Search Documents

By Manula C. B

The total systems model for underground oal mining planning and design is a set of omputer programs which encompasses a realis- ic reproduction of the interaction between he geological, environmental, equipment, meth- ds and the health and safety aspects of the ining plan. The total system includes nine ajor subsystems - Geology and Reserves, Meth- ne Generator, Roof Support, Subsidence, Pro- uction, Rail Haulage, Cost, Water Generator, nd Ventilation. The subsystems themselves re divided into two categories based on the requency with which they are executed. Event riented Subsystems are executed either inde- endently, or at discrete intervals when cer- tain specific events occur. Dynamic subsystems 'unction interactively during the production :ycle. They transfer data to or request data `rom event oriented subsystems only when spe- ific events occur. Three specific areas for iodel application are in the measurement of system performance, the development of the '_ nterrelationships of the components of deep Wining process and the evaluation of new and Lnnovative mining technology.

Jan 1, 1977

By Sandy W

This paper examines the effects of a significant number of plant alterations and modifications to the lead flotation circuit during the past five years. Metallurgical effort is directed largely at the flotation performance of middling streams and current strategies are discussed. The automatic control of cell destination and collector additions are outlined in the latter section of the paper, along with a description of control hardware in current use.

Jan 1, 1983

By Thompson J

A programme of testing and evaluation has been in progress at Isa Mine for the last four years with the objectives of rationalising ground support practices, improving installation quality and increasing productivity of ground support functions.Numerous innovations have been successfully implemented. These include the introduction of swellex rockbolts as the major form of temporary support, the use of splitset rockbolts as the primary means of support for the hangingwalls of cut and fill stopes and the introduction of dowels with pumped cement for general long term support.The installation of swellex bolts has been successfully mechanised throughout the mine using Tamrock automatic rockbolters and Atlas Copco BUK 11R drilling rigs modified for this purpose.

Jan 1, 1985

By Dorricott M. G, McAllister J

This paper is concerned with the application of a probabilistic approach to the risk assessment of mining projects.In current practice, sensitivity analysis is the most commonly used deterministic approach of accounting for the uncertainties involved in mining project evaluation, while Monte Carlo simulation is considered to be the best probabilistic method available for the same purpose. The methodology of the approach proposed in this paper is as simple as that of sensitivity analysis. However, the results obtained can be more comprehensive than those obtained from Monte Carlo simulation. Various important statistical features, such as correlation and skewness, of the basic random parameters can be easily taken into account by the proposed approach. Example studies are demonstrated. Lotus 123 was employed for the associated probabilistic calculations.

Jan 1, 1992

By Reimer TH

The model described in this paper has been developed for and in close collaboration with the Bong Mining Company Ltd, Liberia/West Africa. When working an irregular deposit a de- tailed short term production schedule becomes necessary in order to ensure an equal and homo- genous concentrator feed. If the irregularity of the ore body exceeds a certain degree, blen- ding facilities have to be provided between the mine and the concentrator, but even then sche- duling of the mine production is inevitable to meet the given requirements of the blending bed and to keep these conditions steady for at least some of the successive periods. To assist the planning department in set- ting up optimal production schedules a computer model has been developed using a linear pro- gramming approach. The deposit is divided into equally shaped blocks containing defined quali- ties and quantities of ore and/or waste; from which one has to select those quantities of ore which will meet the requirements of the blen- ding bed. The objective function of the model

Jan 1, 1977

By P J. Mathew

Quality and process control in the iron ore industry is based on measurements of ore grade from blast holes through to shiploading. Traditionally this has been carried out using conventional sampling, sample preparation and analysis methods, but on-line analysers are now being introduced for monitoring the grade of important process streams. Once a conventional sample has been collected, it can be analysed for a wide range of elements. On the other hand, on-line analysers measure only a few selected elements, but they provide rapid feedback on grade, which is important for effective quality and process control. In both cases, the linkage between mining, processing and final blending operations at the port is crucial to ensuring that product quality is maintained while production targets are met and the life of the resource is maximised.

