Search Documents

By J R. Kyle

The Deep Mill Level Zone (DMLZ) skarn Cu-Au deposit is the deepest explored part of the Ertsberg East Skarn System extending from the surface at 4200 m elevation to the DMLZ at 2900 to 2600 m. The DMLZ is hosted in an upper Cretaceous to lower Tertiary siliciclastic and carbonate succession adjacent to the 3 Ma Ertsberg pluton. Much of the DMLZ ore is hosted by mixed assemblages of siliciclastic and dolomitised carbonate strata that have been altered to Mg-rich skarn assemblages. Unaltered equivalent strata from a 300 m cored interval in the Yellow Valley Syncline were characterised petrographically and representative samples were analysed for major element compositions. These stratigraphic and chemical units are interpreted to be responsible for the varying skarn lithologies within the DMLZ. The dominant prograde skarn assemblages are controlled by protolith composition, notably the relative abundance of quartz, dolomite, and calcite within the protolith. Models based on isochemical metamorphism of mixed assemblages of quartz and dolomite suggest that the formation of the forsterite-diopside dominant skarn assemblages resulted in the greatest amount of pore space increase. DMLZ Cu-Au concentrations were locally controlled by host lithology, with structural features providing fluid pathways that focused the mineralising fluids. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Based on a principle developed at a South African Mine, the CSIR developed a device with which the alignment of guide rails in mine shafts could be measured. Originally the technique could only be used to obtain guide misalignment values at the bunton sets. At the time this was considered adequate since it was assumed that guide realignment could only be done at the support points anyway. The technology was developed further and now it is possible to obtain æcontinuousÆ guide profiles from the measurements. Software was developed with which a guide realignment schedule can be drafted and the shape of the realigned guides can be predicted. A measuring system based on this technology is being used to conduct guide alignment measurements in shafts. The data is then analysed and a realignment schedule is recommended in consultation with the mine. Such a schedule may be prioritised so that the worst sections in the shaft are dealt with first. The measurement hardware and analysis software are described. Examples are presented that illustrate the principles and highlight measurement errors. A case study illustrates measurements recorded in a newly equipped shaft. A repeat measurement, 18 months later, shows the effect of recommended realignment as well as the change in guide alignment over this period.

Jan 1, 2005

This is a welcome opportunity to exchange ideas about educating for a profession in mining and metallurgy, and I shall use it to highlight the ways in which educators, the industry, and the profession can help one another make that educa- tion better. This is home ground for me in more ways than one. As the executive head of a uni- versity perhaps I may speak as an educator; and there is still, I hope, enough of the metallurgist in me to allow me to speak of what we metal- lurgists and mining engineers can do to help the educators. Another interest should be declared, too. Among the educating agencies I shall focus on universities; among universities I shall further focus on my own, the University of New South Wales. I know it best; and, more to the point, we are one of the minority that offer a full profes- sional training in mining and metallurgy. Further, we are as a university very much concerned- more than most-with specifically professional education, and especially with education in the professions based on science and technology. Mining and metallurgy have of course played a central role, from earliest times onwards, in the history and development of science and tech- nology. In that role they have been both pro- ducers and consumers of new knowledge. Indeed the whole new attitude to knowledge that began to spread in 16th and 17th century Europe owed a great deal to the interests and traditions of the miner and the metallurgist. The first modern text- book of mining and metallurgy, George Agricola's De Re Metallica, is very much more than a spec- ialist handbook; it is a major landmark in intel- lectual and cultural history.

Jan 1, 1978

This paper deals briefly with the geology and mineralisation of the Ediacara Mineral Field, which is located about 300 miles north of Adelaide in the Mount James Range.The field was discovered sane time prior to 1872. Total recorded production for the field amounts to a few hundred tons of lead and 36 tons of copper. Re-listing of the field during 1961-62 led to its classification as a Mississippi Valley type deposit. Diamond drilling has partly outlined the spread of mineralisation and confirmed its stratiform distribution,Sources for the metals are suggested and various possible mechanisms. of deposition are described.

