Search Documents

By George Aristorenas, Carlos Englert, Jesús Gómez

"Laboratory test data of strain softening soils exhibit the development of a maximum (peak) shear strength followed by a decrease in the strength with continued straining. The rate of strength loss decreases such that an asymptotic minimum value, known as the residual strength, is approached. This paper presents an investigation of the evolution of strength degradation in excavation supported soils that exhibit strain softening behavior. The paper presents a numerical investigation of excavation support of slicken-sided clay, and results of shear testing on materials with similar strain softening behavior. A strain softening constitutive law is presented that can be used with the finite element computer software Plaxis for analysis of excavation support. A typical design section of a deep excavation support in stiff, fissured clay is presented that illustrates the limitations and conservatism of the residual strength approach for excavation support design. Finally, a discussion is presented on the impact of stiffer walls such as diaphragm walls, compared to less stiff systems such as sheet piles, on the design parameters.INTRODUCTIONIn the Washington, D.C. metropolitan area, the Potomac Formation is generally composed of stiff, fissured clays. Geotechnical engineers often associate the presence of slicken-sided planes within the formation as evidence that the soil cannot develop its peak strength. Although it is unclear how old and continuous these slicken-sided planes are, their occurrence, persistence and orientation appear to be somewhat random. Due to this uncertainty, the design of open cut slopes in these materials is often conservatively performed assuming residual shear strength values. This design approach may be justified for long-term open cuts when there is limited amount of geotechnical information and in view of back stability analyses of past slope failures. Furthermore, the lack of confinement in open cuts allows relatively high shear strains near the surface and toe throughout their existence, which promote mobilization of post-peak strength values and the ensuing progressive failure. Indeed, such behavior has been discussed in the past (Skempton, 1970; Schnabel et. al., 1982; Derrenbacher, 1998). A thorough study by Mesri et. al. (2003) of numerous slope failures concludes that the lower bound strength for stability analysis of non-failed slopes is the fully softened strength, which is intermediate between the peak and residual strengths, but that part of the slip surface may be in a residual condition prior to failure."

Jan 1, 2015

By Samer Rabab’ah, John C. Niedzielski, Jason Valeria

The PHX Sky Train is an automated people mover system located at Phoenix Sky Harbor International Airport. Phase II of the PHX Sky Train includes the design of over 150 drilled shafts for support of four guideway abutments, 75 guideway piers and three proposed stations. The soil conditions in this area generally consist of alluvial Sand, Gravel and Cobbles (locally known as SGC) deposited by the nearby Salt River. The foundation system will support relatively high axial loads, lateral loads and moments due to the height of the elevated guideway above the ground surface, where it needs to pass over roadways, parking lots, an existing terminal, and other buildings. Deep foundation design involves designing drilled shafts within the SGC deposits, some of which extend below the long-term groundwater table. Such extreme design loading conditions, together with difficult ground conditions at the site, result in several challenges for the design and construction of the deep foundation system for the project. This paper will present the results of a drilled shaft load test program implemented to provide site-specific measurement of the axial and lateral performance of the project drilled shafts. The load testing program consisted of a bi-directional load cell axial load test and a lateral load test performed on an instrumented test shaft 84 inches in diameter. The development and execution of the load test program and analysis of the test results are discussed. Comparisons were developed between predicted load capacities of drilled shafts using different design methodologies and the load capacity measured from the load tests. The load test results showed that underestimation of the capacity is evident using conventional methodologies. The load testing program was important for verifying the performance of the drilled shaft foundations on the project and was used to reduce the size of the drilled shafts. INTRODUCTION The PHX Sky Train is a five-mile long automated people mover system situated at-grade and on an elevated guideway which connects terminals, parking facilities, a rental car center and the Valley Metro Light Rail system in Phoenix. The purpose of this automated train system is to provide a secondary transportation system within the airport to relieve roadway congestion, minimize wait times and travel times for passengers and provide climate-controlled waiting areas. Phase 1 opened to the public on April 8, 2013. Phase 1A opened on December 8, 2014.

