Search Documents

The intention of this paper is to examine the practical and technical aspects associated with the measurement of blasting related phenomena. The emphasis is directed towards the acquisition of quantitative data rather than its theoretical interpretation. The application of advanced technologies will require that many more people involved with blasting become familiar with this topic. Against the many other disciplines where measurement may be beneficial, blasting is peculiar on several counts. 1) It must almost always be carried out in the field, and very often in a production environment. 2) Much consideration must be given for the safety of personnel and equipment. 3) The process is dynamic and seldom repeatable. Because the blast process is so dynamic there is little opportunity for direct examination. For this reason measurements are almost universally made using electronic techniques. In this way the event can be captured faithfully as it occurs and later examined in detail, after the fact. It is obvious that some familiarity with these electronic techniques is a necessary ingredient for successful blast monitoring.

Jan 1, 1990

Daily geological mapping of the Panguna porphyry copper/gold system since mining began in 1971 has provided a good basis for resource estimation and mine planning as the mine and estimation methods have advanced. Geology defined during evaluation and early mining has been substantiated and many smaller features have been better defined or identified. Breccias, pebble dykes, major structures and location of lithology contacts important to short term planning and long term pit slope stability have been defined. Correlation of copper and gold with breccia zones is quite striking and was not fully appre- ciated at the end of evaluation. Pit mapping geology, and diamond drill geology and assays, are now routinely added to a Geological Data base on computer, which forms the major geological data base for modelling the deposit. Geology from diamond drill logging, updated by pit mapping, and assays from diamond drilling updated by blast hole assays have been incorporated in a 45 bench deep 486 000 block computer based block model which forms the basis for long and short term planning. The introduction of pre-concentration scre- ening, based on the distribution of mineralisat- ion and fracturing, puts more emphasis on the definition of grade distribution at low concent- ration and on structures in the rock. Geostatistics is now used for resource estimation and has produced acceptable estim- ates. but these need to be refined, particularly in peripheral, low grade areas of the deposit.

Jan 1, 1987

By L Soares, W T. Hennies, F Fujimur

Barra Bonita reservoir, located in the Sao Paulo State, Brazil, has been mainly used for local navigation and electricity generation to supply a prosper region in the country. Sand mining activities in that area have an important social and economic meaning for the local community. In this reservoir there are several sand mines that produce around 45 000 m3 of sand a month. These deposits were rich in material used as concrete aggregate in the civil construction. However, nowadays a significant increase in the demand of gravel can be observed, representing a serious productive problem. This material hasnÆt been well accepted by the market and, through the years, it was disposed at open sky in piles as waste deposits. This deposits have caused environmental problems like visual impact, reduction of free spaces outside and inside the mine, source of material to erosion and sedimentation processes in lower areas, flooding as a result of the filling up process in the drainage system, among others. For a lack of an appropriate technological characterisation, this material have been mainly used to pavement internal and external areas in the mine, with lower cost associated. With the purpose of evaluate the usefulness of this material in the conventional concrete, there were conducted several tests in the disposed residue including petrographical, physical, and chemical characterisation. The petrographical analysis and the preliminary results of the study showed that the material reacts with the alkalis that are present in the conventional cement (CP-II-E-32). In order to make the application technical and economically possible a research was developed seeking forms to correct this characteristic by adding special cements with high pozzolana content. The results of the technological, physical and chemical characterisation of the products indicated the technical viability of the use of that material. The study also allowed projecting environmental improvements resulting in the elimination of the waste piles.

Jan 1, 2003

By Durucan S

The southern Attiki peninsula is a very interesting area from an environmental point of view. The port and the city of Lavrio is situated at the east coast of the peninsula with about 10 000 inhabitants and there are also a few villages in the vicinity. The south-eastern part of the peninsula hosts the famous Lavrio mines which exploited the silver bearing orebodies of the area for more than 25 centuries. As a result, soils around the city of Lavrio are polluted with high heavy metal loads. The area is also of archaeological interest, as there are well preserved remnants of ancient mining and processing plants and archaeological sites. Soil samples collected from an area of approximately 120 km2 around Lavrio were analysed for their metal contents and the spatial distribution of the concentrations of ten selected elements were estimated from these data sets. The spatial data analysis and transformation capabilities of Geographic Information Systems, combined with extensive mining and geological data, helped the authors to identify the extent and causes of metal pollution around Lavrio.

