhyay, Aniruddha Sengupta, G. R. Reddy, Raj Banerjee

The objective of the present endeavor is to compare the performance of a pile raft system in foundation sand subjected to lateral loads. To study the behavior of pile raft system in sand a laboratory test was conducted on small scale model foundation system. The raft and pile was modeled by square concrete foundation of 250 mm x 250 mm x 15 mm in length, breadth and thickness and 25mm diameter and 250mm long circular pile located at the center of the raft. The system was tested under static lateral loads of 6.25N, 12.5N, 18.75N and 25 N respectively resting on dry Kasai River sand. A vertical surcharge pressure of 1.5kPa (10 kg) was applied on top of the model raft for each case. The results of the model tests have been simulated by a general purpose 3-D finite element software and the model has been validated with experimental results. The moments of the pile obtained from the model tests and those predicted by the numerical analyses for all the lateral loads matches reasonably well. For matching the trend of bending moments obtained from experiments, validation with theoretical results have been done with the help of Matlock and Reese (1960) approach for a single value of lateral loading. Moreover, a parametric study has been conducted with 5mX5mX0.3m raft size with 0.5m diameter and 5 meter long pile with increasing number of piles namely 2, 5 and 9 respectively to study the response in terms of moment and lateral deformation under available earthquake loadings, like Loma Prieta (1989) and Darfield Christchurch (2010). Bending moments of piles and load deformation curves for lateral loading have been studied for each case in which it is observed that the bending moments of pile significantly reduces (around 4 times) as the number of pile is increased to two, but it decreases to a nearly constant value (it saturates) as the number of pile is increased to five and nine. Moreover, the lateral deformation of piled raft system drastically reduces (around 2.4 times) for two pile system, and it saturates to a constant value with five and nine pile system. All these results indicate the constancy of stiffness irrespective of the number of piles in the piled raft.

Jan 1, 2015