Search Documents

By A. R. Farkoosh, K. Korgiopoulos, McGill University, O. Rodop, L. A. Villegas Armenta

"New generation of Al-Mg-Si alloys with thermally stable dispersoids that prevent recrystallization and grain growth during hot deformation are currently used in automotive components requiring good formability. Alloy chemistry controls the phase formation especially age-hardening precipitates, dispersoids, and primary intermetallic which have pronounced effect on grain structure, strength and formability. In this work, thermodynamic calculations have been used to predict the effects of varying levels of Si (0.5-1.5wt%), Mg (0.5-1.5wt%) and Mn (0.1-2.5wt%) on phase selection. Thermodynamic calculations have been performed in equilibrium and non-equilibrium conditions via the FactSage™ software using the FTlite database. Selected compositions have been cast, heat treated, extruded and characterized through scanning electron microscopy with energy dispersive spectroscopy and electron channeling contrast imaging techniques. The calculations showed that at the hot deformation temperature of ~540 oC, exceeding certain Mg and Si levels would lead to retained *-Mg2Si intermetallics and Si particles at the grain boundaries in addition to a-Al-(Mn,Fe)-Si. It was found that retained *-Mg2Si phase which adversely affects formability can be avoided for Si+2Mg levels lower than 2.3wt%. FactSage calculations also showed that increasing Mn from 0.5wt% to 1wt% leads to an increase in the amount of dispersoids (from 1wt% to 2wt%) that can potentially slow down recrystallization and grain growth during hot deformation and improve formability. Calculations at room temperature also show that for an alloy with 0.7wt% Mg, excess Si beyond 0.7 wt% promotes the precipitation of Si clusters in the Al matrix that accelerate natural age-hardening. Results were confirmed by experimental investigation.INTRODUCTIONAluminum alloy 6082 (Al-Mg-Si) is used in the automotive industry because of its high strength, and good weldability (I. J. Polmear, 2006). The alloy is age-hardenable through the precipitation of ß-Mg2Si and its precursors, and the recrystallization is usually inhibited by Mn- and Cr-containing dispersoids formed through high temperature heat treatments (I. Polmear & Couper, 1988). However, it is known that minor changes in alloy chemistry (Mg/Si ratio) can have significant influences on the ductility and formability of these alloys by altering phase selection and the resultant microstructure (Gupta, Lloyd, & Court, 2001; McQueen & Celliers, 1997; Zajac, Hutchinson, Johansson, & Gullman, 1994). For automotive applications where wrought alloys (usually extrusions) are cold-formed to produce suspension components, the chemistry of the alloys and the extruded structure are of crucial importance as they determine the formability at room temperature (Asensio-Lozano, Suárez-Peña, & Vander Voort, 2014). In this study, thermodynamic calculations along with experimental investigations were carried out on the Al-Mg-Si system to understand their phase formation and precipitation hardening as a function of alloy composition."

Jan 1, 2016

By A. E. Taylor, A. S. Judge, P. T. Lafleche

"Resource development in northern Canada has special requirements which derive from the unique environmental and eco-logical nature of the northern environment. In this paper several case histories in which the Permafrost Research Section of the Geological Survey of Canada (GSC) has participated are used to illustrate how geophysical methods may be used to address some of these considerations. Although some of these examples were developed while examining problems directly related to oil and gas development and transport in frontier regions, such or similar methods also have application to mining problems.IntroductionA critical parameter is the distribution and thickness of permafrost, which in northern Canada varies from being a few metres and discontinuous at the southern limit to thicknesses in excess of 700 m in the Arctic Islands'!'. Figure I is a schematic diagram of typical ground thermal conditions in a permafrost zone. The upper zone is defined by an active layer which undergoes a seasonal freeze/thaw cycle. In the simplest case, the ground remains permanently frozen below the active layer to the depth of the O°C isotherm, which is defined as the base of the permafrost. Water chemistry, pore structure and pore or grain size may cause the base of the frozen ground to be above the permafrost by up to 100 m(2). Ice can be found within the permafrost in the pores of solid rock or sediments, as massive ice within unconsolidated sediments or as ice lenses within fissures in a solid rock mass. The mining technique used in these conditions, whether open pit or underground, can differ considerably from that used in southern Canada. In the high Arctic, for instance, the dry drift method is feasible underground in the permanently frozen host rock. The frozen nature of the wall rocks can obviate water-related problems."