Jan 1, 2019

By Anburaj C., Srinivas A.

Deep excavation with support system is required to construct various part of underground structures like shafts, stations and entry structures etc. These structures have to be constructed using permanent or temporary embedded retaining walls with support system. The selection of a suitable type of retaining wall will depend upon the geological condition present in the particular location, time, cost and available equipment etc. In Bangalore Metro Rail Project, secant pile wall is adopted as the temporary earth retaining system and depth of excavation is about 20 m. It is designed initially based on bottom up construction methodology with 3 level of struts and 3 level of anchors but at later stage due to time and other construction related issues, it is decided to change the configuration to 6 levels of strut. Generally, in deep excavations, all the underground structures should be designed and checked for the critical forces from both permanent stage and construction stages. Since, secant piles are used as temporary retaining wall, only construction stage analysis is carried out to get the governing forces and deformation. In construction stage analysis, soil layers are defined with boundary conditions and the surcharge during construction and surcharge from actual building near the secant pile are considered. This paper discusses the effect of change in the support system from anchors to struts and how these changes in the support system affect the behavior of secant pile and subsequently adjacent buildings present in the influence zone of the excavation. As a result, in changing from anchors to struts, the wall displacement, strut forces and ground movement on the adjacent ground and buildings increases. The increase in deflection, ground movements and strut forces occurs during backfilling sequence of the underground station excavation. During backfilling, struts has to be removed and this imparts higher magnitude in deflection, strut forces and ground movements.

Nov 1, 2022

By Jahnavi Parmar, Pranav R. T Peddinti, Saloni Pandya, P. S. Prasad

Coastal cities are in desperate need of suitable land to meet the ever-increasing demand for urban infrastructure to support commercial, residential, tourism, and off-shore activities. Countries with a lengthy coastal line, such as India, possess significant areas of wide spread highly saline soils subjected to periodic seawater intrusion. One such soil stratum was encountered at the Gulf of Cambay, Bhavnagar district, Gujarat, India. Due to the high volume of river runoff, the Gulf has a positive water balance. The relative humidity ranges from 65 to 86 percent, making the climate semi-arid to sub-humid. The high salinity, mineral content, basaltic origin, and deeper water table offered the impetus to investigate applicability of various soil treatment options for such saline soils. Admixture stabilization techniques have been shown to help with problematic soil features. The Current study aims to determine effectiveness of addition of locally available lignite fly ash (10% - 30% by weight) and cement (6% - 9% by weight) to Bhavnagar saline soil in respect of strength, electrical conductivity and CBR. In this assessment, a comparison of stabilized and unstabilized saline soil mixtures is expected to highlight the need of understanding influence of treatment on instinctive performance of stabilized saline soils, as well as assist practitioners in efficacious treatment of extreme saline soils for diverse geotechnical and construction applications.

Sep 1, 2022

By Kevin Green, Iván Contreras, Aaron Grosser, Jon Ausdemore, Rachel Leier, Amr Ragy

