Search Documents

In the first half of 1987 two four metre diameter raise bore holes were drilled at the Olympic Dam Project for ventilation purposes. The first hole, 476 m x 4.0 m diameter was completed in 96 days, 35 days longer than scheduled. The second hole, 407 m x 4.0 m diameter was completed in 39 days, 2 days ahead of schedule. Both holes were drilled with a Robbins 121R rig using a Wirth head that consisted of 23 face cutters and 5 side cutters, supplied by a contractor. After the sites were located a grouting program was carried out to help seal off an aquifer between 160 and 180 m below the surface. Cavities discovered in the Andamooka Limestone were filled with concrete. Because of the overlying dune sands and clay both sites were pre-sunk to the competent Andamooka Limestone.

Jan 1, 1988

By A R. Gerson

Pyrite, chalcopyrite and mixed sulfide samples, with and without quartz (5 wt per cent S), were subjected to column leaching to mimic natural weathering (cyclic wetting and drying). The pH and SO4 2- concentration of the column effluent was measured over a period of 78 weeks. The pH of the pyrite-only containing column rapidly decreased and remained under pH 4 after 12 weeks of leaching. The pH calculated assuming a 2:1 ratio of H + generation and SO4 2- release was slightly lower than that measured. However, a reduced H + to SO4 2- ratio of 1:1 is predicted if the release of aqueous Fe 2+ is assumed rather than the formation of Fe(OH)3. The pH of all columns containing only chalcopyrite or a 1:1 mole ratio of chalcopyrite and pyrite remained at or above pH 5 for the duration of the leach even though significant SO4 2- was released. One column containing the same initial surface area of pyrite and chalcopyrite but only approximately 0.10 the mole fraction of S as chalcopyrite maintained a pH of greater than five for the first 56 weeks of leaching and showed sporadic acid production thereafter. It is well established that oxidation of chalcopyrite results in a surface layer of polysulfide material. It is the formation of polysulfide that neutralises the acid produced on S oxidation through to SO4 2-. Hence where polysulfide formation occurs extensively on chalcopyrite the resulting solution pH decrease will be less than that based on SO4 2- production. The oxidation rate of sulfide minerals increases with decreasing pH and hence acid formation via sulfide oxidation to SO4 2- causes the subsequent oxidation rate to increase. The addition of calcite (CaCO3)to a pyrite column not only neutralises the acid formed but also decreases the rate of release of sulfate to solution by a factor of approximately 30. This is also the case where chalcopyrite is present mixed with pyrite. The rate of release of sulfate from the mixed sulfide mineral columns (after the initial release of the sulfate already present) was between one-fifth and one-tenth that in the absence of chalcopyrite.

Jan 1, 2003

Productivity of mines can be improved by taking fewer, but larger blasts. The initial blasts taken in starting a mining block are restricted by the low amount of void or space to fire into. Block cave mines are using a blasting technique to blast areas that have less than the normally accepted minimum void to establish drawbells for their orebody development. This technique used in block caving mines can be used to improve productivity in mining operations that utilise other mining methods. Some larger blasts have been done in mines, using open stoping methods, which have had void ratios as low as 13 per cent. This has been possible with the use of the explosive gases to transport the broken rock out of the area normally considered to be available to blasts. This trapping of the explosive gases in the broken rock has allowed rock to be moved over 30 m, horizontally, to allow for more void to be available in the blast area. This gives the necessary void ratio allowable to fire larger blasts. This paper will discuss the blasts where this technique has been used in mines to increase the tonnes fired in low void situations. It will also discuss where this type of blasting may improve the productivity of underground mines. Figure 1 shows the how explosive gases have enabled the broken rock to flow out of a draw point without the typical air blast and fly rock that would normally cause a rope suspended sign to be damaged beyond use.