Jan 1, 1987

By M. A. Tomlinson, A. Di Feo, T. C. Cheng

"Goldcorp is evaluating the potential for economic reprocessing of historic tailings at several sites, including the Aunor A facility located in Timmins. The overall project is investigating the ability to recover value, remove sulphide minerals and alternative tailings re-deposition strategies. Desulphurization of tailings will eliminate potential acid generation while improved tailings re-deposition could reduce long-term liabilities and closure costs. Through a task-share project between CanmetMINING and Goldcorp, tailings obtained from Aunor A site have been characterized using mineral association analysis and diagnostic separation techniques. The selected tailing samples contain about 2 g/t of gold. Mineralogical analysis has identified coarse agglomerates bound with gypsum and significant free gold, confirmed by high recoveries in cyanide leach tests. However, despite no evidence of surface passivation on the minerals, conventional flotation techniques were found to be ineffective in concentrating gold or sulphides due to the high fines content and highly agglomerated particles.INTRODUCTION Aunor Mine is one of the historic mines that belongs to Porcupine Gold Mines (PGM) in Timmins, Ontario. PGM has undertaken an extensive mine closure program to remediate the legacy and closed mines with the funding supported by operating mines since 2006. Over the course of 100 years of operation in the Porcupine camp, it is estimated (Stevens et al., 2013) that about 130 million tonnes of tailings have been generated. Aunor Mine produced 2.5 million troy ounces of gold between 1940 and 1984, while processing over 7.6 million tons of ore. The original gold grade of Aunor Mine ores was about 10 g/t. With 95% gold recovery at the time, an estimate of 0.5 g/t of gold remains in the Aunor Mine tailings. Aunor Mine has two tailings impoundment areas: designated as Aunor A and Aunor B. The two sites are similar in size, about 7 hectares each. The amount of tailings in the Aunor A site alone is about 3.2 million tonnes. In 2017, bulk tailings were sampled from five designated locations in Aunor A. They were characterized using mineral association analysis and diagnostic separation techniques. The bulk tailings samples contained about 10% total sulphur, 10% iron, 2% arsenic and 2 g/t of gold. The prime objective of this collaborative work between CanmetMINING and Goldcorp is to facilitate the timely development and deployment of innovative tailings reprocessing solutions, specifically in the areas of desulphurization, and recovery of metals. This work targeted specific tailings of interest to Goldcorp which goals are to improve its environmental footprint and to reduce long-term liability. Thus, it is imperative to look for innovative reprocessing options that can overcome not only technological challenges but also achieve economic benefits to offset the costs associated with reprocessing the tailings. Moreover, the greater goal is to demonstrate and deploy tailings reprocessing solutions to solve one of the industry’s most difficult challenges for a sustainable mining industry in Canada."

Jan 1, 2019

By J. Cayouette, C. Bolduc, P. Blatter

"The LaRonde mill was commissioned in 1988 and began treating ore from the Penna shaft in 2000. The mill has been expanded to accommodate 7,500 t/day, but ramped down to 6,000 t/day since the deep extension began. The process recovers gold, silver, and base metals. In 2008, the Goldex plant began trucking gold-pyrite concentrate to a treatment plant feeding pulp to the LaRonde mill, increasing gold output by 40,000 oz. In 2009, the high-grade Lapa ore processing facilities were annexed to the LaRonde plant, increasing gold output by 120,000 oz. This paper outlines the metallurgical considerations related to the treatment of different ore types.RÉSUMÉ Le concentrateur de la mine LaRonde a été mis en service en 1988 et a commencé à traiter le minerai du puits Penna en 2000. La capacité du concentrateur a augmenté afin de permettre le traitement de 7 500 tonnes de minerai par jour, capacité qui est retombée à 6 000 tonnes par jour (tpj) depuis le début de l’extension en profondeur de la mine. Ce procédé permet de récupérer de l’or, de l’argent et des métaux communs. En 2008, l’usine de traitement Goldex a commencé à transporter par camion du concentré de pyrite et d’or vers une usine de traitement alimentant en pulpe le concentrateur de LaRonde, augmentant ainsi la production d’or de 40 000 onces. En 2009, les installations de traitement du minerai à haute teneur de Lapa ont été annexées à l’usine de traitement de LaRonde, augmentant la production d’or de 120 000 onces. Cet article passe en revue les considérations métallurgiques liées au traitement de différents types de minerai.INTRODUCTIONThe LaRonde metallurgical plant in the Abitibi region of Quebec, Canada, evolved into a mature milling site following expansions in 2000–2003, thanks to improved processes, manpower, and water treatment capabilities that better accommodate the complex constituents of the LaRonde ore. The ore requires a sequence of grinding, copper- lead and zinc flotation, and precious metals leaching, ending with a carbon-in-pulp (CIP) gold recovery. A portion (35%) of the tailings is sent back underground as paste backfill after being treated with the SO2-air cyanide destruction process. The tailings area has a dedicated cyanide destruction and metal precipitation area through which the used water passes before returning as recycled water. A biological water treatment plant was built in 2004 to address water toxicity in the final effluent. The water toxicity was the result of the high sulfide content of the LaRonde ore (from thiocyanate or stable cyanide species buildup) and the use of 90% recirculated water in the mill. The water treatment plant uses bacteria to transform thiocyanate into nitrates and precipitate phosphorus from the water before it is discharged into the environment."