"Construction of a new tailings dam was required to increase tailings storage capacity at a trona mine near Green River, Wyoming. The new dam was founded on overburden soils underlain by both fractured and competent bedrock. The stored tailings and water had high salt content, resulting in salty seepage water. To reduce the impact of the salty water on groundwater and the Green River, the design of the new tailings dam included a 257,260 SF (23,900 m2) seepage cutoff extending into competent rock.An extensive subsurface characterization was performed prior to completing the design and suitable seepage cutoff methods were evaluated. The approach selected was a full replacement panel using hydromill and clamshell for construction and self-hardening slurry (SHS) for the wall material. Laboratory testing was performed and ongoing monitoring has continued to evaluate the hydraulic conductivity and seepage cutoff performance in the briny environment.The paper includes project background, the collaborative approach and outcomes of the QA/QC program, and the monitoring results for the seepage cutoff wall.PROJECT BACKGROUNDCiner Wyoming, LLC (formerly OCI Wyoming, LLC) owns and operates the Big Island Mine facility near Green River, Wyoming. This underground trona mine has produced soda ash since 1962. The Greater Green River Basin covers much of southwestern Wyoming and extends into northeastern Utah and northwestern Colorado. The Ciner facility is located in the Green River Basin, which is part of the Wyoming Basin physiographic province. The Green River runs to the west and the south of the Ciner facility.Beginning in the early 1990s, Ciner primarily disposed tailings underground in mined-out panels. However, in recent years, underground storage has become limited and some disposal has transitioned to the ground surface. Long-term planning revealed a need to expand Ciner’s surface tailings disposal capabilities. Pond 2, a previously permitted disposal area, was identified as the most viable location for a storage facility. The Pond 2 site is directly north of the Ciner plant facilities, northwest of the active Upper Delta tailings storage facility, and northeast of the Green River (Fig 1)."

Jan 1, 2016

By Packer M. L

Residual load development in driven precast piles has been widely researched in recent decades, however, cast-in-situ piles are often falsely assumed to be unaffected by this mechanism. In contrast to driven precast piles, driven cast-in-situ (DCIS) piles require adequate time prior to loading for the concrete hydration and curing processes to occur. The concrete-soil interaction is complex with several processes influencing the strains within the concrete pile after installation. DCIS piles are of particular interest given that residual loads can be developed during both the driving and casting phases. This paper present four instrumented end-bearing DCIS piles in which temperature and strains were monitored from installation, with the objective of identifying the processes contributing to the measured strains prior to testing. Strain gauges at all depths recorded a net compression and compressive strains continued to increase up to the commencement of load testing. Residual strains in the test piles were interpreted to be influenced by temperature (concrete and ambient soil and air temperature), consolidation of soils due to dissipation of excess pore water pressure, and swelling from absorption of groundwater. Several residual load interpretive methods are evaluated with the Siegel and McGillivray (2009) approach being consistent with the skin friction full mobilisation theory of the Unified Design method. The full-scale field tests presented herein provide a unique opportunity to examine DCIS pile behaviour, particularly given the lack of presently available published studies on these pile types.

May 1, 2022

By Antonio Zechini, Giuseppe Iorio, Massimo Grisolia

"The new C Line of the Rome Metro runs northwest to southeast across the city center, with 30 new stations and a total length of more than 15.5 mi (25 km). Due to the presence of a dense urban environment, the selected solution for the construction of the stations consists of a cutand- cover excavation, which is retained by multipropped diaphragm walls to minimize settlement and prevent damage to the nearby structures. The bottom of the excavation of the underground stations are about 82 ft to 98 ft (25 m to 30 m) below ground surface, and about 66 ft to 82 ft (20 m to 25 m) below the groundwater table. To ensure dry conditions and to prevent hydraulic base heave instability, deep well systems were designed and used to lower groundwater level and piezometric head during excavation. The dewatering field tests showed how the local stratigraphy strongly affects the dewatering efficiency. Finite element modeling (FEM) of steady state filtration were used to compare the soil permeability with Lefranc in-situ test results and to verify the efficiency of the grouted plugs. The geological sequence along the new C Line consists of a very heterogeneously layered deposit. The base deposit of stiff overconsolidated clay (“APL,” Pliocene age) is overlain by fluvio-palustrine very dense sandy gravels (“SG,” Pleistocene age), which are then overlain by medium stiff clayey silts or dense sandy silts (“AR” or “ST,” Paleotevere units). These deposits are overlain by covered by pyroclastic volcanic soils, tuff, silty sand and sandy silt (Middle to Upper Pleistocene) deriving from the Colli Albani apparatus. A layer of made ground (“R”) of varying thickness covers the stratigraphic sequence and the natural soil profile everywhere.The local hydrogeological framework is very complex and characterized by a double groundwater system. The upper main aquifer is mainly represented by the “pozzolane sequences” (“PR/PN”), while the lower aquifer consists of a deposit of sandy gravel (“SG,” Pleistocene), which is underlain by marine claystone bedrock (“APL,” Pliocene). The pyroclastic deposits (e.g., pozzolane, lithoid and pseudolithoid tuff and clayely tuff) show large variations in permeability due to porosity, compaction processes, sealing and secondary fracturing. Permeability values for each soil type were determined using Lefranc tests at variable head and using pumping tests. The Lefranc tests indicated a wide range of permeability."

