Search Documents

Tunnels are being built around the world using TBMs and prefabricated segments or in situ concrete as linings. Clients demand high quality of these linings to guarantee a long-term stability and density of the tunnels. This paper describes the development and the use of segmental lining systems, including joints, important design criteria, installation procedures, possible mistakes and consequences, repair works and final results for different sites in Europe and around the world. The experience on these sites shows that damages may occur, if some essential aspects are not considered. These aspects include:parameters of the TBMs and back-up equipment such as fixation of jacking rams, movement of the back-up on the lining or ring reformer;parameters of the segments such as quality of moulds, quantity of reinforcement or structure of the joints; andparameters of the tunnel drive such as advance rate, ring-gap grouting or experience of the tunnel crew.All these aspects have to be considered very carefully in detail to get a good lining accepted in total.

Jan 1, 1999

By M, C A. RosiFre, R C. Figueiredo e Silva

Jaspilites and underlying basalt contacts of the Archaean volcano- sedimentary Grpo Parß Group, Carajßs, host giant iron mineralisation in the ~100-km long, E-W trending Carajßs fold. Preliminary, unpublished geochronological data point to a Palaeoproterozoic mineralisation event. Geochemically, jaspilites are typical volcanogenic banded iron formations. Basalts exhibit evidence of spilitic seawater interaction. Iron-associated hydrothermal alteration of mafic rocks was induced by fluid infiltration in amygdales, with development of chlorite- and hematite-dominated zones. In the case of jaspilites, iron mineralisation encompasses: partial replacement of jaspilitic microcrystalline hematite by blasts of martitic magnetite; jasper recrystallisation, producing fine-grained, hematite-free granoblastic quartz; martite recrystallisation, forming lobate¦subhedral hematite; pervasive porosity development by quartz-chert leaching; incipient cavity filling by microlamellar hematite; and advanced filling by coarser, euhedral and comb-textured, tabular- shaped hematite.Peak hydrothermal ore textures indicate typical epithermal-crust conditions, supported by preliminary fluid-inclusion calculations at 160 - 200¦C. Such temperatures and extreme fluid-to-rock ratios during alteration must have exceeded the ambient metamorphic conditions, with the infiltrating fluid relatively hot and capable of leaching SiO2. Therefore, mineralisation developed over exhumed, Archaean, brittly deformed rocks, with mineral associations representative of very low- to low-grade metamorphism. Considering that chlorite (¦talc) abounds in mafic rocks; hydrothermal albite is developed; dolomite fills veins and vugs; the typical rare-earth-element (REE) pattern of jaspilites is significantly modified in higher-grade hard hematite ores (higher LREE); pyrite, copper sulfide minerals and rare gold occur in association with carbonate-quartz-rich alteration zones, it is suggested that an alkaline, H2O-Fe-CO2 mineralising fluid dominated, also containing species like S¦Cu¦Au. Peak-mineralising conditions are likely to have resulted from a single, evolving fluid, via incipient- through advanced-stage alteration phases. The porous, high-grade soft hematite-type ore (SH), rich in microlamellar and anhedral hematite, must have derived from interaction with this relatively hot SiO2-leaching fluid, whereas the high-grade massive hard hematite-type ore (MH) developed due to closer fluid-rock temperature equilibrium conditions, attained by mineral reactions, with relative increase in the Fe/Σcations ratios allowing the precipitation of subhedral-tabular hematite that partially cements the soft-hematite ore. SH and MH hematite ore types must thus reflect intermediate and high fluid:rock ratios, respectively. Since the N5 deposit is to date understood to contain the largest amount of the MH ore, its units are interpreted as the loci of the highest fluid:rock ratios in the district. Preliminary mineralogical information regarding the S11 deposit of the Serra Sul (south range) implies higher-temperature conditions. The near-equant grain size and the granoblastic intergrain relationship, coupled with the presence of riebeckite, augitic pyroxene and garnet, suggest hornfels textures. The data collected, though still relatively sparse, permit the speculation that the immense driving force for the Carajßs world-class iron deposits was a relatively shallow, igneous-related hydrothermal system. If such a model is correct, then the Carajßs Palaeoproterozoic iron deposits could represent an end-member of the iron oxide-copper-gold hydrothermal system in the province.