Jan 1, 2017

By Malcolm Scoble, Jean-Marc Robert, Luciano Piciacchia

"An approach to the in situ testing of mine backfills is outlined. It has been developed to provide a measure of the effective strength and stiffness of such materials after placement in stopes. This paper is based upon recent field studies undertaken at five Quebec mines. Details of the selected instrumentation, supporting equipment and testing procedures are reviewed. The mechanical behaviour of the backfills is reported and related to their physical properties. This approach represents an economical, simple and reliable means to assess the mechanical characteristics of backfill materials as an aid to both mine design and placement quality control. IntroductionDevelopments in backfill and mining method technology are creating a pressing need to develop effective techniques for characterizing the physical and mechanical properties of backfill in situ, rather than relying on traditional laboratory testing. The development of bulk mining methods is creating the requirement to more fully understand the nature of exposed fill faces to design for stability in pillar recovery operations. Other backfill technological developments currently receiving widespread attention are high density placement and the use of alternative additives to Portland cement. In Canada, U.S.A. and South Africa attention is also being placed on employing backfill to alleviate rockburst hazards(1,2.3l. In situ testing offers the potential to measure the geomechanical properties of backfill once placed in stopes , in order to assess its actual role in pillar recovery and ground support. Similarly, it offers the ability to provide some quality control during backfill placement. This role is seen as becoming increasingly important with the growing recognition of the need to pay greater attention to the mode of placement, which governs segregation and variation in the properties actually achieved by the backfill after placement."

Jan 1, 1987

By G. K. Jorgenson, S. H. Chung

"IntroductionThe SABREX Blast Modelling Program was developed jointly by the companies of the ICI Explosives Group, of which C-I-L Inc. is a member. SABREX (Scientific Approach to Breaking Rock with Explosives) is a modular computer program which incorporates new technology with a number of tested programs that have been in use world wide.SABREX predicts the performance of blasts in terms of (I) fragment size and distribution; (2) muckpile profile and face velocity; (3) grade fracture; (4) collar breakage; (5) a rupture envelope which depicts crack penetration behind and beneath blastholes; and (6) a complete cost analysis including explosives, drilling and accessory costs. The predicted blast results are displayed as dynamic colour graphics and in tabular form.SABREX uses data on the detailed geometry of the drilled and loaded pattern, detonation characteristics of the explosives and the dynamic properties of the rock to generate blast predictions. SABREX blasting calculations take into account the effects that shock and quasi-static pressures exert on the rock around the blastholes. While physical effects occur very rapidly in rock blasting, it is possible to view and model the sequence of events as discrete sections.The program can be run on a microcomputer and is currently operated by C-I-L technical service staff in Canada for the use of drilling and blasting operators.Figure I is a diagram representing the modules of the program and associated technology that is used to complement the program.Any, or all, of the modules may be used in a particular study or blast optimization. Because the BOBCAT module of the SABREX program has been described in previous papers(7.8.9), this discussion will concentrate on the newer modules: CRACK, HEAVE, RUPTURE ENVELOPE and to a limited extent, KUZ-RAM, which present a more detailed picture of the blasting process.Each of these modules is discussed in terms of the information they offer the operator in analyzing the blast. Specific examples of recent usage in Canadian mining situations are included to illustrate the ability of the model to produce practical results that can assist in optimizing actual blasting operations or solving problems that do exist."

