Search Documents

By Fuller P. G

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these Situations.

Jan 1, 1992

By D MacKenzie

The Rise & Shine Shear Zone is a shallow-dipping Cretaceous late metamorphic shear zone formed in a compressional environment. The Shotover mineralised system is dominated by normal faults with well-defined vein systems that cut across Miocene schist folds and faults related to the inception of the Alpine Fault. Despite the geological differences between these mineralisation systems, they share many common features of hydrothermal alteration that have resulted in disseminated gold in altered sheared schist. The most distinctive feature of both systems is the abundant ankeritic carbonate that has formed from decomposition of metamorphic chlorite. Excess iron from this alteration reaction combined with hydrothermal sulphur to form sulphides that host the disseminated gold. The chlorite decomposition reaction was reversed in the latter stages of both mineralisation systems, and this was accompanied by further gold emplacement in the Rise & Shine system.   Both alteration systems involved initial decomposition of metamorphic albite, followed by deposition of albite as a vein mineral in the latter stages. The fluid flow that yielded the disseminated gold was controlled by microshears that pervade host schists, in strong contrast to many Otago Schist vein systems where host rock alteration is absent. The ankeritic alteration in the Shotover and Rise & Shine mineralised systems has increased the volume of mineralised rock, and may have made suitable targets for large-tonnage, low grade gold deposits.

Jan 1, 2007

By Z W. Orndorff

Excavation through sulfidic geologic materials during construction activities has resulted in acid rock drainage (ARD) related problems at numerous (>40) locations across all five geologic regions of Virginia, USA. Potential acidities ranging from >100 to develop a statewide sulfidic materials risk map; document ARD impacts to soil and water quality and engineered structures; and develop methods to assess site-specific risk potentials within a given highway corridor. A statewide sulfidic materials GIS risk map was developed based upon the state digital geology map which assigned four levels of relative risk to all mapped strata based upon predicted lime requirements and probabilities of encountering highly reactive materials. Non-highway construction activities have also routinely disturbed sulfidic materials, and a recent airport project in northern Virginia resulted in over 150 ha of extremely acidic (pH 45 mg/L) run-off from this site heavily damaged a receiving stream, partially due to the fact that it dissolved the galvanised steel water control structures in stormwater detention basins, leading to direct discharge of run-off and sulfidic sediments. The airport area was treated and revegetated in 2002 with a combination of lime-stabilised biosolids, straw mulch, and acid-tolerant grasses. Water quality in a receiving second-order stream quickly responded to the treatment, but some release of N was also noted as a secondary effect. Collectively, these results point out the importance of accurately assessing the potential for excavation of sulfidic materials in construction environments, and the necessity of developing toxic materials handling strategies similar to those employed in mining environments.

Jan 1, 2003

By Edwards R

Greater efficiency of capture of minus 6 mm to fine micron size particles of free gold is achieved with the Knelson Concentrator. The development, principles of operation and recent innovations relating to this enhanced gravity concentrating device are described by the inventor, followed by a description of application and consequent economic benefits in low grade alluvial gold deposits by a large scale user of Knelson Concentrators in the Northern Territory of Australia.

Jan 1, 1990

By Raymond G. F

Geostatistics - a tool used by geologists and mine planning engineers to estimate grades and rapidly evaluate alternative mining strategies has reached an advanced stage of development for the silver-lead-zinc orebodies at Isa and Hilton Mines. Geostatistics has been used for over a decade in the massive copper orebodies but the stratiform lead-zinc orebodies are much more complex and provided a completely different set of challenges. Recent increases in computer processing speed and power provided by the Integrated Mine Planning System (IMPS) has aided the development of the geostatistics package. Also the formation of a project team and the subsequent in-house development which has drawn together the expertise of geologists, engineers and system analysts has contributed significantly to the success of the project.The most important feature of any approach to modelling the lead-zinc orebodies is that the kriging search must consider estimate and sample points according to their positions relative to bedding surfaces. By transforming co-ordinates as perpendicular offsets from a plane representing the local strike and dip, it is possible to elongate the ellipsoidal influence to parallel bedding. By interactively modelling surfaces using CAD facilities and then specifying these surfaces as 'hard' or 'soft' boundaries, the geologist has complete control over the kriging process.

