Search Documents

By H. M. Otte, A. L. Esquivel

A new leasl-squares method is Presented for determining lattice parameters of hexagonal or tetragonul structures. The method is adapted for use on electronic computers and involves a reiterative procedure. The correction factor employed raries linearly with the lattice parameter, a (determined from the Brag, angle). In contrast, Cohen's method and recent modifications of it use a correction factor that varies incersely as the squure of the lattice paramneter, a. While the recent modifications attempt to improve the precision of the extrapolated lattice parameter, a, (or-cu). by stressing the importance of the weighting factor. the present approach emphasizes the need for choosing the correct extrapolation function. A comparison between the present method (the Linear method) and Cohen's method indicates that the Linear method may be more appropriale in certain cases. through a priori no critertion appears to he available for making a chorce between the methods. The size of hexagonal and tetragonal crystal lattices is determined by two parameters, a, and c,. Although in principle the two lattice parameters can be determined independently from reflections for which h - k = 0 and 1 = 0, respectively, in practice this may be inconvenient (because of the angular positions at which these reflections may occur) or not easily possible (because of low intensity). Furthermore, if a high precision or accuracy is required, the limited number of reflections of this type available, particularly in the high-angle region, is not sufficient for the necessary corrections (mainly due to absorption) to be determined with accuracy. Several methods1-7,11-13 have been proposed employing all reflections, to obtain the optimum values, a. and co, either by a trial and error procedure or a least-squares fit. Of the latter method, cohen's5 is the best known one since it provides explicit expressions for the optimum a. and c,. However, Cohen's method is only strictly valid if an extrapolation function is used that varies linearly with l/a2 or lie2 (see Section 3), a requirement that does not appear to be generally appreciated. On the other hand, all the better known and more widely used A recent trial and error method was proposed by Massalski and King8,7 who computed extensive auxiliary tables of axial ratios vs the functions A = [(4/3)(h2 + hk +k2) + l2+(a/c)2] and C = A(c/a)2 used in computing a and c values from the observed Bragg angles. These values of a and c were then plotted against a function which permitted linear extrapolation. As a criteria; for the "optimum" values, Massalski and King rely upon a visual fitting of the line through points representing reflections of low 1-index points to compute the extrapolated value of ao and high 1-index reflections to obtain CO. The successive computations and graphical plotting required to reach the "optimum" value are quite lengthy and tedious even on a desk calculator and no quantitative assurance is obtained of having in fact selected the optimum value.* If the method of Massalski and King is used on an electronic computer, then their published tables become redundant and a least-squares fit becomes a natural selection for the choice of optimum values. Such an approach will be called the Linear method. For work now in progress on the effect of certain physical variables on the lattice parameters of hexagonal crystals, it has become essential to determine the confidence limits of small changes in the lattice parameters. Since extrapolation functions that varied linearly with a and c actually also appeared to vary linearly with l/a2 or l/c2 when tested against published as well as our data, a comparison of Cohen's method and the Linear method was considered desirable (Sections 3 and 4). For the latter method an electronic computer was required since a reiterative procedure to obtain the optimum ao and co values had to be employed. The purpose of this paper is to describe the principles of the Linear method, illustrate its application, and compare it with Cohen's method. 1) THE LINEAR METHOD The standard practice in obtaining the lattice parameters in the Debye-Scherrer method is to

Jan 1, 1965

By D. I. Bardos, A. M. Bardos, Paul A. Beck

The approximate effective silicon radii in ternary Laves phase alloys with transition elements and silicon were found to range between 1.16 and 1.21A, i.e., considerably smaller than the atomic radius calculated for elemental silicon. The atomic radii were found to increase with the size of the transition element atoms in the structure. It has been noted by Aronsson1 that silicon in solid solution in iron, cobalt, and nickel has an effective CN 12 atomic radius of approximately 1.20Å, a value very much smaller than the CN 12 radius of 1.34Å derived from the interatomic distances in elemental silicon.7 The unusually short metal-silicon interatomic distances in transition element monosilicides and disilicides have been also pointed out by various investigators.1 A similar tendency was observed by Nevitt in Cr3O type silicides.2 Recent work on Laves phases in ternary systems of silicon with transition elements4"8 suggested that extensive Laves phase fields may occur in such systems.8 It has been pointed out by Laves7 that the MgCu2 and MgZn2 type structures lend themselves particularly well for the determination of the effective radii of the component atoms. In these AB2 phases the B atoms are arranged in close packed straight lines, and their distances are related in a simple manner to the lattice parameters.8 The present work was undertaken in order to find out whether or not the B transition element in such AB2 Laves phases can be replaced to an appreciable extent by silicon. In cases where extensive substitution proves to be possible, the "average atomic radius for the B site" at various silicon contents was to be determined, and the effective atomic radius of silicon calculated by extrapolation to complete replacement of the B component by silicon. The following ternary systems were studied: Ti-Mn-Si, Ti-Fe-Si, V-Co-Si, V-Ni-Si, Nb-Fe-Si, Nb-Co-Si, Ta-Fe-Si, Ta-Co-Si, and Mo-Fe-Si. In all of these alloy systems, the Laves phase solid solutions were found to extend over a considerable range of silicon content. As previously reported,4"8 in the V-Co-Si, V-Ni-Si, and Mo-Fe-Si ternary systems Laves phases do occur, even though there are no corresponding binary Laves phases. In stabilizing the Laves phase, silicon acts as if it were decreasing the effective electron concentration of the alloy.8 A more detailed study of the boundaries of the Laves phases in the V-Co-Si and V-Ni-Si systems has been made and will be published elsewhere. In both cases, the elongated Laves phase fields extend parallel to the B-Si side of the composition triangle, clearly showing that silicon is substituting for cobalt, respectively, nickel over a wide range of compositions. The binary Laves phases NbCo2 and TaCo2 have the cubic MgCu2-type structure. It was found that, in both ternary systems with silicon, again the MgZn2-type hexagonal Laves phase is stabilized and that this phase extends to high-silicon contents. In each ternary system at least three Laves phase alloys of the composition A(B1_xSix)2 were used, x here denoting the fractional substitution of the B-transition element atoms by silicon. The alloys, listed in Table I, were prepared by arc melting in argon. Each specimen was water quenched after a homogenizing anneal of 3 days at 110(FC, except for the Mo-Fe-Si alloys, which were annealed at 1200°C. Metallographic examination showed that most of the homogenized alloys consisted of a single phase, although some had minor amounts of a second phase, as shown in Table I. X-ray diffraction patterns were prepared using an asymmetrical focusing camera of large resolution and Fe Ka radiation. The patterns were indexed, and the lattice parameters of the hexagonal Laves phases were determined from the available diffraction lines of highest indices: (213), (205), and (313). The lat-