Jan 1, 1987

By K. D. Hester

"1.0 INTRODUCTIONThe uranium industry started in Canada with the reopening of the gravity concentrator at Eldorado's Port Radium mine in the North West Territories in 1942. In 1948, uranium exploration and processing was opened to the private sector, and the Federal government offered special pricing incentives to the industry. Eldorado explored the Lake Athabaska deposits in northern Saskatchewan, and in 1953 opened the Beaverlodge mine. Other mines in the area soon followed. In 1953 also, the deposits in the Blind River - Elliot Lake area and in the Bancroft area of Ontario were discovered. Mines and mills were quickly developed in these areas.Canadian uranium production peaked at 15,900 short tons of U3O8 in 1959. In that year, uranium exports at $300,000,000 exceeded those of all other minerals in value. On October 1, 1959, Canadian uranium operations employed 13,900 people.Up to 1956, it was a seller's market. By 1958, world production of uranium was far ahead of requirements. Accordingly, in November of 1959, the USAEC announced it would not renew it's options for continued delivery of uranium from Canadian mines. This led to the ""stretchout"" of existing uranium contracts, and many mines were shut down (see Table 1) .In the early 1970's, a commercial uranium market seemed to be developing. In Ontario, at Elliot Lake and Bancroft, mines reopened. But competition was coming from the Athabaska basin of Saskatchewan. Currently it is these high grade, open pit deposits of northern Saskatchewan which are in the forefront of Canadian uranium developments. Canadian developments since 1942 reflect the political and market forces, as well as metallurgical progress and changes in environmental standards. This paper attempts to show these process changes in broad perspective."

Jan 1, 1987

By James A. Finch, Stéphanie Gélinas

"A colorimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determination in a series of industrial campaigns. Some frother observations are described, including: concentration evolution down a bank, distribution between pulp and froth phases, and a mass balance around a circuit. Minute amounts of frother in recycle water were also measured.The contribution of frother and alcohol by-products in the analysis was generally additive for plants using aliphatic alcohol type frothers and decoupled for systems using glycols. Typically, U250C (polyglycol) was used at higher concentration (>10 ppm) than MIBC (aliphatic alcohol) (<10 ppm) or F-150 (polyglycol) (<3ppm).The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimization of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimize the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.INTRODUCTIONOwing to the lack of analytical methods, the task of determining frother concentration in plant flotation circuits is not routinely performed. Industrial sites seldom outsource analyses that are both costly and inconvenient, due to the necessity of shipping freeze-dried samples to remote testing facilities. A more direct colorimetric method has recently been demonstrated for the laboratory characterization of common industrial frothers (Gélinas and Finch, 2004). The approach, based on the Komarowsky reaction (Penniman et al., 1936; Coles et al., 1942; Duke, 1947), was previously described by Parkhomovski et al. (1976) for methyl iso butyl carbinol (MIBC). The reaction involves the interaction of the OH group of a higher alcohol, concentrated sulphuric acid, and salicylaldehyde, to yield coloured solutions with intensities that can be analyzed by UV-visible spectrophotometry."

Jan 1, 2007

By F. Kitzinger

Electromagnetic testing of wire rope has become more and more reliable over the past two decades. This improvement is partly a result of an unprecedented progress of electronic technology, which permitted the development of a new breed of testing instruments. There are two basic methods for the electromagnetic testing of wire ropes, the AC method and the DC method. Both methods rely on magnetic field disturbance caused by mechanical anomalies in the rope structure. The wire rope under test is passed through a magnetic excitation field, which can be a weak alternating field or a strong static field. Because the alternating field is produced by an alternating current, these instruments are of the AC type(l). In the early days of ND-testing, strong permanent magnets were not yet available; therefore, the static magnetic field was produced electromagnetically with direct current. Instruments based on static excitation are still called DC instruments(2), even though the field is now produced by a permanent magnet. Both these methods have certain characteristic features. The AC method can detect loss of metallic area caused by corrosion or other effects, whereas localized faults such as broken wires are better detected by the DC instruments . The basic principles of the wire rope testers have remained unchanged over the years and the improvements present in the new instruments usually reside in the signal processing and recording sections. The Instrumentation Department of the Noranda Research Centre* has been involved in a four-year development program which resulted in a new type of wire rope tester, the Magnographv** . This new instrument in many ways represents a considerable departure from the traditional wire rope testers. The Magnograph has already been patented in Canada and the U.S.A.(3), and patent applications are pending in other countries.

