Search Documents

By Byron M. Bird

JIGGING is the stratification of a mass of solid particles in upward pulsations of water or in alternating upward and downward pulsations. The stratification usually is effected in a rectangular open-top container having a perforated bottom through which the pulsations of water are applied to the materials to be separated; in separating coal, to a mass of coal and refuse. Jigging usually is a continuous process involving three steps: (1) the reception of the raw coal, (2) the stratification of the coal and refuse so that the refuse settles to the screen plate, and (3) the overflow of the cleaned coal and the withdrawal of the refuse collected on the screen. The jig is the most universal washer ever devised. It is handling in practice a wide range of closely sized coals and ores, mixed sizes of coal from 8-in. to 0 through ¾ -in. to 0, and mixed sizes of ores down to 7/32-in. to 0 and even smaller. It is treating materials ranging in specific gravity from that of gold at 19 to that of coal at 1.30. It is handling feeds in which the proportions of high-gravity materials range from 90 per cent or higher, as for some iron ores, to 10 per cent or less for some coals. It is handling feeds containing all shapes of particles-round, rectangular, and , flat. It is handling simple separation problems and difficult separation problems. Thus, it is an almost universal separating device. One might add that it has been one of the most misunderstood types of washers, from both a theoretical and a practical point of view. Although considerable progress has been made in coal jigging in the past 10 years, the jig probably has more unexplored possibilities than any other type of washer. In this chapter the object has been to treat the jigging process in a practical manner and to give information that will help the reader to improve his particular operation. Inasmuch as performance data from operating plants would contribute little of value, none has been given. Instead, the emphasis is upon jigging principles as a foundation for attacking the problems that arise. These principles are in reality tentative conclusions from research in the field of jigging during the past 10 years and most of this chapter should be regarded as a progress report on an investigation still under way. As all really difficult problems in jigging arise from an attempt to treat a large range of sizes in one operation, nearly the entire discussion will be

Jan 1, 1943

By R. F. Mehl, C. S. Barrett, A. G. Guy

INTRODUCTION IN the last few years this laboratory has published a series of papers on the mecha¬nism of age -hardening.14,1,6,11,20 Briefly stated it has been proposed that hardening is caused by lattice strains created by lat¬tice coherency between matrix and precipi¬tate; much experimental evidence has been advanced to support this thesis. The system Cu-Be is an attractive one to study. It is a system that exhibits marked age hardening; it ought to be subject to the type of analysis of structural changes hitherto explored and it is a prominent example of "discontinuous precipitation," which, though studied in other cases, 6,20 remains largely unexplained. This research shows that hardening in the Cu-Be system proceeds essentially as proposed earlier.14 Guinier-Preston zones have been observed to form on the {100) planes of the matrix; no transition lattice was found. Aging and overaging were ob¬served to occur most rapidly in the region of discontinuous precipitation-the grain boundary-apparently accelerated there by strain. The Constitution of the Cu-Be System The Cu-Be constitution diagram is shown in Fig I. The structure of the ? phase was determined by Misch16 as of the caesium-chloride type with a lattice con¬stant of 2.598 Å High temperature X ray photograms of 7.2 pct Be alloy made by Kossolapow and Trapesnikow13 led them to conclude that the structure of the P phase is simply disordered body-centered cubic with [ao] = 2.79 Å at 750°C. Previous Work The initial work on the age-hardening of Cu-Be alloys was that of Masing, Dahl, Holm, and Haase. Their numerous papers were published in book form in 1929, sub¬sequently translated.18 The effects of Be content, solution temperature, aging tem¬perature, and cold work on the hardness developed in these alloys were studied. An initial decrease in the electrical conduc¬tivity was observed when strips of a 2.5 pct Be alloy were aged at temperatures from 200 to 350°C; a wire of the same analysis failed to exhibit this decrease when aged at 350°C. A volume decrease of 0.6 pct oc¬curred during aging at 250°C. Microscopic investigations of quenched and aged alloys disclosed a regularly ori¬ented "striping" (ripples) on the a and on the ß grains. In the case of the ß the cause of the striping was held to be decomposition