Jan 1, 2005

By D Morrison

Backfill is usually considered a necessary evil that contributes little to the principal objective of the operation, ore production. Consequently, it is relegated to an auxiliary role in the operation with minimal equipment and resource allocation in planning and is only superficially considered during feasibility studies. In many mines, the inadequacy of the design and operation of the backfill system ultimately leads to frequent delays, excessive costs and, in the worst cases, major instabilities which result in reduced ore production and lost or unrecoverable ore reserves. The primary objective of backfill is to prevent the progressive deterioration of mined out excavations. With the exception of narrow vein operations, it is too weak to alter the mining induced stress regime and control stress concentrations caused by stope extractions. However, the direct benefits of backfill include the possibility to consider a wider range of mining methods, recovery of 100 per cent of the planned resource and the selection of a stoping sequence that minimises the regional stability problems that cause production shortfalls in the later years of mine production. Indirectly, backfill is a practical means of solving other issues, such as waste disposal, that impact the viability of mining. In Australia, the geotechnical conditions of many mines are becoming more difficult and increased attention to the importance of backfill is warranted. This paper describes realistic aspects of backfilling and the positive impacts a well co-ordinated fill system can have on mining activities as a whole. Examples are presented where an integrated approach to backfill systems have offered significant benefits to the operation.

Jan 1, 1998

By Smith C. B

Major diamond pipes discovered in Western Australia in the late-1970s exhibited a number of unique features that not only resulted in Australia becoming the largest diamond producer in the world in volume terms by 1986 but also changed geological thinking on the primary occurrence of diamond. They were: - lamproite is an alternative primary diamond host to kimberlite. - the extremely high mean grade of the Argyle lamproite pipe at 5 ct per tonne. - the tectonic setting of the lamproite pipes in mobile zones mar- ginal to the Kimberley Craton in contrast to the traditional African setting within stable cratons. Diamond was one of the earliest economic minerals discovered in Australia but 128 years elapsed between its first recognition and the first Australian economic pipe discovery (Argyle). During that period some 200,000 ct of alluvial diamonds were mined in Australia (mostly in New South Wales), but such alluvial output is insignificant on the world scene where annual production today runs at 95 million ct of natural stones some 76010 of which comes from primary pipe sources such as Argyle which alone produces 30 million ct per annum. Of particular significance therefore is the geological nature of the primary diamond source rocks in Australia. The Argyle and Ellendale Pipes are lamproites, differing from kimberlite in their mineralogy and geochemistry, and characterised by the presence of typical lamproite minerals such as leucite, priderite, potassic richterite, and the abnormally high content of chemical elements incompatible with ultramafic rocks. But not yet widely appreciated is that many other Australian olivine-rich lampro- phyres also contain diamond. Such picritic alkaline rocks can

Jan 1, 1988

By Booth S. A, Milton D. W

Stratabound/stratiform and remobilised mineralisation have been recognised as the two dominant styles of mineralisation which constitute the Broken Hill ore deposit. Recognition of prospective sites for accumulation of ore depends on understanding the heterogeneity of the ore environment and the distribution of the two styles of mineralisation. The internal stratigraphy of the Broken Hill ore deposit and its enveloping rocks, is described, and a generalised stratigraphic setting of the stratiform mineralisation is outlined. Fhiphasis is placed on the existence of closely-spaced sub-basins as potential sites for ore accumulation close to the Broken Hill ore deposit. Further from the immediate ore environment, recognition of the same diagnostic stratigraphic sequence