Jan 1, 1979

By John A. Meech, Irene E. Cristoveanu

"The separation of hematite fines (100% - 38 um) from quartz fines (100% -75 um) was investigated using coarse hematite (-212 + 150 um) as a carrier in an oleic acid collector system. Oleic acid additions, per cent coarse additions, combined conditioning time and ferric chloride additions were examined.It was found that carrier flotation is a dominant mechanism for fine hematite recovery at oleic acid levels greater than 200 g/t and coarse additions of 10 per cent. Hetero-aggregation is favoured under conditions of lower levels of oleic acid in the presence of ferric chloride and at conditioning times greater than ten minutes.Ferric chloride acts as a depressant for pre-reagentized coarse hematite at oleic acid levels below 150 g/t. At concentration levels above 500 g/t, ferric chloride interferes significantly with the success of carrier flotation of fine hematite.The sensitivity of carrier flotation to changes in oleic acid addition, ratios of fine and coarse material, conditioning time and the presence of an inorganic electrolyte emphasizes that its application is only suitable when flotation conditions can be stabilized.IntroductionThe production of fine material is unavoidable during the comminution of iron ore . Due to the difficulty of recovering iron from this fine material by various gravity separation methods, flotation can often be a more attractive process producing high-grade material at high recovery. One variation of the flotation process, that can be useful for recovering ultra fine minerals (<10 um) , is known as carrier flotation. This process involves the utilizat ion of coarse particles ( > 150 p.m) which act as flocculation centres to which the fine hematite particles (10 - 40 u.m) become attached and are carried or "" piggy-backed"" into the froth phase."

Jan 1, 1985

By Michael J. Sapko, Ellsworth R. Spencer, Frank J. Perzak

"The fire resistance of several mine conveyor belts is evaluated using a new belt-flammability apparatus developed by the U.S. Bureau of Mines. The test apparatus, experimental details and a calculated flammability index (FI) are described.The FI values are useful for ranking the fir e resistance of mine conveyor belts. Values are determined using parameters readily measured with thermocouples, high-temperature flow probes and a methane-oxygen torch, all of which are components of the Bureau&apos;s new test apparatus. The FI varies directly with the flame-spread rate and the rate of heat release during burning and varies inversely with the critical (minimum) ignitor energy output.The fire-resistance ranking of nine different belt types using this moderately scaled apparatus is compared with available full-scale data on belt fires. This comparison shows that the ranking based on the FI is consistent with the full-scale data.IntroductionFull-scale fire hazard evaluations of mine conveyor belts are not easily related to the properties usually measured in small-scale flammability tests. The inadequacy of small-scale belt fire tests has been demonstrated in works by Mitchell, Warner and Reinke.Mitchell and Warner showed that certain neoprene (NP) and polyvinyl chloride (PVC) belts, which had been approved by the Code of Federal Regulations 30 CFR 18.65, were nevertheless capable of propagating flame over their entire length when full-scale fire conditions were simulated. Comparable results were also observed by Reinke at the Tremonia experimental mine in Dortmund, West Germany, where all belts burned in full-scale tests even though they passed the small-scale tests. Only by reducing the severity of the full-scale test could these fire-resistant belts be grouped on a pass-fail basis."

Jan 1, 1982

By F. Duan, J. Pfarr, J. M. Goris

"The U.S. Bureau of Mines, in cooperation with the Homestake Mining Co. and the University of Utah, is conducting a field demonstration to evaluate the behaviour of rock masses supported with cable bolts. One of two rock masses being studied is supported with both conventional and birdcage cables. This rock mass is located between the 6500 and 6650 levels of the 45-48N stope, 21 ledge. The second rock mass is the hanging wall of the D-limb stope between the 3500 and 3650 levels near the Ross Shaft and is supported with conventional cables. The primary objectives of the project are to monitor the behaviour of the two rock masses during mining using extensometers and cable support strain gauges, after which the rock will be modelled using the finite-element code UTAH III. Field data will be used to verify the modelling. In addition, a comparison between the effectiveness of conventional and birdcage cables will be made.45-48N StopeThe 45-48N stope is located in the 21 ledge between the 6500 and 6650 levels and contains about 233 000 short tons of mineable ore. The orebody lies within the Homestake Formation and is very irregular being approximately 200 ft long and 75 ft wide. Between the 6500 and 6650 levels, it dips from 35 degrees to 60 degrees east with a near-vertical plunge to the south. Mineralization is characterized by arsenopyrite and pyrrhotite with minor gold. The contact between the Homestake and the overlying Ellison Formation creates a plane of weakness along localized graphitic layers. The footwall dips at approximately 60 degrees but between 100 ft and 120 ft above the 6650 level , the hanging wall flattens to almost 20 degrees causing a significant mining problem."