Jan 1, 1963

In the early ages man contented himself with the use of such tools and appliances as would assist him in the enlightenment of his labours. With the advancement of science, numerous motives, with modifications and adaptations, have been introduced to enlighten labours, and in many cases have taken the place of man, but it can hardly be said that this applies to shovels, although one of the oldest implements of labour; certainly, with the introduction of the steam shovel the labours of man have been considerably reduced, but the hand shovel of today is used similarly to that of years ago.If the principle of the hand shovel has not been improved upon, it must not be suggested that the manufacturers of this article are not endeavouring to improve its quality, and the main point with which the manufacturers have to contend is the production of an article which will give a maximum of durability combined with a minimum of lightness. In order to accomplish this they must select suitable material, and subject it to such heat treatment process that will produce a shovel having a maximum of hardness and toughness without being unduly brittle, and which will withstand the excessive wear to which it is subjected.In this article an endeavour will be made to explain (a) the manufacture of shovels; (b) the defects commonly met with-the cause of same and measures which are necessary to remedy them.Before doing so a brief description will be given of the class of steel used for shovels; this is an important factor, and a steel which is admirably suitable is a plain carbon one containing approximately 55 - 70% C., and closely resembles that used for the manufacture of railway rails. This plain carbon steel is very extensively used, although at present alloy steels are being utilised to a certain extent for shovel manufacture, and with suitable heat-treatment.

Jan 1, 1926

The Mineral Research Centre is located at Perth in the suburb of Waterford, adjacent to Curtin University of Technology and within a Technology Precinct which includes Technology Park. The Centre, constructed by the WA Government at a cost of $16 million and occupied in late-1994, comprises three separate buildings housing the CSIRO Division of Minerals, Curtin University's School of Chemical Engineering and the Mineral Processing Laboratory of the Department of Minerals and Energy. The emphasis on R&D at the Centre is primarily in hydrometallurgy as a result of staff expertise, extensive bench and pilot-scale facilities, track record with the industry and, very importantly, two of the occupiers being partners in the AJ Parker Cooperative Research Centre for Hydrometallurgy. Staff in the Centre have a long involvement with R&D agencies such as AMIRA and MERIWA. The hydrometallurgical focus of the Centre complements that of pyrometallurgy at the GK Williams CRC in Melbourne and the Centre for Mining Technology and Equipment in Brisbane, to ensure that the mineral processing industry in Australia has access to a complete range of expertise and facilities to serve its needs.

Jan 1, 1996

By Morandini AF, Occella E, Clerici C, Mancini R

This contribution presents the first results of an experimental research aimed at finding an unified description of the first stages of a rock comminution process. With reference to the case of the jaw crushers and to the specific subject of the comminution law, the tests reviewed and analysed in this contribution have been carried out, at a laboratory scale, on five different materials (limestones, quartzite, serpentinite) at different reduction ratios and feed rates, and accurately recording both total power and idle running power. The analysis of the results has shown that: ò the grain size distribution of the products complies with a modified form of the Rosin-Rammler equation, already found to be well suited to representing the grain size distribution of blasted rock in previous works by the authors; ò observed trends of the consumed power at increasing reduction ratios is steeper than predicted by the classical Rittinger, Kick and Bond laws, Rittinger law representing however a closer approximation of the experimental results; and ò a more accurate description of the experimental results is provided by a modified form of the Rittinger law. Accuracy of the semi-empirical expression has been found to be usually better than ten per cent by comparing actual results with expected Results.

