Search Documents

Severe development difficulties were experienced soon after in-seam mining commenced at Appin Colliery in'1962. Thirteen years later no significant pro- gress had been made in overcoming some aspects of this development problem. Some success had been achieved in destressing roadways both in development and pillar extraction. Longwall retreat mining had shown promise of being highly productive but at an extremely high cost in terms of development requirements both in number of roadways and intensity of support in those roadways. No real advance was made in the problem of driving the first heading of a group of headings under conditions of apparently high stress in directions other than the preferred mining directions, although failure of the roof in this heading did seem to give easier work in the subsequent headings driven particularly if they were driven on narrow centres.

Jan 1, 1976

By G Munro

he Melbourne City Link project will complete a missing link between two existing major freeways in the Melbourne road network, providing a much needed bypass of the Central Business District for through traffic. The project, which is being financed under a BOOT arrangement with the Victorian State Government, involves the upgrading of significant stretches of existing freeway and the construction of new sections involving viaducts and tunnels. The tunnel sections, which are the focus of this paper, are beneath residential and business areas, the Yarra River, the Royal Botanic Gardens and significant sporting facilities where surface construction would be either impossible or unacceptable (reference Figure 1). The shorter, 1.62 km west bound Domain tunnel comprises two cut and cover sections through Olympic Park then the Yarra River, the driven section of 0.68 km length and exits through a common cut and cover section with the east bound tunnel under St Kilda Road and Sturt Street. The longer 3.76 km east bound tunnel commences at the common portal, through cut and cover under St Kilda Road then 2.86 km of driven section before exiting at a cut and cover section at Burnley. The longer Burnley tunnel has an access and ventilation shaft at approximately its mid point.

Jan 1, 1999

Alluvial mining even of shallow deposits is often economically a marginal proposition and causes significant disruption of the land surface through the need for large scale excavation. In-situ leaching using chlorine-based solutions eliminates the need for excavation, the disruption of surface activities, and may greatly reduce processing costs and improve recovery especially of fine gold. A spreadsheet model has been developed to design and analyse the economics of in-situ leaching of alluvial deposits. In-situ leaching of shallow deposits may be achieved in a number of ways including solution infiltration via perimeter ditches or the use of injection and production wells. In most instances deeper alluvials may only be processed using well systems. Two deposits are analysed in this paper. The first consists of one metre of payable wash beneath one metre of overburden. Some thirty fields per year are treated processing 450 000 BCM per year at a cut-off grade of around $4/tonne ($8/rn3 or the gold value equivalent of 0.26 gh or 0.52 g/m3). The principal costs are well drilling and labour. Sensitivity analysis indicates that doubling the throughput halves the cost. The economics of the project are relatively insensitive to reagent costs and consumptions, and halving the recovery doubles the cut-off grade. Shallow deposits treated using the infiltration ditch system may be marginally cheaper and more conveniently managed although this depends on the relative cost of digging the perimeter ditches. In a second example, deep leads with one metre of wash beneath 30 metres of overburden necessitate significant drilling and feature reduced throughputs as a consequence. In the example chosen 30 fields a year are processed for an annual throughput of 65 000 tonnes costed at around $20/tonne (1.4 g/t Au equivalent, $40 /m3). Sensitivity analysis indicates that throughput, and drilling cost per metre are not important but there is a high sensitivity to recovery and to the depth to payable wash.