Jan 1, 1995

By McLennan T, Howells E, Zastawny H, Watt J. S

Nuclear techniques have been used to determine the solids weight fraction (W) and ash content of (fine) coal in slurries independent of voidage variations. The method is based on the correlation between W and the hydrogen concentration Hsl (wt/wt) of the slurry. Hsl is determined by combining measurements of neutron moderation and ?-ray transmission. Both Wand ash content are determined by combining the above measurements with the ash-sensitive measurement of X-ray backscatter compensated by a measurement of iron K X-ray intensity.The nuclear analysis system, called the SIRO coal slurry gauge, has been proved in a six-week plant trial at the BHP Steelworks washery at Newcastle, NSW. Several probes, each containing a radioisotope source and scintillation detector, were immersed directly into the coal slurry in the feed box upstream from the bank of flotation cells. For 140 samples W, ash and voidage varied in the ranges of 0 to 13 wt percent, 26 to 41 wt per cent and 0 to 4 vol. per cent, respectively. The r.m.s. difference in solids weight fraction, determined by probe measurements and conventional assay, was 0·52 wt per cent. Ash was determined with an r.m.s. difference of 2·0 wt percent in the coal. Better sampling techniques were used in the last half of the plant trial, and r.m.s. differences were 0.35 wt per cent solids and 1·5 wt per cent ash.

Jan 1, 1986

By Jarvensivu M, Ylinen R, Jamsa-Jounela S-L

The paper presents a new integrated system for control of concentration processes. The system is based on cluster-based modelling taking the ore quality into account and a new on-line particle size analyser capable also for reliable measuring of particle size distribution of concentrate. A metallurgical precontrol audit was performed at the Hitura concentrator in order to design the control strategy of the integrated grinding and flotation control. A new analyser PSI-200, was used to the measurement and control of the distribution of nickel in the total particle size range. An expert control system using the cluster model together with a new control strategy for decision of necessary control actions is outlined. The method has been tested to real data from mineral processes. The results are in good correspondence with empirical process knowledge. KEYWORDS: Cluster analysis, expert control, flotation control, mineral processes, modelling, particle size.

Jan 1, 1993

The calibrated thermal IR data of part of Cambay Basin is used to determine surface temperatures and to detect the heat flow. Applying the conductive heat flow continuation technique, the three dimensional configuration of the hydrocarbon bearing reservoir was defined. The zone delineated by the present study coincides with the oil-bearing structures inferred by seismic survey. The results indicate the possibility of the technique as an effective tool in hydrocarbon exploration.

Jan 1, 1986

Introduction The mine winder is an essential element in the mining of ore in deep level mines and therefore requires a high degree of reliability to avoid interruption of production. Failure of any component on a winder may also be dangerous and expensive to repair. The larger the failure the larger the stoppage. The failure of a winder drum is the ultimate catastrophe, not only because of the cost of replacement, but also because of the lead time in procuring a new drum. Today these types of failure are not as common but many failures have occurred in the past and even today many an old winder is con- sidered for a new and often more arduous duty. As far back as the turn of the century a lot of information had been gathered to try and clear up the complexities of the multi- layering effect of coiling rope under tension onto a drum. Before comparing results obtained by various researchers the nature of the pressure distribution between rope and drum due to multi-layering will be discussed briefly.

Jan 1, 1987

Difficult ground conditions in the area planned for placement of vent rises to the surface at the Porgera Goldmine led engineers directing the project to chose blind shaft boring methods of shaft construction from the available alternatives. Zeni Drilling Pty Ltd was first contracted in 1988 to install a group of three closely-spaced, steel lined shafts. The success of these led to an order for a fourth hole in the same group followed by two more, less than a kilometre. away, under a separate contract in 1992. All of the shafts were completed on.schedule to within one day. The only significant difficulty arose during commencement of the last shaft when the strata collapsed trapping the drilling tools and jeopardising the stability of the surface collar pad. The situation was corrected by innovative lining techniques and the project went on to finish on schedule. This paper discusses the application of various technologies associated with the project including aspects of geotechnical input, drilling fluid chemistry, mining engineering and logistics.

Jan 1, 1993

By Pietrobon M. C, Ralston J, Smart St C R

In an on-going study of the chemistry of base metal sulphide flotation, the effect of the inclusion of cyanide in the reagents suite has been studied, with special reference to ore from Pasminco Mining's Elura mine. Cyanide has been variously described as an iron sulphide depressant, a preventor of sphalerite activation and as an activator of galena. In the case described here, the cyanide appeared to act as an enhancer of the galena flotation performance, raising the lead recoveries by 25 per cent but leaving the sphalerite and pyrite responses unaffected. The lead rougher flotation performance with and without cyanide was investigated over a wide range of redox potentials (0 mV to 400 mV SHE). In all cases, the inclusion of the cyanide brought about an increase in the galena recovery and was responsible for a faster rate of galena flotation during the initial stages of the beneficiation. A surface characterisation study (XPS) of the lead flotation stage, with and without cyanide, indicated that the reagent interacted specifically with the galena and pyrite minerals. It was possible to correlate the surface absorption of the cyanide on the lead and iron sulphides with improvements to the flotation performance using the combination of surface spectroscopy and laboratory flotation Testwork.

