Search Documents

In recent years the use of directional drilling has become increasingly popular in several applications. These include shaft pilot holes, exploration drilling, mine service holes and drilling beneath surface structures and obstacles. The prime objectives are to increase accuracy and reduce time, cost and environmental disturbance.

Jan 1, 1992

The Oregon-Idaho graben evolved after widespread Uwleiitic flood basalt volcanism associated with the arrival of the plume head of the Yellowstone hotspot beneath southeastern Oregon approximately 17-16 Ma. The north- to north- northeast-trending, 50 km-wide graben evolved between 15.5 and 10.5 Ma during east-west extension. The graben is part of a middle Miocene back-arc rift (1,100 km long) that includes the northern Nevada rift, the Baker and LaGrande grabens, and the Chief Joseph dike swarm of the Columbia River Basalt Group. The graben ceased to be a volcano- tectonic depression as the cross-cutting western Snake River plain began to evolve at approximately 10.5 Ma.

Jan 1, 1995

By Hashimoto H, Arai Y, Sikong L

For utilization of solid carbonaceous materials produced in processes of cracking heavy oil, such as petroleum pitch, as powder fuel, it is necessary to develop a process for fine grinding of these materials. It is known that grinding' additives are effective for fine grinding of cohesive and heat-sensitive materials such as petroleum pitch, therefore in this study, effective methods for fine grinding of petroleum pitch with some grinding additives were investigated. Experiments were carried out by using comminution kinetics based on mass balance. From the results of the investigation by using a batch ball mill, it was found that sodium stearate, calcium stearate and carbon black were effective additives for the improvement of grinding efficiency. Optimum concentration of the grinding additives was also found to give a required particle size of products. Concerning to the action mechanism of these additives, it is considered that the additives which adhired to, or were absorbed on the surface of petroleum pitch particles not only prevented cohesion of the particles but improved dispersion of the particles as well. From the results of the investigation by using a laboratory screen mill which is a representative built-in classifiered impact crusher, carbon black was found to be an effective additive for the improvement of grinding efficiency and mill performance. It is also considered that the improvement of classification efficiency by carbon black affected the mill performance.

Jan 1, 1987

By Rivers CJ

The Brolga deposit is a Ni-Co enriched laterite, formed over intensly serpentinised peridotites of the Marlborough Block. Basement lithologies at Brolga consist predominantly of serpentinised dunite, with lesser massive serpentinite shear, gabbro and harzburgite. Investigation of the deposit has defined 17 different varieties of saprolite, ferralite (limonite), and ferricrete. Different combinations of these varieties form three distinct lateritic associations, the Hard, Soft and Dyke Associations. Recognition of key textural and mineralogical features in each association, an understanding of basement geology, and an awareness of current climatic conditions, suggest that: 1. both the Hard and Soft Associations have formed under relatively dry climatic conditions; 2. the Soft Association reflects much poorer groundwater drainage than the Hard Association; and 3. the Dyke Association has formed from a gabbroic basement, and has also been affected by restricted groundwater drainage, caused by poorly permeable marginal serpentinite shears.

Jan 1, 1996

By Kershaw M. G, Maughan R. C A

A process for eliminating nickel from electrolytic zinc plant solutions by precipita- tion with dimethylglyoxime (DMG) was developed to enable the Electrolytic Zinc Company of Australasia Limited (EZ) to treat nickel-bearing zinc dust precipitates. These precipitates are leached to recover their Cd and Zn content. The final Zn bearing solutions contain relatively high Ni concentra- tions (20-100 mg/1) and are treated with DMG and then neutralized to pH 4.6-4.8. The pre- cipitate is filtered off and the solution returned to circuit. DMG consumption is about 200% of theo- retical requirement, and Ni removal is 80% complete overall.

Jan 1, 1977

Among the various methods of thick-seam mining already well-tried in practice longwall caving with extraction of a single slice, as thick as possible, abandoning the top and/or the bottom coal, seems to be the most suitable one for the Australian coal mining industry. The production units of the future should be equipped with heavy double-drum shearer-loaders, wide armoured conveyors, (with one or two central chains) and shield support. Material of this type has been developed for seams up to 6 m thick. Output figures of more than 6,000 tROM/d from a single face can be looked upon as a quite realistic expectation. The problems of co-ordinating such large production units with the whole layout of the mine are discussed. The factors to be taken into account in the planning work and for preven- tion of mine fires caused by spon- taneous combustion are dealt with. For economic reasons the highest possible utilization factor of the very expensive equipment must be aimed at. Furthermore, the seams or parts of seams to be extracted should be carefully selected.