Jan 1, 1948

By David R. Mitchell, Byron M. Bird

THE revision of this chapter has presented a problem in that heavy-medium jigging has come into the picture since the chapter was originally written (seven years ago), a practice in which an artificial medium is built up and maintained in the jig circuit. As this development makes the jig a "true" heavy-medium process, the method belongs in the chapter dealing with such processes. Although putting this development in its proper position in the book involves some repetition, this seems to be the best procedure, and it has been followed. As the chapter on jigs in its original form was intended to be more or less a handbook on jigging for the use of the practical man, and the great bulk of the material therein is still generally applicable, the text has been re-used in large measure. Two major changes should be noted: (1) the portion of the text relating to the refuse-withdrawing mechanism of the McNally-Pittsburg jig has been entirely rewritten, and (2) a description of the hutch valves on the Jeffrey jigs has been added. Jigging is the stratification of a mass of solid particles in upward and downward pulsations. The stratification usually is effected in a rectangular open-top container having a perforated bottom through which the pulsations of water are applied to the materials to be separated; in separating coal, to a mass of coal and refuse. Jigging usually is a continuous process involving three steps: (1) the reception of the raw coal, (2) the stratification of the coal and refuse so that the refuse settles to the screen plate, and (3) the overflow of the cleaned coal and the withdrawal of the refuse collected on the screen. The jig is the most universal washer ever devised. It is handling in practice a wide range of closely sized coals and ores, mixed sizes of coal from 8-in. to 0 through 3/4-in. to 0, and mixed sizes of ores down to 7/32-in. to 0and even smaller. It is treating materials ranging in specific gravity from that of gold at 19 to that of coal at 1.30. It is handling feeds in which the proportions of high-gravity materials range from 90 per cent or higher, as for some iron ores, to 10 per cent or less for some coals. It is handling feeds containing all shapes of particles-round, rectangular, and flat. It is handling simple separation problems and difficult separation problems.

Jan 1, 1950

By C. E. Mills

The Verde mining district is in Yavapai County, in north-central Arizona. Jerome, the principal town, has a population of 6000 and the two important mines of the district—the United Verde and the United Verde Extension—lie almost within its limits. Perched high on the southwest side of the Verde valley, at elevations of 4800 and 5500 ft. (1463 and 1676 m.) respectively, both mines have long tunnels from their lower levels through which the ore is hauled to the smelters. Clarkdale, the smelter town for the United Verde mines, lies in the Verde valley 4.1 miles (6.5 km.) distant in an air line from Jerome and at an elevation of 3560 ft. The two towns are connected by the standard-gage railroad of the Verde Tunnel and Smelter R. R., a subsidiary of the United Verde Copper Co. This road is 11 miles long and has a compensated grade of 4 per cent. At Clarkdale it connects with the Verde valley branch of the Santa Fe railroad. Clemenceau, the smelter town for the United Verde Extension mine, lies 3.5 miles (5.8 km.) in a southeasterly direction from Clarkdale, at an elevation of 3420 ft. It is connected to the Verde Valley branch of the Santa Fe railroad at Clarkdale by the Arizona Extension R. R., a subsidiary of the United Verde Extension Mining Co. The portal of the haulage tunnel, at an elevation of 3757.5 ft., is also connected with the smelter town by 4 miles of standard-gage track belonging to the same company. In the vicinity of Jerome, the great southern escarpment of the Arizona plateau forms the northeast side of the Verde valley. The general level of this escarpment, or "rim" as it is called, is about 4000 ft. above the Verde River. A corresponding elevation is reached only by the highest peaks of the Black Hills, which bound the valley to the southwest. Two lava-capped mesas, known as "Mingus" and "Woodchute mountains," form the culmination of the Black Hills. That part of the Old Black Hills mining district which lies between their crests and the Verde River is now known as the Jerome, or Verde, mining district. If the smelter towns are not included, a strip about 7 miles long by 3 miles (11 by 5 km.) wide, embraces practically all of the properties belonging to the Jerome district. T-bis strip lies parallel to and along the side of the Verde valley from First View, 2 miles northwest from Jerome, to the

