Search Documents

A series of in situ pull tests has been conducted to determine the holding capacity of the standard SS46 Split Set Stabilisers. The experiments have been conducted in a wide range of geological conditions ranging from bedded rock to blocky ground. The results presented in this paper indicate that cement grouted split sets bolts are likely to provide up to three times the initial bond strength per metre of embedment length provided by the ungrouted bolts. The increased load transfer capacity of the grouted bolts provides an alternative for permanent excavation support using split set stabilisers.

Jan 1, 1997

By J Weir

Accurate sampling of slurry streams is extremely important for metallurgical accounting in mining operations, not only for measuring the ore grade from the mine, but also for measuring the recovery of mineral by the mineral processing plant. Accurate sampling is also required for intermediate streams in complex circuits for determining efficiencies of processing units within the plant. As the profitability of the minerals industry is squeezed more with time, greater emphasis is being placed on efficient use of the resource and accountability of the various sections of the mining operations. This has led to increased awareness and interest in obtaining statistically correct sampling across the operations. Accurate sampling is not only required for metallurgical accounting, but is also required for on-line analysis of the slurry streams for elemental analysis and for particle size. Sampling of slurry streams for metallurgical accounting purposes has traditionally been one of the areas of concern in mineral processing plants. In the first instance, the sampler must be designed to comply with the fundamental principles of sampling theory and must provide a representative sample of the slurry stream. In the second instance, the sampler must continue to reliably provide a representative sample, regardless of wear of the equipment or build up of solids with time and other operating issues. To-date the main type of sampler that has been used in mineral processing plants for metallurgical accounting has been the Cross-Cut sampler. These have a cutter that periodically cuts across the full slurry stream. For large flow slurry streams, these are often followed by a secondary and perhaps a tertiary sampler, to reduce the flow-rate or sample, to a manageable size. This paper discusses a new method of sampling slurry streams that has been developed by Thermo Gamma-Metrics, previously known as Amdel Instrumentation. The new samplers overcome many of the problems associated with cross-cut samplers while providing a sample which is representative of the main stream, throughout the life of the sampling system. The sampler is called the SamStat (Sampling Station) and it is now proven in many applications across many countries and mineral processing plants (PGMs, Cu/Au, Pb/Zn, etc).

Jan 1, 2002

This paper discusses the prediction of subsidence over partial extraction systems in thick coal seams. A model based on empirical techniques using influence functions is developed to calculate the surface ground settlements above extraction panels. Independent of the influence function, two field parameters, the subsidence factor and the angle of draw (limit angle) are required to define the model. Both these parameters are best observed from critical or super critical subsidence areas. However in thick seams, extraction widths are typically sub critical and therefore it was necessary to refine an estimation process for sub critical conditions. Partial extraction systems in NZ are characterised by variability with respect to extraction thickness and depth. As extraction proceeds along a panel, conditions deteriorate once the critical span width is exceeded and therefore percentage extraction decreases. A further variable was introduced to the modelling which allows for varying extraction sequences. Two comparisons with field observations, one over a partial extraction panel, the other over abandoned workings, showed the method gave good agreement to measured subsidence values.

Jan 1, 2002

Improvement of Phosphate Ore Flotation Performance Through Sized Flotation

Sep 13, 2010

By R L. Brathwaite

The orogenic gold deposits wall poster is one in a series of posters on different mineral deposit types being produced by GNS Science to raise awareness of the characteristics of New Zealand mineral deposits and their prospectivity. Orogenic gold deposits are typically quartz vein deposits formed in fault and shear systems at crustal levels within and above the brittle ductile transition zone, at depths of 3 12 km and temperatures from 200¦ to 400¦C. In New Zealand, orogenic gold deposits are found in regionally metamorphosed sedimentary rocks of Paleozoic and Mesozoic age. The deposits in Paleozoic rocks include those at Golden Blocks in Northwest Nelson, Lyell and Reefton on the West Coast, and Preservation Inlet in Fiordland. Quartz veins are developed along shear zones that dip steeply and generally strike parallel to the axes of folding in the greywacke and argillite/slate host rocks, although most are discordant to bedding. The lodes are typically less than 1 m wide and extend an average 200 m horizontally and vertically, but the Birthday Reef at Blackwater, Reefton, the largest quartz vein deposit in Paleozoic rocks, averages 60 cm in width and was mined over a strike length of 1070 m, and to a depth of 830 m. Disseminated gold occurs adjacent to the quartz lodes at Globe-Progress and some other Reefton deposits. The deposits in Mesozoic rocks are hosted in schist of Otago and Marlborough, and schist and greywacke of the Southern Alps. The lodes are typically lensoidal, less than 1 m wide and localised along single or multiple parallel shear zones that generally dip steeply, and are discordant to the schist foliation and bedding. A notable exception is Macraes, where the lodes are developed in the semi-concordant, low angle Hyde Macraes Shear Zone that has a strike length greater than 25 km.

