Search Documents

By Gerald Edmunds

In a paper1 before this Institute in 1940, the writer reported that the surface orientation texture of zinc and cadmium differed from the texture existing within the casting, in that basal planes were parallel to the surface. He was unable to rationalize the , origin of this surface texture. It is conceivable that the surface orientation texture is influenced by the atomic force fields, which are different at the surface and within the body of metal. It was considered that a radical changc in the surface against which the metal is cast might alter the surface texture. In trial of this, zinc has been cast against a surface of molten lead, but the same result has been obtained—i.e., (001) parallel, ± 2oo, to the surface—as was obtained when it was cast against air, Transite or iron.' Into the bottom of an open cast-iron tray, 7 by 14 in. by 2 in. deep, preheated to about 275°C., about 1/4 in. of lead, then 1/2 in. of zinc was poured, and the whole was covered with an electric heater to enforce freezing from the bottom upward. After a lapse of time sufficient for the zinc but not the lead to solidify, the zinc slab was raised free of the molten lead. The bottom surface of the zinc casting was coated with a thin layer of lead. A specimen of the slab 136 in. square was metallographically polished to flatten it and remove the slight film of lead, and the orientation was determined by the method used before,' with the result stated above. Some determinations have also been made on other metals, as follows: Surface orientation determinations were made on the 3/8-in. diameter grip section of two 1/4-in. diameter aluminum-alloy die-cast tensile bars and on a 1/8 by 1/2-in. flat aluminum-alloy die-cast tensile bar. None of these three aluminum die castings exhibited any preferred orientation at the surface. A brass die casting (nominal composition: 60 Cu, 37.75 Zn, 1.00 Sn, 1.00 Pb, 0.10 Al, 0.15 Si) furnished by C. S. Smith was also examined. The surface showed a random orientation of alpha and beta. Summary A zinc casting solidified against a molten lead surface was found to have the same surface orientation texture, (001) parallel to the surface, as other zinc and cadmium castings. Aluminum and alpha-beta brass die castings were found to have random grain orientation textures at the surface. Acknowledgment The X-ray determinations were conducted by M. L. Fuller.

Jan 1, 1945

By F. M. Lewis, J. F. Meyers

This second progress report of grinding presents comments regarding ball consumption and data pertaining to the hydroscillator, which is closed circuited with the tricone mill. A study and postulate of how balls function is presented. The paper summarizes cost reduction obtained by the method of "grinding for the tail race" rather than for "mesh tons." AT the Regional meeting in Columbus, Ohio, in September 1949, the authors presented a progress report of the first year's operation with a Hardinge tricone mill in closed circuit with a Dorr hydroscillator. The present report covers our findings on this grinding circuit to January, 1950. In order to clarify our position, the authors wish to state that no invention or discovery is claimed. The Tennessee grinding circuit is simply an engineered arrangement of known equipment arranged to incorporate all of the recognized efficiency factors of comminution as they are known today. As we concluded our first report, it was not clear how effective the Tennessee mode of operation would be on harder ores. The only information we had at that time was that the Bond grindability test at 48-mesh gave 6.04 g of undersize per revolution. A later test on the same sample at 100-mesh reduced this to 2.04 g, which is definitely in the harder ore class, and which makes the reported 8.80 kw-hr per ton of —200-mesh produced a very creditable figure. Hydroscillator Operation The machine as now developed has proved dependable and easy to operate. It starts easily under full load and responds quickly to operating adjustments. The hydraulic holes in the oscillating plate do not plug when shut down under full load. Absolutely clean hydraulic water is essential. An Elliott water screen or similar device should be an essential part of the machine to keep all scale and trash of all kinds from the hydraulic compartment. The shift operators have expressed approval of the machine. In table I we show a typical screen analysis of the hydroscillator rake sand as compared to conventional classifier rake sand on our ore. We have previously reported that of the 28.7 pct reduction in power, the hydroscillator contributed 6 pct, on a —200-mesh basis. This is a conservative figure. Some of our test runs indicated that the saving was as high as 10 pct. Laboratory studies by the Dorr Co. engineers indicate that still greater efficiency is possible. Nevertheless, the 10-ft plate is overflowing 2100 tons per day at 3 to 4 pct + 65-mesh, which is a very creditable performance by