Jan 1, 1992

MERLIN, the Queensland Department of Minerals and Energy's corporate geographic information system, provides ready access to all georeferenced data held by the department. Its aim is to provide a consistent, current, statewide coverage of timely information to assist in tenures management, exploration targeting and competing land use decision-making. Initially developed in 1988 and under continual enhancement since then, its functionality is the result of on-going close consultation with a wide range of departmental clients and potential users. A true geographic information system, MERLIN maintains both graphical data with linked textual information on a wide range of features of interest. The proprietary software products Arclnfo and Oracle are used to hold the graphics and attribute information respectively. Access to information is provided by a specially designed graphical user interface programed in-house. Hardcopy output of graphics displays including related attribute data as well as detailed reports of textual information can be retrieved at any departmental office. MERLIN is a network of computer systems which link each of the Department's regional offices and head office in Brisbane. The current state of exploration and mining is maintained by departmental officers processing tenure applications, transactions and dealings directly into the system. Data entered at regional offices are transferred overnight to head office to up-date central records and maintain a currency of data statewide as at the close of business the previous day. Through MERLIN the Department of Minerals and Energy now offers a much streamlined tenures management service as well as access to information about past exploration and mining, Queensland's mineral and energy occurrences and resources, and up-to-date information on the state's geology including maps, boreholes, geophysical surveys and field observations. In the future, this Geographic Information system will be invaluable to the mining industry in the development of mining projects.

Jan 1, 1995

By Stitt P. H

This paper provides a brief historical review of the invention of the spiral separator and its adoption into Australian metallurgical practice. The purpose of the review is to demonstrate that spiral development to date appears to have been a largely empirical process, and that the cur- rent resurgence of interest in the spiral, especially in the coal industry, warrants an increased fundamental research effort. Current research work concentrating on empirical modelling is outlined, while some preliminary experimental results of a more fundamental nature are presented and some research of other disciplines interested in particle transport introduced in order to stimulate further work and discussion.

Jan 1, 1988

By Fazakerley VW

The Murrin Murrin deposit is located about 210 km NNE of Kalgoorlie and 50 km E of Leonora in the North Eastern Goldfields region of Western Australia at latitude 28¦ 50'S. longitude 121¦ 54'E on the Laverton (SH 51-2) 1:250 000 map sheet. The tenements are held by Anaconda Nickel NL. Geological investigations between 1994 and 1996 resulted in resource calculations being completed for the ten lateritic nickel cobalt deposits shown in Figure 1. At a 0.8 per cent nickel cut-off the resources at May 1996 for the nine deposits are 116.8 Mt at 1.10 per cent nickel and 0.082 per cent cobalt. The nickel-cobalt mineralisation is contained in a laterite profile developed over Archaean serpentinised peridotites. A bankable feasibility study has been completed and the project is scheduled to be in production by the beginning of 1998.

Jan 1, 1996

By Winrove G. S, Herdie G. J, McCarthy C. A

Production of hot metal from the Hlsmelt Research and Development Facility at Kwinana, Western Australia commenced in October 1993. The stand-alone facility is a unique, coal-based, integrated ironworks equipped to process iron ore fines to pig iron and simultaneously undertake a wide range of research tasks. The data generated will be used to verify the commercial potential of the technology and to set the design and operating parameters for a full-scale production plant. The design, construction, commissioning and initial operation of the HRDF has required many innovative and practical solutions to be developed and implemented by the international group of organisations contributing to the Hlsmelt Project. Initial operation has produced results which demonstrate the potential of the unique process technology associated with the core plant smelting unit. The recent achievement of post-combustion levels of 60 per cent with heat transfer efficiencies greater than 85 per cent demonstrates that the performance obtained with the Small Scale Pilot Plant in Maxhutte, Germany can be reproduced at a larger scale. The results presented in this paper support the thrust for further intensification and future commercialisation of the process.