Jan 1, 2005

By R Lewis

Drill hole magnetometric resistivity (DHMMR) is a relatively recent addition to the explorationistsÆ suite of techniques for finding further resources in the vicinity of a drill hole. The method relies on gathering of an applied current into zones which are less resistive than the country rocks and it was first applied to exploration programs looking for weakly conductive sulphides, such as, for example, carbonate-hosted zinc deposits. More recently, it has been applied to a wider range of deposit styles, including highly conductive nickel sulphides. It has been found that the technique is capable of not only detecting mineralisation not seen by conventional electromagnetic (EM) techniques, but it can detect at a greater distance. Also, whilst EM is superior at defining tabular-shaped conductors, DHMMR may be more effective at finding cigar shaped sulphides. This paper presents a number of examples illustrating these findings.

Jan 1, 2000

Generating short- and long-term mine production schedules in isolation and independently from each other means that only a local optimum can be achieved when each scheduling phase is carried out. The globally optimal solution however, can be achieved when integrating scheduling phases and accounting for the interaction between short-term and long-term activities simultaneously. This paper addresses the task of integrating short- and long-term production plans by combining the short-term objective of minimising deviation to targeted mill feed grade with the long-term objective of maximising net present value (NPV) into a single mathematical model. A case study is presented which compares the present values of the same stope data set scheduled via separate long and short-term models and than by the proposed integrated model which applies a predetermined penalty for each tonne of metal deviation to target for the respective ore tonnage being processed. This allows an operation to obtain a globally optimal scheduling regime when taking into consideration the cost and loss of value resulting from fluctuations in grade to the mill over the short-term.

Dec 6, 2010

By S M. C Verryn, K Deysel

In heavy mineral sands ilmenite, rutile and zircon are present in economic concentrations. These minerals are important sources of Fe, Ti and Zr for various industrial uses. The beach sands of northern KwaZulu-Natal, along the Zululand Indian Ocean coastline in South Africa, have been mined for 30 years. The various processes involved in mining and processing these minerals have been controlled by time-consuming and labour-intensive analysis methods which, in some cases, can be replaced by X-ray powder diffraction (XRD)-Rietveld analysis. Heavy minerals are concentrated in the plant to produce a heavy mineral concentrate (HMC). The heavy mineral extraction plant is controlled and informed of the proportions of minerals in the HMC according to their magnetic susceptibility. The different fractions are called magnetic, paramagnetic and non-magnetic fractions and quality control is based on their magnetic fraction weights combined with X-ray fluorescence (XRF) elemental analysis. This current quality control process is very time consuming and labour intensive. We have aimed to show that we can, by XRD, identify and quantify all the minerals in the HMC and also in the magnetic separations. These results are then compared with results obtained by Mineral Liberation Analyser (MLA) as well as with the results from the physical separation. It was possible to detect all minerals present in the material by XRD and use the Rietveld method for a full bulk mineral quantification. A maximum of 15 minerals can be included in the Rietveld refinement due to computational restraints. Major minerals detected are rutile, ilmenite and zircon and minor minerals are quartz, epidote, anatase, amphibole, monazite, magnetite, titanite and augite. The XRD and MLA results correlate relatively well and detailed results will be presented for HMC and magnetic fraction samples. Small differences were observed for some minerals due to the different ways in which minerals are detected or due to preparation methods within each method. Rutile seems to be more abundant in the XRD analysis and the detection of Anatase is possible by XRD, but not MLA. Leucoxene (consisting of mainly microcrystalline anatase, rutile and titanite is not detectable by XRD since it is not a mineral, but ilmenite alteration phases are observed instead. There is, however, a correlation between anatase, titanite and rutile detected by XRD and leucoxene analysed by MLA.