Jan 1, 1951

I. PRESIDING OFFICER. At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-presidents, shall preside. If none of these be present the meeting shall elect a Chairman. The President shall do and perform such other duties as may from time to time be assigned to him by resolution of the Board of Directors of the Institute. II. ORDER OF BUSINESS. At each business meeting of the Institute the order of business shall be as follows: 1. Reading of minutes of preceding meeting. 2. Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of proceedings and the time of adjournment shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary shall keep a record of the proceedings of all the meetings of the Institute. He shall be custodian of the corporate seal, of the minute books and of all the legal documents belonging to the Institute. He shall have charge on behalf of the Institute of all correspondence. He shall notify all Officers and Directors and all members of committees of their election and appointment; shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and shall, in calling special meetings of the Directors, specify the objects of such meetings. He shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute. The Secretary shall be custodian of all technical or scientific papers submitted to the Institute for its consideration and shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and of the distribution thereof. The Secretary shall be the custodian of all back numbers of the Transactions and other publications of the Institute. There shall be kept under his direction an account

Jan 1, 1925

I. PRESIDING OFFICER. At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, Shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-presidents, Shall preside. If none of these be present the meeting Shall elect a Chairman. The President Shall do and perform Such other duties as may from time to time be assigned to him by resolution of the Board of Directors of the Institute. IL ORDER OF BUSINESS. At each business meeting of the Institute the order of business Shall be as follows: 1. Reading of minutes of preceding meeting. 2. Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of proceedings and the time of adjournment Shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary Shall keep a record of the proceedings of all the meetings of the Institute. He Shall be custodian of the corporate Seal, of the minute books and of all the legal documents belonging to the Institute. He Shall have charge on behalf of the Institute of all correspondence. He Shall notify all Officers and Directors and all members of committees of their election and appointment; Shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and Shall, in calling Special meetings of the Directors, Specify the objects of Such meetings. He Shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute. The Secretary Shall be custodian of all technical or Scientific papers Submitted to the Institute for its consideration and Shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and. of the distribution thereof. The Secretary shall be the custodian of all back numbers of the Transactions and other publications of the Institute. There Shall be kept under his direction an account

Jan 1, 1925

By O. W. Shimer, D. C. Helms, C. E. Brown

THE early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 334 million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20° to 90° and some are on the invert in, many sharp folds and faults. PLANNING The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been maintained. Locations of stripping areas are determined as follows: 1. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness and pitch of the beds.

Jan 1, 1944

The ability of activated charcoal or carbon to adsorb complex metal ions has been recognized for many years, but it wasn't until the late 1940s and early 1950s that attempts were made to employ carbon-In-Pulp or C. I. P. processing to the recovery of gold. Early plants using the process were those at the Golden Cycle in Cripple Creek, Colorado, the Getchell Mine near Golconda, Nevada, and at the Idria Mine in Honduras. Recovery of the carbon from the pulp was done by screening or flotation, and recovery of gold from the carbon was done by burning the carbon (a very difficult task) or by sending it to a smelter. Unfortunately at the time, the price of gold was still fixed at $3-5 per ounce and labor costs were rising to the point where these mines were no longer able to operate. Consequently, C. I. P. treatment was temporarily forgotten. In the early 1970s, however, Homestake Mining Company at Lead, South Dakota, were being forced by environmental regulations to discontinue the use of mercury for amalgamation in their 7,500 ton per day plant, and at the same time were encountering high labor costs in the slime circuit of the plant, where over 2,000 tons of slimes were filtered each day in Merrill plate and frame filter presses. Shortly before that, researchers of the United States Bureau of Mines had developed the caustic -cyanide method of stripping gold from activated carbon and an electrolytic cell (now known as the Zadra cell) to recover gold from the carbon strip liquor. Homestake and the United States Bureau of Mines then jointly operated a C. I. P. pilot plant at Lead. Results were immediately favorable and a 2,400 ton per day C. I. P. plant was then built to treat the slime fraction of the Homestake ore. (See Au and Ag Cyanidation Plant Practice, Volume I, SME of AIME, 1975. Later, Homestake built a second plant at Creede, Colorado, to treat the slime fraction of the tailings from a silver-lead flotation plant. Next was Duval Corporation's 3,000 ton per day C. I. P. plant at Battle Mountain, Nevada. Both of these latter plants are described in this volume. C. I. P. operations under construction at the time of this writing are as follows: Pinson Mining Co. , Nevada Gold Freeport Gold Company, Nevada Gold Compania Minera El Indio, Chile. Silver and Gold