Jan 1, 2017

By J. Erik Loehr, Andrew Z. Boeckmann

"Poor drainage is a common cause of poor performance of earth retention systems, resulting in burdensome serviceability problems that can progress to outright failure of the retention system if not addressed. A drainage system consisting of filtered conical drains that can be installed through the face of an existing retaining wall and readily maintained was evaluated through tests of physical and numerical models. The physical models were constructed with different backfill materials in a container measuring 8 ft wide by 4 ft tall by 15 ft long. Tests were conducted by saturating the backfill under a constant water elevation atop the model, and then maintaining the water elevation until seepage from the drains reached a steady state condition. Pore pressures within the backfill and outflow from the drains were measured to facilitate calibration of numerical models that accompany the physical models. Results from the calibrated finite element models were used to develop design criteria for the drains. The design criteria establish the required drain spacing as a function of the height of groundwater above the drains and the diameter of the drain.INTRODUCTIONMany retaining wall performance problems are a result of poor drainage of the wall backfill. Consequences of poorly drained backfill include displacement and rotation of the wall face, including the extreme case of collapse, and seepage through the face of the wall, which is in turn associated with damage from corrosion, dry rot, and other forms of deterioration. A common approach to improve drainage of an existing wall is the installation of drainage features (e.g. “weep holes”) in the face of the retaining wall. Weep holes facilitate controlled seepage through the face, which relieves water pressure within the backfill and directs seepage to known locations in the wall face. Although installation of weep holes is relatively common, engineering methodologies for selecting the size (diameter) and spacing (along the wall) of facial drainage features are uncommon if not altogether non-existent. This paper documents tests of physical and numerical models of retaining walls with facial drainage features, including conventional weep holes as well as maintainable drains installed through the face and extending into the wall backfill. Results of the testing were used to develop generic design criteria, which establish the required drain spacing as a function of the height of groundwater above the drains and the diameter of the drain."

Jan 1, 2016

By Nicolas Moscoso, Gerald Verbeek, Marcel Bielefeld, Rob van Dorp

Upon recently, most offshore foundations were based on a number of driven piles that were installed with an impact hammer. With the increase in offshore windfarms two major developments have occurred: the shift from jackets to monopiles, leading to increase of the diameter of the foundation piles, and a shift from impact hammers to vibro hammers. As the use of vibratory hammers is becoming more and more common practice, the need for accurate vibro-driving simulation software has increased, which requires that the soil modelling is enhanced to address soil fatigue during pile driving and to predict reliably the soil behavior and resistance during pile driving. In addition pile driving monitoring, which is routine for piles driven with an impact hammer, needs to become common practice. This paper addresses advances in soil modelling that allows more accurate pile driving simulation as well as the application of Vibro Driving Analysis (VDA) or Monitoring (VDM) to validate the simulation results. This is illustrated by a case study of the test pile for the Delft Offshore Turbine project, a 28 m long monopile with a diameter of 4 m that was driven 15 m into dense sand layers using a vibro hammer. After some 6 months the pile was extracted, and pile driving simulations and VDA were done both for the installation and extraction phase. 1. INTRODUCTION At the end of 2017, the total worldwide offshore wind power capacity was 18.8 GW [1]. The vast majority of offshore wind farms are currently in Northern Europe, which together account for over two thirds of the total offshore wind power installed worldwide, followed by East Asia, while developments in North America are still in very early stages.