Jan 1, 2008

By J Zhou, D M. Hunter, S M. Iveson, K P. Galvin

The REFLUX Classifier is used to perform particle separations on the basis of density utilising a set of parallel inclined channels positioned above a vertical fluidised section. In continuous mode, feed enters part way up the vertical section, while fluidisation water is introduced from below. Lower density particles are conveyed upwards and collected in an overflow stream, while high density particles segregate onto the inclined surfaces, settle to the base of the system and empty via an underflow stream. Pressure transducers are used to measure the suspension density in the vertical section. This suspension density is maintained by a pneumatically controlled underflow valve to maintain a target suspension density or ‘set point’.Previously, Galvin et al (2010) demonstrated the significant improvement achieved via a new laminar-shear separation mechanism, achieved by utilising closely spaced inclined channels in the REFLUX Classifier. For the separation of low-density coal particles from mineral matter, a channel spacing of 6 mm proved effective; however, for the separation of gangue minerals from much higher density minerals such as iron ore, the shear-induced lift needs to be even higher. In this paper, we examine the influence of two different channel widths on the continuous processing of an industrial iron ore feed in the REFLUX Classifier. It was found that when moving from 6.0 mm to 3.0 mm channels, the ability of the system to reject coarser gangue material and retain finer high density material across a particle size range from 0.125 to 1.0 mm was increased, resulting in a higher grade product.CITATION:Hunter, D M, Zhou, J, Iveson, S M and Galvin, K P, 2017. Influence of shear rate on separation of iron ore fines using the REFLUXTM Classifier, in Proceedings Iron Ore 2017, pp 205–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By D A. Manhire, R M. Flores

The commercial develop of coalbed methane from the Powder River Basin has demonstrated that low-rank coals can be a viable source of gas. Currently over 20 000 coalbed methane wells exist in the Powder River and it is predicted that there will be 50 000 wells by 2010. What makes the Powder River Basin successful is the thickness of the coal (in excess of 30m) as well as the low ash content (

Jan 1, 2002

Recovery of Pentlandite and Chalcopyrite from Tailings by Bi-Cyclone Powerful Flotation Column

Sep 13, 2010

Japan is the largest coal importer in the world, importing from Australia, China, Indonesia, Canada, Vietnam, etc. In Indonesia, most of the produced coal is extracted from open cut mines. More open cut coal mines will be developed to fill the demand for coal in Indonesia and the world. Many surveys and projects for developing new coal mines and transferring mining technology are being conducted in tropical counties such as Indonesia and Vietnam with the aid of the Japanese Government. It has, however, been pointed out that excessive and precarious development of mines in tropical areas will damage the environments around the mines including cultivated lands, and reduce the precious rainforest. This would undoubtedly exacerbate the instability of the global climate and the food crisis in the world. This paper describes the effects of flyash on the control of acid mine drainage in order to avoid potential negative impacts on the environment caused from open cut coal mines.

Dec 6, 2010

Study on the New Flow Sheet and Wastewater Recycling for Xiaoliuguo Copper-Bearing Low-Grade Scheelite Ore