Jan 1, 1981

The Atlanta Mine is located in east central Nevada, in Lincoln County, 116 km (72 miles) south of Ely and 80 km (50 miles) northeast of the old mining town of Pioche. From this famous district, high-grade copper ore was mined and shipped to a smelter in Wales in the 1850s; an early day lead blast furnace was also in operation. The Standard Slag Company began operations in May 1975 on the well known Atlanta Mine, which was operated by Roy Hardy in the 1930s. The mill is currently processing 450 mtpd (500 stpd) of gold-silver bearing ore. Mining by open pit is in a brecciated zone occurring between limestone-dolomites on the foot wall and tertiary rhyolites on the hanging wall. The quartz breccia is considered among the most abrasive in the world - shovel teeth must be replaced every week. Stripping ratio is 3.9 to 1.0. Because of the hard abrasive ore, the crushing plant consists of four units: two jaw crushers in series, one Hydrocone, and one Gyradisc. Mine feed to the primary crusher is limited to 610 mm (24 in.) in size. The remaining crushers work in closed circuit with screens to produce a mill feed of 6 to 13 mm (0.25 and 0.50 in.). Hardness of the ore is demonstrated by the fact that the reversible liners of the primary jaw crusher had to be replaced in early 1978 after handling only 39,000 mt (44,000 st) at a cost of $0.095 per mt ($0.086 per st). Another example of the extreme abrasiveness of the breccia ore was the total cost per ton in 1977 for all wear parts in the comminution circuit, including screens and grinding media. This amounted to $2.84 per mt ($2.58 per st). The Atlanta grinding plant consists of three ball mills to grind the 7 mm (1 /4 in.) crushing plant product to 85 to 90% minus 150 microns (100 mesh). Feed rate to the primary Tricone mill is determined by maintaining a cyclone overflow at 28 to 38% solids, which controls the grind mentioned above. A mixture of 90 and 65 mm (3.5 and 2.5 in. ) balls are charged to this primary mill. Both the secondary mills are charged with 50 mm (2 in ) balls. Total ball consumption is 2 kg per mt (4 lb per st). All three ball mills use rubber liners. Primary mill cyclone underflows are fed to the secondary mills close circuited with the same cyclones.

Jan 1, 1981

By W. P. Blake

FORGING under the hydraulic press, which was introduced by Haswell in the year 1861, at the machine shops of the Imperial State Railway Company of Austria, has since been greatly improved, so that at the present time there are very few parts of machines which cannot be produced in this way, and at no greater cost than iron castings. The process is now used at Vienna chiefly for such parts of locomotives as cross-heads, link-bars, axle-box frames, etc., especially where the form is intricate, and there are many angles and projections. These objects weigh from 50 to 150 lb. or more, and it is claimed for them that they are not only much cheaper than ordinary forgings, but are much more regular in form and stronger. The results which Mr. Haswell has attained, after years of patient experimenting, were well shown in the Austrian Department of the Vienna Exhibition by a collection of the pressed objects in iron and steel, just as they left the moulds, with some of them cut asunder longitudinally and the surfaces etched, so as to show the internal structure or direction of the grain. Through the courtesy of Mr. Haswell and his son I saw the hydraulic presses in full operation at the works, drawing down large Bessemer ingots, cutting them up into blocks of convenient size, and forming various parts of locomotives. They have two large hydraulic presses in use; the largest, with a piston 24 inches diameter, gives 1200 tons pressure, and the second, with an 18-inch piston, gives 600 tons pressure. The pressure in the pumps is 600 atmospheres. The action is vertical ; the piston descends upon the work, and for forging ingots is armed with a hammer-like head. An ingot of No. 7 soft Bessemer steel, which was forged in my presence, weighed 2030 lbs. One end being placed upon the anvil, the piston is brought slowly down and crowded into the mass as if it were putty or dough, forcing it each way, but chiefly in the direction of the length of the ingot, this being the narrowest section of the anvil and hammer. The piston is then raised and the ingot is moved forward for a second squeeze, and so on, until the first half of the ingot has been reduced in thickness, when it is turned on edge and the operation is repeated. The ingot is then turned end for end and forged until the whole length has been re-