Jan 1, 2008

Managers are demanding efficient use of their resources and part of this demand is leading to the idea of integrated audits for Occupational Health and Safety (OH&S), quality and the environment. It is possible to construct audits which test the compliance in this area with standards established by management systems and it may be that such an integrated audit of a site could reduce the time of auditing and be equally effective as three separate audits. However, this is only a maybe. To do an audit on all three aspects when they are not fully integrated results in more time wastage than doing three separate audits. But organisations are not structured around the audit process (some financial managers may query this statement). The organisational management systems are put in place to achieve the organisational goals - presumably in an efficient and cost-effective manner.

Jan 1, 1995

By Askew J. E

All facets of current practices of cable dowelling at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited are re- viewed. This includes materials specific- ations, installation practices and design pro- cedures. Cable dowelling for cut and fill stoping, square set timber stoping, longhole open stoping and level reinforcement is considered. Installation is simple and can be mechanised to eliminate heavy lifting. Quality control is essential for optimum performance of the re- inforcement. Design patterns must consider the mining method, reinforcement economics, acceptable stability standards and mine production priorities.

Jan 1, 1977

By Harraway D. H, Draper N

The association of graphite with a fine grained pyrite in the Mount Isa lead-zinc ore was investigated from mineralogical and metallurgical standpoints. The pyrite has been partially or completely replaced by galena and to a less extent by sphalerite, pyrrhotiteand chalcopyrite with the retention of graphite films or inclusions. During lead flotation the graphite imparts a spontaneous flotability to all associated minerals, resulting in a low grade fraction, which we call the carbonaceous fraction, floating with and diluting the lead concentrate. In times of low metal prices this fraction seriously reduces the economic value of the lead concentrate. A flotation procedure was developed to upgrade the carbonaceous fraction separately, producing an economic concentrate and a tailing.INTRODUCTIONThe lead concentrate produced from Mount Isa ores can vary from 20 to 50 per cent lead, depending on the locality in the mine from which the ore is obtained. Variations of this order are independent of ore grade and lead recovery. The large variation is related to the presence in the ore of a variable fast floating low grade fraction known locally as the carbonaceous fraction because of its association with graphite. During conventional lead flotation with sodium ethyl xanthate the carbonaceous fraction floats rapidly and unselectively with normal Mount Isa galena.The paper discusses mainly the examination and treatment of an average carbonaceous fraction, defined here as the fast floating material in the mill feed of late 1956. The ore was drawn from the Mount Isa Black Star orebodies. The fraction represented about 5 per cent of the total ore...

Jan 1, 1961

Answers to the questions "which rocks contain diamonds?" and "which indicator minerals should diamond explorers look for?" are no longer so easily obtained, now that diamonds are known to occur in lamproites and various types of lamprophyres, as well as their traditional source of kimberlites. One way of isolating those factors (host-rock"geochemistry, geographical or tectonic location, xenolith minerals, etc.) which are most critical in determining the diamond potential of a given pipe, is a detailed and critical re-examination of the huge volumes of accumulated data on kimberlites, lamproites and related rocks. A large analytical database to this end has been set up on an Apple Macintosh II microcomputer using the quasi-relational database management system 4th Dimension. Currently, it contains data for up to 90 major and trace elements, isotopic ratios and contained mineral compositions for some 4,000 rock specimens from all over the world. Many experiences in setting up this database are probably relevant to other geologists setting up their own systems: they include determining the relationships between data items; the advantages of codes over free text in representing categorical variables such as rock types; the need for rigorous error trapping and data validation; and the problem of missing data values and ambiguities thereof. The working system is now being used in a rigorous statistical assessment of the criteria which distinguish diamondiferous from non-diamondiferous rocks.

Jan 1, 1989

By Mills KW

Coal mine pillar design formulae available to mine planners are typically based on relationships determined for specific site conditions. Application of these methods is difficult when other factors, relating to mining or geological conditions, not specifically addressed in these relationships are encountered. A review of pillar design methods, coal strength properties and relevant field monitoring of pillar behaviour has shown pillar strength and deformational characteristics are extremely sensitive to in situ behaviour of the rock and other material components that make up the coal pillar system. A method has been developed that has been found to provide excellent correlation between existing field data using the strength and deformational characteristics of materials determined in selected laboratory tests. This method is based on definition of the loading conditions, accurate modelling of the strength, confining conditions and deformation occuring in the roof, floor and coal seam and definition of the in situ strength of coal based on underground monitoring of appropriately sized coal pillar. The design method is considered to provide an accurate and rigorous pillar design method that will give mine planners a more rational mine design capability which is based on the mine geometry and geological setting of the operation. It is envisaged that availability of such a method will allow significant optimisation of pillar layouts and more closely define the geological and mining issues that relate to pillar design optimisation.

