Search Documents

By Thomas G. A

THE irregularity of the Mount Morgan (Queensland) ore body presents problems other than those only of mining. For irregularity of outline is coupled with irregularity of grade, and the ore varies so rapidly from profitable to non-profitable, and fromhighly siliceous to highly pyritic, that the task of estimating quantities and values of ore reserves is manifestly rendered a difficult one, while the actual disposal of the broken ore demands constant supervision.Four classes of ore are handled. The oxidized ore, cheaply mined and cheaply treated, is obtained by quarrying from the top of the mountain. Below the 315-ft. mine level (measured from the original summit) sulphide ore comes in, and this is divided into siliceous sulphide ore (too siliceous for economic smelting), sulphide ore suitable for smelting, and ore too poor either to be smelted or to be treated by wet process with the siliceous ore. It is with these three latter descriptions of ore that this paper principally deals.Although the output from many stopes in the mine may usually be presumed beforehand to be either smelting or wet-treatment ore, yet it is never safe to take this for granted, and constant assaying is necessary. At the same time the ore merges from one class into...

Jan 1, 1911

A shift in the present day oil exploration scenario from West Coast can be foreseen keeping in mind peak of exploration in Cambay Basin and fast pace of development in Bombay High and its associated fields by the end of this century. Shifts in exploration from structural traps to stratigraphic traps, techno- logical development to drill in deep waters, improving economic situation for oil ventures and proven oil and gas potential of East Coast basins suggest that Indian oil explorat- ion scene will be at its peak along east coast during early 21st century. Hydrocarbon shows in Poonch and Jawalamukhi in Punjab Basin, improvements in drilling to greater depths, better seismic data aquisition, good source rock potential of Subathus and its equivalents and large geologi- cally mapped structures will reopen new avenues for explorationists. Not much exploration effort has been put up so far in Ganga Basin. Keeping in mind size of the basin, sedimentary thickness involved, presence of algal matter deposited in shallow marine environment & higher hydrocarbon indications warrant active exploration. Gondwanas in India having such a large sedimentary area can not be ignored keeping in view generation and production from the non marine sediments of Kenya, Chad, Sudan, Gadon and China. Gondwanas become all the more important in view of gas production from their equivalents-Karoos in Ethiopia and South Africa. In all, above mentioned changes can be predicted in Indian oil exploration scenario during 21st century.

Jan 1, 1986

Direct smelting of copper in a single vessel has long been the extractive metallurgist's dream. Such a process offers the important alvantage. of (i) maximum use of the energy available from oxidizing the sulphur and iron of the concentrate: (ii) restriction of SO2 emissions to a single constant-strength source; (iii) minimum materials handling and (iv) elim-ination of at least one process step. Extensive developmental work was carried out in the 1960's and 1970's to implement such single-step processes. Some of the processes reached the prototype stage and it appeared that copper smelting technology was on the thresthold of a new, efficient, minimum-pollution era. Since that time, however, the forward thrust has slowed and single-step copper smelting is still a process of the future.The paper describes the potential advan-tages of single-step smelting; its history and current status; and the reasons why it has not been adopted industrially. It concludes that the potential benefits of single-step smelting are powerful and that many of the difficulties encountered in the 1970's will be overcome in the 1980's.

Jan 1, 1985

The Telfer Underground sublevel cave (SLC) Operation is located approximately 850 m below surface. The cave was designed to propagate through an old decline which was initially used to monitor the cave. There was a requirement to install air blast plugs at two locations in the old decline in order to isolate any potential air-blasts from the active workings in the event of the rock mass collapsing into the cavity. There was a further requirement for an air-blast plug in another section of the mine where there was a risk of the cave intersecting an old workshop and providing an air-blast pathway through an abandoned incline. The design criteria for the plugs was that they should withstand the design air blast loading, be free draining, cost effective and easily constructed with the mining expertise available on site. A plug consisting of grouted mullock was considered robust and least challenging to construct. For the purpose of estimation of maximum air pressure on plugs, it is supposed as a worst case that the rock above a cave falls as an airtight piston onto the top of a muck pile, forcing air into it and also mine workings intersected by the cave. Airflow through the muck pile is governed by Ergun's equation for turbulent flow. In a time-stepping integration scheme, transient air pressures and velocities are calculated according to equations of thermodynamics, in the cave and at intervals along intersected drives by means of a finite difference spatial discretisation. The ability of plugs to withstand computed pressures is assessed by finite element elastoplastic analysis. This paper outlines the rationale for potential air blast loading, calculation of transient air pressures, plug design and analysis of plug behaviour. The plug construction method is also discussed.