Jan 1, 1874

By R. H. Dourson, B. H. Sage, W. N. Lacey

The compositions of coexisting phases in the methane-propane-n-pentane system were determined at 160° and -2 20°F. throughout the two-phase region, at pressures above 500 lb. per sq. in. The experimental results permitted the calculation of gas-liquid equilibrium constants as well as the establishment of the critical behavior of this ternary system. Although many binary paraffin hydrocarbon systems have been investigated, the experimental work relating to the phase behavior of ternary paraffin hydrocarbon mixtures at elevated pressures is relatively scarce, being limited to a study of the meth-ane-propane-PL-pentane system at 100°F.l,2 However, Guter and co-workers have studied the phase behavior of the methane-ethane-ethylene system at relatively low temperatures. Information concerning the phase behavior of ternary systems is of value in predicting the behavior of the components in multicomponent systems, since the influence of pressure, temperature, and concentration may be individually ascertained. In the light of the importance of such information, the study of this ternary system was extended to higher temperatures in order to increase the field of temperature in which the data could be applied. Since all states encountered in this investigation are above the critical temperature of methane, the details of its phase behavior are not of direct significance. The properties of propane in the heterogeneous region were taken from a correlation3 based upon recently published data. The corresponding information for n-pentane was taken from experimentally measured vapor pressures and volumetric data.4 The rnethane-propane system has been studied throughout the two-phase region at temperatures above 70°F.,5 while the phase behavior of the propane-n-pentane system has been established for temperatures above 160°F.6 The volumetric and phase behavior of the methane-72-pentane system has been studied in detai1.7,8 The experimental measurements serve to establish with adequate accuracy the phase behavior of the components and of the constituent binary systems for this ternary system. It is believed that, with the exception of the measurements for the methane-propane system, the uncertainties in the earlier data relating to the pure substances and the binary mixtures are probably less than those associated with the values reported here. Method The methods and apparatus employed in this investigation have been described.137 In principle, the method involved the withdrawal of samples of the coexisting gas and liquid phases from a vessel containing a heterogeneous mixture of methane, propane and n-pentane. Provision was made so that

Jan 1, 1943

By W. N. Lacey, R. H. Dourson, B. H. Sage

The compositions of coexisting phases in the methane-propane-n-pentane system were determined at 160° and -2 20°F. throughout the two-phase region, at pressures above 500 lb. per sq. in. The experimental results permitted the calculation of gas-liquid equilibrium constants as well as the establishment of the critical behavior of this ternary system. Although many binary paraffin hydrocarbon systems have been investigated, the experimental work relating to the phase behavior of ternary paraffin hydrocarbon mixtures at elevated pressures is relatively scarce, being limited to a study of the meth-ane-propane-PL-pentane system at 100°F.l,2 However, Guter and co-workers have studied the phase behavior of the methane-ethane-ethylene system at relatively low temperatures. Information concerning the phase behavior of ternary systems is of value in predicting the behavior of the components in multicomponent systems, since the influence of pressure, temperature, and concentration may be individually ascertained. In the light of the importance of such information, the study of this ternary system was extended to higher temperatures in order to increase the field of temperature in which the data could be applied. Since all states encountered in this investigation are above the critical temperature of methane, the details of its phase behavior are not of direct significance. The properties of propane in the heterogeneous region were taken from a correlation3 based upon recently published data. The corresponding information for n-pentane was taken from experimentally measured vapor pressures and volumetric data.4 The rnethane-propane system has been studied throughout the two-phase region at temperatures above 70°F.,5 while the phase behavior of the propane-n-pentane system has been established for temperatures above 160°F.6 The volumetric and phase behavior of the methane-72-pentane system has been studied in detai1.7,8 The experimental measurements serve to establish with adequate accuracy the phase behavior of the components and of the constituent binary systems for this ternary system. It is believed that, with the exception of the measurements for the methane-propane system, the uncertainties in the earlier data relating to the pure substances and the binary mixtures are probably less than those associated with the values reported here. Method The methods and apparatus employed in this investigation have been described.137 In principle, the method involved the withdrawal of samples of the coexisting gas and liquid phases from a vessel containing a heterogeneous mixture of methane, propane and n-pentane. Provision was made so that