Jan 1, 1963

By R. L. McCarron, G. R. Belton

The diffusivities of oxygen and sulfur in liquid iron have heen determined hy a capillary technique in which the surface concentrations of the solutes were established by means of appropriate H2/H2 and H2S/H, gas mixtures. Total diffusate and concentration profile results are shown to be in good accord, yielding for- 1560 and Supporting results at 1660°C are also presented. The conditions necessary to avoid gas transport control in this type of experiment are discussed. IN spite of their importance in understanding the kinetics and mechanisms of refining reactions, the dif-fusivities of oxygen and sulfur in liquid iron are not well established. Accordingly, as a first step in studies of rates of solute absorption from the gas phase into liquid iron, new measurements of these diffusivities have been made and are presented in this paper. The only published results for the diffusion of sulfur in pure liquid iron are those of Kawai.' He used a diffusion couple technique in which two cylindrical specimens, one containing sulfur and the other with negligible sulfur concentration, were joined together and held in a refractory capillary. After an experiment, the sample was quenched and the concentration distribution of the solute determined. Kawai recognized that significant changes in solute distribution occurred during melting and freezing and he attempted to correct the concentration profiles for these effects to give a sulfur diffusivity of 4.6 x 10-6 sq cm per sec at 1560°C. The method of correction, however, was not rigorous and the uncertainty in this result cannot be easily assessed. Koslov et a1.2 have reported the diffusivity of oxygen in iron as 7.8 x 10"3 sq cm per sec at 1660°C. This value appears to be unreasonably high but, unfortunately, details of their experiments are not available. Shurygin and Kryuk have used the rotating disc method for a study of oxygen diffusion in liquid iron. In their experiments a silica disc was rotated in liquid iron containing oxygen, and the rate of formation of liquid iron silicate was determined by measuring the decrease in weight of the disc. On the assumption that the rate of dissolution was controlled by the diffusion of oxygen in the iron, the diffusion coefficient was computed to be 5.2 x sq cm per sec at 1550°C. However, the Levich equation, which was used to interpret the rate data, was originally de- rived for the case of mass transfer between a solid disc and a single-phase liquid. The hydrodynamic and diffusion boundary layers in the iron stirred by a disc, via coupling of the silicate melt, may be appreciably different from those predicted by Levich's equations. Recently, Novokhatskiy and Ershov, using an identical experimental method to that of Shurygin and Kryuk, obtained a diffusivity for oxygen in liquid iron of 1.22 x 104 sq cm per sec at 1550°C: no reasons were offered for the disagreement. Schwerdtfeger5 has also recently studied the diffusivity of oxygen in liquid iron. He reacted shallow melts of liquid iron, 0.5 to 1.0 cm deep and contained in high-purity alumina crucibles, with appropriate H20-HZ-He mixtures. The total sample was analyzed, without sectioning, to obtain the average concentration of diffusate. A value at 1610°C of D = 12(3) x 10-5 sq cm per sec was obtained from the results of twenty experiments.= Oxygen profile measurements, which were carried out in three additional experiments using long capillaries and the semiinfinite boundary conditions, indicated a diffusivity about half that computed from the shallow bath experiments. Possible sources of error in Schwerdtfeger's study will be discussed later in this paper. EXPERIMENTAL TECHNIQUE The essential arrangement of the diffusion cell is shown in Fig. 1. The liquid iron was contained in an alumina capillary, 3 to 4 mm diam and 3 to 9 cm long, which was supported by a hollow alumina pedestal and this whole assembly was held within a movable alumina reaction tube. This tube, which was about 7 mm in bore