Jan 1, 1983

The Lane Cove Tunnel (LCT) is an important infrastructure link in New South Wales (NSW) and runs from the end of the Gore Hill Freeway at Artarmon at its eastern extremity, to the end of the M2 at North Ryde at its western extremity.  The LCT is 3.6 km long and generally consists of twin two/three lane unidirectional tunnels running largely under Epping Road from just east of Mowbray Road, west to the western end of the Gore Hill Freeway. The tunnel opened in early 2007. The presentation will provide a summary of the traffic and emission modelling performed for selected representative surface road sections in the vicinity of the Lane Cove Tunnel. An assessment of the predicted impact of vehicle emissions on ambient air quality in the corridor as a result of changed traffic conditions due to the tunnel opening will be presented. The traffic modelling and emission calculations were undertaken for the following two scenarios: Year 2006 û Lane Cove Tunnel no-build option, and Year 2006 û Lane Cove Tunnel build option. Vehicle emission calculations for the four main pollutants from vehicles: CO, VOC, NOx and PM10 on the surface roads in the vicinity of the Lane Cove Tunnel were performed using the predicted daily traffic for the two cases (no-build and build). The analyses indicated that the vehicle emissions for all pollutants are expected to significantly reduce in the corridor with the building of the Lane Cove Tunnel, including the areas in the vicinity of all tunnel portals, when compared to vehicle emissions for the no-build case.  As a result of the decreased vehicle emissions on the surface roads, the study concluded that the actual ambient air quality is expected to improve in the corridor including the tunnel portal areas after the Lane Cove Tunnel opening.

Jan 1, 2008

The Kelian gold mine which was developed in East Kalimantan Indonesia in 1990 - 1992 is scheduled to complete mining and processing operations in 2004. This will have a major impact on the neighbouring communities who have benefited from the jobs, economic activity and infrastructure development which has been generated by the mine. Currently, there are no formal regulations or standards specifying the procedures for relinquishment of mining leases in Indonesia. Furthermore, a move towards regional autonomy, providing greater authority and responsibility to local (regional) areas, has recently been implemented in Indonesia and limited capacity exists in the new regional governments. Consequently, in October 2000, Kelian Equatorial Mining (KEM) initiated a partnership with the local community and government to explore sustainable post-closure options for the mine site and community development programs. The Kelian mine closure strategy seeks full involvement of all stakeholders through the Kelian Mine Closure Steering Committee (MCSC) in the development of sustainable solutions which will enable communities to secure long-term benefits and minimise post-closure risks from the KEM operations. This organisation, jointly chaired by the Head (Bupati) of the regional West Kutai government and the KEM President Director, with representatives from the local communities, governments and NGOs, has developed a Charter, a website and evaluation criteria to ensure accountability and transparency. There are four technical working groups, consisting of representatives from the mine, local community leaders, NGOs, Universities, Local, Provincial and Central Government Departments, which report to the Steering Committee. These working groups have researched, developed and recommended sustainable options to the Steering Committee. The MCSC has met quarterly to examine options in accordance with the criteria set out in the Charter and has endorsed sustainable solutions which have support from Government, Community and the mine. This paper describes the closure risks, sustainable outcomes derived through the Kelian mine closure steering committee process and outlines the methodologies used to develop and endorse sustainable solutions in a society with limited capacity undergoing enormous change and uncertainty.

Jan 1, 2003

Gwalia Consolidated Ltd has been in the mining industry for about 15 years, yet its key wholly owned Greenbushes Mine has a history dating back to the last century. Similarly Gwalia Consolidated's associate, Sons of Gwalia Ltd owns the historic Sons of Gwalia and Marvel Loch Mines with Sons of Gwalia celebrating its centenary this year. This durability is a testament to the quality of the orebodies concerned and the massive technological achievements over this time which have enabled each of these mines to maintain their competitiveness. While Sons of Gwalia and Marvel Loch were and continue to be gold mines, the wholly owned Greenbushes Mine has survived and in fact prospered through the development of alternative products from its rich and unique pegmatite. Similarly, for Gwalia Consolidated to grow and prosper it will be necessary to expand the current portfolio of products and operations. The Greenbushes Mine has already given Gwalia world `No 1' status in both the supply of primary tantalite concentrates and lithium minerals (spodumene). The asset base contributed by Gwalia's gold investments assisted in the recapitalisation of the Greenbushes assets to fully develop their potential. Industrial minerals and strategic metals were of interest to Gwalia as these markets are relatively small and it is possible to develop an influential if not dominant position in the market with a quality asset. Capital expenditure to develop such projects are also usually in the order of $10 m to $20 m, a manageable range relative to Gwalia's size.