Jan 1, 1995

The Quioma Mine is located along the axis of the Cordillera Oriental, 130 km southeast of Cochabamba, South Central Bolivia. Silver, lead, zinc, antimony, and gold have been intermittently produced from veins in the Quioma area since Colonial times. Mineralization occurs within steeply dipping fissure veins transecting moderately folded Lower Ordovician sediments. Tectonic activity is early to mid-Tertiary and the vein system parallels the fold axis of a major northwest-southeast striking, doubly plunging anticline. Vein sets occur within a 2 km wide band over a strike distance of 13 km along the northeast limb of the anticline. Economic mineralization occupies syntectonic pre-mineral fault zones developed in more competent stratigraphis units of Lower Ordovician clastic sediments. Veins average 55 cm in width, although mineralized structures up to 3 m wide with a known strike length of several hundred meters have been mined. Mineralization consists of siderite, argentifferous galena, sphalerite, and quartz, with minor amounts of chalcopyrite, barite, and bournonite. Pyrite is rare except at the Boston vein where it occurs with stibnite that contains trace amounts of gold. A marked characteristic of veins in the district is evidence of repeated stages of movement during mineralization. Intrusive rocks are rare in the Quioma area. Narrow porphyritic dikes of Andesitic composition averaging 1 m in thickness have been observed. These dikes occasionally show a close spatial relationship to the veins and are often kaolinized and carbonitized. Vein and dike contacts are sharp and alteration does not appear to extend into the wall rock. Mineral zoning is suggested by antimony mineralization observed in peripheral areas of the anticline.

Jan 1, 1987

Initial coal production at Ulan was solely from underground mines. A significant increase in demand for steaming coal in the late 1970's emphasised the need to further expand production and led to the development of the open cut mine which commenced commercial production in June, 1982.During the initial stages of mine planning, feasibility and cost studies were undertaken to determine the most suitable method for coal haulage from the pit. The comparison between a conventional truck haulage system and an in-pit crushing system using a mobile crusher and moveable belt conveyor haulage confirmed that the mobile crusher and conveyor system was superior in every respect for the Ulan mining operations.Technical features and design parameters for the major items of equipment are outlined as well as operating, manning and performance assessments. Minor equipment problems were encountered during initial operation but these have since beenrectified and the plant is now capable of exceeding the design production. Maintenance and energy costs are considerably lower than originally estimated and production efficiencies are continually improving as operators develop new techniques and procedures in the handling of the equipment.

Jan 1, 1985

By La Brooy S R, Fenton K

A low grade copper flotation tailing from Telfer containing 1.2% Cu as chalcocite and cuprite and 5 gt-t Au was leached with ammonia, cyanide and ammonia-cyanide mixtures to extract copper and/or gold. Direct cyanidation extracted both copper and gold but consumed about 30 kgt 1 NaCN. Pre-leaching the tailing with an aerated ammonia solution containing 28 kgt 1NH3 and 17 kgtl(NHa)2S0a at pH 10 readily extracted up to 95% Cu in about 6 hours under optimum conditions. However pH and total ammonia concentration were critical factors. Subsequent cyanidation ex- tracted 80% Au using 6 kgt NNaCN. Ammonia-cyanide mixtures werefound to selectively leach gold over copper depending on the concentration and relative proportion of NH3 and CN. The best composition for leaching up to 80% Au from Teller tailing was 1.6 kgt t NaCN and 1.1 kgf 1 NH3 in the presence of 0.3 kgt t Cue+. Such a mixture left only 50 mgL-1Cu in the final solution after precipitation of some of the initially dissolved copper.

Jan 1, 1991

By C McIntosh, M Carder, P M. J Durance

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Disseminated, gold-bearing sulfide minerals hosted in sheared, wall rock metasediments and clay alteration zones comprise one of the dominant styles of Palaeozoic orogenic gold mineralisation within the Reefton Goldfield, and is exemplified by OceanaGold’s Globe Mine. This study begins the exploration and characterisation of the gold-arsenic-antimony mineralisation hosted within the dominant lithologies of the Globe-Progress shear zone. The main gold-bearing sulfides are pyrite, arsenopyrite and stibnite. Pyrite and arsenopyrite are not compositionally uniform across the Globe-Progress shear zone. Pyrite from the mineralised greywacke and argillite has higher As contents than pyrite in the host rock and pug breccia. Furthermore, the mineralised greywacke and argillite pyrite are enriched in As from core to rim. The 3D models based on bulk assays reveal a significant correlation in the distribution of Au, As and Sb. The interpolant for Sb envelops those for Au and As, which in turn are very similar to each other in their vertical and lateral extents across the shear zone. This result is consistent with earlier findings that the occurrence of stibnite represents a separate and likely later phase of mineralisation relative to that represented by the formation of disseminated pyrite and arsenopyrite both of which exert a stronger control on the distribution of As.CITATION:Durance, P M J, Christie, A B, McIntosh, C and Carder, M, 2015. The composition of disseminated, gold-bearing sulfides within the three-dimensional framework of bulk Au, As and Sb in the Globe-Progress orogenic gold deposit, Reefton Goldfield, New Zealand, in Proceedings PACRIM 2015 Congress, pp 327–334 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Garg R. K