Jan 1, 1993

By Eupene GS

The valuation of exploration properties which contain no identified resources or reserves is the most subjective of all valuation tasks likely to be carried out by a geologist. The geoscience rating method proposed by Kilburn (1990) recognises this inherent subjectivity but also attempts to apply some discipline to the valuation process. Some other methods used for valuations of this type clearly lack discipline and are open to misuse and abuse. The Kilburn method essentially requires the practitioner to justify all aspects of the valuation process. The valuer must specify and, more importantly, quantify aspects which enhance or downgrade the intrinsic value of each property. The intrinsic value is called the ""base acquisition cost"" (BAC) and it represents the average cost to identify, apply for and retain a base unit of area of title. The BAC and base unit of area both vary with different types of exploration and mining title but remain constant for similar types of titles in the same mineral tenure regime. In the Kilburn Method the enhancement/ downgrading factors are determined by the geotechnical prospectivity (Kilburn Method) within the title. A modified version of the Kilburn Method presented here (""Modified Kilburn Method"") also focuses attention on other real variables besides the geotechnical attributes which influence valuations of this type, viz., competition for tenure and activity in the markets in which the exploration properties are being traded. The most active such market at present is the stock market. By utilising uniform BACs and base units of area (for similar titles) for all exploration properties (in practice in Australia this is only possible within a particular State or Territory), the method exposes the valuer's opinions of each of these variables to the scrutiny of the investor. The investor (or his professional adviser) is afforded the opportunity to directly compare valuations on different properties by different practitioners and can assess how the final valuation is weighted in respect of geotechnical prospectivity, competition for tenure, and stock/financial market sentiment. No other method currently employed in Australia to value mineral exploration properties affords the investor this `luxury', which some may argue is their right.

Jan 1, 1994

Minerals similar to the indicator minerals used in kimberlite exploration are widespread in the Cainozoic alkali basalts of north Queensland. Magnesian ilmenite, pyrope garnet, chrome diopside, chrome spinel, phlogopite and zircon were recovered from most of the localities examined. The occurrence of these minerals creates significant problems when indicator minerals are used for diamond exploration. Basaltic ilmenite is visually similar to kimberlitic ilmenite. Untransported grains are rounded and have pitted surfaces. Basaltic ilmenite grains often have exsolution lamellae and reaction rims of titanomagnetite. Although kimberlitic and basaltic ilmenite are chemically similar, basaltic ilmenite grains are usually less magnesian than their kimberlitic counterparts. Basaltic ilmenite contains very little Cr203. Pyrope garnet occurs as megacrysts and in a variety of xenolith lithologies in north Queensland basalts. Most basaltic garnet is Cr-poor and comparable with kimberlitic garnet from Groups 3 and 5 of Dawson and Stephens (1975). Wine-purple, chrome-bearing garnet is common in kimberlite but rare in basalt.

Jan 1, 1984

The issue of flyrock is critical to the operation of all mineral extraction sites that use blasting. This paper takes a risk-based approach to identifying, analysing and managing the flyrock hazard. The basic cause of flyrock generation is a mismatch between the energy available and the work to be done. It should be noted that the energy available depends on the charge confinement. This mismatch can be caused by an abrupt decrease in rock resistance (geological weaknesses), overcharging, inadequate delays between holes and rows, inappropriate blast design and inaccurate drilling. The mismatch can come about from two sides; either too much energy (charge) for a fixed burden (work to be done), or insufficient burden (work to be done) for a fixed charge. The main mechanisms of flyrock generation are rifling, cratering, face bursting and secondary blasting. Each source mechanism has different characteristics in terms of vulnerable locations and each requires different control measures. However, all controls require a high level of quality control and assurance. A range of different approaches for managing flyrock risk and determining blast clearance zone dimensions are presented. A prescriptive consequence-based approach is discussed. A conventional risk matrix based approach is outlined with some innovation regarding controls rating and uncertainty ratings. A published semi-empirical approach is discussed. Two examples of quantitative flyrock risk analysis are presented; one involves bench blasting based on a published paper and the second is a cratering example developed by the author based on consulting projects. Finally, a stochastic approach based on published work is presented which simulates cratering superimposed on face bursting mechanisms. Also, a stochastic analysis undertaken by the author of the cratering example is presented. Effective blast emission management is required for two reasons; firstly to reduce and/or eliminate safety risks and secondly to manage public perception of blasting risks such as flyrock. The conclusion of the current research is that the wild flyrock risk can be estimated using existing techniques. Furthermore, both qualitative and quantitative risk management methods as discussed in this paper can be used for flyrock management for a given blasting situation. A combination of both is considered to be best practice.