Jan 1, 1976

By Fukuda M, Kurita K

A mathematical model for estimating the liquid level in the hearth is presented. The analytical result was checked on a cold two-dimensional model and an additional boundary condition for the fundamental equation resulted. The applicability of the resultant equation was investigated on a cold model and a regression equation obtained for the average liquid level for Kashima No. 1 BF. Comparison of calculated and observed results were in fairly good agreement. It is concluded that the liquid level in the commercial furnace can be calculated from the measured values of pressure in the bosh and operating conditions.

Jan 1, 1975

In the future to excavate sufficient coal for power generation, two dredgers would be required to dig overburden or interseam 70010 of the time and three dredgers 40010 of the time. One overburden system was not adequate for this requirement, making coal production reliability vulnerable. TS5 spreader is the new machine element of this system. The selection of the best type of machine configuration to suit the application was then subject to an internal SECV VE Study, a registration of interest and a tender for two machine alternatives. This paper outlines the reasons why SECV planned the Secondary Overburden System and how the Krupp machine met these requirements. It also identifies the main design features of the machine and its constructability which will allow the machine to be operational by the end of May, 1990.

Jan 1, 1989

By Simpson JF, Murrie SJ

In determining new areas for slag disposal a foamed slag aggregate has been developed for use as a skid resistant material. The foaming of the slag does not rely on the use of water, but rather on the slag chemistry. Laboratory test results indicated that a product having good skid resistant properties has been prod- uced. A section of road is being assessed for performance of the aggregate in a surface dressing application under heavy load. The results from the test section after seven months have shown that the foamed slag is suitable for this application. Further test sections are now being considered.

Jan 1, 1979

Key blocks occur on the surface of excavations and on the walls of the ornamental stones and limestone quarries due to the formation of joint planes, fissures, microfaults and quarrying operations. Movements of these key blocks have produced numerous important failures and are responsible for routine overbreak and rock falls accounting for great costs. The thrust of this work is to demonstrate how to delimit zones of poten- tial key blocks (danger zones) in the wall of Bani-Khalid quarry of lime- stone by using the block theory technique (stereographic projection). The final result of this study indicated that, there are three potential key blocks, the most critical one has been determined. To treat the problem, we sug- gest either to provide timely support to prevent the movement of this block, or to analyze it further in hopes that available friction on the faces will hold it safely in place.

Jan 1, 1989

The granitoid rocks in Burma can be subdivided into three main belts viz. (1) Eastern Granitoid Belt, (2) W-Sn related, Central Granitoid Belt and (3) Porphyry Cu (Au)-related, Western Granitoid Belt. The W-Sn related, central belt Granitoids were interpreted to have generated during the continent-arc collision and the Porphyry Cu(Au)-related, western grantioid belt was emplaced in a magmatic-volcanic arc above an east-dipping subduction zone. INTRODUCTION Major tectonic domains of Burma Burma region can be subdivided into N-S trending (6) major tectonic domains from west to east (1) Arakan Coastal Strip as ensimatic Foredeep (2) Indo-Burman Ranges as Outer Arc or Fore Arc (3) Western Inner-Burman Tertiary Basin as Inter-Arc Basin (4) Central Volcanic Belt (Central Volcanic Line) as Inner Magmatic-volcanic Arc (5) Eastern Inner-Burman Tertiary Basin as Back-Arc Basin and (6) Shan-Tennasserim Massif as ensialic, Sino-Burman Ranges (Bender, 1983). The Sagaing (transform) Fault and Shan Boundary Fault form as a tectonically significant boundary between Eastern-Burman Basin (Back-Arc Basin) and continental,

Jan 1, 1987

By Williams ID

Ore and coke of various size fractions (1 to 11 mm) were packed in a column (146 ó) and resistance to air flow measured under a range of conditions. Results have shown that layered charging results in an interface having essentially a directional structure the thickness of which is directly proportional to the coke and ore size ratio and whose flow resistance exceeds that of the coke layer many times its thickness. Friction factor - Reynolds number plots showed large positive departure from the Ergun equation for all components investigated whilst functional analysis and that in terms of bed constants, showed a strong dependency of the pressure gradient on bed properties and the actual particle size as well as the size ratio. It is also shown that pressure gradient in mixed beds follows previously reported behaviour and that a directional interface offers higher resistance to flow than a mixed interface having the same volumetric ore/coke ratio. Significance of results to practice is discussed.