Jan 1, 1993

By Singh DP, Singh TN

The present study attempts to critically review the pillar-design as required by Coal Mines Regulations of India vis-a-vis latest rockmechanics formulae. Equivalent material modelling was the approach adopted for testing the safety and stability of the pillar sizes predicted by various formulae. Two parameters, considered here for calculating pillar sizes was the stresses acting over the pillars and the strength of the pillars. Stresses acting on the pillars were calculated by the tributary area method. Based on the studies of Coates and Hustrulid, the stress obtained was reduced by 40 percent. For calculating the strength of the pillars, three formulae, namely Holland and Gaddy, Salamon and Munro and Central Mining Research Station, India, were used. The pillar widths were then determined by equating the product of recommended factor of safety and pillar stress with the pillar Strength.

Jan 1, 1992

By G MacSporran, I Sheppard

The practical application of LaneÆs theory on optimum cut-off grade policy has to date proved difficult for selective stoping in large-scale underground mining. The key to determining an optimum cut-off grade is the ability to rapidly perform complex mine layout designs combined with rapid output of multiple potential schedules. This paper describes aspects of the detailed investigation into estimating a practical static cut-off grade for the two main orebodies in Mount Isa MineÆs Enterprise Mine. Rule based automated scheduling software was used to evaluate thirteen different stoping layouts (including design infrastructure and capital development) of the Enterprise MineÆs two main orebodies, with over 200 schedules generated. The investigation illustrates the application of commercially available software to solve the problems of generating multiple cut-off grade stope designs and achieving the otherwise insurmountable task of rapidly generating and valuing multiple scenarios for each stoping layout. Each scenario was evaluated using modelled net cash flows of the mining, concentrating and smelting operations of the company and calculating NPV. The cut-off grade for each orebody was selected based on the cut-off grade that achieved maximum NPV û with an appropriate production rate. Underground mine scheduling is a complex task involving the adherence to a number of simple scheduling rules and the balancing of several competing drivers. The study also found that: while each scheduling rule itself is simple, the compounding complexities of their interaction preclude manual scheduling from being a realistic option. there is a maximum sustainable rate of production possible for any given stoping layout, and that the actual maximum production rate is also a function of the required number of years of sustainable production. the optimal cut-off grade was different for each orebody û a recognition of the impact of the different characteristics of each orebody.

Jan 1, 2003

Froth flotation is widely used for the separation of particulate materials in the world. It is a complex process whose operational behaviour in process plants is difficult to predict. A comprehensive phenomenological dynamic flotation model was presented at the 1982 IMPC. This model uniquely linked the particle/bubble interactions and water transport phenomena to the flotation cell hydrodynamics. The model was used as a dynamic framework to analyse and develop process optimisation strategies. New developments in mineralogical characterisation, real time information management systems and data validation simplify the implementation of flotation technologies for mine to mill grade recovery optimisation. With recent developments in software programming, dynamic simulation enables process engineers to develop process alternatives interactively. This paper presents such an implementation of current process analysis tools and an updated froth flotation dynamic model. It demonstrates how this new environment can be used to improve our technological knowledge of flotation, eg alternative bubble/particle attachment and detachment microprocesses can be incorporated. The dynamic flotation model has several manipulated variables (such as feed flow rate, per cent solids, aeration, wash water flow rate, frother flow rate, specific power energy (impeller speed/delta pressure), cell geometry and tails flow rate) and evaluates the dynamic effects of these variables on grade and recovery.