Jan 1, 1991

By Harold L. Gibson, Don H. Rousell, Ian R. Jonasson

"Abstract - The Sudbury Structure consists of three major components: 1) the Sudbury Basin; 2) the Sudbury Igneous Complex which surrounds the basin as an elliptical collar; and 3) an outer zone of shatter-coned and intensely brecciated footwall rocks. Although the Sudbury Event which formed the structure may be unique, the area has, in fact, been shaped by a series of tectonic, magmatic and mineralization events which can be considered in terms of two Wilson cycles of continental extension and closure. The first cycle, from 2500 to 1700 Ma, included the following events: doming (uplift of Levack Gneiss Complex); NE-SW extension (Matachewan dikes); N-S to NW-SE rifting (faults, mafic intrusions, sedimentation, and Ni-Cu-PGE and U mineralization); NW-SE extension (Nipissing diabase, and Ni-Cu-PGE, Ag, Co mineralization); and NW-SE and NE-SW closure (Penokean Orogeny, 1900 to 1700 Ma) with superimposed meteorite impact (1850 Ma, Ni-Cu- PGE, Zn-Cu-Pb deposits). The second cycle, from 1700 to 1000 Ma, included: N-S extension (alkali metasomatism, Au); N-S extension (hornblende diabase dikes along the Murray fault set); NNESSW extension (olivine diabase dikes); NE-SW extension (Fecunis Lake fault set); and NW-SE closure (Grenvillian Orogeny).The rich and diverse Ni-Cu-PGE and subordinate Zn-Pb-Cu and Au mineralization of the Sudbury region is related to endogenic and impact-triggered crustal extension and magmatism. The Sudbury Structure apparently was the site of a triple junction or hot-spot. The Sudbury ores, although located within an impact structure, are analogous in terms of age and tectonic setting to Ni-Cu-PGE and Zn-Pb-Cu ores elsewhere in the world. Meteorite impact accentuated on-going ore forming processes and magmatism at Sudbury."

Jan 1, 1997

By Harold L. Gibson, Don H. Rousell, Ian R. Jonasson

"The Sudbury Structure consists of three major components: 1) the Sudbury Basin; 2) the Sudbury Igneous Complex which surrounds the basin as an elliptical collar; and 3) an outer zone of shatter-coned and intensely brecciated footwall rocks. Although the Sudbury Event which formed the structure may be unique, the area has, in fact, been shaped by a series of tectonic, magmatic and mineralization events which can be considered in terms of two Wilson cycles of continental extension and closure. The first cycle, from 2500 to 1700 Ma, included the following events: doming (uplift of Levack Gneiss Complex); NE-SW extension (Matachewan dikes); N-S to NW-SE rifting (faults, mafic intrusions, sedimentation, and Ni-Cu-PGE and U mineralization); NW-SE extension (Nipissing diabase, and Ni-Cu-PGE, Ag, Co mineralization); and NW-SE and NE-SW closure (Penokean Orogeny, 1900 to 1700 Ma) with superimposed meteorite impact (1850 Ma, Ni-Cu- PGE, Zn-Cu-Pb deposits). The second cycle, from 1700 to 1000 Ma, included: N-S extension (alkali metasomatism, Au); N-S extension (hornblende diabase dikes along the Murray fault set); NNESSW extension (olivine diabase dikes); NE-SW extension (Fecunis Lake fault set); and NW-SE closure (Grenvillian Orogeny).The rich and diverse Ni-Cu-PGE and subordinate Zn-Pb-Cu and Au mineralization of the Sudbury region is related to endogenic and impact-triggered crustal extension and magmatism. The Sudbury Structure apparently was the site of a triple junction or hot-spot. The Sudbury ores, although located within an impact structure, are analogous in terms of age and tectonic setting to Ni-Cu-PGE and Zn-Pb-Cu ores elsewhere in the world. Meteorite impact accentuated on-going ore forming processes and magmatism at Sudbury."