Jan 1, 1992

This is the second of a series of papers dealing with Geology in Exploration. The first, published by the Australasian Institute of Mining and Metallurgy, Proceedings Nos. 143-144, 1946, was written as an introduction to the subject and employed the exploration geology of the Cobar field to illustrate the prospect thinking. This paper will be concerned with the problem of ore repetition in depth and borrow its- example from the Mount Lyell copper field. The writing will be taken up altogether by the example. Nevertheless the intention remains to develop the subject in terms of its wide interest and application.The Mount Lyell field possesses large actual and prospective resources within, and in the vicinity of, the known deposits. This paper does not bear at all on these accessible ore reserves and tangible prospects. There is also in this area evidence of deep ore. The possibility is of little practical interest at present. But the picture of ore repetition, exemplified by the Mount Lyell field, does matter now to the outlook on exploration in this country. For once this essential feature of ore occurrence is widely understood there may develop, on the scale warranted, the search for major deposits which do not outcrop but which are still at shallow depths because of the part erosion plays in this story of concealment and exposure of ore. Also there is the chance in some fields (including Mount Lyell) of a second harvest of orebodies within mineable depths. This exploration goal, introduced in the first paper, will appear more clearly as the Geology in Exploration series is written up. Here the concern is to show the character of the geological evidence which points to the occurrence and recurrence of ore in the earth's crust, the picture at the foundation of this exploration scheme. There is considerable information in the Mount Lyell area of the structures...

Jan 1, 1947

By L Lagoeiro

The samples studied in this paper were derived from the iron oxide facies of iron formations (IFs) of the Quadrilßtero Ferrffero, south-eastern Brazil. The rich-iron oxide varieties of the IFs can be regarded as Fe-O systems because they consist predominantly of aggregates of haematite and magnetite crystals. The study was based on carefully selected samples in which magnetite crystals occur as isolated large crystals set in a matrix of haematite grains. Optical microscopy and an electron microscope equipped with an electron backscattered diffraction (EBSD) system were used to investigate the microstructural and crystallographic relationships involved in the phase transformation between magnetite and haematite. The magnetite crystals in the IF samples are partially transformed to haematite and this process is also known as martitisation. This transformation occurs along the crystallographic planes {111} of the magnetite producing a characteristic triangular pattern of interlocking lamellae of transformed haematite crystals that are oriented parallel to octahedral plane {111}. This new generation of haematite is referred to martite because of the martitisation process. EBSD analyses show that the magnetite and the new haematite crystals, martite, share crystallographic planes of highest atomic density, eg {111} and (0001), respectively, possibly due to the ccp and hcp atomic arrangement of the two crystals. Stereographic projections of these two planes therefore coincide when the maxima of their poles are plotted. However, the crystallographic orientation of the haematite crystals in the matrix shows maxima of (0001) poles that do not coincide with those of {111} planes of magnetite. Consequently, it is concluded that the direct transformation to haematite crystals retains the crystallographic orientation memory of the former magnetite crystals, possibly due to the similar manner whereby their atoms are packed together in the crystal structures. On the other hand, no such relationships are observed between magnetite and haematite crystal in matrix. This suggests that haematite grains in the matrix may have been formed by other processes rather than those involved in the iron oxide transformation observed within the magnetite grains.