Nov 25, 2010

Maximising margins in today's competitive international commodity markets demands superior productivity. This requires more than simply selecting the best equipment. It requires efficient production and commercial processes together with management systems recognised as international best practice. This paper introduces an integrated way of working that includes management systems for successfully changing work practices and attitudes, developing managers and increasing accountability. It provides an improvement methodology that includes systematic involvement of people in true continuous improvement of processes for maximising productivity and safety while minimising costs. Even though the principles are proven in all industry sectors worldwide, they are not always used correctly. This paper provides examples of traditional performance measurement systems to show how managers miss opportunities to control and improve both production and supporting service processes. It also describes the basic methodology for correct use of the principles and provides examples of correct implementation of modem systems in mining. The charts from actual mining case studies will be elaborated upon in the conference presentation. This paper's main aim is to provide background material for the presentation by introducing integrated principles for building best practice management systems for superior productivity and safety - for higher margins.

Jan 1, 1996

Black coals occur in most of the major sedimentary basins in Australia. In addition to the better known Permian coal occurrences of the Sydney, Bowen, Oaklands and Galilee Basins, coals of Permian age occur in the Arckaringa Basin in South Australia, the Bonaparte Basin in Northern Territory and the Collie, Perth and Canning Basins in Western Australia and the Tasmania Basin in Tasmania. Coals of Triassic age occur in the Ipswich Callide and Tarong Basins in Queensland, the Tasmania Basin in Tasmania and the Leigh Creek area in South Aus- tralia. Coal bearing rocks of Jurassic age occur in the Mulgildie Basin and Maryborough Basins in Queensland and in both the Queensland and New South Wales portions of the Clarence Moreton Basin and Surat Basins. They also occur in the Perth Basin in Western Australia. Rocks of Cretaceous age known to contain coal occur in the Styx, Maryborough and Laura Basins in Queensland, the Gippsland Basin in Victoria and both the Queensland and New South Wales portions of the Surat Basin. The coal measures have been deposited in a variety of sedimentary environments and the coals vary widely with regard to thickness, extent, banding characteristics, maceral and ash content. However, they are generally of low rank and most are suitable only for steaming.

Jan 1, 1975

By Nickson NM, Lancucki CJ

X-ray diffraction and differential thermal methodshave been used to determine the mineralogy of some clays used by the heavy clay industry in the Adelaide area. A detailed analysis has been made of the mineralogy and. particle size distribution of eighteen samples from beds' in two pits in~the Recent seaiinents in the Adelaide plains, of six white clays.: developed from the weathering of the Adelaide series of `sediments and, of ,four -Recent alluvial clays from a pit in the Mount Lofty ranges south of Adelaide. Structural clay products 'in the Adelaide area are manufactured from mixtures of these clays:, so the mineralogy and particle size distribution have been determined of eighteen clay mixtures used to make red bricks, cream bricks,. facing bricks, pipes and tiles. Knowledge of this mineralogy is important in understanding the ceramic behaviour of the clays.

Jan 1, 1963

The paper presents an overview of the mining industry of Papua New Guinea. Although the Bougainville problem is still unresolved, new mines like Ok Tedi, Misima and Porgera, which have come on stream during recent past, have raised hopes of sustained growth period in the industry. Kutubu Oilfield is also being developed in the Southern Highlands and the oil production has commenced from July 1992. Government revenue from these mega projects will increase five-fold during 1993 and 1994. A new mine which is being planned is the fabulous Lihir Deposit, on an island renowned to be full of gold. Gold occurs within a volcano which still contains high temperature ground water because the system which created the deposit is still geothermally active.In Papua New Guinea, problems of environmental management are far easier to tackle than those of a socio-political and economic nature involving compensation payments to the landowners and the distribution of royalties and taxes between the national and provincial governments. At the socio-political level, the country has not been able to resolve the problems of land rights versus mining rights. Whenever mining starts in a big way, it raises people's expectations to a very high level, which then becomes the focal point of dispute between landowners, provincial governments, national government and mining companies. A new system called 'Forum' has been tried to bring all parties together and son out the issues. The system appears to be working well in new mines like Ok Icdi, Porgera, Misima and Kutubu Oilfields.