Himalayan ranges on the northern border of India are source of many perennial rivers and suitable sites for large dams have been located therein. However, Himalayas are young mountains and comprise of comparatively weaker rocks having adverse geological features like shear seams, thrust zones, minor and major faults and intense jointing. Tehri dam project under construction, is located in lower Himalayas. It envisages construction of a 260.5 m high earth and rock fill dam and an underground power station of 2000 MW (Eight machines of 250 MW each, four of which will be reversible) installed capacity. This dam will be the highest and the underground complex will be the largest to be constructed in India in the Himalayas. The under- ground complex comprises of 25 km of tunnels varying in diameter from 6 m to 11 m and seven large cavities of various sizes, the biggest being 22 m in width, 194 m in length and 65 m in height. Rock formation in the power house complex belong to phyllites having various joint sets spaced from 0.5 m to 3 m. Due to the poor geological conditions and closely spaced net work of large cavities, the planning, analysis and design of the cavities is a challenging job. Many aspects have to be considered in determining the sizes, locations and orientations of the various cavities taking into account the properties and jointing pattern of rock mass, functional requirements and economics. Correct evaluation of loads and forces is necessary for economical design of supporting system for the various cavities. Rock loads on the roof of cavities and their supporting system will be assessed with the help of the latest methods. The stability of the rock mass around the cavity will be evaluated by elasto- plastic method using finite or boundary element techniques. A scheme of field investigations, laboratory tests and instrumentation for deter- mining rock properties in preconstruction stage and for monitoring behaviour of the underground cavities during and after construction is envisaged.

Jan 1, 1987

Optimal drill and blast design is a process often neglected by many underground hard rock mines. This is even more important to the new mine where ring designs need to be implemented and refined in a short period of time. In today's environment where more and more mining is being carried out by contract specialists it is the co-operation between a principal and contractor, who are working towards a common goal, that achieves the highest quality end result. The development of drill and blast designs that cause minimal damage to the mine infrastructure is particularly important to Northparke's E26 Block Cave Mine, as it consists of a single extraction level which must survive intact for the life of the mine. The advanced undercut mining method implemented at Northparkes is fired in a sequence which protects the mine development from potentially damaging abutment stress. This paper details how blast designs will be optimised and sequenced to satisfy the conflicting objectives of maximum rock breakage inside the drill pattern and minimum rock damage outside the pattern.

Jan 1, 1995

By B Bendtsen, L McQueen

The use of shotcrete as an efficient means of both temporary and permanent ground support has continued to grow over the last 30 years, with its use underground now commonplace around the world. However, the development of analytical design methods has lagged advances in material and application technologies. Historically, part of the reason for this was a lack of understanding of how shotcrete linings actually worked. Considerable progress has been made in this area in recent years and this paper attempts to summarise the current state of practice with respect to shotcrete lining design. It then concludes by summarising areas where the authors consider future research and development is still required.