Jan 1, 1970

By Nicholas J. Grant, Michio Yamazaki

Cast copper alloys containing 10, 20, and 30 pct Ni and 0.75 to 0.80 pct Al were machine-milled into chips, then comminuted in a rod mill to fine flake powder utilizing a number of processing variables. The powders here internally oxidized, mostly at 800°C, in a low-pressure oxygen atmosphere. The consolidated powders were hot-extruded into bar stock. Room-tenmperature tension tests, stress-rupture tests mostly at 650°C, but also at 450° and 850°C, and hardness measurements after various annealing temperature treatments to study alloy stability were perfomted. Excellent room-temperature strength, high rupture strength at 650°C, and resistance to recrystallization at 1050°C were obtained. Problems in optimizing conditions for internal oxidation of Cu-Ni base alloys are discussed. THE interesting high-temperature properties of SAP' have stimulated considerable effort in the study of more refractory alloy systems where the potential for high-strength alloys at high temperature is great.2-13 A number of methods have been utilized to produce the desired fine, hard particle dispersions, of which internal oxidation2,9,7 of dilute solid-solution systems offers considerable promise by virtue of the potential for producing ultrafine, well-dispersed oxides. While most of the published works are concerned with pure metal matrices, a number of investigators have studied the effects of solid-solution strengthening.10,19 Use of more complex alloy matrices (for example, aging systems) has been unsuccessful because overaging still occurs at high temperatures in the oxide-containing alloys.14.15 Solid-solution strengthening is, however, effective at very high temperatures9,10 and might be expected to contribute importantly to the strength of oxide-dispersion strengthened alloys. For this study, internal oxidation of solid-solution alloys of copper and nickel, containing small amounts of aluminum, was chosen as the method of alloy preparation. PREPARATION OF ALLOYS Three copper alloys containing about 10, 20, and 30 pct Ni and each containing 0.75 to 0.80 pct A1 (enough to yield about 3.5 vol pct alumina) were prepared as air-cast ingots measuring 2.5 in. diameter by 6 in. high (see Table I for the analyses). Processing steps for all the alloys were as follows (also see Table 11): 1) Homogenization of the ingot at 982°C (1800°F) for 45 hr in an argon atmosphere. 2) Machine milling of ingots into fine chips. Average thickness was about 0.1 to 0.2 mm. 3) Hydrogen reduction of chips at 593°C (1100° F) for 1 hr to reduce copper and nickel oxides. 4) Rod milling of chips to finer powders. 5) Hydrogen treatment of powders as in step 3. 6) Internal oxidation of the powders. 7) Hydrogen treatment of oxidized powders as in step 3. 8) Hydrostatic compression of evacuated powders. 9) Sintering of compacts in hydrogen. 10) Hot extrusion. Variations in processing among the alloys were made in steps 4, 5, and 10 (see Table 11). In the past, two methods were utilized to internally oxidize alloy powders. Preston and Grant3 surface-oxidized dilute Cu-Al powders to obtain the necessary amount of oxygen to oxidize the solute metal (aluminum and silicon), and then permitted the formed copper oxide to diffuse and react with the solute in an argon atmosphere. Bonis and Grant4 exposed Ni-A1 and other nickel alloys to an oxygen pressure derived from the decomposition of nickel oxide at a preselected temperature, in an argon atmosphere. Both methods are applicable and can be modified to generate a range of oxygen pressures for oxidation of the solute but not the solvent metals. Procedure I: Surface Oxidation of Alloy A3, Cu-10Ni-0.76A1. Powders of -20 to +28 mesh were surface-oxidized at 500°C (932°F) to obtain the desired amount of oxygen for oxidation of the aluminum to alumina; the powder was then sealed in Vycor and heated at 900°C (1652°F) for various times up to

Jan 1, 1965

By G. Purcell, S. C. Sun

In an attempt to determine the relative collecting ability of 18-carbon fatty acids, studies were performed on rutile in aqueous solutions of the fatty acid soaps. The preceding article reported the electro-kinetic properties; this article outlines the flotation behavior. Results of these flotation experiments are described and correlated with the electrokinetic results. Recent studies of the electrokinetic1-4 and the electrochemical5,6 properties of a few solid-liquid interfaces have provided a better understanding of the flotation process. A number of investigators have attempted to determine the relative collecting ability of 18-carbon fatty acids, but their published results (even for the same mineral) vary widely. Such lack of agreement indicated a need for further investigation. In an effort, therefore, to resolve the problem, electro-kinetic studies were made on rutile in aqueous solutions of the fatty acid soaps. Following the determination of the electrokinetic properties, the flotation behavior of rutile was studied. Results of these flotation experiments are described in this paper and are correlated with the electrokinetic results. MATERIALS AND EXPERIMENTAL PROCEDURE Materials: Pure -28, + 35-mesh rutile crystals were used for all flotation tests, and nitrogen-saturated conductivity water was used throughout. Sodium hydroxide and hydrochloric acid were added for pH regulation. The methods of purification for these materials and the preparation of the soaps have been described elsewhere. 7 Equipment: A Hallimond cell, constructed in a manner similar to that described by Fuerstenau, Metzger and Seele,8 was used for the flotation of mineral particles; however, a coarse pyrex frit was substituted for the capillary. Procedure: Purified nitrogen was led through a two- way stopcock into a graduated cylinder partly filled with water. The gas forced water from the cylinder back into a header tank until the water level in the cylinder coincided with a predetermined mark. Reversal of the stopcock then allowed water in the tank to force nitrogen into the cell until the water in the graduated cylinder rose to a second predetermined mark. In this way a constant volume of nitrogen under practically constant pressure was used for each flotation test. However, the flotation time varied, depending upon the amount of mineral floated and the pH of the solution. Rutile crystals were transferred under water from a storage bottle by a glass scoop holding 1.7 g. Consistency of the scoop samples was good, varying from a low value of 1.67 to a high of 1.74 g. The water added to the conditioning bottle during mineral transfer was drained off, and then 2 cu cm of either hydrochloric acid or sodium hydroxide were added. The concentration of pH regulator was adjusted to give approximately the final soap solution pH that was required. The order of addition of reagents did not affect the results within the limits of experimental error. Soap solution of the required concentration was added under nitrogen pressure to fill the bottles completely. Conditioning for 1 hr was carried out on rolls rotating at 35 rpm. After conditioning, 2.5 cu cm of solution were run off into the container of a Beckman (model G) glass electrode pH meter. The electrodes were rinsed in this solution, which was then discarded, and 2.5 cu cm more were added for pH determination. The remaining solution and the mineral were transferred to the cell; care was taken to ensure that all mineral was washed out of the bottle by the conditioning solution. With the cell back in its flotation position the liquid just reached the desired level, and the test was started immediately. The amount of agitation in the cell was kept constant, and flotation was carried out without the use of a frother. In each series of ten tests one was run with no collector added to ensure that the mineral had not become contaminated, and two were conditioned at the same pH to check reproducibility. After each test the cell was dismounted, soaked in cleaning solution, washed in hot water and then rinsed with distilled water.