Jan 1, 1993

The eastern third of Australia contains an unrivalled Phanerozoic rock record generated by the regional interaction of Gondwanaland with the Pacific and by the global effect of the 400 m.y. Pangaea - Panthalassa cycle. Between the latest Proterozoic (600 Ma) breakup of Proto-Pangaea and the mid-Carboniferous coalescence of the dispersed continents in Pangaea, the Lachlan and Thomson Foldbelts accreted to the craton by Mariana-type (backarc basin) and Chilean-type (continental margin) subduction from eastward jumps of the Palaeo- Pacific rim. Further jumps of the rim of the Permian and Mesozoic Pacific, now expanded to Panthalassa, accreted the New England Foldbelt to the craton. An Early Permian rift basin was succeeded by a Late Permian to mid-Triassic foreland basin which extended between the craton and the foldbelt behind the 10000 km Panthalassan rim, from the Bowen Basin of Queensland to South America, and was host to the productive coal measures of eastern Australia, as the succeeding Jurassic and Early Cretaceous foreland and epicratonic basins included the coal measures, hydrocarbon reservoirs, and aquifers of the Great Artesian Basin. The magmatic arc on the Australian margin ended after the mid-Cretaceous uplift along the Queensland coast that initiated southwestward drainage from the high Pacific rim. The Chilean-type subduction that had prevailed since the Devonian was superseded shortly afterwards by Mariana-type subduction with the successive generation of the back-arc basins of the Tasman Sea, Coral Sea, and other southwest Pacific basins by the migration of the island arc to its present position 2500 km eastward of Australia.

Jan 1, 1990

The Mesozoic intrusive rocks in southeastern coastal China can be divided into three intrusive suites, and they can be brought into corresponding with four cycles of volcanic activity. This paper describes their time-space relation with volcanic rocks, and their geochemical characteristics. Data from the Mesozoic volcanic-intrusive. complex rocks in Eastern Zheijiang, Eastern Fujiang and Eastern Guangdong show distinct regional differences, both within and tectonomagmatic activity regions. The southeastern coast of China involves four tectonomagmatic activity regions. They have many differences on the nature of magma source regions, activity patterns of magma, time-space distribution, petrography and petrographic facies association of volcanic and intrusive rock and mineralization.

Jan 1, 1990

By Wright S

Single pellets of mixed lead-zinc concentrate containing up to 20 % lead were roasted in the temperature range of 800-1100¦C. Variables studied included pellet size (from 9-8 to 3-2 mm diameter), gas flowrate past the pellet (from 0.05 to 5 ms t), composition of the atmosphere and the effect of additives such as zinc oxide and silica. After defined periods of time, the pellets were removed from the furnace, quenched and submitted for chemical, XRD, SEM and microprobe analysis. The oxidation of the zinc sulphide followed a shrinking core model. Temperature measurements showed that very high pellet temperatures were experienced at the start of an experiment but after 5-10 minutes these approached a constant temperature. The lead loss from the pellets was then constant with time. Thermodynamics predicted the presence of two bands of lead material in the reacted layer of the pellet. These were found in practice. The lead loss from the pellet occurred from the outer oxysulphate layer via the vaporization of lead oxide polymers. The vapour pressure of PbO, and the loss of lead, was dependent on temperature and bulk gas concentrations of SO2 and 02. At 1100¦C the addition of silica greatly reduced the loss of lead from the pellet. Physical factors such as pellet diameter and gas flowrate past the pellet affected the particle dynamics. These results were found to vary in accordance with the predictions of the Froessling equation.

Jan 1, 1989

By Selischop F, Tredoux M

The distribution of platinum-group elements (pGEs) has been investigated in matte and slag samples from Waterval Smelter (Rustenburg Platinum Mines). The study showed that a strong preference of PGEs for alloy phases in matte represents a concentration mechanism that commenced in the furnace but can be considered a continuum from natural processes. Metal losses to fayalite (converter) slag occur by matte entrainment due to the mechanical capture of liquid sulphide droplets from the matte layer, and the exsolution of dissolved metal sulphide resulting from changes in the oxidation state of the slag. The latter is comparable to immiscible sulphide in basic magmas. However, the observed distribution of PGEs shows enrichment in metal phases of the matte. A mechanism is proposed whereby naked PGEs in silicate melts coalesce to form clusters which are stabilised by surface attachment of sulphur atoms. This envelope acts to 'draw the cluster into sulphide melts. Small particle melting effects permit PGE clusters to remain as liquids at magmatic and smelter temperatures.