Jan 1, 1997

By M. Walmsley, D. Maynard

"This paper describes the use of terrain and soil information in the planning of mine developments, particularly in satisfying many of the existing provincial regulatory requirements. It is also noted that, if properly used, this will provide a solid data base for cost-efficient and environmentally acceptable land use.IntroductionIn planning the development or expansion of a new or existing mine, engineering alternatives are judged on many factors, one of which is the environmental influence. Ecological investigations, ensuring consideration of a rational approach to managing land use and environmental impacts, should be carried out prior to a final decision being made on mine development. The Pit Slope Manual (CANMET, 1976) suggests that both baseline aquatic and terrestrial data be collected and interpreted in such pre-mining surveys. In British Columbia, planning procedures now exist which incorporate biophysical studies to help identify, assess and manage major environmental impacts associated with mine development.Methods outlined in the Guidelines for Coal Development (E.L.U.C., 1976) have been successfully applied in recent years. Following this example, the Inspection and Engineering Division of the B.C. Mineral Resources Branch prepared guidelines to help expedite the development of new base metal mines (Procedures for Obtaining Approval for Metal Mine Development; Ministry of Energy, Mines and PetroleumResources, 1979).The metal-mine guidelines require the proponent of a new mine development project to prepare a two-stage assessment proposal which systematically moves from a preliminary feasibility study (Stage I) to a final project design (Stage II), including application for regulatory approvals. One purpose of the Stage I report is to provide a description of the existing environmental conditions that could be affected by the proposed development. A preliminary environmental impact assessment should also be reported. The Stage II report will contain detailed assessment and management of environmental impacts."

Jan 1, 1981

By T. W. Sullivan

"This paper explores the history of AC static variable frequency control drive systems on open cast mining machinery, in particular electric mining shovels and electric walking draglines, over the past ten years. It critiques the peformance of these drive systems from a productivity and operating cost standpoint and evaluates the over-all success of the original design concepts as they were envisaged in the 1970s. The paper details the state-of-the-art as it exists today as well as design improvements contemplated for the immediate future.IntroductionConsidering the fact that the very first successful application of an alternating current electrical distribution system occurred at the Gold King gold mine near Ames, Colorado, U.S.A., in the year 1891, it seems somewhat ironic that almost 100 years later, AC excavator drive systems are just now becoming commonplace in the mining industry.If one were to read the biography of Lucien L. Nunn, the first person to successfully install a commercially viable alternating current power distribution system, one would quickly visualize a parallelism between his fight to achieve acceptance of his new lower cost technology and that of those commissioned with the belief that AC static variable frequency control drive systems are not only a better performing, lower cost drive system for mining excavators today, but moreover, the drive systems of the future in our industry.This paper will deal with the evolution and incorporation of AC static drive systems on open cast mining excavators. It will trace the history of the development of these drive systems in the mining industry, the current state-of-the-art concerning these systems, and what the future holds for these excavators in our industry."

Jan 1, 1990

By S. Sopher, C. Barsotti

"Inco Gold Company was created in 1987 as an unincorporated business unit of Inco Limited. In 1988, Inco Gold Management Inc. was incorporated to supply management, exploration and engineering services to this unit. The first new project, at Casa Berardi, Quebec, was brought to production in September 1988, less than two years after completion of exploration. For 1989, Inco Gold&apos;s exploration and capital expenditures have been budgeted at approximately $94 million, a record level. Inco Gold holds interests in more than 80 precious metals ventures and prospects in Canada, the United States, Brazil, Indonesia, Papua New Guinea and France. The most advanced projects, in addition to Casa Berardi, are at Mineral Hill, Jardine, Montana, where initial production is anticipated in the third quarter of1989, and Crixas in central Brazil, where production is scheduled to begin during the fourth quarter of the same year.BackgroundTraditionally, Inco Limited&apos;s mineral exploration has concentrated on nickel and other base metals but since the early 1980s Inco&apos;s exploration activity has focussed strongly on precious metals, principally gold. As a result, three deposits have been discovered and developed . In order to accelerate the establishment of a strong gold mining enterprise with its own specific growth and profit objectives, Inco Gold Company was created in 1987 as an unincorporated business unit. At the end of 1988 Inco Gold&apos;s share of drill-indicated gold reserves was approximately 14 million short tons containing 3.4 million ounces of gold.At Casa Berardi in northwestern Quebec, one mine is in production and another is planned to open in 1990. Properties at Crixas in Brazil and at Jardine, Montana, U.S.A., were being readied for production in 1989. By 1991, Inco Gold&apos;s share of gold production is expected to be 125 000 ounces with a target of 400 000 ounces annually by the mid-1990s."