Jan 1, 1925

By J. E. Pavlick, W. W. Mullins, H. W. Paxton

The growth of nitrogen-austenite during nitriding of large-gvained ferrite between 650" and 800°C has been studied as a functimz oJ time and nitrogen potential of the atmosphere for a variety of alloying elements dissolved in the ferrite. Whereas no preferential grain boundary penetration by aistenite takes place in zone-refined iron, the addition of aboit I zot pct oj' V, Ti, Cr. Si, or A1 produces significant protrusion of austenite down former 0-0 boundaries. This group of elernents also produces ragged y-0 interfaces in the a grains which advance more slozuly than those in zone-refined iron. 1 zut pct of Ni, Co, Mn, or Mo dissolved in ferrite leads to essentially smooth 7-a interfaces, which advance at rates very sinzilar to those in zone-refined iron. The reasons for this effect are not clear. Two possible limiting hypotheses, not necessarily exclusive, are discussed. One involves p.referentia1 grain bozindary diffusion of nitrogen. the other the production of a zone of ferrite, stpersatcirated with respect to nitrogen, from which austenite precipitates helerogeneozisly on the a-a gyain boundaries. In many phase transformations which occur by nu-cleation and diffusion-controlled growth, information on the parameters which control the rates of nuclea-tion and of growth is frequently not quantititative. The present work describes a continuation of efforts to obtain quantitative data on growth rates in systems where thermodynamic and kinetic factors are known independently, and thus where comparison with models of the growth process is possible. The work has been conducted on iron-base systems for two reasons. Firstly, there are several interesting transformations in this system, many of which are of practical importance. Secondly, the information on phase diagrams, activities, and diffusion coefficients is more complete in this system than in any other. These data are still inadequate to check all the effects of alloying elements, but at worst it is possible to make estimates and thus examine order-of-magni-tude agreement with proposed models. It will be necessary to do this in the present work. The problem studied was the growth of nitrogen-austenite in from the surface of large-grained columnar crystals of alloyed ferrite exposed to an NHs/Hz atmosphere. Earlier work by Grozier et al.' had suggested that growth of austenite may occur preferentially along grain boundaries of alloyed ferrite, whereas zone-refined (ZR) iron shows no such effect, Fig. 1. Growth of nitrogen-austenite into single crystals of zone-refined ferrite is planar provided sufficient nu-cleation sites for austenite are present, and is controlled by volume diffusion of nitrogen through the

Jan 1, 1967

By George H. Found

DURING recent years considerable interest has been focused on the energy-absorption characteristics of metal when it is cyclically stressed in vibration. The most familiar manifestation of this phenomenon, which is called the "damping capacity" or "internal friction" of a material, is involved in the dissipation of mechanical energy of vibration, which otherwise would build up to stress levels where the problems of noise and fatigue are involved. In addition to its engineering importance in structures, the damping behavior of metals, particularly at low stress amplitudes, has also been used as a unique metallurgical research tool with which to provide sensitive means for indicating certain structural changes within metals. Important contributions toward understanding the energy-dissipating mechanisms that are responsible for internal friction in metals have been made in the last few years. The information is not yet sufficiently extensive, however, to provide a useful metallurgical concept describing exactly how the structure affects the internal friction, or to encourage more general use of this technique among metallurgists. Three fundamental mechanisms have been proposed, as a result of recent experimental investigations, to account for the internal friction in nonferrous metals in low-stress amplitude tests. These include damping due to internal thermal currents that are created and flow in metal because of differential vibratory stress effects,1 damping due to localized inelastic stress relaxation at inhomogeneities within the metal,2,3 and damping related to plastic flow of a localized type for which an explanation has been sought in terms of the dislocation theory.4 How each of these mechanisms functions as a result of structural changes in the metal is, in general, not well understood because of insufficient experimental data for which the controlling variables have been segregated and because of uncertainties in regard to the nature of the structural changes themselves. In several investigations the effects of cold-working on the internal friction of polycrystalline brass and aluminum have been described. As reported by Köster and Rosenthal,5 and by Förster and Breitfield,6 there is an initial large increase in the damping when the metal is worked. The initial high value is not stable, but declines rapidly, at first, in a hyperbolic manner. About 100 hr, after straining, a stable value is reached of magnitude proportional to the amount of strain.7 In Fig. I is shown the relationship found by Zener and his collaborators between the internal friction due to cold-working of alpha brass and the amount of cold-working.8 Several investigators have made internal-friction measurements on worked poly-