Jan 1, 2019

By Ramanathan C, Prasad P. V. S. R

The most critical challenge for any large size storage structures to be constructed on soft compressible soils is bearing capacity and consolidation settlements. Consolidation is the time dependent phenomena, as expulsion of water from soil voids on application of external load will take longer period. It is mainly influenced by soil consistency, permeability, thickness of compressible stratum and presence of free draining layers. This study deals with the foundation solution of a large size Mounded Storage Vessel (MSV) to be constructed on thick compressible stratum whose loading intensity is around 155 kPa and the estimated settlements are greater than 400 mm. Hence, the foundation solution using vibro stone columns is adopted as an effective technique to address the challenges of excess settlements and inadequate bearing capacity. Further to keep settlements within the permissible limit of 50 mm, preloading technique with 60% of actual loading intensity will be utilized. The consolidation analysis of stone column reinforced foundations is carried based on the method given by Han and Ye (2001). The quality of the stone columns is ensured by real time quality control measures and the performance of the stone columns shall be ensured by vertical load tests. Ground settlements was closely monitored with proper instrumentations and the actual degree of consolidation has been verified by Asaoka’s (1978) method.

Sep 1, 2022

By Christopher J. Ramsey, Don W. Dotson

"An existing four lane section of US 27 was widened to eight lanes. The project lies in the rugged Valley and Ridge Province of the Appalachian mountains starting at the Tennessee River in Chattanooga, Tennessee and extending 2.6 km north to Signal Mountain Boulevard. This terrain presented many challenges to accommodate the road widening in the narrow, rugged topography. Multiple tiered wall systems consisting of large tieback walls, post-tensioned reaction blocks, and gravity MSE walls for a total of approximately 30 retaining walls were required. The retaining walls served to stabilize the thrust faulted geology while also minimizing right-of-way acquisitions. The cut walls consist mainly of a tiered system of tied-back soldier piles walls with cast-in-place concrete facing. Cast-in-place pile shear walls were required along the toe of existing MSE walls to maintain stability during construction. This paper discusses the design methodology, which includes a hybrid (rather than traditional) earth pressure diagram intended to reduce life-cycle maintenance and long-term performance. Further this paper addresses wall construction, slope stability analysis, landslide mitigation alternatives, soldier pile wall design features, site challenges, monitoring and performance (to date) of the wall systems.INTRODUCTIONThis project involves the proposed widening of US Highway 27 (State Route 29) from the north end of the Tennessee River Bridge at Manufacturer’s Road to State Route 8 (Signal Mountain Road), approximately 2.64 km of roadway (Fig. 1). The project site is located adjacent to the Tennessee River on the north side of downtown Chattanooga, Tennessee in Hamilton County. The existing, limited access highway is to be widened from four lanes (two northbound and two southbound) to a minimum of eight lanes. Some portions of the alignment will expand to as much as ten lanes where northbound and southbound ramp acceleration/deceleration lanes coincide.In addition to the number and heights of cuts and fills involved, a major factor in determining an economical design for the alignment is the complicated geologic conditions along the roadway alignment. The existing roadway is situated between several steep cut slopes, some of which are only marginally stable or currently exhibit signs of instability. Due to the proximity of the project to the downtown area, the steep slopes along the alignment, and the relatively dense population near the alignment, widening the pavement and constructing cut and fill slopes to a stable configuration would result in major land acquisition for slope right-of-way."