Jan 1, 1994

By B J. Wilde

Evaluating the resources and reserves in a mineral deposit requires many interdependent subjective decisions. The decision of stationarity is arguably the most important. This decision includes: the choice of domains that subset the entire deposit, modelling the boundaries of each domain, and understanding and considering the nature of the contacts between domains. Reasonable choices are made in consideration of the geological context, the available data, the goals of the study and the available resources for the study. This paper reviews aspects of the decision of stationarity in modern resource assessment with a focus on quantifying uncertainty and using numerical/statistical tools to help the geomodeller. The use of volume/distance functions to quantify uncertainty in domain limits is particularly important and is presented in detail. The use of contact plots provides help with the continuity of grades across domain boundaries. Realisations are not assembled as a branching combinatorial of all possibilities, but as a set of realisations that provide a measure of uncertainty. This paper amounts to a definition of stationarity for modern resource assessment.

Sep 26, 2011

By Kobayashi M

Particulate chalcopyrite samples (78 ~ 98 mole per cent chalcopyrite, screen size fraction from 710 to 250 µm) were prepared by crushing and sieving lump ore samples from 12 locations in the Mt Isa Mine. Measurements of thennoelectric power (which does not involve the passage of a current) were made using a packed bed that was compressed by loading with a weight and placed in a temperature gradienL Details of the apparatus are described.The effect of particle size was investigated by preparing 12 fractions, with mean particle sizes ranging from 605 to 2.2 µm, from one of the ore samples. Values of thennoelectric power decreased with both increasing particle size and loading pressure; however it remained fairly constant for particle sizes above 80 µm, when loading pressure exceeded 3.3 MPa.Measurements of the chalcopyrite samples gave an average value of -260 JlV/K (-248 ~ -268 µV/K) for nine samples and about -290 µV/K for three samples, showing that these samples were all n-type semi-eonductors.

Jan 1, 1990

A failure of the Pit IA highwall in July 1989 led Newcrest Mining Ltd's Telfer Gold Mine to commence underground operations approximately 12 months ahead of schedule. The failure presented four major challenges to management: 1. how to maximise the recovery of the Middle Vale Reef (MVR) in the open pit: 2. how to minimise the risk to personnel involved in the extraction of the remaining open pit ore; 3. how to avoid disruption to ore supply: and 4. how to maintain a permanent and safe means of accessing the underground operations from the base of the pit. The risks associated with meeting these challenges were minimised through the installation of a complex network of real time slope monitoring equipment. These monitors were connected to an alarm system which was combined with detailed operational procedures to be carried out in the event of a highwall alarm being triggered. The accuracy with which the risk of failure has been managed was demonstrated recently when the onset of a second failure was initially identified some 13 months prior to its ultimate collapse in October 1992. The location, timing and size of the failure was able to be predicted allowing appropriate precautionary measures to be taken to ensure safety of access to the underground portal and pumping equipment in the base of the pit. This paper reviews the sequence of events leading to both the July 1989 and October 1992 failures of the Pit 1A highwall and the monitoring equipment and procedures used to identify, quantify and manage the risk to personnel operating in the base of the pit.

Jan 1, 1994

By Mostyn G

In the last three decades various theories have been presented to allow the estimation of the force required to cut rock. These have generally relied on an hypothesised mechanism of chip formation.The paper presents results of an experimental program completed on an unjointed artificial rock in which the force and chip geometry were measured during deep cutting with a quarter scale bulldozer tyne. The program included various depths of cut and artificial rock of varying strength. The experimental results are compared with predictions based on three expressions for cutting force. Generally the measured forces are within the range of those predicted but none of the methods predicts the cutting force with any accuracy. It is considered that the discrepancies are due, in part, to the fact the that actual shape of the chip formed in deep cutting is quite different to that assumed in developing the theories and thus the theories cannot be expected to predict the cutting forces. It is concluded that Evans and Nishimatsu's theories predict lower bound estimates of the horizontal cutting forces. Deliac and Fairhurst's approach appears to over estimate the forces required to cut rock. New methods of prediction are required based on the observed mechanisms of failure.