Jan 1, 1945

By E. W. Davis

On the eastern end of the Mesabi Range, in Northern Minnesota, is a large formation of siliceous rock which contains bands and fine grains of magnetite. The magnetite comprises about 35 per cent. of the rock, the remainder being chiefly quartzite and iron silicates. The rock has a specific gravity of 3.4, a hardness of 7, and is extremely tough. This large deposit was located early in the history of the Minnesota iron-ore industry but has not been utilized because of its low percentage of iron as compared with the other Mesabi ores, and because of the difficulty and expense of any milling treatment that would concentrate the iron. An investigation, begun about 3 years ago, shows that the magnetit,e is finely disseminated throughout the entire formation and that there are bands or lenses of higher- and of lower-grade material, in which the magnetite and silicate are intimately mixed. As a result, the scheme of milling adopted must include a fine-crushing plant. As it is necessary to crush to 200 mesh in order to produce the desired grade of product, the fine crushing is one of the largest items of expense and for this reason has been given detailed study. It is the purpose of this paper to present some of the results of the work on fine crushing, as to both theory and practice. Previous to fine crushing the part of the rock that contains little or no magnetite can be discarded by magnetic concentrators after each reduction in size in the dry-crushing plant. This-makes it possible to fine-crush a minimum of rock and also establishes the feed to the ball-mill as below % in. The fine-crushing problem, then, consists simply in crushing the rock from 1/4 in. to 200 mesh at the minimum expense. Equipment of the Testing Plant In order to determine, among other things, the operating conditions of the ball-mill when working on this rock, a test mill of about 300 T. daily capacity was erected at Duluth, Minn. The fine-crushing plant contains a Hardinge 8-ft. by 22-in. (2.4-m. by 55.8-cm.) conical mill, a 6- by 27-ft. (1.8 by 8.2-m.) Dorr duplex bowl-type classifier, a 41/2-ft. (1.37-m.) standard Akins classifier, and the auxiliary machinery necessary to handle the products. Each machine is driven by an individual motor, each of which is provided with meters for measuring the power required. Over 150 tests have been made in the ball-mill, varying in

Jan 1, 1920

By C. S. Smith, E. W. Palmer

IN 1934, when Gregg and Daniloffl wrote their excellent monograph on the alloys of iron and copper, the most recent literature on the constitution of the alloys indicated a narrow single-liquid area for 20" above the liquidus with a closed liquid mis-cibility gap above this. Since that time, however, a number of investigators have confirmed the much earlier studies of Mushet2 and Stead3 who, among others in the nineteenth century, had described the true state of affairs. Liquid copper and iron are completely miscible in the absence of carbon, but small amounts of carbon cause liquid segregation. In 1934, one of the writers' mentioned evidence for the absence of liquid separation in carbon-free alloys at temperatures up to 1700°C. Two years later, Mad-docks and Claussen5 unequivocally established the absence of liquid segregation and published a revised diagram, reproduced in fig. 1. They also studied the limits of the two-liquid area in ternary alloys of iron, copper, and carbon as a function of carbon and iron content. In the same year Simpson and Bannister" and Schumacher and Souden7 described in some detail the properties of alloys containing 50 to 75 pct Cu. More recently Hodges et al.16 have developed the copper-rich alloys for use as high-strength conductors. In 1937, Iwase, Okamoto, and Ameniya8 published data on the miscibility gap in ternary alloys of iron, copper, and carbon that supported the conclusions of Maddocks and Claussen, and definitely located the two-liquid area at temperatures of 1450" and 1540°C. They also reported that additions of 1 pct Al, Ni, Pb, Sn, or Zn caused no segregation in 50 pct Cu alloys at 1540°C. The use of copper in amounts approximating 1 pct has found industrial employment to an increasing degree in both wrought and cast steels, for such steels are capable of being precipitation-hardened following normalizing, and have high yield strengths. This is summarized by Gregg and Daniloff,1 Sallitt,9 and Lorig and Adams,10 while Alexander" gives additional information on the heat treatment of copper-steel castings. Lippert12 has described Digby's two-phase steels containing copper and chromium. The work described in the present paper was done in the years 1932 to 1934, at which time much of the information was new. The excellent work subsequently done in other laboratories but more promptly published makes the present paper in part only a confirmation of what is now well known. There has not, however, been published any unified study of