Jan 1, 1998

By Paine G

Kidston Gold Mines commenced mining in 1984 and currently mine approximately 10 million tonnes per annum of ore and waste using a conventional truck and shovel open pit method. The overall mine grade is a low 1.82 grams per tonne.The mineralisation is generally uniform within the ore zones and mining boundaries are staked out from blasthole assays according to pre-determined cut-off grades. Buffer blasting is necessary to minimise post-blast lateral movement of in-situ grade for digging control.The characteristics of the rock currently mined vary widely from soft oxidised to hard unweathered rocks. Blasting problems have been experienced during the initial mining phase in these harder rocks.

Jan 1, 1986

By J Sarvinis

The design and operational aspects of fluidised solids transfer-cooling devices will be discussed in this presentation. The devices include air slides and fluoseals (also called seal pots, loop seals, etc), which are widely used in metallurgical plants and other processing plants. Cooling can be achieved while solids are transported in the solids transfer devices. The units combining solids transfer and cooling provide compact and clean plant layouts and also reduce capital and operational costs. Fluidised devices provide excellent gas-to-solids and gas/solids-to-surface heat transfer rates, hence high cooling efficiency. Fluidising gas, such as air, nitrogen or other gases, can be used as direct cooling mediums. Coolants such as water, steam and other liquid or gas cooling fluids can be used as indirect cooling mediums via tube coils immersed in the fluidised solids. The fluidised transport devices share some common features with fluidised bed equipment. The air slide is similar to a linear fluidised bed while the fluoseal is similar to a circular fluidised bed. Therefore fluidised bed design techniques are applicable to the design of the air slides and fluoseals. The heat and mass balance and temperature profiles of the devices concerned will be discussed in the presentation. The design criteria and operational philosophies of the critical components such as tuyeres and air spargers will also be discussed.

Jan 1, 2006

By Wills BA, Barley RW

A brief description of viscosity measuring devices used in Dense Media Separation (DMS) plants is given, including a new On-line viscometer system. The various factors which affect suspension viscosity are identified. The effect of temperature variation on viscosity and viscosity measurement is examined in detail. Practical problems in using a modified Stormer viscometer for laboratory testwork are noted. Likely problems of continuous viscosity measurements are also discussed.

Jan 1, 1987

Most mineral products exported from Australia to Japan, with the notable exception of coal, are purchased with weight and quality determined on discharge. Sampling of imported minerals for purpose of payment is done at facilities owned and operated by the purchaser. The selling shipper is represented at the weighing, sampling and testing by an independent inspection group who supervises the whole procedure. Sampling and testing are done within the provisions of the contract between the two parties, and normally in accordance with the relevant Japanese Industrial Standards (JIS). These JIS specify such things as the number and mass of increments to be taken; the practice of taking these increments; the method of determination of moisture, size distribution and quality. The JIS concerned with sampling however, are meant to be basic guides rather than rigid rules. Hence sampling and testing practice varies from plant to plant. In general Japanese sampling facilities and methods are elaborate and efficient. Opportunity is given for the discussion of varying technical viewpoints between consumer and shipper. However the resolution of differences and the implementation of changes normally takes a long time. Such discussions seem best reduced by prior contract agreement on reasonable specifications and detailed testing methods. The independent inspectors

Jan 1, 1976

The Golden Cross is the first large precious metals mine to be both commissioned and closed in the æmodernÆ era in New Zealand. This paper discusses the life cycle of the Golden Cross mine, with emphasis on the closure process and post closure management.   The closure process has generally been very well managed, and successful, but in spite of that some on-going issues remain unresolved. Nearly nine years after the end of mining the mine owners are still actively managing the site, with no immediate end to that in sight.   The site has been described as atypical, due to the identification of a deep seated landslide below the tailings and waste rock storage facilities. However that should not be given too much emphasis when addressing the overall closure and post-closure management issues, which could well apply to other existing and future mine sites in New Zealand.   The Golden Cross can provide valuable lessons for other miners, and the issues arising at this site should be watched closely by the industry as a whole.