Jan 1, 2015

By John P. Turner, Mark Jen, Bobby Daita

"The Port Authority of New York and New Jersey is replacing the existing Goethals Bridge built in 1928 which is deemed to be functionally obsolete. The replacement bridge will consist of a dual cable-stayed Main Bridge crossing the Arthur Kill with elevated approach spans connecting Elizabeth, New Jersey and Staten Island, New York. The main bridge towers are supported on a group of six nine-foot diameter drilled shafts that transition into a pier cap. The anchor and approach piers are supported on two column bents with each column supported on a single drilled shaft. The 4.5 to 10 feet diameter drilled shaft foundations have permanent steel casing to rock and socketed into bedrock. Subsurface conditions consist of Passaic Formation bedrock overlain by varying thicknesses of overburden soils. The foundation design assumes permanent casing extending a minimum 2 feet into the weathered bedrock. Rock socket lengths below the permanent casing vary between one to two shaft diameters based on the quality of the bedrock. The reinforcing design was based on AASHTO LRFD minimum requirements, force demands, seismic detailing requirements and also considering the continuity between the shaft and socket.The bridge is currently under construction with approximately 70 percent of the foundations installed. Several field conditions encountered at various stages of shaft construction between casing advancement and concreting required design and construction modifications. Based on the driving method and the quality of the bedrock, the tip of the permanent casing hit refusal either above or below the design elevation, requiring modifications to the drilled shaft design and its reinforcement. This paper provides an overview of the general subsurface conditions at the site and its impact on foundation design and discusses the detailing worked into the design to accommodate tip elevation variations, as well as various foundation design modifications in response to actual conditions encountered during construction."

Jan 1, 2016

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

A Smart Cell is a closed-type tip post-grouting device that is attached to the bottom of the steel reinforcement cage of a drilled shaft and is used to enhance performance and to reduce uncertainty thereof. Control of the grout is maintained within the device during injection and a uniform stress is imparted across entire base area simultaneously, inducing a pre-mobilization load into the shaft as well as the soil. This paper describes the construction and tip post-grouting of drilled shafts from two bridge projects in the Santa Cruz, Bolivia region along the Paraí River. During the grouting process at each project site, there were noticeable differences in the grouting pressures achieved and responses observed, even within short distances between shafts. For this project, the greater benefit of using the Smart Cells was the reduction of risk and uncertainty of performance due to the highly variable soil conditions. Ultimately, since the response of each shaft was observed during grouting and because a “minimum” value of shaft resistance (i.e., pre-mobilization of load) was measured, there is a greater reliability with the anticipated performance of the shafts when axial loading is eventually applied.

By Rick Deschamps

A reoccurring problem with support of excavations in urban areas involves the placement of external support components like anchors or nails in right-a-ways, subway and utility setbacks, in areas occupied by adjacent structures, and within the property of non cooperative neighbors. Such a situation occurred for a project in Arlington, Virginia, which ultimately resulted in the preliminary design of a large footing supported cantilever retaining wall that was extremely costly and impractical to build. An innovative design alternate consisting of a series of vertical concrete elements (VCEs) supported by post tensioned tiedowns was proposed to the General Contractor and accepted by the owner. The VCEs were designed to serve as the main structural elements for both the temporary support of excavation system and the permanent wall. The VCE?s were constructed using single bite diaphragm wall panels oriented perpendicular to the excavation face including a rebar cage and tremie concrete. Threaded inserts were placed within the rebar cage to attach the cast in place exterior wall. Overall stability and lateral movement of the VCEs were controlled by high capacity vertical anchors embedded within the VCE. A detailed instrumentation program was installed to monitor the movements of the VCEs with relation to the excavation depth. The paper present the project case history by discussing the design concepts of the VCE, the construction approaches used to install them, the construction challenges encountered, and the performance of the unique system.

Jan 1, 2008

By Carlandrea Albonico, Salvatore Miranda

The paper describes an innovative geotechnical engineering solution that has been provided within the scope of the Galataport Project, in Istanbul, Turkey. Among all interesting geotechnical works included in the Project, this paper presents the design principle, adopted technologies and performance controls related to the Multi- Purpose Bottom Plug (MPBP). This original geotechnical engineering solution has been employed for the deep basement excavation in Karaköy and consists of a combination of seepage control, ground improvement, and load bearing elements, which have been executed with double-fluid jet grouting, pseudo-elliptical jet grouting and permanent micropiles, respectively. The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high-profile Project.