Jan 1, 2005

By D Cotnoir, Q Liu, D Richard, M Ourriban

The difficulty in fine particle flotation has been attributed, among other things, to a low bubble-particle collision efficiency. Many technologies have been developed which aim at increasing bubble-particle collision efficiency, either by generating micro bubbles or by enlarging particle sizes. However, commercial applications of these technologies are limited. Over the last five years COREM has been actively testing fine particle froth flotation technologies with the objective of commercialisation. Several fine particle flotation technologies, such as dissolved air flotation, electro-flotation, floc flotation, selective flocculation-flotation and carrier flotation, were tested on both single minerals and ore samples in order to identify the reasons that prevented these technologies from being used on a commercial scale. It was found that the two most noticeable factors that prevented the successful application of these technologies were: Mechanical entrainment of fine gangue minerals. This was a general problem in fine particle flotation, but was aggravated by these technologies that either generated micro bubbles or enlarged the sizes of hydrophobic particles. Oxidation of (sulfide) minerals that resulted in hydrophilic oxidation product coatings. The oxidised fine particles could not be recovered by these fine particle flotation technologies effectively. Solutions to the two problems, ie gangue entrainment and fine particle oxidation, were proposed and tested. It seems that polymeric depressants with both depression and flocculation functions could significantly reduce gangue entrainment, and hydrophilic surfaces of oxidised fine particles could be modified by high intensity conditioning or controlled sulfidisation, thus increasing the recoveries of fine valuable minerals. The improved fine valuable particle flotation and reduced fine gangue entrainment along with fine particle flotation technologies resulted in much improved flotation separation of fine particles.

Jan 1, 2005

Two independent sets of observations from rifted con-tinental margins suggest a way to reach a quantitative under-standing of how the topography of rifted margins erodes. First, a prominent erosional escarpment, which demarcates an elevated, inland region of low relief from rugged, deeply-incised terrain on the seaward side, is the main feature of the geomorphology of many rifted continental margins. Second, apatite fission track ages from the southeast Australian and southwest Saudi Arabian margins scatter about constant Paleozoic ages over the higher elevations inland from the escarpment, but decrease systematically seaward of the escarpment to near-rifting ages approaching the coastlines. We have developed erosion models based on conservation of mass principles to explain these observations. These models seek to explain the "rejuvenation" of erosion at the time of rifting, initiation of the observed erosional escarpment, and its migration inland with time at a rate on the order of 1 km/10 yr. We find from the modeling that erosion at rift flanks and passive margins is fundamentally a non-linear pro-cess. The erosional development of passive margin topogra-phy has much is common with travelling wave solutions to non-linear diffusion-type problems, and to self-similar sto-chastic processes, such as diffusion-limited aggregation. We suggest that the fission track data record the thermal effects of erosional unroofing at rift flanks and passive continental margins. Models intended to explain the erosional develop-ment of continental margins must explain both the geomor-phology and the fission track observations as well.

Jan 1, 1990

Grade control aims to deliver quality tonnes to the mill via accurate definition of ore and waste. It comprises data collection and interpretation; local reserve estimation; supervision of development and mining; and stockpile management. The foundation of all grade control programs should be that of high quality sampling supported by geology. The requirement for quality grade control samples has long been recognised, where they should be representative, unbiased, safe and operationally timely. Underground sampling methods include chip and channel samples; grab samples; and drill-based samples. To achieve quality samples, collection techniques employed should minimise delimitation, extraction and preparation errors. Grade control staff should be well-trained and motivated, and mining staff should understand the need for grade control. This paper reviews grade control sampling methods and presents recommendations for best practice and minimisation of sampling errors.

Mar 1, 2010

A nuclear technique utilising the gamma-ray resonance scattering process is used at Isa Mine for the determination of copper in drill core and bulk mineral samples. The Copper Bulk Analyser (CBA) provides quick and accurate non-destructive copper analysis of drill core at costs two to three times cheaper than conventional chemical techniques.The almost immediate availability of sample results enhances the efficiency of the mine geologist in the duties of grade control, design of diamond drilling programmes, and input to planning. The unit has proven to be a reliable and accurate production tool requiring a minimum of technical support.