Jan 1, 1993

By W J. Botha

The Palaeoproterozoic Transvaal Supergroup in the northern Cape Province of South Africa hosts high grade (>60 per cent Fe) hematitic and specularitic iron and manganese mineralisation. The mineralisation is primarily exposed along the western margin or in the central part of a major interference fold structure known as the Maremane dome. The bulk of South AfricaÆs iron ore production is currently provided by two active mines, Kumba Resources megaton Sishen iron ore mine on the northern end of the dome, and the smaller Assmang Beeshoek mine on the southern closure. The undeveloped Sishen South deposit, which contains ~400 Mt of high-grade hematite ore, is located approximately 9 km towards the southwest of Postmasburg. It forms a linear extension of the Beeshoek mine and as such contains comparable laminated, breccia and conglomeratic iron mineralisation. The Transvaal Supergroup sediments were deposited in two distinct fault-controlled basins on the Archean Kaapvaal craton. Basement rocks in the western Griqualand West basin are formed by a carbonate platform sequence (Campbellrand Subgroup), which is overlain by a thick sequence of banded iron formation of the Asbesheuwels Subgroup. A major unconformity separates these rocks from the red-bed Gamagara Formation, which is correlated with the base of the Olifantshoek Supergroup. Diamictites and lavas of the Postmasburg Group have been thrust over these units from the west. The mineralisation process is related to regional scale supergene iron enrichment of Kuruman banded iron formations along the unconformity. During regional tectonism associated with the Kheis orogeny (2400 - 1700 Ma) the Maremane dome was uplifted, and the basal dolomite units thus exposed to erosion and karstification. The overlying banded iron formations collapsed into karst sinkhole structures where leaching of silica and enrichment of hematite occurred. Although the exact mechanism of the mineralising process remains unclear, karstification preserved components of the original concordant laminated and massive ores. These ores were subsequently eroded and deposited as conglomeratic and gritty ores down-dip of the Maremane dome in alluvial fan systems. A thin veneer of recent calcrete or Tertiary Kalahari clay beds masks the subsurface geology and most of the orebodies, thus ground geophysical gravity surveys proved excellent exploration tools to penetrate the surficial cover. These surveys were used extensively for delineation drilling and to deduce the subsurface geology and structural development of the area. Finally Sishen South orebodies were modelled with ModelVision software in an attempt to obtain an exploration template for the surrounding area.

Jan 1, 2005

Blasting is an essential component of most mining operations, and is used to reduce the rock mass to a workable size distribution, as well as to create stable openings and pit walls. Frequently, there is little difference between the designs of blasts to achieve these two functions, though more advanced operations have developed different designs for these very different functions. To assist in the appreciation of how blasting practices can impact on the stability of rock openings and pit excavations, this paper reviews the role of high pressure explosion gases on final block stability. It is assumed that the stability of all surface and underground excavations are, to a greater or lesser extent, controlled by the interaction between discrete rock blocks. Typically, these blocks will be defined by either natural, or excavation induced, jointing.

Jan 1, 1999

By Amelunxen R, Finch JA

Flotation columns represent an important addition to flotation practice. Columns have largely replaced. conventional machines in molybdenum cleaning in Canada. Columns have been successfully tested on bulk copper/molybdenum cleaning at Gibraltar Mines Ltd. A rougher cleaner/scavenger cleanercombination was shown to be capable of giving higher grades and recoveries compared with three stages of conventional cleaning. A control strategy for the columns has been developed. An interaction between gas hgldup and wash water rate has been exploited to control performance.

Jan 1, 1985

By E S. Weiss, S P. Harteis

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) has conducted full-scale explosion experiments, to evaluate the strength characteristics of various seal designs, used for safely isolating worked-out areas in underground coal mines. Large-scale explosion tests conducted within the multiple entry section of PRLÆs Lake Lynn Experimental Mine (LLEM) is currently the only accepted test method used by the Mine Safety and Health Administration (MSHA), for deeming a seal design suitable for use in American mines. These explosion tests are labour intensive, expensive to conduct, and can interfere with other critical underground safety and health research programs conducted by NIOSH. The PRL has developed an alternative seal evaluation method, based on a hydrostatic pressure loading concept, that can facilitate the in situ testing of seals in an operating mine. Two chambers within LLEM and one within PRLÆs Safety Research Coal Mine (SRCM) were used for hydrostatic pressure loading various seal designs. The results from these chamber tests compare favourably with those from the large-scale explosion tests in the multiple entries. In addition to testing seal designs at the required 20 psi static pressure level, the chamber test approach also allows for the determination of the sealÆs ultimate design strength. Size-scaling relationships for predicting the strength of seal designs as a function of entry size are also presented.

Jan 1, 2005