Jan 1, 1943

By Park Wright

The fact that granite has been encountered by the drill by those in search of oil and gas in Kansas is becoming more and more a matter of interest, not only to the oil producer but to everyone directly and indirectly connected with the oil business. It is, therefore, time that someone should offer an explanation for its presence and form a definite opinion, based on all the data available, in regard to the effect it will have on the future prospects of the area affected as probable oil-and gas-producing territory. At present there seems to be no consensus of opinion. To the writer's knowledge, only one attempt has been made to explain ; by Erasmus Haworth, State Geologist of Kansas, in a paper entitled Bulletin Number Two on Crystalline Rocks in Kansas. The purpose of the present paper is to offer a theory for the presence of the granite, and to draw conclusions which will aid in determining the prospective oil and gas value of the area in question. In taking up this question it will be well to consider first the tests in which granite has been reported, with a general history of each. The accompanying map (Fig. 1) shows the location of all wells described. The first well in which granite was reported was that drilled just south of Zeandale in section 27, township 10 south, range 9 east, by a local company which had taken up a block of leases in that vicinity. At a depth of 958 ft. (291.99 m.) granite was encountered. Drilling was continued to a depth of 1093 ft. (333 m.) in the same formation, at which depth the hole was abandoned. Another well was started 1 mile east of the first well and the same rock was found at a depth of 945 ft. (288 m.). Drilling was continued to a depth of 1200 ft. (365.76 m.) with the bit in the same formation. Samples of the drill cuttings have been examined and they are undoubtedly crushed granite. The next well in which granite was found was that drilled by DeLaat and Shepard, independent wildcat operators, in section 34, township 19 south, range 7 east, near the town of Elmdale. Granite was struck at 1707 ft. (520 m.) and the hole was abandoned in the same formation at 2525 ft. (769 m.). Mr. DeLaat watched the drilling of this well very closely and he has described to me in some detail the formation immedi-

Jan 1, 1918

By Michael B. Bever, Carl F. Floe

The solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to I300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. Review of Previous Work The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar5 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwasé3 reported large hydrogen solubility values for several compositions of copper-tin alloys, which appear to be in error.

Jan 1, 1944

By Carl F. Floe, Michael B. Bever

The solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to I300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. Review of Previous Work The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar5 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwasé3 reported large hydrogen solubility values for several compositions of copper-tin alloys, which appear to be in error.

Jan 1, 1944

By F. J. Mehringer, C. W. MacGregor

VARIOUS investigations have been carried out to determine the effects of cold-rolling on the common physical properties as represented by the yield strength, tensile strength, percentage of elongation and ordinary reduction of area. Very little information is available in the literature with reference to the effects of cold-rolling on the true stress-strain properties. Since the ordinary physical properties base both the stresses and the strains on the original dimensions of the test piece, which are greatly changed during the test, they are essentially empirical values and do not represent physically either true stresses or true strains. Consequently, they do not give an accurate picture of the effects of different conditions, both mechanical and metallurgical, on the strength and ductility of the material. It is not, however, the purpose of this paper to review the various advantages accruing from the use of true stress and true strain values, since these have been shown elsewhere,1-12 but to utilize them in representing the various effects considered. The true stress S and true strain (e = q') values mentioned above for the tension test are defined by1 [ ] where P, A, Ao are the axial load, the instantaneous area and the original area of cross section, respectively. From simultaneous readings of the axial load and the dimension or dimensions determining the instantaneous area of cross section, the true stress-strain curve is constructed by using the relations given in Eq. I. It is then the object of this paper to discuss the general effects of cold-rolling on the true stress and strain values for a low-carbon steel together with the effects of age-hardening and directionality on these properties. PRELIMINARY INVESTIGATIONS The material considered throughout the paper is a low-carbon steel of the following chemical analysis: C, 019 per cent; S, 0. 118; P, 0.092; Mn, 0.85; Si, 0.01. The stock was received in bars, 7 by 3/4 in., and was first annealed for one hour at 1650°F. followed by a furnace cool. Photomicrographs of this material showed considerable directionality even in the annealed condition. In view of the possible effects of the nonhomogeneity and directionality in this material, it was considered important to investigate their influence on the true stress-strain diagrams. In addition, the effect of strain-aging in this steel was also made the subject of a preliminary study. Elect of Aging on True Stress-strain Properties Since a certain time element would elapse between the cold-rolling operation and the final tension tests, it was determined to investigate the aging character-