Jan 1, 1951

By J. W. Spretnak, G. W. Cunningham

Grain growth across the bond region in Pressure bonded copper was found to be mainly dependent upon the presence or absence of microvoids, but it was also found that prior history, bonding pressure, bonding time, and bonding temperature are important variables. An increase in pressure, time, or temperature tends to promote grain growth in the interfacial region. Polygonization is observed after pressure bonding except for specimens previously annealed at temperatures on the order of 1800°F or higher. The dislocation density in bonded specimens was found to be greater in the bond region. THE bonding of metals by the application of gas pressure at elevated temperatures is a relatively new process, having been developed over the past 10 years. The technique, as described by Paprocki, Hodge, and Boyer,l is unique in that assemblies of many parts and complex shapes can be bonded with a negligible amount of deformation. The process thus differs metallurgically from pressure welding, cold welding, and recrystallization welding in that deformation occurs only in a microscopic region whereas, in general, the welding requires severe deformation and may extend the contact surface by a factor of 3 to 10 during the welding. From a practical standpoint, pressure welding is not amenable for bonding large surfaces. During the time in which Paprocki and coworkers were deve1oping the process, West2 established aproc-ess,for bonding aluminum to uranium, and Barnes and Maze? developed a gas-pressure-bonding technique for nickel and copper. Recently, Fugardi and Zambro4 have used equipment similar to that developed by Paprocki and coworkers to establish parameters for bonding stainless steel, aluminum, and zirconium. Most of the investigations on pressure bonding have been empirical in nature and, although methods have been developed for bonding such metals as molybdenum, columbium, titanium, zirconium, and stainless steel, the information concerning the mechanism of bonding is limited. Several workers5"7 have studied the pressure bonding of dissimilar metals in order to gain information on diffusion and formation of inter-metallic phases under application of pressure. Clapson and Robbins8 have shown by a series of annealing studies that voids in the interfacial boundary of roll-bonded copper can prevent movement of the boundary until the voids are spaced far enough apart to prevent pinning. They also indicated that recrystallization and grain growth can eliminate the voids. In this paper it is shown that voids are the major detriment to grain growth across pressure-bonded interfaces, but it is also shown that prior history, bonding pressure, bonding time, and bonding temperature are

Jan 1, 1962

By C. E. Brown, D. C. Helms, O. W. Shimer

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. . The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90 and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been . maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness

Jan 1, 1944

By W. P. Saunders, W. R. Hibbard, G. H. Eichelman

Interest in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,' has resulted in the application of similar heat treatments to other eutectoid transformations. Studies o f the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5t6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported5 as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. Preparation of Alloys The copper-silicon alloy equilibrium diagram is shown in Fig 1. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutec-toid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct) Smith6 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker's commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.' Following the casting techniques of Krynitsky, Saunders and Stern,s the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under thc melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X K in., was annealed at 750°C for 21 hr and furnace cooled, About }{& in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. and The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1949

By Walter Knox, J. D. Doherty

In 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. Summary OF Results Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3)- 2' The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages Over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 11.6 per cent to 19.2 per cent. There was a notice- able segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may be a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance ,. The, removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. with intermittent operation the burning rate was almost always less than the feeding rate, The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. 13). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). Guiding Principles In planning the investigations, the following principles were adopted: Selection of Heating Equipment.—Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By Walter Knox, J. D. Doherty

In 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. Summary OF Results Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3)- 2' The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages Over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 11.6 per cent to 19.2 per cent. There was a notice- able segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may be a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance ,. The, removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. with intermittent operation the burning rate was almost always less than the feeding rate, The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. 13). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). Guiding Principles In planning the investigations, the following principles were adopted: Selection of Heating Equipment.—Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By G. Gutzeit

An inner complex is a cyclic chemical structure containing an inorganic cation that is bound simultaneously to several atoms in a single organic molecule; on the one hand by means of ordinary valence bonds (electron exchange), on the other hand through the action of the electric field thus created, which satisfies the so-called secondary valences. The relative positions of the salt-forming and complex-forming groups are such that most frequently a four, five, or six-membered ring results through this double attachment of the cation.1-6 The formation of inner-complex ring systems depends not only upon the nature and suitable position of the salt-forming and complex-forming groups for ring closure, but, to a great extent, also on the nature of the metallic cation entering the reaction. This selective character of chelate-forming organic compounds is one of their most interesting and most valuable properties. As a matter of fact, the largest number of their practical applications is based upon their specificity.4,7-l3 Once a chelate compound is formed, its character is definitely "organic" in nature. In other words, its properties are conditioned to a much larger degree by the carbon chains or rings than by the metallic atom. Many inner complexes are soluble in nonpolar solvents such as benzene, paraffin oil or carbon tetrachloride, while the chelate-forming reagent before closure of the metal-organic ring is water soluble. (Example: copper complex of salicyl-aldoxime') It is obvious that such particular properties as those indicated above can be utilized whenever specificity and practically complete binding of inorganic ions into an undissociable complex are required. One of the well-known applications of chelate-forming compounds has been the development of specific reagents in analytical chemistry, creation of the spot-test method,4,14-16 and the application of the same principles to the contact print method for determining minerals." Chelate-forming Compounds as Collectors In the field of flotation, where selectivity is often a quality of paramount importance for the collector, various workers have lately attempted to apply their knowledge of specific organic analytical reagents to this purpose. A. C. Vivian18 has concentrated cassiterite by using ammonium nitrosophenylhydroxyl-amine (Cupferron) C6H5NO(=NONH4). Holmanl9 has tested dimethylglyoxime for the flotation of nickel oxide minerals, while deWitt has shown in a series of systematic experiments that alpha-diox-imes were generally selective collectors for nickel ores. Taurin NH2(CH2)2S03H has been proposed for the concentration Of Oxidized lead ores.19 Diphenylthio-carbazone