Jan 1, 1996

By Bush P. R, Hale M, Dixon C. J, Wheatley M. R

Barium anomalies in drainage sediments can act as indicators of barite mineralization and path- finders for lead-zinc mineralization. Their detection in an arid climate has been investigated in two areas of Saudi Arabia. At Rabigh, 150 km north of Jeddah, barium anomalies found in wadi sediments reflect barite veins which occupy Tertiary faults in Precambrian metavolcanics and granodiorite. In the Wadi ad Dawasir area, 650 km east of Jeddah, the sediments of wadis draining the Jabal Tuwayq escarpment have been found to contain anomalous concentrations of barium derived from diagenetic barite in the Sudair formation siltstones and shales. Barium dispersion in these wadis is predominantly clastic. Near to the source rocks, barium occurs in relatively coarse grains of barite. Owing to the three well-developed cleavages of barite, its crystals readily break into cleavage flakes during fluvial transport in flash floods; as a result, the longest anomalous dispersion trains are found in the 250 to 600 um fraction. Wadi sediments finer than 250 um have relatively constant and low barium contents, being dominantly composed of windblown sand.

Jan 1, 1988

By D J. Clark, R F. Wright, M D. Goodz

The A1 Gold Mine is a Devonian-age narrow vein high-grade gold deposit located 115 km east of Melbourne. The mine operated almost continuously from 1861 to 1992 producing 442 334 ounces of gold (13.8 t) from 530 436 tonnes from primary gold ore tonnes processed at an average recovered grade of 25.9 g/t Au. The A1 dyke was attributed with a yield exceeding 620 000 ounces (19.3 t) of gold (including gold in alluvial and tailings deposits), and was renowned as one of VictoriaÆs premier mines paying considerable dividends. The orebody was principally in a diorite dyke bulge 150 m long, 45 m wide and 700 m deep and was mined via two vertical shafts. The mine site was closed in 1992 and the site was rehabilitated in 1999. In 2008 - 2009, a diamond drilling program identified various extensions to the host dyke lithology and to gold-bearing quartz vein filled fault zones over a 700 m strike length. The outcome of this study was the establishment of a mine geology corridor four times longer in strike length than the original 1970s model. This opens A1 dyke hosted deposit style to exploration outside the historical dyke bulge and provides exploration opportunity for all similar deposits. Construction of the first 3D geological model has developed new insights on the host rock diorite dyke system and identified various extensions to both host stratigraphy and to gold-bearing mineralised structures. Coarse visible gold in quartz vein mineralisation (>30 g/t Au) and medium-grade stockwork mineralisation (8 - 15 g/t Au) has been intersected within 100 m of the surface and up to 300 m along strike of the nearest historical underground workings. At depth it appears that the mineralisation is continuous with the main dyke body with consideration of minor rotation in the strike orientation and limited reverse thrust faulting showing maximum displacement of 10 - 20 m. Along the A1 mine corridor, between two and five parallel dykes are observed at different drill sections. The gold mineralisation is hosted mainly within the dyke rocks, but where the sedimentary rocks are intensely silicified or are xenolith rafts, the gold mineralisation continues across these sedimentary rock blocks. There has been inference to the role of silicified sedimentary rocks as a second ore host and a bounding material for inflections in fault and vein orientations. In the central 150 m long A1 mine dyke bulge, the extremities are demarcated by four to five parallel dyke fingers (referred to as apophyses) going both north and south. These apophyses are clearly observed both vertically and horizontally between levels No 4 and No 9. The dyke fingers entrap sedimentary rock xenoliths and collectively form the A1 dyke æcorridorÆ, which is quite uniform in overall width from the easternmost contact (footwall) to the westernmost contact (hanging wall). Dyke fingers were assumed to coalesce at depth into a single dyke, but recent drilling shows this feature to repeat in several positions with depth and along strike. Key observations are the relationship between gold grade and fracture density, alteration, sulfidation, host rock morphology û relation of contact shape and fault zones. These relationships allow for the classification of prospectivity indicators and geology as a guide to potential extensions of mineralised zones. Mining geology is contributing to the whole-of-mine life planning and development where decline path, stockpile and infrastructure positions are controlled by geology.