Jan 1, 1945

By J. Gordon Parr, D. H. Polonis

High purity alloys of titanium and iron, made by a technique of levitation melting, have been investigated with particular reference to martensite formation and decomposition in the hypoeutectoid range. A preliminary study has been made of the occurrence of the phase corresponding to the structure Ti2Fe. MANY of the previous investigations of Fe-Ti alloys have been made using Kroll sponge as a source of titanium; and the subsequent heat treatments to which alloys have been subjected has, on occasion, led to further contamination. Worrier,',' who suggested a part of the equilibrium diagram for the binary system, and Wallbaum and coworkers,3-5 who worked largely with iron-rich alloys, all used Kroll sponge. Van Thyne, Kessler, and Hansen,6 in their determination of the equilibrium diagram, used iodide titanium for alloys up to 30 pct Fe. Duwez,7 who measured the M. temperature of titanium binary alloys with many solute elements, used iodide titanium in all cases except in his work on Ti-Fe alloys for which he used Kroll sponge. The investigation of the supposed phase Ti2Fe by Rostoker8 nvolved the use of iodide titanium. A section of the constitutional diagram, after Van Thyne et al., is reproduced in Fig. 1. Frequently too much stress is placed on the effect of contaminants in equilibrium and nonequilibrium systems, but there is no doubt that titanium alloys are extremely susceptible to interstitial atoms. Consequently, the main purpose of the work to be described was to determine those features of phase transformations in pure Ti-Fe alloys that were considered of importance in commercial heat treatments. For, although commercial alloys may not be of high purity, the investigation of a system uncomplicated by traces of impurity is a desirable starting point. Another incidental feature, the occurrence of Ti2Fe, was also investigated. The entire study was carried out using powders obtained from alloy ingots, for diffusion reactions are often more rapid in small particles than in bulk specimens. The frequently adopted practice of ascertaining phase constitutions by X-ray analysis of powders, and relating these to the microstructures and mechanical properties of bulk specimens, is considered by the authors to be open to criticism. In the martensite reactions in the Fe-Mn system, for example, it has been shown- hat similar phase distributions in solid and powder may result in different hardness values and appearance under the microscope; and it is possible that similar anomalies might occur in the Ti-Fe system. Consequently, in order to

Jan 1, 1955

By B. J. Harlan

The trying times experienced by the steel industry during the past four years have emphasized the necessity of producing pig iron at the lowest possible cost. The trend in both design and operation of blast furnaces has been toward this end rather than toward securing maximum production from a unit or group of units. In the following discussion the trend in design of stacks and auxiliary equipment will be taken up before operation is considered. Although few furnaces have been constructed in the past few years, the trend is definitely toward larger furnaces with a hearth diameter of 24 or 25 ft. Such a furnace is very flexible, being able to produce efficiently any desired daily tonnage between 500 and-1000 or more. The detail of the design of furnace stacks, with the exception of the top, has changed little in recent years. To decrease the velocity of gas through the throat of the furnaces, thereby reducing flue-dust losses, the stock-line areas are constantly being made larger. The top dimensions of the larger furnaces are usually as follows: Stock-line diameter, 19 to 20 ft.; large bell diameter, 14 to 15 ft.; straight section of throat, 5 to 10 ft. high; inwall batter, 1 to 11/4 in. Pe ft. The ratio between the area of the stock line and the area of the large. bell is usually about 1.85 to 1. The stock-line diameter of some smaller furnaces has been increased to that of the hearth diameter of the stack at the expense of the stack batter. Remarkable decreases in flue-dust production are claimed for the so-called " Venturi top," which is achieved by flaring the stock line, in the form of an inverted cone, from a diameter of 17 ft. at 10 ft. below the large bell closed to a diameter of 19 ft. 6 in. at 3 ft. below the large bell closed. Time alone will tell which of the two designs is the better. Because of differences in raw materials, one top may be better for some plants and the other top for other plants. In the search for lower costs and higher efficiencies all operators are, adopting stoves that will maintain maximum hot-blast temperatures with a minimum gas consumption. To meet these requirements, stove capacity of approximately 7 sq. ft. of heating surface and 1.8 cu. ft. of brick volume is required per cubic foot of wind blown per minute.