Jan 1, 2007

By D V. Boger

The use of chemical additives to initiate such processes as particulate separation through flotation or dewatering through flocculation, is common in the mining industry. The dosing of additives is none the less poorly controlled from a process control viewpoint and it is perhaps fortuitous that over-dosing or misuse of chemicals is rarely catastrophic to the production cycle. In many cases, such events would go undetected if it were not for economic considerations. Recently, the advent of orebodies with finer mineral disseminations and the push for greater efficiencies in both production and tailing disposal have resulted in the need for greater control of the dosing and utilisation of chemical additives. The need to grind at higher pulp densities and to finer sizes and to dewater to higher solid contents are but two examples that require a more stringent understanding of the true role of additives in controlling the rheology of suspensions and the influence of additives on the surface chemistry of particles. The inter-relationship between the surface chemistry of particles and the role of additives in controlling suspension rheology is now well understood for systems in which the average particle shape in the mixture is spherical or close to spherical. Luckily, this is the case for a large number of systems in the mining industry and the true role of typical additives in these systems will be explored. Difficulties arise for suspensions containing clays or other platey or needle shaped minerals and in many cases, quite small quantities of platey minerals dominate the rheology of suspensions. The role of additives in controlling the rheology of asymmetric particle systems is more complex but the effect of the additive in changing particle alignment in solution is the key to understanding suspension behaviour. The manipulation of the rheology of asymmetric particle systems will also be explored.

Jan 1, 1998

By McMahon DW, Schapper MA

Hard rock underground mining has been wedded to the drill-blast method of breaking rock. Current practice and technology have focused on greater efficiencies in the blasting and handling of ore, on the basis that thelower costs that come with larger scale operations compensate for the waste dilution associated with the bulk methods. However, it is suggested that new technology is available or is on the horizon that could completely change the shape of hard rock mining in the 21st century. Hard-rock continuous-mining machines, possibly assisted by high pressure water jets, coupled with automated sorting and materials handling systems, could re-orient the miner's focus to winning metal rather than mining tonnes of ore. More continuous mining processes could accelerate the penetration by high technology in the hard rock underground mine, with the potential of greater manpower productivities and lower costs per tonne of metal produced. This new technology will be important in maintaining a competitive supply of metals, given the falling headgrades of the orebodies remaining for development and the increasing market threat from manufactured substitutes.

Jan 1, 1985

By M Noy, P Hawkes

Improvements in the drill and blast process can impact on loader performance in a number of ways. The main effects being improved loading cycle times, less non-productive cycles such as oversize removal, clean-up and face raking and better bucket fill factors. The impact of improved loading cycle times on the overall cost and productivity of the load and haul cycle is very much dependent on the loader truck match and the management of the haul fleet. Previous work has shown that a 20 per cent improvement in dig cycle times may only lead to three per cent or less improvement in the overall productivity of the load and haul process. However, improving the mass loaded per pass by five per cent will lead to a five per cent improvement in productivity for any given haul fleet situation, assuming sufficient truck capacity. Work by Orica Explosives at Lab ChrysotileÆs Thetford Mine, Quebec, Canada showed a relationship between muckpile fragmentation and truck payload. With this in mind, work was carried out to determine the effect differing muckpile fragmentation distributions can have on excavator bucket fill factors. This work was performed in the laboratory to a 1:100 scale. Nine different distributions were used. These were characterised by the Rosin Rammler parameters, xc the characteristic size, and n, the uniformity index. The values of xc and n used were modelled on those previously measured at a Sydney quarry. For the range of distributions measured, it was found that the fill factors were lowest at a low characteristic size and a high uniformity index and highest at a high characteristic size and a low uniformity index. In other words the best fill factors were achieved with a more dispersed muckpile distribution with a larger characteristic size. The difference in fill factors was 16 per cent indicating that controlling the drill and blast process to produce a specific muckpile distribution can have a significant impact on the overall cost-efficiency and productivity of the load and haul process. Field measurement by Orica Explosives at a quarry in Canada supports this conclusion showing improvements of up to seven per cent in average bucket load by either increasing the characteristic size or decreasing the uniformity index of the muckpile.

Jan 1, 1999

By Gilligan P

The Selwyn gold-copper operation is wholly owned and operated by the Arimco mining group. The mine is located 150 kilometres south-east of Mount Isa. The primary extraction method for the gold-copper 251 orebody is by sub level open stoping. Secondary extraction is from the mass blasting of the remaining crown and rib pillars. The final mass blast of the 251 orebody occurred in December 1993. This paper details the design and execution of that firing.