Jan 1, 2009

In the current climate, there is a real need to bridge the gap between theory and the real world mining considerations, and develop viable, cost-effective, high performance thickeners. With a greater need to extract profits from both difficult-to-process ores and lower grade orebodies, coupled with the necessity to produce 'greener', less water intensive technologies, suppliers need to take current thickener designs to the next level and into the 21st century. The complexity of 'getting it right' within a thickenerÆs feedwell, the 'nerve centre' of the thickener, is no small task. Delivering dilution water and mixing this water with incoming feed slurry, addition of flocculant, maximising flocculant-slurry interaction to build aggregate size, minimising unabsorbed flocculant percentage, volume average of solids volume fraction, momentum dissipation ratio, dilution recycle ratio, volume average shear, maximum shear rate at exit, aggregate size on exit, uniform discharge profile and more ù all of these need to occur in the right order and in the right proportions within the feedwell. This paper discusses the genesis and evolution of a new feedwell design, the first major innovation in the thickening industry in over 15 years.

Jan 1, 2008

By D J. Alchin

Most of South AfricaÆs high-grade iron ore resources are hosted within a fault-controlled structural basin in rocks of the Palaeoproterozoic Transvaal Supergroup in the Northern Cape Province of South Africa. Iron mineralisation occurs as individual orebodies in fault-bounded basins or as fold-controlled concordant lenses around an unconformity plane above the Kuruman Banded Iron Formation. The Sishen mine near Kathu and the beeshoek mine and Sishen South deposit near Postmasburg lie on the northern and southern border of a major domal structure known as the Maremane dome, respectively. The effects and structural constraints of at least three orogenic compressive episodes and several intermittent extensional episodes on the formation, erosion and preservation of iron mineralisation on the Maremane dome and surrounding environs were investigated. Ventersdorp impactogenal rift basin development at ~2.78 - 2.64 Ga, finalised with the deposition of the volcano-sedimentary Vryburg Formation during the thermal subsidence stage at ~2.64 - 2.6 Ga, and was followed by tectonic quiescence/stability and an extensive marine transgression across the entire Kaapvaal craton. The drowning event led to the formation of a carbonate platform with the deposition of the Schmidtsdrif and Campbellrand subgroups conformably above the Vryburg Formation at ~2.6 - 2.52 Ga. The initiation of distal (to the west of the Kaapvaal craton) off-craton oceanic rifting, causing submarine volcanism and associated hydrothermal activity, led to the deposition of initially manganiferous chert (Wolhaarkop Formation) followed by banded ironstone formations (Manganore Iron/Kuruman Formation) of the Asbestos Hill Subgroup at ~2.52 - 2.46 Ga. Initial passive margin rifting along the N-S oriented western edge of the Kaapvaal craton, initiated at the end of Ghaap Group time (during Koegas Subgroup deposition) at ~2.46 - 2.35 Ga, formed a prominent system of N-S striking, westerly dipping normal faults. Easterly directed crustal compression in post-Ghaap Group time in response to the Kalahari Orogeny (accretion of Rehoboth craton along western edge (Kalahari suture zone) of the Kaapvaal craton at ~2.35 - 2.24 Ma led to the formation of large-scale regional, N-trending F1-folds. Partial to complete inversion of the Koegas passive margin rift system (ie reverse dip-slip reactivation of the N-S striking normal fault system to high-angle reverse faults and dextral strike-slip reactivation of the Ventersdorp rift system developed in the Archaean basement), was followed by uplift, erosion and formation of a regional angular unconformity (Postmasburg unconformity). Uplift was accompanied by deposition of fluvio-glacial sediments of the Makganyene Formation (Lower Postmasburg Group) within an intracratonic peripheral foreland basin setting unconformable above Ghaap Group strata at ~2.35 - 2.24 Ga. Post-orogenic crustal relaxation and rifting caused extensional reactivation of the N-trending Palaeoproterozoic passive margin rift system and NE-trending Neoarchaean Ventersdorp impactogenal rift system, forming a fault-controlled depository for the volcano-sedimentary Upper Postmasburg Group at ~2.24 - 2.1 Ga. Deceleration in rifting was succeeded by thermal subsidence of the Upper Postmasburg Group rift, erosion, formation of a regional angular unconformity and deposition of clastic sediments of the Lower Olifantshoek Supergroup unconformable above Postmasburg Group strata at ~2.1 - 1.93 Ga. Renewed rifting led to the deposition of volcano-sedimentary units of the Upper Olifantshoek Supergroup within a rift system superimposed on the Postmasburg Group rift depository at ~1.93 - 1.83 Ga. Easterly directed crustal compression during the Kheis Orogeny at ~1.83 - 1.73 Ga led to renewed inversion of rift structures of the Postmasburg Group and Olifantshoek Supergroup depository, N-trending F2 folding and thin-skinned thrusting of older rock units eastwards over the cratonic cover, thereby utilising planes of weakness in the strata such as prominent unconformities and lithological contrast boundaries as principal dTcollements. NNW-directed crustal compression in response to Lomanian (Namaqua-Natal) Orogeny at ~1.15 - 1.0 G along the southern margin of the Kaapvaal craton, resulted in minor sinistral strike-slip reactivation of the N-S striking fault system, the formation of extensional NNW-SSE striking fracture/fault zones and the development of ENE-trending F3 folds forming a F2/F3 fold interference pattern. Post-Lomanian tectonic events (eg the Pan-African Orogeny at ~650 - 500 Ma, the Cape Orogeny at ~310 - 240 Ma, and the Gondwana breakup at 205 - 120 Ma), caused only comparatively minor extensional reactivation of the pre-existing fault systems. Iron mineralisation was ultimately preserved from erosion by Kheis Orogeny-related N-trending F2 synclines and Lomanian Orogeny-related ENE-trending F3 synclines, in particular areas of interference between F2 and F3 synclines representing comparatively deep semi-circular trough- like depressions, as well as in half grabens formed adjacent to reactivated westerly dipping N-S normal faults. Support for relating the iron and manganese mineralisation to structurally controlled hydrothermal fluid flow during the Kheis orogenic event has also been found, and ongoing research is aimed at confirming and refining the hydrothermal model for iron ore mineralisation in the Northern Cape.