Jan 1, 1934

By A. Mitchell, T. Bagshaw

A recent paper by Thomas1 has presented new data on the solubility of hydrogen in solid silver at 1 atm pressure in the temperature range 600° to 963°C. However, no data is reported in the literature on hydrogen solubility in liquid silver. The Sieverts technique which has been described previously2,3 was used in the present work. Charges of approximately 160 g were melted in Morgan "purox" recrystallized alumina crucibles and purified helium was used for the determination of the "hot volume" during each experiment. A chemical analysis of the silver indicates that the impurity content (Cu + Al) is less than 0.02 wt pct. Hydrogen solubility in the temperature range 963° to 1200°C was investigated. The results of three experiments are shown in Table I. Fig. 1 shows an Arrhenius plot of the present work together with the solid-state data of Thomas, Steacie, and johnson,4 Eichenauer et al.,5 and Siegelin et al.6 The following expression has been derived from the Arrhenius plot of the present data: log (solubility of hydrogen, cm3 per 100 g) = 2.154-3512.0/ToK The heat of solution derived from Fig. 1 is 31,150 cal per g mole H2 compared with the value of 33,020 cal per g mole H2 obtained by Thomas and 12,000 cal per g mole H2 obtained from the data of Steacie. It was observed that hydrogen evolution took place when the silver melts were solidified under 1 atm of hydrogen, which would not be expected from an extrapolation of the results of Steacie. Schenck and Lange7 have observed that, for several transition metals at their melting points, the ratio of the hydrogen solubility in the liquid to that in the solid lies in the range 2.1 to 3.1. The present results and those of Thomas are in accord in this respect having a ratio of 2.8. 'C. L. Thomas: Trans. TMS-AIME, 1967 vol. 239, pp. 485-96. 2T. Bagshaw and A. Mitchell: I. Iron Steel Inst., 1966, vol. 204, p. 87. 'M. Weinstein and J. F. Elliott: Trans. TWS-AIME, 1963, vol. 227, p. 382. 'E. W. R. Steacie and F. M. G. Johnson: Proc. Roy. Soc. (London), Ser. A, 1928, vol. 117, pp. 662-79. 'W. Eichenauer et al.: Z. Metallk., 1958, vol. 49, pp. 220-25. 6W. Siegelin et al.: Z. Elektrochem., 1957, vol. 61, pp. 359-66. 'H. Schenck and K. W. Lange: Arch Eisenhuettenw., 1966, vol. 37, no. 9, pp. 739-48.

Jan 1, 1969

By Clarence Zener

The internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites, localized weak regions introduced by cold-working,6'7 grain boundaries and possibly twinning planes.8'9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3.i in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff. Experimental Method The experimental method used has previously been described in institute papers.5'6'9 The measure of internal friction adopted here, I/Q, is X the logarithmic decre- ment, a measure used by some writers, and is also X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. Experimental Results The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. I, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of 100 during the next Ioo° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e-H/RT [I]