Jan 1, 1991

By Wiechers HNS

In China the hydrogeological type of solid mineral deposits can be divided into A. Mineral deposits with fissure water; B. Mineral deposits with pore water; and C. Mineral deposits with karst water. The hydrogeological conditions of mineral deposits with fissure water are relatively simple with the exception of a few cases. Mineral deposits with pore water are few but great amounts of ground water can be encountered in the mine accompanied by floating sand or slope failure during the exploitation. Mineral deposits with karst water are complex in their hydrogeological conditions. Enormous inrushes occur frequently in the mines of north China; Karst collapses are a serious matter in the mines of the south; Subterranean river and conduit systems are often encountered in the southwest. This paper will give full discussion on these features and put forward a way of combating and controlling the groundwater problem in accordance with type and feature.

Jan 1, 1988

By J MacNeil, R Dimitrakopoulos

As open pit mining of a deposit deepens, the cost of extraction may increase up to a threshold where transitioning to mining through underground methods is more profitable. This paper provides an approach to identifying an optimal depth at which a mine should transition from open pit to underground mining. The value of a set of candidate transition depths is investigated by optimising the production schedules for each depth’s unique open pit and underground operations. By considering the sum of the open pit and underground mining portions’ value along with the cost of transitioning corresponding to each candidate transition depth, the optimal transition depth can be identified. The optimisation model presented is based on a stochastic integer program that integrates geological uncertainty. As an input, the stochastic integer program utilises a set of several stochastic simulations that represent equally probable scenarios of the mineral resource. This group of simulations describes the uncertainty in the deposit, while the optimiser aims to maximise value based on discounted profits of both the open pit and underground components of the deposit.CITATION:MacNeil, J and Dimitrakopoulos, R, 2014. A stochastic optimisation formulation for the transition from open pit to underground mining within the context of a mining complex, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 363–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Susanto A

As part of the current NERDDC funded project studying Dragline/Hopper/ Crusher/Conveyor systems for overburden removal, an investigation was carried out to assess the feasibility of automating the swing-to-dump phase of the dragline digging cycle in order to main- tain consistent performance of spotting the bucket above the hopper prior to dumping. The study involved design of automatic position controls for the hoist, drag and swing drives and simulation of detailed mathe- matical models of the three electromechanical systems and their associated electrical control schemes. The design of the hoist and drag systems to position the bucket in the boom plane is relatively straightforward. Simulation results show fast and accurate performance, with no evidence of interaction between the two drive systems through the ropes. The design of the swing position control system involves special strate- gies to cater for variable inertia and to damp the pendulum oscillations of the bucket. The use of a bucket pendulum model and variable dynamic compensation embedded within the feedback control loop, along with optimal speed/angle slowdown trajectories, has yielded fast and damped positioning responses under simulation.

Jan 1, 1989

Cerro Matoso (CMSA) in Colombia produces ferro-nickel from lateritic ore containing approximately three per cent nickel, using a Rotary Kiln - Electric Furnace (RKEF) process, in which the calcining of the mineral within the kiln is second in importance only to the smelting of the mineral in the Electrical Furnace. This article discusses the installation and operation of an expert system to control the kiln of CMSA. In the CMSA process, the run-of-mine ore is crushed, homogenised, dried and mixed with a small percentage of coal, before being heated up to 900¦C in a rotary kiln in the presence of natural gas mixed with air in a controlled proportion (air/gas constant ratio). The final objectives of the process are the following: ò To reduce to a minimum the iron and nickel oxides in order to convert these into metallic ions; this is a reduction process to facilitate largely the smelting in the electric furnace. Since the reduction is made with natural gas, it is much more economical than the subsequent complete reduction in the electric furnace, since electrical energy is much more expensive by unit of processed mineral. ò To heat the mineral as much as possible to facilitate the subsequent smelting. ò To eliminate totally the moisture content of the ore. An expert system with fuzzy logic was commissioned in 1994 for the control of the kiln and it has operated with good results ever since.