Jan 1, 2007

By K Rozlapa, P Waters, H Middlemis

A major challenge for closure planning at mining operations below the water table is evaporation from final void pit lakes and concentration of salts, which can impact on downstream groundwater (and surface water) flows and quality. Where such impacts are deemed unacceptable, the closure approach that is often adopted is to infill the final voids with waste rock to above the pre-mining water table to prevent the development of a pit lake and subsequent evaporative losses. BHP Billiton Iron OreÆs Marillana Creek (Yandi) mining operations face these issues. The orebody is a channel iron deposit that forms the major aquifer in the region, which will be completely mined as a series of elongated open pits over tens of kilometres. The major constraint on mine closure planning was the stripping ratio of less than one, which means that there is insufficient waste rock to infill all areas to the pre-mining water table. Hydrogeological investigations and groundwater modelling indicated that standard mine closure approaches would result in pit void lakes becoming saline sinks unless the residual void geometry was optimised to minimise evaporation and maximise throughflow. The solution developed is a cost-effective long-term mine plan that meets all mine closure objectives, and involved:the selective infilling of all pits, largely using run-of-mine waste dumping with limited re-handling; the diversion of the major part of up-catchment creek flows around the mining operations to allow mining of the resource under Marillana Creek crossings, which in turn restricted overall aquifer recharge and reduced the elevation of the long-term water table; the diversion of some minor creek tributary flows into specific locations within the mine path to induce hydraulic gradients to maintain groundwater throughflow and water quality; and close integration of mine plan optimisation (mining and waste dumping schedules) with groundwater modelling scenarios to achieve acceptable environmental outcomes. This approach is designed to result in no reduction in downstream surface water flows or quality, maintenance of adequate downstream groundwater throughflow to support groundwater dependent ecosystems, and no reduction in the beneficial use status of the downstream groundwater resource.