Jan 1, 1943

By Murray F. Hawkins

Horner1 and van Everdingen8 ave shown that the pressure drop within the wellbore, as a result of having produced the well at a constant rate q for time t, where t is sufficiently large, is: van Everdingen observed that better agreement between theory and well performance can be obtained if, instead of assuming the permeability is kc everywhere about the well, it is assumed the permeability near the well-bore is substantially reduced as a result of drilling, completion and/or production practices. In order to account for the additional pressure drop he introduced the dimensionless quantity S, the skin effect factor, so that Eq. 1 becomes: Eq. 2 might have also been obtained as follows. Assume a zone of altered permeability k, exists about the well out to a radius r and beyond that the unaltered, external permeability k. The additional pressure drop required to overcome this skin of reduced permeability may be calculated with sufficient accuracy using the incompressible flow equation; for Browns-combe and Collins1 have shown almost no difference between compressible and incompressible steady-state flow, in the vicinity of the wellbore, and the small volume of fluid in the vicinity of the wellbore makes unsteady-state mechanics unnecessary. Then. The sign of this skin pressure drop will be positive or negative depending upon whether the altered permeability k, is smaller or larger, respectively, than the external permeability k... Adding the pressure drop of Eq. 3 to Eq. 1 to find the total pressure drop: Comparing Eq. 4 with Eq. 3 it is seen that the skin effect may be defined by: be determined from pressure build-up tests1,3,4,5,6,7,8 The average permeability kavg including the altered and external permeabilities, can be determined from PI tests, and may be defined approximately on the basis of steady-state flow, as was done by Thomas' in defining the damage factor, by: The productivity ratio is the ratio of the average to the external permeability, kavg/ke or This equation shows that the productivity ratio and the skin effect are not uniquely related, because of the uncertainty in the drainage radius, and also, in many instances, the wellbore radius. Fortunately, they enter in the logarithm. The curves of Fig. I are plots of Eq. 8 for values from 100 to 50,000. The points represent the skin effects and corresponding productivity ratios from a large number of well tests, taken from Fig. 15 of Ref. 5 or Fig. 13 of Ref. 9. While some of the data

Jan 1, 1957

By Ernest G. Enck

"The Rockets' Red Glare" of the Fourth of July is produced by strontium compounds. However, strontium has a number of less spectacular uses; i.e. in, or in connection with, the manufacture of ceramics, caustic soda, glass, railway and truck signal flares, beet sugar and steel. The principal ore of strontium for use both as the mineral and for production of compounds is celestite (SrSO4). This mineral varies in color from white to pink or blue depending on presence of impurities. It has a hardness of about 3.5 and specific gravity of 3.9. It is brittle and has perfect basal and prismatic cleavages. The high grade ore is obtained from England, hence it has become the standard for all other producing areas. (See analyses, Table 1.) The most objectionable impurity in English celestite is iron, coming mostly from adhering clay. On the other hand, Mexican celestite, while no higher in strontium sulfate content, is extremely low in iron (less than 0.2 pct), hence it is more desirable for certain uses. Most of the celestite in Spain and in the United States is high in calcium and barium, and commonly high in iron, and requires some form of beneficiation in order to be equal to English ore. The natural carbonate (SrCO3), or strontianite, is less important than celestite as a source of strontium, because it is less abundant and is not so widespread in its occurrence. Furthermore, it generally occurs with calcite (CaCO3) and lead sulfide (PbS), and for most uses these impurities are detrimental. This mineral is generally white or yellowish, forming needle-like crystals. It has a hardness of about 3.7 and a specific gravity of 3.68-3.8. The mineral is brittle and has an imperfect cleavage. A typical analysis of German strontianite is shown in Table 1. [ ] Distribution of Deposits UNITED STATES Occurrences of strontium minerals are known in Arkansas, Arizona, California, Illinois, Ohio, Pennsylvania, Tennessee, Texas, and Washington. Celestite occurs in the Vulture Mountains, Maricopa County, Arizona in beds three to ten feet thick associated with sandstone, gypsum, and barite. Because of the low strontium content, approximately 86 pct SrSO4, it has no commercial value. A large deposit of celestite occurs in San Bernardino County, California, in the Cady Mountains near Argus Station, about eight miles west of Ludlow. The celestite here is interbedded with shaly and clayey tuff in a zone about 300 ft thick. Massive, finely crystalline ore has been recovered with an analysis

Jan 1, 1960