Jan 1, 2008

The Kennedy Siltstone Open Cut provides graded rock for stope filling. Rotary drilling of 310 mm blastholes with a Gardner Denver GD120 is used, and the successful application of an equilateral triangular drilling pattern is described. Charging practices and the development of bulk slurry handling are outlined. Blast monitoring plays an important role in K.S.O.C. drilling and blasting operations. The proximity of nearby residential areas (1300 m) and the Mount Isa Airport (4500 m) necessitates special attention with regard to the minimisation of both air blast and ground vibration levels. The application and control of drilling and blasting parameters has had a direct bear- ing on success of the mining operations and also played an important role in reducing the disturbance to the community.

Jan 1, 1978

Trial ore production began at the Hilton Mine in 1987 with ore being trucked into Mount Isa for treatment at the Lead/zinc Concentrator. The expansion of output from the Hilton mine required additional concentrator capacity which led to the design and construction of the Hilton Concentrator. Systematic laboratory and Pilot Plant testwork dating back to 1968 to develop a flowsheet and reagent regime suited to the varied and generally complex mineralogy of the Hilton ore was successfully concluded with a Pilot Plant trial using a sulphoxy based sphalerite depression system in early 1988.In May 1988, a decision was made to build a 750 000 t/y concentrator with some novel technological and capital-efficient features. The Hilton Concentrator commenced operations in December 1989 reaching target grinding rates and metallurgical performance by mid-1990. Current ore treatment rate is 800 000 t/y.Lead concentrates assaying 43 - 48 per cent Pb are combined with the Lead/Zinc Concentrator lead concentrates and smelted at Mount Isa. Zinc and Low Grade Middlings (LGM) concentrates are filtered in the zinc filter plant at Isa with those from the Lead/Zinc Concentrator and then railed to Townsville for export or treatment in Australia.

Jan 1, 1993

Fleet management systems have been adopted by many open pit mines throughout the world and the resulting improvement in truck cycle times has been one of the most significant contributors to mine efficiency. Ongoing enhancements to fleet management systems such as interfaces for vital signs monitoring have given incremental efficiency gains. Each incremental improvement is another step towards a grand vision of a totally automated mine. A relatively new fleet management system is being integrated with two other technologies to provide a highly reliable platform for a networked information system which monitors mine machinery and production. The paper reviews the integration project, the features of the new mine site information network platform and the contribution to productivity and safety. The new fleet management system has a predictive truck dispatch algorithm. It also has a distributed database that replicates rapidly so that each machine in the fleet has an identical database, thereby making each machine aware of other machinesÆ locations on the site. High precision systems for navigating and monitoring machinery such as drills, dozers, draglines and shovels provide individual machine operators with cockpit style real-time information to increase their operational efficiency. The integration of the new fleet management systems capabilities with the high precision systems that provide production information, machine vital signs data and operator information means that the mine operations and maintenance managers have real-time access to the whole mine siteÆs production data. Such a mine monitoring and reporting system is dependent on reliable wireless communications and reliable positions. Positions in fleet management and high precision systems for open pit mines are usually provided by global positioning system (GPS). Other global navigation satellite systems (GNSS) such as Glonass, and in the future Galileo, will provide additional satellite cover; however, some parts of open pit mines do not have enough sky visibility for reliable GNSS positioning and so a new centimetre level wireless positioning system called Locata is being integrated with the fleet and high precision systems to augment and backup the GNSS positions. The final integrated system will provide the highest levels of reliable position-based information to all stakeholders in a mineÆs operation, ensuring gains in productivity and safety.