Jan 1, 1994

By G Capes

A novel open stope design approach is presented that delivered improved performance in a mining area with poor ground conditions at the Olympic Dam mine. During 2019, a large open stope had an unplanned caving event resulting in the inability to extract the planned tonnes and subsequent sterilisation of nearby stopes. A design limitation was the lack of data and understanding around the alteration domain extents, the rock mass strength controls and limits, the failure modes controlling stope stability in the local area, and the use of conventional stope shapes. From the available data and failure observations, it was inferred that the dominant caving failure mode resulted from a blocky rock mass impacted by structure and alteration causing an unravelling failure mechanism. Numerical and empirical analyses were conducted to test this hypothesis and establish strength limits for design. The strength limits for the design were then used to provide a range of outcomes from which future stope design shapes such as chamfered backs could be selected. Three alternate chamfered geometries were selected to trial the innovative designs. The application of this methodology in 2020 resulted in overbreak reduction from >100 per cent in the initial caved stope to

Mar 29, 2023

The Kiirunavaara apatite-magnetite orebody is about 4 km long and approximately 100 m thick sheet-like body, which lies roughly in a north-south direction and dips from the horizontal plane along its entire length, in towards the town of Kiruna. The origin of this orebody has been a matter of controversy, with both magmatic and hydrothermal origins proposed. Traditionally and for practical purposes this rich apatite-magnetite ore has been divided into two main types: low phosphorous ore (B-ore) and high phosphorous ore (D-ore). Further the low phosphorous ore is divided into the low alkali (B1) and the high alkali (B2) ore.

Jan 1, 2006

The green field discovery of a two million ounce high-grade refractory gold ore deposit in the Indonesian Province of Sulawesi Utara, led Newmont to utilise its proven technical expertise in dry grinding and whole ore roasting to develop a 2000 tonne per day, 160 000 ounce per year operation in this remote and picturesque location.Located at an elevation of 250 in above sea level and ten kilometres to a deep water natural harbour, the hard rock open pit mine, process plant and infrastructure facilities were built to budget at a capital cost of US$132 million. The plant was commissioned with oxide ore, with the first gold poured in March 1996 and with refractory ore in January 1997. The operation rapidly met its production targets because of extensive forward planning and training programs developed for the local workforce. The presence of steep topography, fertile coastal plains, high rainfall, high seismicity of this location led to the decision to dispose of neutralised tailings in deep water off the coast instead of impounding tailings in a dam. This paper describes the development of the project and the challenges in developing a gold operation in a remote location which lacked infrastructure, the steps taken to ensure a smooth commissioning, and the selection of the workforce to operate a technically sophisticated facility.

Jan 1, 1997

By B Roache, J O’Brien, M Gray

Admixture use in cement products is commonplace in the construction and mining industries. Many Australian mines have an operational concrete batch plant and stock hydration control and water reducing admixtures. The benefits of admixture use, especially in shotcrete is understood and well documented. Cemented rock fill (CRF) is used to fill stope voids and create stable vertical and undercut surfaces at some Australian mines. These mines generally mix rock fill with a slurry of cement and water without the use of admixtures. Recently published work on optimisation of CRF mixes has mainly focused on the strength increases associated with changes to the mix grading proportions by the addition of fines, but not focusing on the potential benefits of admixture use. Admixture use in CRF may be the simplest CRF optimisation method, as the admixtures will often be added by the push of a button at the batch plant. A CRF testing program was undertaken to test the benefits of admixture use in terms of strength gain, using hydration control additives (HCA) and high range water reducer (HRWR) admixtures. Rock fill gradings were strictly controlled in the test process to allow clear definition of the difference admixtures provide in compression at 28 days. The testing results define admixture associated strength gains in a 6 per cent general purpose (GP) cement by dry weight CRF mix (131 kg of cement/m3). Costings have been developed to allow a mine operator to understand the cost benefits of admixture use in CRF due to reduced operating costs. Operational efficiency advances and a suggested admixture implementation plan for CRF optimisation is offered.