Jan 1, 2006

The weathering profile, in arid terrains, is commonly capped by different kinds of hardened crust, whose formation is related to recent or former climates. One may distinguish silcretes, calcretes and the ferruginous (or ferro-aluminous) laterites. the present keynote address mostly deals with the lateritic regolith and, moreover, the influence it has on mineral exploration. The lateritic regolith, also called "cuirasse", is a result of a massive accumulation of Fe (and/or Al) oxides on top of weathering profiles developed during former, probably seasonal humid, climatic episodes, and whose preservation depends on the characteristics of later climates. The total thickness of such weathering profiles commonly exceeds 50 m, with an almost complete substitution of the rock forming minerals by secondary minerals as kaolinite and Fe-Al oxi- hydroxides (hematite, goethite, boehmite, gibbsite). Such an alteration of the primary minerals assemblage is of course accompanied by significant changes of the chemical composition, as concerns major and trace elements. The latter are distributed amongst the main secondary mineral phases or trapped in some primary resistant minerals, but may also be leached, totally or partially. Gold is also affected by lateritic weathering, as shown for instance by morphoscopic and geochemical studies of gold grains collected in the different horizons of the profile, which indicates some dissolution followed by reprecipitation.

Jan 1, 1988

The first record of coal discovery in Australia dates back to 1791 when escaping convicts found coal in the banks of a creek just south of Newcastle. Development in the Newcastle Coalfield was the sole source of supply for the colony and for export until the 1850s when mines were established in the Southern & Western Coalfields. The important Hunter Coalfield was not discovered until 1873 when coal was found at Rixs Creek near Singleton: The first exploration drillholes were commenced in 1799 using drilling equipment obtained by Sir Joseph Banks. From 1820 to 1850 several famous geologists (naturalists), including the Rev W. B. Clarke, J. D. Dana and Strzelecki, wrote reports on the coal measures in New South Wales. The first Government Geo- logist, Samuel Stutchbury, was appointed in 1850. The major coal deposits of the State are contained in Permian Coal Measures in the Sydney-Gunnedah and Oaklands Basins. Coal quality ranges from high volatile, high moisture thermal coal at Oaklands to low volatile hard coking coal in the Southern Coalfield. Most coalfields can provide a range of steaming and coking coals.

Jan 1, 1988

The Douglas mineral sands deposit is located 75 km north of Hamilton in western Victoria, Australia. The deposit was discovered in the late 1990s by Basin Minerals Limited and purchased by Iluka Resources Ltd in 2002. Prestrip mining commenced in December 2004, with ore mining commencing in August 2005. Douglas is the first of several projects being implemented by Iluka Resources Ltd in the Murray Basin, with all heavy mineral concentrate planned to be treated at the companyÆs mineral separation plant in Hamilton. The mineralisation at Douglas lies along the south-eastern margin of the Murray Basin. It is hosted by marine Pliocene Loxton-Parilla Sands and consists of three discrete deposits; Bondi Main, Bondi West and Bondi East. The mineralised sediments dip at a low angle to the west and lie unconformably beneath a veneer of top soil (50 - 100 mm) and subsoil (up to 600 mm) and between three to 12 m of overburden. The barren overburden, characterised by high clay content (<53 ¦m material) generally provides a stark contrast to the sandy ore, which is between 1 m (parts of Bondi East) and 15 m (Bondi Main) thick. Both overburden and ore are removed utilising standard dry mining techniques using both scraper-bulldozer and truck-excavator combinations. All ore is delivered to run-of-mine (ROM) stockpiles before being reclaimed by front end loader into the processing plant. Grade control at Douglas is based around visual dig control aided by high precision survey, which enables accurate reference to the resource drilling and block model data. Vertical excavator faces, inclined scraper faces plus regular test pits and trenches provide opportunities for in pit mapping and sampling. This data is used to refine not only the resource estimate for Douglas but also the drilling, interpretation and resource modelling methods used for similar deposits across the basin. The foundations of the geological reconciliation process at Douglas are the in pit surveys undertaken each time the mining fleet has completed building a ROM stockpile. These surveys and the subsequent interrogation of resource models enable robust estimations of the heavy mineral content of the stockpiles, which are subsequently used to predict the daily input grades into the plant during their reclamation. Reconciliation of this daily data is then undertaken at the end of each month against metallurgical production data and plant balances. Learnings and results from the reconciliation process are used to further refine subsequent resource models and modelling methods.