Jan 1, 1963

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.' ' The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By J. H. Waxweiler, L. C. Ikenberry, R. J. Bendure

Carbon which is present as insoluble carbides in austenitic stainless steels can be measured quantitatively by dissolving the steel in iodine-methanol and analyzing the residue for carbon. Severe sen-sitization was observed in Type 302 due to precipitation of only 0.003 pet carbon. Both cold work and the presence of delta ferrite caused a marked acceleration in rate of carbide precipitation. Carbide precipitation rates in 17-7 PH were stzulied for the austenite conditioning and also the aging heat treatment. CARBON and its compounds exercise a major influence on the properties of stainless steels and their response to thermal treatment. Sensitization in 18-8 type stainless steels has been the subject of numerous investigations throughout the years. Bain, Aborn, and utherford," and Binder, Brown, Frankss all studied the effects of heating austenitic stainless steels in the temperature range of 1000° to 1500°F. The primary purpose of most of these studies was the investigation of susceptibility to in-tergranular attack in acids due to these sensitizing heat treatments. Intergranular precipitation of carbides was always associated with intergranular attack but it was recognized2 that severe attack could occur with but minute quantities of precipitated carbide. Mahla and ielsen utilized the electron microscope to make a significant contribution in illustrating the appearance and method of growth of chromium carbides during sensitizing heat treatments. However, as they stated, their studies of residues could not be used to obtain a quantitative measurement of the amount of carbon which was actually precipitated. The aim of the present investigation was to devise a relatively fast, simple method for the quantitative measurement of carbides in stainless steel. EXPERIMENTAL WORK The initial investigations were made to determine the best means of separating carbides from the matrix. A number of dissolving media were tried using both chemical and electrolytic attack. Qualitative examination of the extracted residues by X-ray diffraction indicated that solution in iodine-methanol would furnish a good means of separation. Consequently, further work was pursued along this line. The method is quite simple. The sample in the form of millings or nibblings is dissolved in iodine-methanol solution at room temperature (6-g iodine, 25-ml methanol per g of sample). The insoluble residue containing the carbides is separated by suction filtration through an ultra-fine glass filter disc. This is a very fine filter medium that will retain particles as small as 0.1 to 0.2 p in diameter. After washing with methanol and drying, the filter disc and residue are placed in a conventional combustion carbon-tube furnace and the carbon determined gravimetrically. Using this technique it was found that reproducible insoluble carbon values were obtained. However, since such small amounts of insoluble carbon were obtained on Type 302 after sensitizatipn at 1250°F and 1500°F, the values were confirmed by a second method. In the second method the sample was dissolved with copper potassium chloride and filtered through a millipore paper. This treatment dissolves the matrix but leaves undissolved practically all of the carbon irrespective of how it is present in the steel. The amount of insoluble carbon present as chromium carbide is determined by calculation from the analysis of the residue for chromium and iron. The derivation of the formula used for this calculation is discussed later. The values obtained by the indirect copper-potassium-chloride method were in agreement with those obtained by the iodine-methano1 method. See Table I. It should be pointed out that the sensitivity of the direct combustion method is not too high when the amount of carbide present is small. This is due primarily to inherent blanks and to analytical errors such as weighing. For this reason it cannot be stated with any degree of certainty that there is a significant difference between values of 0.002 and 0.005 pct. Having confirmed that the iodine-methanol extraction gave a quantitative measurement of the precipitated carbides in Type 302, exploratory tests were conducted on Armco 17-7 PH stainless steel. Samples from commercial Heat 54807 were solution annealed at 2000°F, water quenched and heated at 1250" and 1500°F, and water quenched. The analysis of Heat 54808 is as follows:

Jan 1, 1962

By S. Shapiro, J. A. Ford

The crystallo graphy of several grains of the lamellar Ni-Ni3 B eutectic solidified under conditions appvoachirt equilibriun has been examined.. A preferred interlace relationship has been observed in this system which may be described as: A detailed study of this interface by means of an atomistic model reveals the interface Plane to be puckered and more accurately describable as: Analysis of the atomic configuration on these planes reveals that this interface conforms to the orientation criteria proposed for directionally solidified lanzellar eutectics. In addition, a model is proposed to help explain the growth of a "puckered" interface. DURING the past several years an increasing number of unidirectional solidification experiments on eutectic alloys have been reported in the literature. The primary emphasis, in most cases, has been the effect of growth variables on microstructure. Some authors have, however, studied the crystallographic orientations and interfacial relationships resulting from these experiments. Four crystallographic studies have been published;'-4 in each of these there is a factor which tends to prohibit the extension of the observations beyond the particular system. In the Al-CuA12 system, the approximately equal volume fractions of the phases have resulted in sorrie controversy as to which phase constitutes the matrix. In the Mg-Mg,Sn eutectic the presence of several interconnecting lamellar systems2 complicates the analysis. The two remaining eutectics. 1nSb-b and Al-Ali, are both rodlike (the latter exhibits a plate morphology at low solidification rates): the matrix in each of these alloys is the simpler (fcc) phase. Studies of nucleation in eutectic alloys indicate that the more complex constituent is the nucleating -.phase.' For the purpose of an analysis of interface crystallography it was deemed desirable to study a lamellar system in which the matrix was the more complex and, presumably. the nucleating phase. Recently it has been shown that there is a eutectic in the Ni-B system between Ni3B and i; preliminary investigation by the authors indicated that the matrix in this eutectic is the boride phase. The structure of Ni,B is reported to be orthorhombic, the compound being isostructural with cementite. This eutectic is therefore analogous to that between austenite and cementite. Furthermore, the Ni-B system is not susceptible to a competing eutectic reaction as occurs in the Fe-C alloys; nor does it exhibit a eutectoid decomposition. For these reasons the study of the interfacial relationship in the Ni-Ni3B eutectic was undertaken. PROCEDURE Ingots of nominal composition 3.5 and 3.6 wt pct B were induction-melted in boron nitride crucibles within a graphite susceptor under a boric oxide slag; a dynamic argon atmosphere was maintained over the melt to prevent rapid oxidation of the susceptor. The raw materials used were 99.97 pct Ni from Huntington Metals Division of International Nickel Co. and 99.8+ pct B chips supplied by the United Mineral and Chemical Co. The analyses of the starting materials are listed in Table I. The melt was held at 1500cC for 2 hr to insure complete reaction and allowed to cool to room temperature. The castings were chemically analyzed for boron and were metallographically examined for uniformity. The metallographic samples were mechanically polished through 0.1 p A1,0, and etched with Carapella's reagent. Each master casting was cut up to make several specimen blanks which were remelted, in boron nitride crucibles, to form ingots of 1/2 to 3/4 in. in diarn by 7 in. long. These ingots were unidirectionally solidified using a modified vertical Bridgman technique. The rate of solidification was assumed to be equal to the uniform rate at which the crucible-susceptor assembly was withdrawn from the induction coil. This rate was varied from 1.18 to 2.21 cm per hr. In order to perform these experiments it was found necessary to redetermine the eutectic composition. This was accomplished by the zone-melting technique described by Yue and lark.' An ingot of 4.5 wt pct B was zone-melted in a horizontal boron nitride boat 7-1/2 in. long with a 112-in.-square cross section. A

Jan 1, 1967

By J. B. Cohen, O. F. Kimball

Aging of specimens of Au-20 at. pct Ni and Au-40 at. pct Ni has been followed with electron microscopy, resistance, magnetic measurements, and X-ray diffraction. The periodic structures observed by electron microscopy in Au-Ni alloys by Fisher and Embury are shown to be due to nickel-rich prepre-cipitates. Assuming this alloy system undergoes spinodal decomposition, our observations and available data on thermodynamic properties and elastic constants indicate that the gradient energy coefficient in this system is of the order of 10-5 ergs cm-1 . Shifts of X-ray peaks in this system have been found to be due primarily to residual stresses, not faulting. A large effect of applied stress during aging was detected by X-rays and electron microscopy for the Au-20 at. pct Ni alloy. The presence of a preprecipitation stage during aging of gold-rich Au-Ni alloys for short times below 300°C has been indicated by several previous investigations. Changes in electrical resistivity,1"3 elastic modulus,4 superparamagnetisrn,5 positions of X-ray diffraction peaks,6 and hardness7 have been studied. Electron diffraction and microscopic studies by Fukano8 and Fisher and Embury9 respectively showed that the precipitation process resulted in the formation of periodic composition fluctuations—perhaps spinodal decomposition. MOSS10 detected a satellite with X-rays in quenched specimens, but the wavelength was much smallerthan that found by Fukano. Recently Woodilla and Averbac11 detected a modulation similar to that found by Moss, but with electron diffraction. They suggested that the microstructures observed by Fisher and Embury may be simply due to a Moir'e effect from a back deposit of gold during electropolishing. Satellites in electron diffraction can be enhanced by small bends or tilts of a foil. Even if this were not the case, asymmetric satellites, as are found in Au-Ni are difficult to analyze. They are principally influenced by the large differences in atomic size in this system, and obtaining information on the associated composition fluctuations depends on assumptions as to whether or not there are isolated clusters or composition "waves", and in the latter case whether or not the entire specimen has decomposed. Assuming that decomposition was complete in alloys aged at low temperatures, Woodilla and Averbach suggested that the satellites indicated a composition which varied about the average value by only± 5 pct, much less than that predicted from the phase limits, Fig. 1; they attributed this small variation to a cessation of the reaction caused by the loss of mobile vacancies. In Ref. 12 it was shown that vacancies are trapped by the preprecipitate in this system. Furthermore, after reversion, aging proceeds at a much slower rate than immediately after a quench from the solution temperature,5'11,13 indicating the importance of vacancies in the kinetics. In some senses Au-Ni is a favorable system for studying preprecipitation and reversion mechanisms because of the simplicity of the equilibrium diagram14 and the availability of good thermodynamic15 and diffusion data.16,l7 The calculations necessary to relate the decomposition process to classical nucleation and growth or to spinodal decomposition, as well as those necessary for understanding reversion mechanisms, can, therefore, be made. As an example, the position of the chemical spinodal, calculated from the thermo-dynamic data of Sellars and Maak15 with the method described by Rundman and Hilliard,18 is included in Fig. 1. It is compared to the chemical spinodal calculated from the equilibrium miscibility gap by Cook and Hilliard's method.l9 Included is the coherent spinodal suggested by Golding and MOSS," using measured elastic constants for their calculations and the same ther-modynamic data. The spinodal estimated by Woodilla and Averbach,11 by determining the temperature limits for the observation of the satellites discussed above, is also given. Actually this last curve is open to question on the following grounds: As a phase boundary is approached the spacing of particles or the wavelength