Jan 1, 2008

By A Xenidis, N Papassiopi, I Paspaliari

Acid generating sulfidic tailings covering a surface area of approximately ten hectares have been deposited in the historic mining area of Lavrion in Greece. For the development of a remediation strategy, the performance of three alternative acid generation control techniques was assessed under actual field conditions. The techniques involved the application of dry covers, including a synthetic HDPE liner and a compacted clay layer with capillary barriers. Furthermore, the potential formation of a low permeability hardpan layer at the sulfidic tailings surface by limestone addition was investigated. The field tests covered an area of 2500 m2, which was divided in equal quadrants, corresponding to the control plot and the three alternative remedial options. To monitor the amount and quality of percolated water, lysimeters were installed beneath the four plot areas. Based on the monitoring results over a period of six years, due to the dry climate encountered in the Lavrion area, a low amount of water percolates through the pyrites if no action is taken (control area), corresponding to 20 - 25 mm per year. This water is highly acidic, pH = 1.2, and contains a heavy load of contaminants, eg Fe 40 g/L, Zn 15 g/L, and As 1.5 g/L. The HDPE cover eliminated the percolation of water into the material for a period of five years, whereas thereafter the volume of leachates increased to values similar to those recorded in the control plot. The water collected in the lysimeter of the clay cover has been minimal corresponding to approximately five per cent of the drainage volume produced in the control area. In the fourth plot, which involved limestone addition to sulfidic tailings, the volume of drainage initially collected was almost double compared to the control area. After three years of monitoring, significant reduction in the amount of percolated water was observed, attributed to the formation of a cemented layer (hardpan), at a depth of 40-80 cm from the testpad surface.

Jan 1, 2003

By Stanton G

The Department of Mapping and Surveying (DMS), the Australian Key Centre in Land Information Studies (AKCLIS), the Department of Industry Development (DID) and the State Government Computer Centre (SGCC) are testing a regional information network in northern Queensland. Several study sites have been chosen by different groups of participants. The members of each common-interest group share their data for the site. They can also access datasets supplied by other organisations that are not directly involved in the particular study being undertaken. The participants include state government departments, local authorities, fed- eral organisations and the private sector. The participants communicate with computer systems in Brisbane via Q-Net. Q-Net is a pilot State government tele- communications network, established by the Department of Industry Development. Q-Net uses the communications sat- ellite AUSSAT 1 as the primary instrument of data transfer. The Q-Net network is a star system, with a Master Earth Station in Brisbane acting as a hub for radial earth stations, located throughout Queensland.

Jan 1, 1987

By W A. van der Westhuizen

Selective mining played a major role in saving a mine and a communityÆs existence as well as creating a working culture that is the model for all KumbaÆs mines. The successes that resulted from selective mining led to receiving KumbaÆs highest award (it was the Gold Medal Breakthrough project of 2003) as well as the productivity award at the National Productivity Institute award ceremony in 2004. Kumba was established in November 2001 (previously Iscor Mining). The new company identified Mineral Resource Management (MRM) as one of its key drivers and an initiative was launched to define MRM in the Kumba way. Best MRM practices at the Kumba mines were included in the definition. Selective mining was born out of this initiative. One of the key principles of good MRM practice was identified as: æThere must be a balance in the operational processÆ. This principle was applied with great success at Thabazimbi Iron Ore mine in the Limpopo province, South Africa. The emphasis of this paper will be to show how value can be unlocked throughout the whole mining value chain. In the past (up to 2001) the mine went through a number of crisis situations: planned production performances were not reached, the stripping ratio was extremely high with two new pits, the product beds were not of constant quality, slope failures were big risks, flooding could and did cut off half of the ore supply, and restructuring demoralised staff.This paper focuses on: selective mining throughput drivers, and selective mining and its role in achieving this balance.The results were dramatic, with huge improvements in production results, stockpiles, plant yields and product bed specifications. The mine was brought into balance and a self feeding loop was created with positive spin-offs up to this day.

Jan 1, 2005

By Z Chang, S A. Mrozek, S Windle

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. It is important to understand skarn-porphyry transitions in order to use exposed skarns to look for associated and potentially larger porphyries. For such purposes, a good start is to understand the transition between porphyry and skarn in known deposits. In this contribution, we report the transition at Antamina, Peru, where skarns occur in and around a Miocene complex comprised of more than seven porphyritic intrusions. There are three types of skarn-porphyry relationships. The earliest intrusive phase, P1A, contains both endoskarn and porphyry-style quartz veins with secondary biotite halos. The porphyry quartz veins and endoskarns formed at the same time. Locally, the intrusion contains only endoskarn without porphyry quartz veins and is surrounded by exoskarns in carbonate wall rocks. In the third scenario, later porphyry (P2) intruding into P1A porphyry and skarns related to P1A contains abundant granular quartz veins and secondary biotite alteration but does not have significant endoskarn. The granular quartz veins also extend into earlier P1A skarns. The scarcity of endoskarn associated with P2 is related to the supply of Ca. The earliest P1A intrusion intruded into carbonates that supplied abundant Ca, therefore both endoskarns and exoskarns formed. In contrast, where the wall rocks of the later P2 intrusion are P1A or skarn related to P1A, there was little free Ca, therefore only porphyry-style quartz veins formed.CITATION:Chang, Z, Mrozek, S A, Meinert, L D and Windle, S, 2015. Skarn-porphyry transition – an example from the Antamina skarn, Peru, in Proceedings PACRIM 2015 Congress, pp 409–414 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Kissell F. N, Thimons E. D