Jan 1, 1947

By G. Gutzeit

An inner complex is a cyclic chemical structure containing an inorganic cation that is bound simultaneously to several atoms in a single organic molecule; on the one hand by means of ordinary valence bonds (electron exchange), on the other hand through the action of the electric field thus created, which satisfies the so-called secondary valences. The relative positions of the salt-forming and complex-forming groups are such that most frequently a four, five, or six-membered ring results through this double attachment of the cation.1-6 The formation of inner-complex ring systems depends not only upon the nature and suitable position of the salt-forming and complex-forming groups for ring closure, but, to a great extent, also on the nature of the metallic cation entering the reaction. This selective character of chelate-forming organic compounds is one of their most interesting and most valuable properties. As a matter of fact, the largest number of their practical applications is based upon their specificity.4,7-l3 Once a chelate compound is formed, its character is definitely "organic" in nature. In other words, its properties are conditioned to a much larger degree by the carbon chains or rings than by the metallic atom. Many inner complexes are soluble in nonpolar solvents such as benzene, paraffin oil or carbon tetrachloride, while the chelate-forming reagent before closure of the metal-organic ring is water soluble. (Example: copper complex of salicyl-aldoxime') It is obvious that such particular properties as those indicated above can be utilized whenever specificity and practically complete binding of inorganic ions into an undissociable complex are required. One of the well-known applications of chelate-forming compounds has been the development of specific reagents in analytical chemistry, creation of the spot-test method,4,14-16 and the application of the same principles to the contact print method for determining minerals." Chelate-forming Compounds as Collectors In the field of flotation, where selectivity is often a quality of paramount importance for the collector, various workers have lately attempted to apply their knowledge of specific organic analytical reagents to this purpose. A. C. Vivian18 has concentrated cassiterite by using ammonium nitrosophenylhydroxyl-amine (Cupferron) C6H5NO(=NONH4). Holmanl9 has tested dimethylglyoxime for the flotation of nickel oxide minerals, while deWitt has shown in a series of systematic experiments that alpha-diox-imes were generally selective collectors for nickel ores. Taurin NH2(CH2)2S03H has been proposed for the concentration Of Oxidized lead ores.19 Diphenylthio-carbazone

Jan 1, 1947

By G. F. Jenkins

The word asbestos is a broad term that has been accepted and applied to a number of fibrous mineral silicates found in nature. They are incombustible and can be separated by mechanical means into fibers of various lengths and thicknesses, but differ in chemical composition and other properties. It is generally recognized that there are six varieties of asbestos; the finely fibrous form of serpentine known as chrysotile, and five minerals of the amphibole group, i.e., amosite (not fully recognized as a mineral species name but accepted in asbestos terminology), anthophyllite, crocidolite, tremolite and actinolite. (Figs 1-4.) Physical and Other Properties The structures of asbestos fibers have been studied intensely in recent years. X-ray diffraction patterns 1 to 15 have been used as a means of identification and classification. The amphibole group structures have been fairly well established while the serpentine group has been the subject of many investigations during the past six years. Low-angle X-ray scattering techniques5 have shown that the chrysotile fibrils are "hexagonally close packed" and parallel to each other, having cross-sectional diameters varying from 180Å* units to 300Å units, while the amphibole fibers are many times larger in cross section. The electron micrographs of chrysotile asbestos (Figs 1-4) have also indicated that the fibrils might be in the form of a hollow tube. This point has been the subject of considerable controversy by a number of investigators.7 to 16 Density measurements17 made on a sample of high quality Arizona fiber did not indicate that the fiber had a hollow tube structure; however, the so-called "sheet structure" of the fibril could be distorted in such a way that it gives the appearance of a hollow tube in the electron microscope. It is of interest to quote one investigator, F. L. Pundsack,17 in this connection: Although the empirical composition of chrysotile is 3MgO.2SiO2.2H20, the true unit cell[#] composition is best represented as Mg12(OH)16Si8O20. This cell has dimensions of a= 5.3Å, b = 9.2 Å, and c = 14.6 Å where the "a" direction is the fiber axis. The calculated density of this unit is 2.56 g/cc, a value in close agreement with experimentally determined density values for chrysotile. The exact manner in which the unit cells of asbestos are stacked together to build up a single fiber of chrysotile is not known, but from various