Jan 1, 1970

By K. Tangri, M. Chaturvedi

On water-quenching from within the (a + ß) phase region Zr-2.5 Nb and Zr-2.5 Nb-0.5 Cu alloys can undergo w transfirmation. This transformation has been attributed to the enrichment of ß Zr phase, at the solution-treatment temperature, by the solute atoms. The ß—w transformation is accompanied by a hardening 01 the alloys and in the optimum condition w-bearing specimens of the ternary alloy are about 14 pct harder than those bearing only a' phase. On aging crl reverls thermally to more stable phases, which results in a considerable softening of the specirnens, as follows: w quenched -waged + ß Zr (enriched) waged - a + ß Nb The high-temperature bcc ß Zr in certain zirconium alloys can transform to a metastable w phase which has a primitive hexagonal structure. In the Zr-Nb alloy system w phase has been observed in the composition range of 7 to 15 wt pct Nb by a number of investigators.'-' In this composition range w can form by water-quenching ß Zr or by aging. known as athermal and thermal w, respectively. Hatt and Roberts' have found that thermal w has a constant c/a ratio of 0.622 +0.002 regardless of the composition and tha: the lattice parameters are of the order of a = 5.02A and c = 3.0 ?. The actual lattice parameters depend upon composition and the temperature of aging. The lattice constants of athermal w. however, depend upon alloy composition.3 The presence of w phase in zirconium alloys can cause substantial strengthening which has been attributed as probably due to the coherency between w and parent ß Zr phase. Robinson et al.' found that the presence of w can raise the strength of Zr-5.0 Nb-2.0 Sn and Zr-5.0 Mo-2.0 Sn alloys to about 170.000 psi: however. the ductility is considerably reduced. With the growing use of Zr-2.5 Nb and Zr-2.5 Nb-0.5 Cu alloys in the nuclear reactors, and the significant effect of w transformation on the mechanical properties of zirconium alloys studies were undertaken to study the w transformation in Zr-2.5 Nb and Zr-2.5 Nb-0.5 Cu alloys. This paper is concerned with the formation and reversion of w phase in these alloys. 1) MATERIALS AND EXPERIMENTAL TECHNIQUES The following two alloys were studied: 1) Zr-2.5 Nb-0.5 Cu (referred to as the ternary alloy): 2) Zr-2.5 Nb (referred to as the binary alloy). The chemical analysis of the alloys is given in Table I. The alloys, in the form of 3/8-in.-diam rods and 1/8-in.-thick sheets, were supplied by the Chalk River Nuclear Laboratories of the A.E.C.L. Initial fabrication for preparation of various specimens was carried out by cold rolling and swaging with intermediate anneals at 1000°C. All the heat treatments were carried out after the specimens were wrapped in zirconium foils and encapsulated in silica tubes under a vacuum of 5 x 10-% m of Hg. For optical metallography and hardness measurements disc specimens + in. diam by + in. thick were used. After the required heat treatments the specimens were mechanically and then chemically polished in a 45 pct HNO3, 45 pct H20. and 10 pct HF solution. The hardness measurements on the chemically polished specimens were carried out on a Vickers hardness tester using a 10-kg load. For each specimen at least fifteen indentations were made in order to obtain a representative hardness value. The phase identification and structural analysis were carried out using X-rays and electron diffraction techniques. Wires of 1.5 mm diam reduced to 0.12 mm diam by chemical etching were used for making Debye-Scherrer powder patterns using copper K-a radiations in 114.6-mm-diam camera. Thin films for transmission electron microscopy were prepared by electropolishing heat-treated a by 7 by 0.005-in.-thick strips using a modified Bollmann-Window technique. The 10 pct perchloric acid-90 pct methyl alcohol electropolishing bath was kepl at -5OCC and polishing was done at 5 to 10 v. The thinned specimens were washed in ethyl alcohol at -30" to -40°C and dried between filter papers. The thin films

Jan 1, 1970

By D. A. Elgillani, S. Atak, D. A. Rice, M. C. Fuerstenau, R. B. Bhappu

Quartz and feldspar cannot be floated with sulfonate at any pH; spodumene floats over a narrow acid pH range, while beryl responds moderately over a broad pH range. After wet-grinding in a steel mill, beryl, quartz, and spodumene float well with sulfonate below about pH 7, whereas the improvement in the response of feldspar is not so marked. A mechanism by which iron can be adsorbed on these minerals is presented. Also, the responses of leached, natural, and wet-ground beryl to amine, sulfonate, and oleate flotation are shown and related to the measured zero-points-of-charge of these materials. Earlier work with leached beryl showed that good flotation could be obtained with alkyl aryl sulfonate over a rather wide pH range using a Fagergren flotation cell.' When a similar response was observed with leached quartz, it was decided that unintentional activation was being obtained from the metallic components of the Fagergren cell. To obviate this difficulty, a microflotation cell was designed, and an experimental technique was devised. These have been described elsewhere. Experiments conducted with the small cell showed that leached quartz could not be floated at any pH with any sulfonate addition,3 which is in agreement with the observations of Kraeber and Boppel.4 Similarly, it was also found that leached beryl responded to sulfonate flotation only over a narrow pH range rather than the broad range reported earlier.1 This early work,1 however, revealed the important effect that wet-grinding in a steel mill has on the flotation response of certain silicates. That is, it was found that quartz and especially beryl floated well over an unusually wide pH range after wet-grinding in a steel mill. Microcline, however, floated poorly below pH 4, even though wet-ground under the same conditions. The work of Eigeles6 on adsorption of oleic acid on leached quartz and iron-contaminated quartz at constant pH is in agreement with these flotation data. Other research has shown that ferric iron, added as a salt to the system, functions as an activator in the narrow pH range in which Fe +++ iron hydrolyzes to its hydroxy complexes.3,5 These phenomena indicate that iron functions differently in flotation systems depending on its method of introduction. The object of this paper is to determine the mechanism by which iron is adsorbed on certain minerals, the mechanism of collector adsorption after iron abstraction, and the role that Fe++ and Fe+++ assume in the selective separation of these minerals. EXPERIMENTAL MATERIALS AND METHODS Sodium alkyl aryl sulfonate, mol wt 450,7 pure potassium oleate, and pure dodecylamine were used as collectors. All other chemicals were reagent grade in quality, i.e., n-amyl alcohol as frother; HC1, H2SO4, and KOH for pH adjustment; and ferric chloride as activator. Conductivity water, made by passing distilled water through an ion exchange column, was used in the experimental work. All minerals used in the investigation were hand-picked specimens. Sample Preparation: Each of the minerals was crushed through 8 mesh, and the product was divided into two groups, one to be ground dry and the other wet. Dry grinding was accomplished with an alumina mortar and pestle. The product was dry-screened to 48 x 150 mesh, cleaned magnetically, deslimed in conductivity water, and dried. Preparation of the samples by wet-grinding involved grinding a 200-g charge of the mineral (-8 mesh) at 60% solids with natural water in a mild steel rod mill for four minutes. This charge was then wet-screened immediately with natural water to 48 x 150 mesh, dried, and cleaned magnetically. Some experiments were also conducted with leached beryl and quartz. These products were prepared by leaching the sized sample (48 x 150 mesh) with concentrated HC1 with a percolation technique until no iron could be detected in the leach liquor. Following this step, the sample was rinsed with conductivity