Jan 1, 1990

By Wood CJ, Davis JJ, Askew H

A dynamic model of a dense medium circuit has been developed and tested against plant data. The model shows the response of the circuit to both controlled (changes in specific gravity set point or changes in circuit coal feed rate) and uncontrolled changes (changes in raw coal moisture, loss of raw coal feed) in operating conditions. The model is built up from dynamic models of the individual sumps, pumps, pipes, splitters, magnetic separators and automatic controllers in the circuit. The model can be used for design of automatic control loops and for investigation of possible process modifications such as changes in water addition points. This paper describes the model construction, the testing of the model against actual plant data and gives some examples of its use in investigating plant response to changes in operating conditions.

Jan 1, 1978

By Tomlinson R. C

There are two main aspects of coal preparation to which the operational Research Executive of the National Coal Board has applied computer models. The first is in the planning of preparation plants and the first part of this paper discusses Simprep, a computer package that was designed to help on these calculations. The other is the development of control schemes to improve quality control, and the second part of the paper deals with the development of simulation techniques for this purpose.

Jan 1, 1977

By Artieda JJ, Catalina JC

- The aim of this paper is to analyse the possibilities of applying signal processing and artificial vision techniques to the ore sorting problem. In order to overcome the limitations imposed by the classical approach to the problem, which essentialy cons

Jan 1, 1985

It is indeed a privilege and honour to deliver the keynote address at this 15th APCOM symposium. APCOM has played a significant role in my own career and I am sure in the careers of many of the thousands of other participants over the years since its inception as a short course on "Computers and Computer Applications in the Mineral Industry" at the University of Arizona in 1961. The technical papers and addresses presented at the 14 past symposia provide an imposing record of sustained pro- gress and achievement in the field of computer applications. I will not attempt to analyse this technical side of APCOM but rather endeavour to provide you with a broad popular perspective of the road travelled to date and that lying ahead of us. The name of the series of symposia has changed from time to time, with titles such as Mathematical and Statistical Techniques, Mining and Exploration, and Decision Making being used at various times until in 1972 the name APCOM was coined and the present loga designed by the South African organising committee for the 10th symposium. It can conveniently be accepted as standing for:

Jan 1, 1977

The Golden Pig Mine is wholly owned by Bunnine Operations Limited and is located in the Yilgam Goldfields at Southern Cross, Western AustraliaThe paper briefly describes the geology and history of the operations. Mining is by shrink stoping, both hand held and mechanised. Advantages and disadvantages costs of the mining system are discussed.

Jan 1, 1993

By Erepan P. C

Flash flotation technology was introduced by Outokumpu in 1985. Considerable success was achieved in other plants with similar operations to OTML. Conclusions from site visits and amenability tests performed on plant samples were that the OTML

Jan 1, 1997

By Royle A. G

The paper describes a geostatistical structural analysis of an 80 square mile lease of the Athabasca tar sands. Each step of the analysis is presented with the ultimate objective of condensing the principal structural characteristics of the chosen regionalised variables into the opera- tional form of the variogram model. The variogram model is then used to form kriged local and global estimates, with the corresponding estimation errors.

Jan 1, 1977

Precipitation of inorganic compounds or metals from aqueous solutions can either be physical (crystallisation) or chemical in nature. Chemical processes are varied; they may be due to hydrolytic action, due to ionic interaction, or due to reduction (ie transfer of electrons). Transfer of electrons in reduction processes may take place homogeneously or heterogeneously. In the first case it may be ionic or nonionic in nature. Heterogeneous processes may be electrochemical or electrolytic. Examples of interest to hydrometallurgy are given.

Jan 1, 1993