Nov 29, 2022

By J Visser

Dust mitigation has long been seen as nothing more than managing a nuisance issue, but the reality is that poor dust management can lead to one or more of the following negative consequences: an increased risk of safety incidents, lost revenue, reduced and possibly even lost licence to operate, regulatory intervention, high staff turnover and/or absenteeism and occupational health and safety (OH&S) issues. Dust mitigation and management is not a black art; rather it is a scientifically driven process that can provide an opportunity to increase profits, increase the companyÆs status as an excellent corporate citizen, enhance staff retention and reduce the safety risk profile of the operation.The way to achieve success in dust mitigation and control is to apply the scientific method to each problem that can arise and plague any operation by using current industry best practice. This method of dust problem-solving can be applied to dust issues arising from specific dust sources and locations. The dust sources can include wind impacting on stockpiles, open areas, tailings storage facilities, moving train and truck loads, vehicular traffic on roads, the operation of shovels, front end loaders, draglines and other equipment, as well as ore movement on conveyors.The solutions will come from a combination of deployment of dust collection equipment, dust and moisture monitoring equipment, the appropriate application of water and chemicals, the introduction and maintenance of appropriate barriers and the use of predictive data from local and public weather stations. The paradigm shift required is to view dust mitigation as one aspect of normal operational practice, not a ænice to haveÆ or æunnecessary expenseÆ as most operators currently view it. This attitude is becoming more important as more and more local communities oppose the development of mines. One of the reasons for this local opposition is the inevitable dusty environment that is usually associated with mining.Dust mitigation is not a significant expense if correctly designed and included into the system, either as part of the original design of the operation or as a brownfield installation after the fact. Indeed, there is always a loss of revenue associated with dustiness resulting from ore movement and avoiding this goes a long way to paying for any associated dust mitigating costs.CITATION:Visser, J, 2013. Dust mitigation - changing the paradigm, in Proceedings Iron Ore 2013 , pp 27-38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By C F. Stokes

The Trident Gold Deposit has been successfully developed by Alacer Gold (formerly Avoca Resources Limited) into a 1.3 Mt/a operation in the space of four years from discovery to first gold pour (2008). The current in situ Resource for Trident is estimated to be 5 900 000 t @ 5.0 g/t for 940 000 ounces at a cut-off of 1 g/t or 2 g/t depending on ore style. Production to date (Alacer and previous owners) is in excess of 500 000 ounces. The deposit lies towards the southern end of the Norseman-Wiluna Greenstone Belt in the Archaean Yilgarn Craton, where it is centred on the historical Higginsville Mining Centre, midway between the world class gold centres of St Ives (+15 Moz) and Norseman (+6.5 Moz). Trident is hosted primarily within a thick, weakly differentiated gabbro with subordinate mafic and ultramafic lithologies and comprises a series of north-northeast trending, shallowly north plunging ore zones. The deposit comprises two main mineralisation styles; large wallrock-hosted ore-zones comprising sigmoidal quartz tensional vein arrays and associated metasomatic wall rock alteration (Eastern Zone, Western Zone and Apollo) hosted exclusively within the gabbro; and thin, lode-style, nuggety laminated quartz veins (Athena and Artemis) that formed primarily at sheared lithological contacts between the various mafic and ultramafic lithologies. The initial interpretation of the Trident Deposit was based on steeply-dipping structures controlling the zones of mineralisation, with much of the targeting and drill-testing aimed at this style of orebody. Subsequent exposure of the orebodies has identified a series of shallow-east dipping mineralised systems (interpreted to be large reverse shears) that at their intersection with the steep-dipping structures cause significant gold enrichment. It is postulated that both orientations are primary fluid pathways with the intersection between the two resulting in zones with significantly high concentrations of gold mineralisation (in excess of 300 000 ounces). This new understanding on ore controls at Trident has identified that the thin lode-style shear-hosted laminated veins are continuous for over 1700 m along strike as they step en echelon down-plunge. In addition, a repetition and periodicity to the intersection between these steep dipping lode-style systems and the shallow-dipping mineralised zones (estimated to be 700 - 900 m down-plunge) has been identified which has considerably increased the down-plunge potential of the Trident Deposit.

Aug 22, 2011