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined- out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a longwall operation that uses ventilation to carry off hazardous gases, and two are room- and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases, employment of the Bureau's SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1988

Nippon Telegraph and Telephone Corporation (NTT) developed a new construction method (the M-2 method) that could drive a long, curved small-diameter tunnel (4>1.2 m) without human labor. This method employs the cast-in-place lining system, using quick-hardening resin mortar, so that it can greatly increase the driving distance and execute both long distance driving (longer than 500 m) and curved driving with a radius of curvature of 200 m. Furthermore, the central control system with a mini-computer in a vertical shaft enables all work in a small-diameter tunnel, i.e., excavation, lining, and transportation of excavated soil and materials, without human labor. NTT conducted several field tests and a Practical Application Test (P.A.T.) under a public road bearing great traffic. Good results were obtained and the practicability of this method was demonstrated. Therefore, from now on, NTT will apply this ii-2 method to drive telecommunication cable tunnels in urban areas. This method will also be applicable to constructing public tunnel facilities, such as for water, sewage, electricity and gas.

Jan 1, 1987

By C J. Ptacek, J G. Bain, D W. Blowes

The passive interception and in situ treatment of groundwater using permeable reactive barriers (PRBs) has, within the past decade, become an accepted remedial approach to the control of plumes containing dissolved organic and inorganic contaminants. Since the first applications of the technology in the early-1990s, there have been several field-scale PRBs that have provided excellent treatment of dissolved metals in groundwater. Additional commercial applications and demonstration projects continue to be developed. Three field-scale applications and supporting laboratory columns have shown that several thousands of milligrams per litre of sulfate, more than 1000 mg/L iron, and several tens of milligrams per litre of other metals can be removed from groundwater by PRBs that promote sulfate reduction. The reactive materials, which incorporate various forms of organic carbon, promote microbially mediated sulfate reduction, the generation of hydrogen sulfide, and the subsequent precipitation of sparingly soluble iron and other metal sulfide minerals. Effective performance has been achieved by PRBs installed at a mine-tailings impoundment in 1995 (Sudbury, Ontario) and at an industrial facility (Vancouver, British Columbia). These PRBs have removed iron and other metals from groundwater. Similar materials were also used to create reactive layers within test cells directly in a tailings impoundment in 1999 (Timmins, Ontario) with the objective of removing iron and sulfate from the pore water before it migrates from the tailings impoundment. Zero-valent iron (ZVI) has been shown to provide excellent removal of chromium (VI) in a PRB, which was installed at the US Coast Guard facility in Elizabeth City in 1996, by reduction and precipitation reactions. Laboratory tests have also shown that ZVI reduces As(V) to As(III), which is subsequently removed from solution by co-precipitation with iron oxyhydroxides. In groundwater containing sulfate, ZVI and mixtures containing organic carbon can promote sulfate reduction and the subsequent precipitation of sparingly soluble arsenic and other metal sulfides. A trial PRB system was installed in 2001 and was shown to attenuate arsenic and other electroactive metals in groundwater at an industrial facility in northwestern Ontario. Basic oxygen furnace (BOF) slag, a waste material generated by the steel industry, has shown excellent potential for the removal of phosphate, elements such as arsenic and water-borne pathogens from groundwater in field and laboratory tests.

Jan 1, 2003