Jan 1, 1967

By K. R. Janowski, H. Conrad

As part of a program to establish the effect of crystal imperfections on laser output, a detailed study was made of the dislocation structure of ruby crystals obtained from varioius sources. Using KHSO4 as an etchant, a detailed mapping of the dislocation structure on the (0001) and the (1150) planes was carried out. A less extensive study was made of the rhombohedral planes. The average dislocation density on the basal plane was 1.5 to 3 x 106 cm&apos;2 and on the (1120) planes -5 x 10&apos; cm-2. Howe7!er, considerable variation existed between areas on a given plane. The subboundaries in the basal plane tended to lie along [1100] type directions while those on the (1120) plane tended to lie: a) parallel to the basal plane, b) along truces of the (1101) plane, and c) along normals to the traces of the (0001) planes. The orientations suggest that mang of the dislocations lie on the (0001), (1701), and (1150) planes A Laue back-rellection nnalysis Of c-axis wander in one crystal revealed a gradual increase in misorientation from me end of the crystal to the other, with a maximum variation of 1°35&apos;. Slight etching of a mechanically polished crystal revealed mumerous polishing scratches, suggesting the existence of a plastic flow layer. It is recognized that chromium concentration, lineage, and other crystalline imperfections play a role in the efficiency of ruby lasers.&apos; Consequently, it is desirable to establish in detail the imperfection structure of ruby crystals to be used as lasers. Some exploratory work along this line had already been done by Barnes&apos; and Dils and Martin.&apos;" How- referred to as the morphological system, as described by Kronberg.4 The Miller indices given in the present paper will be based on this morphological system. In this system, the three common growth planes are the (0001), the {1120}, and the {1101}.5 Since these planes are of high stability, it is expected that they are most suitable for study by the etch-pit technique. In the present investigation, a detailed mapping of the dislocation structure was carried out for the (0001) and the (1130) planes. A less extensive study was made of the etch-pit structure on rhombohedra1 planes. An analysis of dislocations in sapphire (the ruby host) was first made by kronberg,4 who postulated that slip on the (0001) plane occurred by motion of dislocations with Burgers vector 1/3 <1150> and that these dislocations might dissociate into quarter partials. An etch-pit technique using boiling phosphoric acid was developed by Scheuplein and Gibbs6, 7 for identifying dislocations intersecting the (0001) planes and the planes near (2021) in sapphire. Al-ford and Stephens8 were able to reveal dislocations on the (0001) and {1120} planes in sapphire and ruby by etching in fused potassium bisulfate (KHS04) at 675°C. The termini of basal dislocations [(000l), <1120>] were revealed by Palmour and Kriegel9 on {1120} and {1010} by thermally etching sapphire. Bond and Harvey10 were able to decorate dislocations in sapphire by adding 1 pet by weight of ZrO2 to the Al2O3 powder used in the growth of the crystals by the Verneuil technique and then heating the grown crystals for 4 hr at 1500°C. They found, using optical transmission microscopy, that many dislocations had straight segments which were parallel to one of the six [1120] directions in the basal plane. Single dislocation lines curved smoothly from one alignment to the other, turning through angles of 60 to 120 deg. Also observed were isolated hexagonal loops, approximately 10 µ in diameter, the sides of which lay along the same directions as did the longer dislocations. MATERIAL AND ETCHING PROCEDURE The ruby specimens used in this study (all containing approximately 0.04 pet Cr) had been obtained from four different sources: Linde Co., Meller Co., Valpey Crystal Corp., and those grown at Aerospace Corp.* For the initial phase of this study, several specimens were cut from the slab shown schematically in Fig. 1 which had previously been cut from a disk boule obtained from the Linde