Jan 1, 1960

By Robert A. Colten, Frederick C. Hull, Robert F. Mehl

It is known that pearlite forms from austenite by a process of nucleation and growth, and that the rate of formation of pearlite may be described by a rate of nucleation and a rate of growth.l,2 The manner in which these two quantities operate to produce the observed isothermal reaction curve has been analyzed in a paper published in I939.3 Two types of process were described: (I) that in which nucleation occurs at the grain boundaries of the parent phase, with the nodules growing toward the centers of the grains, initially as hemispheres and then after impingement as roughly radial-columnar structures; and (2) that in which nucleation occurs generally, with the nodules growing to full spheres until impingement with other growing nodules restricts growth. Both cases are met in the formation of pearlite from austenite (Fig. I);2,4 the former, occurring near the knee of the S-curve, has been named "grain-boundary transformation," and the latter, occurring at temperatures near Ael, has been named "group-nodule transformation." In developing our knowledge of the factors that determine the rate of formation of pearlite from austenite, it is important1,2 to obtain data on the rate of nucleation and the rate of growth of pearlite. Such data, when obtained near the knee of the S-curve, will furnish information of use in understanding the factors that affect hardenabil-ity; when obtained at higher temperatures, such data will be useful in understanding the behavior of steels that during heat-treatment react to pearlite.2 It is the purpose of this paper to present data on the rate of nucleation and the rate of growth of pearlite in dependence upon composition, grain size, temperature, and the degree of homogeneity of the parent austenite. The studies are restricted chiefly to plain carbon commercial steels." Previous Data on Rate of nucleation and rate of Growth Data on the rate of nucleation and the rate of growth of pearlite have been published by Scheil and Lange-Weise,5 by Mirkin and Blanter,6,7 by Meh1,l and by Dorn, De Garmo and Flanigan.2, It is difficult to interpret the data, for in most cases too little information is given on austenitizing temperatures and times, the state of homogeneity of the austenite (presence or absence of carbide, etc.), austenite grain size, and mode of formation of pearlite at the temperatures given. Except for the approximations of Mehl and the work of Dorn, austenite grain size was disregarded, though it is well known

Jan 1, 1942

By Robert A. Colten, Frederick C. Hull, Robert F. Mehl

It is known that pearlite forms from austenite by a process of nucleation and growth, and that the rate of formation of pearlite may be described by a rate of nucleation and a rate of growth.l,2 The manner in which these two quantities operate to produce the observed isothermal reaction curve has been analyzed in a paper published in I939.3 Two types of process were described: (I) that in which nucleation occurs at the grain boundaries of the parent phase, with the nodules growing toward the centers of the grains, initially as hemispheres and then after impingement as roughly radial-columnar structures; and (2) that in which nucleation occurs generally, with the nodules growing to full spheres until impingement with other growing nodules restricts growth. Both cases are met in the formation of pearlite from austenite (Fig. I);2,4 the former, occurring near the knee of the S-curve, has been named "grain-boundary transformation," and the latter, occurring at temperatures near Ael, has been named "group-nodule transformation." In developing our knowledge of the factors that determine the rate of formation of pearlite from austenite, it is important1,2 to obtain data on the rate of nucleation and the rate of growth of pearlite. Such data, when obtained near the knee of the S-curve, will furnish information of use in understanding the factors that affect hardenabil-ity; when obtained at higher temperatures, such data will be useful in understanding the behavior of steels that during heat-treatment react to pearlite.2 It is the purpose of this paper to present data on the rate of nucleation and the rate of growth of pearlite in dependence upon composition, grain size, temperature, and the degree of homogeneity of the parent austenite. The studies are restricted chiefly to plain carbon commercial steels." Previous Data on Rate of nucleation and rate of Growth Data on the rate of nucleation and the rate of growth of pearlite have been published by Scheil and Lange-Weise,5 by Mirkin and Blanter,6,7 by Meh1,l and by Dorn, De Garmo and Flanigan.2, It is difficult to interpret the data, for in most cases too little information is given on austenitizing temperatures and times, the state of homogeneity of the austenite (presence or absence of carbide, etc.), austenite grain size, and mode of formation of pearlite at the temperatures given. Except for the approximations of Mehl and the work of Dorn, austenite grain size was disregarded, though it is well known