Jan 1, 1975

A narrow (200-300m) zone of amphibolite facies metamorphic rocks underlies the Papuan ophiolite near the Musa-Kumusi divide, SW of Popondetta, Oro Province. The amphibolite rocks are bounded up-section, to the NE, by peridotite and gabbro of the ophiolite; and down-section, to the SW, by mafic greenschist, which in turn overlies blueschist facies mafic schists of the Emo Metamorphics.Amphibole compositions within the narrow contact zone show a strong chemical zonation which reflects a steep thermal gradient, with maximum temperatures >800¦C at the peridotite contact. The zonation is recorded in Ti content and A-site occupancy, relative to Al'¦

Jan 1, 1994

By Yianatos J. B

The advances in the study of control alternatives for flotation columns are reviewed. An integral solution to the control problem has to deal with problems associated with instrumentation, process modelling, control strategies and control algorithms. The term hierarchical control is used here to mean the intelligent integration of available knowledge, control algorithms and logic rules of decision. The selection of information, algorithms and rules is based on the experimental and theoretical knowledge of the column flotation process. The software support was designed and implemented in object oriented computer programs. This technique allowed the implementation of a combination of control techniques, algorithmics and heuristics, in the form of a control strategy. This strategy has shown to fit well with processes exhibiting complex dynamic characteristics. The hierarchical control was implemented in a pilot column and included the following general aspects: co-ordination of distributed conventional control loops, use of sets of control parameters for the froth depth control loop according to the froth depth state, verification and diagnosis of sensors, on-line predictive estimation of gas hold-up, diagnosis of common operating problems and the use of predictive control to account for feed flowrate changes.

Jan 1, 1995

By Fletcher A. E W

Ever since it made its debut in 1962, in the form of a Robbins 31R, the raiseborer has become an accepted tool in the mining and civil construction industries. The first raiseborer to be used in the Witwatersrand goldfields made its appearance in 1968. This was a Robbins 42R which could raisebore 185m deep holes to 1,22m diameter. From 1968 to 1973 capability increased with the introduction of first the 61R, then the 71R and finally the 83R, which could raisebore 610m deep holes to 3,66m diameter. This created a demand for larger holes but the cost of bigger, more powerful machines requiring larger, stronger drill pipe, cutters and other accessories was prohibitive. To avoid replacing existing models such as the 71R, and in order to increase their capability, the concept of reaming in two stages sequentially was developed jointly by a German drilling equipment manufacturer, Wirth, their South African subsidiary, Transbor, and a local contractor, Rocbor Raiseboring and Mining Contractors. The result, the Sequential Reaming Head, proved most successful and existing machines, normally limited to 2,44m diameter holes, could now ream to 3,66m diameter. This created a demand for even larger holes. In order to maximise the use of the sequential reaming head to meet this demand the HG330, and subsequently the HG330SP raiseborer were developed. Using a 4,26m/6,02m cutting head, these machines have raisebored holes 1000m deep in hard rock. The raise- boring of the first major hole to be excavated by this combination, the 484m deep x 6,02m diameter surface shaft at Premier Mine is described. Reference is also made to six other shafts which have been completed or are under construction.

Jan 1, 1987

By Lang SC

The Broken River Province, in the northern part of the Tasman Orogen, is divided into the Camel Creek and Graveyard Creek Subprovinces. In the Late Cambrian to Early Ordovician, and again in the Late Ordovician, the northern part of the Tasman Orogen was probably a convergent margin with calc-alkaline volcanism. These episodes may have been separated by a passive phase in which quartz-rich flysch and tholeiitic volcanic rocks were deposited. Subsequently, in the Silurian, the region underwent extension forming a large turbidite basin which included the Camel Creek Subprovince and the Hodgkinson Province to the north. Melange is pervasive in the Camel Creek Subprovince which was folded twice in the Devonian. The melange may be related to thrusting accompanying D1. No rocks younger than Early Devonian have been recognised whereas, in the Hodgkinson Province, deposition continued until the latest Devonian. The Graveyard Creek Subprovince formed adjacent to the Camel Creek Subprovince, probably as a pull-apart basin on stable crust. The deformation history of the Graveyard Creek Subprovince contrasts markedly with that of both the Hodgkinson Province and Camel Creek Subprovince. In the Graveyard Creek Subprovince, melange is only present in Early Ordovician rocks. No major angular unconformities have been recognised in the overlying marine to non-marine sequence, which ranges from Early Silurian to Early Carboniferous. Several hiatuses and a slight angular unconformity, all within the Devonian, may be related to the major events in the Camel Creek Subprovince. A major deformation in the Graveyard Creek Subprovince in the Early Carboniferous had only slight effects in the Camel Creek Subprovince. Movement on the Clarke River Fault was probably an important influence on sedimentation and deformation in the Broken River Province.