Jan 1, 2006

By Leigh G, Gottleb G, Wilkie G

The estimation of particle liberation is important in the study of mineral concentration. With simple systems, where the densities of the components are low, the liberation can be studied directly by density fractionation. For most practical systems, and particularly for the dense, complex sulphides, the only method known is by measurement in polished section. There are two major difficulties with such measurements. Firstly, the measurements themselves are difficult and considerable care is needed before reproducible results can be achieved. Secondly, a well known stereological problem arises which gives the estimates an inherent bias. The paper discusses both aspects of the problem. The practical features of measurement are treated in detail and a method described which has been developed and proven to give reproducible estimates of the liberation in the section. This discussion relates to automated measurements by QEM*SEM and presents a way of estimating the confidence limits within which measurements lie. Comparisons are shown between measurements made by the traditional manual optical technique and automated equipment. Stereological reconstruction is also discussed briefly. Several methods have been presented in the literature but all are complex and none is yet widely accepted. Area measurements are less biased than linear estimates so a practical approach is to use area measurements in uncorrected form. The topic is still being actively researched so it is expected that one method will soon emerge as the standard technique.

Jan 1, 1993

By Weimin F

In the last decade, great strides have been made in the raise boring technique in China. Extensively, the drilling and blasting method has been replaced by the mechanized raising method since 1980. There are now over 3C raise drills operating in more than 20 mines. The diameters for shaft boring varies from 500mm to 2000mm, and to depths up to 90m. Tlis paper mainly describes the performance, mtLin technical achievments and applications of all four kinds of raise drills, and auxiliary equipment. Finally, some recommend- ations for future improvement in the raise boring technique are presented also.

Jan 1, 1987

By Han Kook-Nam, Lawson F

The recoveries of the three cobalt minerals in the Mount Cobalt deposit, cobaltite CoAsS, erythrite CO3(AS04)8H20, and new cobalt mineral with a composition approximating 2CoO.CaO.Fe203.2As205.11H2O were investigated using physical and surface-chemical processes.Over 80 per cent cobalt recovery was achieved by tabling a cobaltite-mineralized sample, while about 76 per cent cobalt recovery was obtained by dry feed magnetic separation of a sample containing erythrite and the new cobalt mineral. The resultant primary magnetic concentrate with a cobalt grade of 5.5 per cent, was able to be upgraded to 14.4 per cent cobalt by regrinding .and a further magnetic separation.Electrophoretic mobility - pH responses for each of the three cobalt minerals were found to be similar. Each mineral remained negative over the pH range 3 to 11 and was most negative at mildly alkaline pH values.Cobaltite was floated effectively with amyl and ethyl xanthate collectors under acidic conditions at collector concentrations of 10-2M to 10-5M. Erythrite showed a similar flotation response using 10-sM amyl xanthate. The practical application of these laboratory separations to an industrial process is suggested.

Jan 1, 1976

For the purpose of this paper the Otago Region is that covered by the Otago Regional Council. This area, like other South Island Regions, has a river system starting in the Mountains and are all gravel bed rivers. The gravel from these rivers has been the major source of aggregate in the region since the development of the province began. The majority of the aggregate is a mix of greywacke, schist and quartz, which will be referred to later with its production problems. The region has been broken down into various areas.