Jan 1, 2008

By S Pollak, A Amon

This paper describes the current and finished design work which has been performed for shallow rock station caverns for New York CityÆs first new subway construction in 60 years. A new robust, sophisticated, design procedure has been developed for two up to 30 m wide caverns, with overburden of less then 12 m, and rock cover to span ratios (C/S) in the order of 0.25. The design is based on empirical input parameters like the Q-value, rock mass rating (RMR) values, rock mass class after Cording (1984), cover to span ratios, which have been validated by the use of structural computer models as well as two- and three-dimensional numerical discontinuum models. The design approach is a staged approach using first principles, empirical models and non-linear FEM and DEM models. In addition, the paper describes the factors and circumstances why shallow caverns have been selected instead of cut-and-cover structures and why all the underground station structures have been developed as drained structures.

Jan 1, 2008

This paper is intended to continue the subject in the light of recent work, from where it was left at the conclusion of the discussion on the excellent paper by the late Mr. Noel Haszard. The position then obtaining is briefly summarised below:-The points which received general agreement at that time were:-'(1) That the gold occurs, probably in an elemental form, in a state of very fine division in the pyrite.(2) That the aim in roasting of Kalgoorlie flotation concentrates should be to obtain the maximum porosity possible. The gold tellurides were amenable to treatment with either a' solution of high lime and cyanide strength combined with fine grinding, or bybromocyanidation without re-grinding.(3) That a low roasting temperature is essential during the elimination of the first atom of sulphur, if the final calcine is to give a good extraction by cyanidation.(4) Even with the best temperature conditions of roasting then determined, and after a period of cyanidation of the calcines until no further extraction was obtainable, the lowest calcine residues obtainable were equivalent to approximately 1·8 dwts. per long ton, based on an original concentrate of pure pyrite.There was some division of opinion at the time as to whether the temperature of the later stages of roasting was significant, and also as to the reason why the initial roasting temperatures had so marked an effect.

Jan 1, 1939

By Buizen M, Eagleton A. C

The results of calibration trials conducted on parachute stoppings both overseas and in Australia under a recently completed NERD&DC grant, are presented. Applications of parachute stoppings, for rapid regulation and control of ventilation networks are described including use in blasting areas and rescue work. Several parachute-type stoppings are described and their applications Investigated

Jan 1, 1988

After extensive testing and a period of plant trials to establish the benefits of Caro's acid (H2S05) as an alternative oxidant, Queensland Mines Limited (QML) decided to replace pyrolusite with Caro's acid in its acid leach uranium treatment plant at Nabarlek. The decision was based on the reagent savings and environmental gains associated with the removal of manganese from the process liquors, as well as the labour savings and improved oxidation reduction potential control possible in leaching using the Caro's acid system. The permanent Caro's acid generating plant was designed by Interox Chemicals Pty Ltd of Australia (IC) to suit QML's require- ments and differed from the unit used during the plant trials. Commissioning of the plant was completed in April 1983 and it has been continuously used since that date.

Jan 1, 1984

**Add abstract here**

Jun 1, 2010

By Steinbrucker G

Improvements in mining by the application of electronics necessitates analy-sis of the objectives and problems. A detailed analysis has shown that increased tunel-ling performance is one of the most important objectives. In mining, the environmental conditions for machines, their handling and servicing are very hard. Therefore a health monitoring system for tunnelling machines in hazardous areas has been developed. This system measures operational parameters, such as-flow, pressure, temperature, etc., de-rives forecasts of possible failures from these values, and assists maintenance person-nel. Important data are transmitted to a surface computer via telephone cables. Health monitoring is based on the cognition that slow deterioration of characteristic parame-ters, e.g. fluid loss, are symptoms of wear. Sudden changes of machine parameters indi-cate sudden destruction. Computer technology is very advanced, but transducer technolo-gy has not,been able to keep pace. Filling the yawning gap in the mining industry is a challenge to technology and requires special techniques. Machine monitoring and automa-tion in underground mining is still in its infancy. A lqt of development and research work is still necessary. The risks are great-The expected benefit due to increased min-ing performance (up to 5 %) justifies the risks in development.

Jan 1, 1985