Jan 1, 1990

By G. S. Cole

By 2025, the U.S. automotive industry will have to average 54.5 mpg (4.3l/100km) Corporate Average Fuel Economy (CAFÉ). While new/improved powertrain technology (turbocharging, electrification, diesels, transmissions and stop/start) will be critical, it is estimated that 25-40% of the new CAFÉ standards will require significant mass reduction, and lightweight structural materials will be required. This presentation examines vehicle mass reduction based on new developments in manufacturing automotive structures and components using light metals (aluminum and magnesium), conventional heavy metals (iron and steel), polymers, and carbon-fiber reinforced polymer composites. Components that used to be sand cast or pressure die cast provided minimal fatigue strength and ductility. But greater mass reduction uses more light metals in structural applications. They require eliminating porosity and inclusions to improve ductility and fatigue strength. Improved casting processing, with vacuum die casting, counter pressure and squeeze casting, and new forging and extrusion applications are being developed for this purpose. New grades of ultra-high strength steels can be made thinner, and save over 1/3 the mass vs conventional mild steels. But more complex and expensive processing, such as hot stamping and in-mold quenching, is required. Most engine block structures have migrated from grey cast iron to aluminum over the past 40 years. But compacted graphite cast iron has higher strength at high combustion temperatures and pressures so that high powered engines can be smaller and even lighter than aluminum. Assembling a range of lightweight materials into vehicle structures requires specialized assembly techniques, including sophisticated structural adhesives that can mitigate vehicles’ unique corrosion environment. The presentation will conclude with discussing lightweighting strategies of Asian, American and, European marques and the materials, component designs and assembly techniques used to achieve 2025 CAFÉ.

Jan 1, 2016

By B. MohammadSadeghi, S. Bakhshivash, M. Haghshenas, F. Rahimi

"Spring-Back/Forward in sheet metals is defined as recovery of elastic strain upon unloading in a deformed sheet specimen. Since this phenomenon can cause alternation in the dimensions of a part, leading to irrecoverable compensations, the operative parameters need to be investigated, thoroughly. To assess spring-forward and effective bending parameters, V-shaped bending dies are the most commonly used experimental approach. In the present research, the effect of bending angle and punch tip radius on the spring-forward behavior of an Al-Mg-Si alloy sheet specimen is studied. To this end, a V-shaped die with four bending angles (i.e. 30°, 45°, 60°, and 90°) was designed and fabricated. Specimens with thickness of 2 mm were cut with dimensions of 50 mm×10 mm. Results show that by increasing the bending angle, the spring-forward angle decreases. In addition, smaller punch tip radiuses lead to further spring-forward. The effect of these parameters on the amount of spring-forward angle, strain distribution and homogeneity along sheet thickness was assessed using finite element analysis (FEA). Simulation results show that as the bending angle increases, the strain is developed more homogenously. Finally, micro-hardness test was used to study the effect of strain hardening caused by bending operation on strength evolution. Results show higher hardness trends for the zones in which the maximum plastic strain occurs.INTRODUCTIONPrecise production plays a significant role in the durability of a part. When it comes to sheet metal forming, this issue should be taken into account as an important factor. In order to predict the alternations, bending dies with special geometric parameters (i.e. V-shaped, U-shaped and L-shaped dies) are commonly used (Wagoner, Lim, & Lee, 2013)."

Jan 1, 2016

By Robert B. Wickham

"American Barrick has always balanced its aggressive operating approach with a conservative financial strategy. In fact, what enables their mining team to pursue such aggressive plans with confidence is the conservative financial strategy adhered to by the company. These policies are built on a prudent mix of gold linked financings, equity and gold price hedging.This paper outlines these policies and focusses in particular on American Barrick&apos;s gold price hedging program.IntroductionThe company&apos;s balance sheet at the end of 1990 clearly shows the wisdom of its conservative policies. Total assets have grown to over US$1 billion; cash has grown to US$312 million and shareholders&apos; equity to US$645 million. All amounts included in this paper are quoted in U.S. dollars. Increased gold production and an effective gold price hedging program also combined to produce record income from operations, earnings and cash flow in 1990.The first half of 1991 is also indicative of the benefits of the company&apos;s conservative financial policies. Increasing production, together with its comprehensive gold hedging program, has generated increased earnings, even in a period of falling gold prices.All year-over-year numbers for the first six months are up. Gold production was 36% higher; earnings of $40.2 million $ 0.30 per share - were 46% higher than 1990.Barricks revenue continued to increase despite gold prices remaining unchanged during 1990. Barrick&apos;s hedging policy protects the company from falling gold prices on the basis that the upside looks after itself. Their hedging program - including various goldlinked fmancings - enabled Barrick to realize an average price of $437 per ounce of gold sold in 1990, compared with the Comex average gold price for the year of $384 per ounce."

Jan 1, 1991