Jan 1, 2009

The mostly submerged New Zealand sub-continent has a complex geological history and an active oceanographic regime that provides opportunities and challenges for offshore mineral exploration. Known deposits include polymetallic Fe-Mn nodules and crusts, polymetallic massive sulfides, phosphatic nodules, titanomagnetitie ironsands and placer gold deposits. Currently exploration interest is high with some 3.5 per cent of the EEZ under prospecting permit or application.   Article 76 of the UNCLOS convention allows coastal states to have sovereign rights over areas of the seafloor that are natural prolongations of the landmass that constitute submerged parts of the continental margin as extended continental shelf. New Zealand has substantial areas of elevated ridges and plateaux beyond the 200 M EEZ that form extended continental shelf. New Zealand has nearly completed a ten year, $44.4 M programme to define its outer extended continental shelf. New Zealand will lodge its outer limits of the extended continental shelf with the UN-appointed Commission on the Limits of the Continental Shelf in 2006, which if accepted, will enclose ~1.8 million km2 beyond the existing EEZ. Ocean Survey 20/20 is a follow-on marine mapping programme to underpin resource exploration and environmental management of the EEZ and extended continental shelf.

Jan 1, 2005

Conventional treatment of oxide and oxidised sulphide minerals by flotation involves the use of sodium sulphide for sulphidisation. Sodium sulphide is generally applied in a "slug" dosing fashion with manual regulation. However, it is recognised that "over addition" or "under addition" of sulphidising reagent can result in poor flotation recoveries. Thus, control of sodium sulphide additions is an important aspect of a sulphidisation circuit, both commercially and metallurgically. In any plant where the flotation feed is "constant" it is possible to operate at a constant rate of addition of sodium sulphide. In actual plant practice, however, it is difficult to maintain a truly constant feed for any reasonable duration because this implies not only a constant feed-rate, but also constant mineral composition and particle size range. These factors can vary significantly and ideally require corresponding variations in the additions of sodium sulphide to maintain optimum recoveries. To cope with variations in the feed, it is essential to have automatic rather than manual regulation of the sulphide reagent addition. The CPS process achieves this control by utilising a sulphide ion-selective electrode as a control instrument in sulphidisation. The CPS process which uses a selective electrode, enables the sulphide ion concentration in the flotation pulp to be monitored and controlled continuously throughout the stage of sulphidisation.

Jan 1, 1989

By J Finlay, P Betts, D Milton, H Williams

The aim of this paper is to present an innovative method to help delineate potential target volumes for haematite-goethite mineralisation as opposed to more magnetic ores. This is achieved through interpretation and modelling (2.5D and 3D inversions) of ground magnetics and gravity surveys over the Koolanooka South prospect in Western Australia. The targets are assumed to be dense and weakly magnetic and hosted within banded iron formation (BIF) horizons. Geophysical interpretation (2D map) was performed using a variety of processed magnetic and gravity images (Betts et al, 2007) to determine the distribution of lithologies, to understand the structural architecture and to map out any anomalous areas of excess density (possibly indicating goethite alteration). The created geological map is used to build geological cross-sections (geometrically consistent) that were modelled (in 2.5 D) against both potential field datasets. The crosssections are consequently used as the framework to build a 3D geological model. The model defines 3D volumes of rocks including several BIF horizons. The distribution of densities and magnetic susceptibilities of the BIFs is inverted within the GOCAD«-VPmg environment to reduce the misfit between the response of the model and the observed gravity and magnetics. By combining the results of both petrophysical property distribution it is possible to map out (using classical GIS type queries in 3D) volumes of higher density and lower magnetic susceptibility.

Jan 1, 2009

By S M. Arndt, D Tyler, F Reusch

Although significant advances have been made in understanding the mechanics of pit slopes, numerical modelling hasnÆt significantly impacted on the reliability of the design process. It is well known that legacy modelling approaches donÆt simulate large slopes well. In recent times, the emergence of very large finite element (FE) models with more than ten million degrees of freedom and the ability to simulate a large number of discrete structures, has allowed a step change in the simulation precision for slopes. The model size allows global and local effects to be realistically simulated in one model for the first time and the process can be better integrated into normal open pit slope engineering processes. Some examples of simulation of very large open pits are shown that demonstrate the challenges and some recent advances in modelling large slope behaviour. Significant limitations in the current measurement and observation regimes of open pits have been identified.

Jan 1, 2007