Nov 1, 2022

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"The use of steel screw piles has greatly increased in recent years because of the advancement in the installation mechanism and its performance under compressive, uplift and lateral loads. In a steel pile system, the strength of pile material limits the end bearing resistance of the pile due to strong subsurface conditions. The installation mechanism of screw pile can reduce the end bearing resistance due to the torque and axial force. However, if the installation mechanism does not reduce the bearing resistance of the pile, another important factor that can reduce its performance is the strength of the helix/wing plate. In this study, the effect of wing plate deformation on the performance of single helix/wing plate pile bearing resistance investigated. A model ground was used to investigate the effect of wing plate deformation. Dry Toyoura sand was used as a ground material and was compacted to denser states of 80% and 92%. The shaft and wing plate material of the pile was the same to actual piles that are used nowadays in Japan. A series of load tests were performed with different wing plate diameters and thicknesses. It was observed that deflection in the wing plate reduces the bearing resistance of the pile. The increase in the thickness of the wing plate was seen to restore the reduced pile resistance due to deflection. It was also observed from the experimental results that the ratio of wing plate diameter to shaft diameter (Dw/Ds) greatly affects the deformation of wing plates, which ultimately affects the end bearing resistance of the pile. The results obtained in this research suggest that the outstand length (Lw) of wing plate should be less than 5.6 times the thickness of wing plate for piles having a large Dw/Ds ratio under strong ground conditions.INTRODUCTIONThe first use of screw pile was almost 180 years ago by Alexander Mitchell. He patented his invention in 1833 with the name “Screw Pile”, and used it for ship moorings. The use of screw piles has since been adopted in various areas such as lighthouses, fencing for agriculture and marine structures. The use of screw piles in civil works started in 1985, after the invention of the hydraulic torque motor, as it eases the installation process. Nowadays, screw piles are used in the foundation of transmission towers, elevators, buildings and many other civil structures.Screw pile has an edge over other steel pile systems due to its high bearing, uplift and lateral resistance. The end bearing resistance of screw pile depends on installation, strength of subsurface material and the pile material. The screw pile is installed by applying torque and axial force. The pile torsional strength should be more than the applied torque and axial force to avoid deformation before reaching the final depth."

Jan 1, 2015

By Karen C. Armfield, Gisele R. Passalacqua, Joanna Smith

New York City is an urban environment with a history spanning over 200 years. The coastline of New York has changed over the years. In the East River, old bulkhead and remnant of relieving platforms together with variable bedrock elevations pose challenges in the design and construction of deep foundations. This paper presents a Case History of high capacity deep foundations along the Franklin D. Roosevelt (FDR) Drive on the Upper East Side in New York City. The project consists of a ramp that overpasses the FDR Drive allowing heavy trucks to access the Marine Transfer Station (MTS) facility built over the East River. Large diameter drilled shafts and mini-piles socketed to bedrock were designed and constructed. Remnant of old bulkhead was encountered at the site and a Ground Penetrating Radar (GPR) investigation was completed during the subsurface investigation phase of the design. This paper discusses details of the subsurface investigation program and design methodology of the high capacity drilled shafts and mini-piles. It also describes construction methods and results of Osterberg Load tests documenting the field values of skin friction through the rock socket. Other construction challenges include construction and drilling rock sockets for drilled shafts over sloping bedrock. 1. INTRODUCTION New York City is a renowned urban city that always calls for the most delicate, yet complex, and robust superstructures and most importantly substructure designs. The historic preservation of this large 200 years old city of 319 square miles is ever changing. Shorelines are often extended to accommodate new infrastructure and very often many miscellaneous structures are discovered below the ground surface. The East 91st Street Ramp was constructed to provide access to the East 91st Street Marine Transfer Station over FDR Drive and York Avenue. Another alternative ramp will be relocated to the South Bound (SD) of the FDR Drive at 92nd Street. A subsurface exploration program was completed in accordance with the New York City Department of Design and Construction (NYCDDC) general requirements, Section 4.5, to perform subsurface investigation along the FDR Drive in Manhattan, New York.