Jan 1, 1942

By Hsun Hu

Three single crystal strips of a 3 pct Si-Fe alloy with approximately (110) [001], (210) [001], and (100) [001] orientations were rolled at room temperature to 30, 50, and 70 pct reductions in thickness. Their deformation and annealing textures were studied. In most cases, the change in texture upon recrystallization and subsequent growth can be described as rotations around the <I10 > axes. A < WO > rotational relationship was also observed. The temperature dependence of recrystallization textures was discussed. WhILE considerable data have been published on the rolling and annealing textures in silicon-iron crystals, very little study has been made on the texture formation at various stages of rolling deformation, and during the process of recrystallization. Dunn&apos; in some of his early works had studied the orientation of recrystallized grains in crystals cut out from lightly rolled (10 to 20 pct reduction) large grained sheets. He found that in most cases a third-order twin relationship exists between the crystal and the recrystallized grains. This orientation relationship actually corresponds to rotations around the <110> axes. The more recent studies of Dunn &apos; and of Dunn and Koh &apos;5 on the rolling and annealing textures in various silicon-iron crystals were concerned mostly with a cold-rolling reduction of 70 pct and annealing at 980OC for recrystallization. Reductions of similar magnitude were also employed by Walter and Hibbard in rolling columnar crystal aggregates of a silicon-iron ingot. A systematic study of the effect of rolling reduction on the deforma- tion and annealing textures is still lacking. Regarding the effect of annealing temperature on the texture formation, Dunn3 has observed a change in therecrys-tallization texture by annealing a 70 pct rolled (1 10) [001] crystal first at a low temperature then atahigh temperature. But the details of texture formation during the annealing treatments were not thoroughly investigated. The present investigation was undertaken to study the texture developments at various stages of rolling deformation and of the recrystallization process, so that a better understanding on the texture formation in silicon-iron crystals may be obtained. EXPERIMENTAL PROCEDURE The three single crystals used in the present investigation were selected from the group of single crystal strips previously prepared7 from a high grade commercial Si-Fe alloy with 3 pct Si. The thickness of these single crystal strips was 0.040 in. The orientations of the three crystals as determined by the X-ray back-reflection Laue technique are shown in Table I. Each of the three crystals was rolled at room temperature along the strip direction to 30, 50, and 70

Jan 1, 1962

By Herbert H. Kellogg

RECENTLY the long-chain primary amines have been used extensively for the flotation of silicate minerals. The use of amines to float sulphide minerals has been investigated by several authors1-5,18 but most of this work has been done with the short-chain (less than six carbon atoms) primary amine compounds or the more expensive secondary, tertiary and quaternary amines. Perhaps the fact that the long-chain amines are good collectors for the common gangue minerals has led investigators to omit them from consideration as collectors for the selective flotation of metallic sulphides. The work reported in this paper was designed to investigate the use of a typical long-chain amine salt, lauryl amine hydrochloride, as a collector for the flotation of galena-sphalerite ores. The results show that lauryl amine hydrochloride (LAmHCI), when used in small amounts, is a good collector for the selective flotation of sphalerite and galena from the common gangue minerals. The differential flotation of sphalerite from galena was not accomplished but the amine flotation of sphalerite after the standard xanthate flotation of galena is possible. The experimental work reported herein is not complete enough to be able to say whether amine flotation of lead-zinc ores would prove superior to xanthate flotation, or whether the method is even applicable to a more complex ore than the one used for this work. However, the apparent reagent costs for the flotation operations described in this paper seem to be less than for xanthate flotation. This fact alone should be sufficient to encourage the millman to investigate the use of these amine reagents, especially as these reagents are available on a commercial scale at a reasonable price. This paper has as its secondary purposes to illustrate how contact-angle measurements have aided in this investigation, and to bring forward some evidence concerning the mechanism of the collecting action of primary amines. CONTACT-ANGLE TESTS The contact-angle measurements were made by the method described by del Giudice6 and used in recent work by Taggart and his collaborators.7-9 The mineral specimens for the contact-angle tests were carefully chosen, to avoid cracks and inclusions of other minerals. All specimens were mounted in "transoptic" plastic mounts and the surfaces were cleaned by polishing with levigated alumina on a cloth-covered glass polishing wheel. Distilled water was used on the lap during the polishing and at all subsequent steps in the contact-angle tests. The mounted mineral specimens were handled with glass forceps and special care was exercised to prevent exposure of the dean surface to air or any other source of contamination.

Jan 1, 1945