Sep 13, 2010

By J Sibbel, K Goh

A key issue facing mine managers in remote locations in Australia and overseas is that of managing a fly-in, fly-out (FIFO) workforce. Current Australian research (Sibbel, in prep) indicates that FIFO employees and their families do not differ from the general population in terms of their overall mental health and the well-being of their family relationships. However, they do face unique issues/pressures associated with the lifestyle, the impacts of which are dependent on the policies and practices of the company as well as individual coping and support mechanisms. Successful management of a FIFO site and its employees therefore requires specialist knowledge and skills beyond those of a solely residential operation. The well-being of the FIFO workforce depends on both site and individual employee characteristics, and has implications for productivity and turnover, as well as safety and health. In addition, although FIFO separates individuals and their families in time and space, the interaction between work and home must be acknowledged and taken into account. Drawing on findings from recent Australian and international FIFO research (eg Annear, Poot and Kingston, 2006; Beach, Brereton and Cliff, 2003; Brereton et al, 2006; Gallegos, 2006; Keown, 2005; Parkes, Carnell and Farmer, 2005; Sibbel, 2001, 2004, in prep; Shrimpton and Storey, 1996; Storey, 2001; Watts, 2004) this paper discusses key understandings of both the positive and negative impacts of FIFO employment on employees and their families, and provides practical management strategies as an aid to the development of best practice. Individual impacts including fatigue and loneliness, as well as family issues such as communication, continually changing roles and responsibilities and the impacts of regular parent absence are key areas which can be ameliorated by appropriate management understanding and action. A flexible framework approach is presented that is suitable for a diversity of operations, including principal and contractor workforces of different sized operations.

Jan 1, 2006

By A J. Broome

Since 2003, there has been an unprecedented growth in the demand for engineering, technical and project services in the mineral industries. This demand for services became evident in Australia earlier than many other markets and has since spread globally. This growth has created significant issues for the strategic direction and planning by the service provider. Such strategic questions include:- how fast to grow, how to recruit, train and integrate new staff, what market sectors to service, the selection of targeted customer sectors and managing strategic growth with short term demands and commercial reality. These factors are discussed using in depth experiences and examples that illustrate these strategic approaches. The relevance of this new industry environment to New Zealand services will be highly discussed.

Jan 1, 2007

Bioleaching of E-Wastes

Sep 13, 2010

Mine planning includes equipment selection as a subprocess because aging equipment must be replaced to maintain or improve productivity levels. The criteria used for decision-making in mine planning and equipment selection are often inextricably linked and inherently contradictory. For example, financial wisdom demands that development, which is an expense and locks up capital, be deferred as far into the future as possible yet on the contrary technical knowledge suggests that developing well ahead of stoping is practically desirable because it generates additional geological information required to improve planning of the unmined portion of the orebody and create better operating flexibility. Consequently, mine planning professionals have to delicately balance all decision criteria when executing mine planning in order to achieve optimal mineral extraction or when selecting equipment, so that capital is optimally deployed. These two processes can therefore be characterised as belonging to the multi-criteria decision analysis (MCDA) type of problems. MCDA problems are alternatively referred to as multiple attribute decision-making (MADM) problems and belong to a broader group of problems called multi-criteria decision-making (MCDM). There is now a gradual recognition and application of MCDA techniques in the minerals industry. This paper explores the theory, current and potential application of these techniques in decision-making in the minerals industry.

Dec 6, 2010

Detachment of Particles from Bubbles in a Stirred Cell

Sep 13, 2010

Optical sensors have emerged during the telecom boom in the late 1900s, due to the availability to low-cost telecom-grade optical components. It's only after the telecom industry's fall in 2004 that optical sensors became sufficiently developed to be a viable technology for real-world applications. Geotechnical applications have long relied on electrical sensors such as thermocouples, strain, and the venerable vibrating wire to measure physical phenomena. Although these are well suited for a large variety of applications, electrical sensors cannot be used for all applications: these are vulnerable to noise, hazardous voltages and corrosion, limiting the environments in which they can be used. In addition, electrical wires can also become an issue when sensors require external excitation or are distant from the measurement system. Finally, changes in physical properties of electrical sensors and systems over time makes regular calibration a necessity - not easy to do when these are permanently mounted on structures. Optical sensing systems are non-conducting and use light to perform various measurements. There are several optical sensor technologies available, each with different strengths and weaknesses. In addition, there are different methods of interrogating optical sensors, each of which also present different strengths and weaknesses. To make matters worse, configuring the interrogation and scaling to physical units can also be challenging to the unprepared engineer. This paper will present a holistic view of optical sensing, presenting the different optical sensor technologies and interrogation techniques. Sample optical sensing systems will be revealed and top considerations for optical sensing will be presented.

Nov 25, 2010

Combined Flow Sheet for Treatment and Recycling of Municipal Solid Waste (MSW) with Complex Morphological Composition

Sep 13, 2010