Jan 1, 1990

By Dugan K. J

Mine operators are currently in a situation where market forces are acting to reduce profit margins and at the same time, regulatory bodies are insisting on improved mine safety and stability. This means that ground support must be made more cost efficient while maximising operator and equipment safety.A key aspect of ground support efficiency is the 'in the ground' performance. This paper discusses the factors that influence the way rock bolts and cable bolts perform. It highlights the need to know how support efficiency varies in different ground conditions.

Jan 1, 1992

By Whiten WJ

Although cone classifiers have received little attention in the modelling of mineral processing units they are one of the oldest non-mechanical classifiers. Their use has enjoyed a revival in recent years because of their low cost of installation and operation. In this paper the development of models for cone classifiers is reviewed and a new model is proposed. The experimental work, data collection and analysis are briefly described, and the new model is presented and discussed. The data used in the model development are made up from three distinct experiments using different units in each case. There are 21 data sets from a 3 m cone treating the tailings in a copper concentrator, 24 data sets from a 0.3 m pilot-scale cone, and 29 data sets from a laboratory glass funnel (0.(Y73 m diameter) used as a cone classifier, giving a total of 74 data sets. The model structure was developed from an analysis of particle settling in classifiers, using specialised model building software. The size of a particle settling in a separator and the forced flow through the apex of the cone were related via hydrodynamic dimensionless groups to the operating conditions of the unit. The model predicts the separation efficiency using the following four parameters: efficiency curve shape factor, cut-point, underflow density (per cent solids) or underflow pulp velocity. The model covers a range of feed flowrates from 1.2 to 5000 1/min.

Jan 1, 1993

By Hendrix J. L, Nelson J. H

A study was conducted to examine how pretreatment of carbon-bearing gold ores with chlorine enhances gold recovery by cyanidation. It is hypothesized that metal species (including iron and copper) dissolved during chlorination adsorb on the carbon surface hindering the adsorption of dissolved gold. To test the hypothesis, samples of several sulfide minerals were subjected to reaction with sparged chlorine gas to determine which, if any, dissolve faster than gold under these conditions. Then, a synthetic carbonaceous refractory gold ore containing pyrite, chalcocite, activated carbon, and gold was subjected to gas sparging. The results of these experiments showed that chalcocite and arsenopyrite dissolve so that metal (copper and iron) is put into solution slightly faster than gold under the same chlorination conditions. Also, it was observed from the experiments that gold adsorbs on activated carbon during chlorination, but is replaced by copper and iron as the chlorination process dissolves more of the chalcocite and pyrite. The study concluded by investigating ferric chloride addition prior to chlorination to hinder gold adsorption on activated carbon.

Jan 1, 1991

By Clarici E, Marsden J. R, Calderbank P. A

Evaluation of previous studies of multi-layer perceptron type artificial neural networks in the modelling of the deformability behaviour of rock have suggested that a deviation from the standard method of laboratory testing of rock under triaxial loading at constant confining stresses and constant axial strain rates may be inappropriate when the data produced are used to train an artificial neural network. In this paper, preliminary results of adopting such a strategy are reported. Of specific concern is the establishment of a suitable schedule for the stress path during testing. Furthermore, the training element of back propagation optimisation was directed towards prediction of new stresses given old stresses and old strain increments. Adoption of this method of supervisation in artificial neural network training facilitates the integration of the trained neural network within existing numerical methods used in rock mechanics. The target code was a finite difference Lagrangian formulation for the analysis of continua. Sandstone rock taken from a quarry in the UK was used in the study which showed that the method has great potential.

Jan 1, 1995