Jan 1, 1996

By Ohga K, Isobe T

Basing upon many and long practical experiences of gas drainage from coal seam and results investigations on the gas flow through in si-tu coal seam using tracer gases,it became clear that solid coal itself is hardly gas permeable or has extremely low gas permeability. Almost all of gas flows from a coal seam into boreholes through fracture net- works intersecting with them.Primary and secondary fractures in coal seams differ in their size and continuity from place to place according to differences of the coal strength and the stress conditions. A lot of gas can be drained through boreholes which intersect with many and/or wide fractures. A mathematical model for gas flow from a coal seam to a borehole through a discoidal fracture is proposed. From the numerical analyses,the apparent radius of the discoidal fracture in this model is shown to be a good indication of the gas drainage ratio. In addition to this,an atempt to make fractures around a borehole using high velocity water jet(ca.lmm dia.,300-700atm., 100-200 1/min.) is introduced.

Jan 1, 1982

By Finlayson E, Hilyard D

1:100 000 geological mapping of Bougainville Island has resulted in refinement of stratigraphic subdivisions and relationships. We subdivide the sequence into basement Atamo Volcanics (Late Eocene-Early Oligocene), consisting of spilitised pillow basalts, which are overlain unconformably by Late Oligocene-Early Miocene Keriaka Limestone. The latter is unconformably overlain by fine-medium grained volcaniclastics and minor lavas of the Middle-Late Miocene Toniva Formation which coarsens upward and passes gradationally and conformably into the coarsely volcanolithic latest Miocene-Pliocene Arawa Conglomerate. The Kupei Complex, host to the Panguna.porphyry Cu-Au deposit, consists of medium - K20 microdiorites, granodiorites, and andesites intruding Arawa Conglomerate and Toniva Formation. K/Ar isotopic dates on the Kupei Complex range from 4.8-1.3 Ma, and hence overlap the age of the Arawa Conglomerate. We believe that the Arawa Conglomerate consists of mass flow deposits on a volcani- clastic apron surrounding a volcanic edifice above the intruding Kupei Complex.

Jan 1, 1990

By P A. Gow, J L. Walshe, G J. Masterman

The Eocene-Oligocene porphyry belt of northern Chile contains the worldÆs largest accumulation of porphyry-related copper metal. Conflicting models exist regarding the relative importance of strike-slip and reverse faulting during the emplacement of the porphyry and epithermal systems, based on regional studies and also from work at the Chuquicamata deposit. In contrast, at the Collahuasi district, high sulfidation state copper-silver mineralisation was superimposed into the core of the Rosario copper-molybdenum porphyry deposits along normal faults during gravitational collapse of the Domeyko Cordillera. Exhumation of the porphyry environment occurred rapidly during this event, allowing near-surface epithermal mineralisation (<200 m paleodepth) to be juxtaposed into the potassic altered core of the porphyry deposit (estimated depth of formation: 1300 m) in the space of approximately one million years. Mass wasting after major episodes of tectonic uplift provides an effective method of hypogene upgrading of porphyry ores by high sulfidation mineralisation.

Jan 1, 2005

By Guerney P. J

A suspension of finely powdered ferrosilicon in water is the dense medium used in the gravity upgrading of iron ore, diamonds and other minerals. Ferrosilicon can he lost in the plant through corrosion. The greatest corrosion losses occur when

Jan 1, 1997

By Wilson J. R

The main mining method employed at Mt Lyell is sub-level open stoping with a typical extraction level interval of 100 m and sub-level intervals of 30 m. Currently, pillar blasts provide the major portion of broken ore and firings are in the order of 200 000 to 300 000 tonnes while future firings of 500 000 to 300 000 tonnes are planned. Improvement of blasting techniques in these mass firings has been necessary for the following reasons. 1. Extremely wet ground conditions have adversely affected ANFO performance and placed extreme pressure on the charging and priming phases. 2. As pillar blasts increase in size the problems of wet ground conditions are accentuated resulting in very slow loading of wet upholes with cartridged gelignite and unreliable charging of the remainder with ANFO. 3 Fragmentation in pillar blasts has suffered because of the above, result- ing in increased secondary breaking costs and difficulty of extraction.

Jan 1, 1977

By Kallioinen J

This paper discusses different possibilities to enhance coarse particle flotation using forth manipulation and improved flotation cell design. Experiments were carried out in laboratory, pilot and industrial scale ranging from 0.0015 to 100 m3/axle. During the work it could be shown that the conventional idea of one single flotation cell type for both fine, immediate and coarse flotation of coarse and fine particles need different impeller tip speeds and a different froth control objective for effective operation. For optimal operation for coarse feeds the tip speed must be reduced and the froth vertical velocity must be increased to compensate the respective drainage velocity and also the water film thickness must be taken care of. Turbulent eddies below the froth interface should be suppressed. The paper discusses the effects of different froth manipulation variables like froth vertical velocity and froth residence time to the recovery and selectivity. A function has been developed, between the residence time of the froth and the flotation cell's ability to produce an improved concentrate grade as a function of different operating and froth manipulation variables.

Jan 1, 1993