Jan 1, 2019

By Shawna Munn, Carol Dounitch, Erika Acton

The EQ Bank Tower, a 24-storey office tower with 4 levels of underground parking, is currently under construction at 25 Ontario Street in the downtown core of Toronto, Canada. The tower geometry required an 18 m (60 ft) deep excavation inside an existing 3-storey 100-year-old façade, to be retained in place throughout construction. This presented a variety of design challenges that required several innovations and a customized monitoring program. In this paper, we will discuss two major challenges, and highlight the innovative and adaptable solutions carried out using performance-based design leveraging the observational method. The first was installation of a shoring system in a 500 mm (20 in) gap between the historical façade and a live gas main. The second involved excavating 10 m (33 ft) into expansive shale bedrock adjacent to a sensitive neighbouring building.

Oct 1, 2022

By K. S. Ho

With the aid of the advanced electronic devices and micro-processors, the quality control of deep foundations can be carried out by Non-Destructive Tests (NDT). Three methods are presented here: the Sonic Logging, Vibration and Stress Wave Analysis Methods. The principles, equipments used, testing procedures and applications are fully described. The correlation of these methods with the conventional tests (mechanical coring and loading test) are studied to give a better understanding of the methods. Several case histories with the test results obtained from a number of sites in Hong Kong and overseas are discussed to show how the pile quality can be examined and especially, how to confirm the effectiveness of remedial works on a defective pile. Recommendation on the percentage of piles to be tested are given at the end of the paper by using statistical method.

Jan 1, 2010

By Nathan W. Iverson, David S. Graham, Paul J. Axtell

"The Highway 53 relocation project in Virginia, Minnesota, involves construction of a very tall bridge across a currently inactive iron ore mine pit. The inactive pit is partially flooded and serves as the community’s drinking water source. The 1,132-ft long new bridge is a three-span, plate girder structure. Two intermediate, approximately 200-ft tall piers are located within the pit.The foundations for the two piers consist of groups of 30-in diameter piles which, despite the contradiction in terms, are essentially very large micropiles. Extremely challenging and highly variable subsurface conditions exist at the site, ranging from uncontrolled iron ore mine waste fill to some of the hardest rock on earth that can also be highly fractured and abrasive. Despite the conditions, large diameter (30-in) micropile foundations up to 175 ft deep were successfully installed using down-the-hole hammer methods and full-length permanent casing under an extremely aggressive construction schedule.Full-scale foundation load testing using the Statnamic rapid loading method was also conducted in support of the design and construction but under a separate pre-design phase contract. This paper describes the unique aspects of this foundation project, including design, construction, and load testing of the large micropiles.INTRODUCTION AND BACKGROUNDIn 1960, a segment of Trunk Highway 53 (TH-53) in Virginia, Minnesota, was built on land owned by iron ore mining interests. As part of the roadway easement agreement, Minnesota Department of Transportation (MnDOT) was to be given notice three years prior to termination of the easement. In 2010, MnDOT received notice that the mining interests wished to access the ore. Through negotiations in 2010, MnDOT and the mining interests agreed to a 2017 date for abandoning the existing section of roadway. During this period, MnDOT needed to procure project funding, satisfy environmental permitting requirements, and acquire new right-of-way to permanently reroute TH-53 and keep it open to traffic. This was no easy task due to the existing mine pits surrounding the area.The E-2 alignment option shown in Fig. 1 was ultimately selected for the rerouted highway in 2014. The new highway segment includes a three-span bridge across the currently inactive Rouchleau Mine Pit. The inactive pit is partially flooded and serves as Virginia’s drinking water source. The 1,132- ft long new bridge is a three-span, plate girder bridge. Two intermediate approximately 200-ft tall piers are located within the pit. Fig. 2 is a conceptual rendering of the bridge."

Jan 1, 2017