Jan 1, 1992

By R Barrette, V Lawson

Over the last year at Clarabelle Mill, three circuit reconfigurations were implemented. One circuit reconfiguration, æA CleaningÆ, was initiated due to a furnace failure at the smelter complex, and two of the circuit reconfigurations, æincreased copper (Cu) separationÆ and the æInterim IsaMillÖ circuitÆ, were seen as opportunities to increase cash flow through the mill. A Cleaning and the Interim IsaMillÖ circuit took advantage of engineering design already completed for a major capital project. The engineering for each was modified, as needed, and construction of the required portions of the capital project was fast tracked. The increased Cu separation circuit change used existing test and plant equipment to increase the plant Cu concentrate production. Implementation of the projects required teams that included operations, maintenance, technical support, project management and capital project resources. This paper discusses the business reasons driving the changes and the forethought or synergies with other work, which made them a success, and what was learned through each project. CITATION:Taylor, A, Lawson, V and Barrette, R, 2012. Responding to the challenge - Necessity driving circuit change, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 247-254 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Dorricott M. G

Ballarat Goldfields NL is developing an exploration decline at Ballarat East using a Mitsui Miike S-125 roadheader. To-date, 530 in of advance has been achieved at an average rate of 16.1 m/week. Roadheader availability has averaged 94.3 per cent, and pick consumption has averaged 0.016 per m. Ground support has involved pattern rockbolting with split sets, 100 mm thick fibre reinforced shotcrete, and steel sets as required. The slower than expected advance rate has mainly been due to difficult ground conditions. It is expected that a further 970 in of decline will be mechanically excavated before a drill and blast system becomes more economical.

Jan 1, 1995

Alcoa of Australia's Western Australian bauxite mining operations in the Darling Ranges, southeast of Perth, present major challenges in the control of air blast. The close proximity of rural communities and the face profile make the traditional methods of air blast control difficult.An extensive blast noise monitoring programme has been established. The development of a computerised blast noise prediction model and the establishment of a radiosonde weather balloon facility have reduced blast induced complaints by a factor of ten.The meteorological factors affecting blast noise transmission are discussed and examples are given of adverse weather conditions for the southwest region of Western Australia.

Jan 1, 1983

In the first half of this century a mining industry was developed in Indonesia under Dutch colonial rule. World War II and the subsequent struggle for independence resulted in the destruction of most of the infras- tructure and much of the data. After independence, restrictions on for- eign investment and internal turmoil prevented re-establishment of a viable mining industry until the formation of the present Government after 1965 and the enactment of sound laws in 1967 to encourage foreign investment. Rebirth of the mining industry was followed initially by slow growth, but in the 1980's, spurred by the worldwide interest in gold, Indonesia has become the focus of an intense exploration boom for gold and other precious metals. 103 Contracts of Work for gold have been awarded since 1985 with Australian companies being the most predominant. Since 1985 three new gold operations have been commissioned and another two are nearing completion. Several more are undergoing feasi- bility studies. There is reason to predict that Indonesian gold produc- tion will grow to place the country in the ranks of significant producers during the 1990's.

Jan 1, 1988

By Boyce WH

Earthquakes are the most frightening and devastating natural phenomena known to mankind. They strike without warning and their consequences can be disastrous in terms of the toll of human life, financial crises related to the damage or destruction of man-made structures and the social and economic effects on a wide spectrum of the affected communities in the aftermath of the event. Such situations can be widely attested to by most areas around the Pacific Rim. Indeed, the threat of earthquakes is always imminent because of the geological-tectonic nature of the region as manifested by past experiences. It is patently obvious that earthquake occurrences are not only a geological hazard but also pose a serious social danger. When one considers the 19 September 1985 Mexico (Michoacan) earthquake (Mitchell at al., 1986), the necessity of continuing research is of paramount importance. An estimation . of earthquake risk encompasses both qualitative and quantitative aspects and demands a multidisciplinary research effort integrating seismology, tectonics, geology, enginering, sociology, economics, insurance and governmental policies (Bolt, 1978; Booth, 1984). These roles in mitigating such a hazard have been aptly discussed by Press (1985). A series of discussion papers based on an intergovernmental conference covering the whole scenario were published by UNESCO (1978). A comprehensive case history was provided through a workshop on the 1886

Jan 1, 1987