Jan 1, 1964

By A. W. Sommer, H. H. Kellogg

It is shown that SO3-O2 mixtures react with sphalerite at an appreciable rate ill the temperature range of 361° to 527°C to fornz ZnSO4. The rate of reaction follows a parabolle lax. Oxygen, or O2-SO2 mixtures, have a negligible effect on sphalcrite in the same temperatuee range. PRACTICAL roasting of sphalerite is usually performed at 800°C or higher. The calcine is composed of zinc oxide unless the roaster atmosphere contains relatively large amounts of SO2 and the temperature is held to 800oC or lower, in which case zinc sul-fate may also form. Ong, Wadsworth, and assell&apos; have made a careful kinetic study of sphalerite oxidation under these "normal conditions" and have concluded that the rate of the reaction is controlled by the decomposition of an activated complex adsorbed on the sphalerite surface. They found the rate of oxidation to be small at 700°C. Extrapolation of their data to 400°C would indicate an almost negligible rate at this temperature. In our work sphalerite was reacted with air, mixtures of SO2, O2, and N2, and mixtures of SO3, O2, and N2 in the temperature range 361o to 527OC. Negligible rates of oxidation were found, except for the gas mixtures containing SOs. With this latter gas, the oxidation of finely divided sphalerite was fairly rapid and zinc sulfate was the product. Based on the limited evidence available, the rate of sphalerite oxidation by SO3 is postulated to be controlled by gaseous diffusion through pores or cracks in the zinc-sulfate coating. This evidence for the direct reaction of sphalerite and SO, at low temperature may prove of importance to the understanding of zinc-sulfate formation in the dust-collecting equipment usually associated with zinc roasters. The roaster gas carries off fine dust, much of which may be unreacted sphalerite. The temperature in dust-collecting equipment drops from the roaster temperature (about 800°C) through the range of temperature we studied, to ambient temperature. Such dusts are known to contain far larger amounts of zinc sulfate than the primary calcine. It has been assumed in the past that this sulfate is formed by reaction of ZnO dust with SO3 (or SO, plus 0,) in the partly cooled gases. Our work shows that an alternative possibility exists—the direct reaction of SO3 with ZnS dust. EXPERIMENTAL Reaction rates for sphalerite at 350° to 600°C are relatively small so that it was necessary to use finely divided material with a relatively large surface area in order to obtain measureable amounts of reaction. In the preliminary experiments, pure mineral sphalerite, ground to pass a 325-mesh sieve, and chemically precipitated ZnS (in the form of an impalpable powder) were used. In the quantitative rate experiments the ground mineral sphalerite was processed in an Infrasizer to obtain a product with particle size between 9 and 18 µ. The analysis of this material was 66.7 pct Zn, 0.09 pct Fe, and 32.7 pct S (theoretical sphalerite is 67.1 pct Zn, 32.9 pct S). The sized powder was carefully mixed and divided into l-g samples. The apparatus used for the quantitative rate measurements is shown in Fig. 1. For the preliminary experiments the following change was made: The external catalyst furnace (B, C)* was not used. *Letters refer to Fig._______1 .___- Rather, when catalysis of the SO2 + O2 reaction was desired, the glass beads in basket M were replaced by vanadium-oxide pellets. Procedure—A l-g sample of ZnS was placed on a shallow stainless-steel tray, I, and spread evenly to a depth of about 1mm. The tray was placed in the reaction assembly and the assembly inserted in the cold furnace. The furnace tube was flushed with dry argon and then heated to the desired reaction temperature. The temperature was controlled to ±0.5oC. Gas mixtures (O2 + N2 or O2 + SO2) were prepared from tank gases by means of a mixing device identical to that employed by Darken and Gurry.2 The total flow rate of gas was 205 ml per min to point A of Fig. 1. The accuracy of the individual and

Jan 1, 1960

By T. E. Leontis

Data are presented in this paper to show that addition of zirconium to sand-cast Mg-Th alloys effects a marked decrease in the grain size of these alloys which is accompanied by a significant increase in the mechanical properties over the entire range of thorium content investigated. The beneficial effect of zirconium on the strength properties is maintained at elevated temperatures up to 700°F. In addition the alloys exhibit exceptionally high creep resistance at temperatures up to 600°F. Zirconium does not greatly improve the strength or creep characteristics of extruded Mg-&apos;Th alloys. Cerium is not a desirable addition to Mg-Th-Zr alloys. IN a previous paper,&apos; it was shown that addition of thorium to magnesium imparts exceptionally high resistance to creep at elevated temperatures both in the sand-cast and in the extruded states. The large grain size of the sand-cast alloys, however, renders them of questionable value as engineering materials. Sauerwald² showed that the grain size can be reduced effectively by the addition of zirconium. Results of a detailed study of the properties of Mg-Th-Zr alloys over a wide range of thorium content are presented in this paper. In accordance with the preliminary findings of Sauerwald,² it is shown here that Mg-Th-Zr alloys possess the unusual combination of fine grain size and a high level of strength and creep resistance at elevated temperatures. Some information on the effect of cerium on the properties of Mg-Th-Zr alloys is presented also. Effect of Th on Solubility of Zr in Molten Mg Sand-cast test bars and 3 in. diam extrusion billets of Mg-Th-Zr and Mg-Th-Ce-Zr alloys* were pre- pared according to the procedures described in the previous paper.&apos; The zirconium was added in the form of sponge metal as supplied by the Bureau of Mines.&apos; The maximum amount of zirconium that usually can be introduced into magnesium at the customary alloying temperature of 1350° F is about 0.7 pct. The analyses in Table I clearly show that thorium in- creases the solubility of zirconium in liquid magnesium. The tabulated zirconium contents are designated as "acid soluble;" this serves to distinguish these values from the small amount of zirconium that is not dissolved when the alloy is subjected to the action of a dilute acid solution. The "acid-insoluble" zirconium is believed to be ineffective as an alloying ingredient. The acid-insoluble zirconium contents ranged between 0.03 and 0.16 pct in the present alloys, the tendency was toward higher values in alloys with higher thorium content. In contrast to the effect of thorium, cerium decreases the solubility of zirconium in magnesium. This is shown by the three Mg-Th-Ce-Zr alloyst in- cluded in Table I and stands in agreement with the observations of Nelson and Stricter".&apos; on Mg-misch-metal-Zr alloys. Effect of Zr on Grain Size of Mg-Th Alloys The potent effect of zirconium as a grain refiner has been demonstrated for many types of magnesium alloys.3-8 Of greatest importance to date are Mg-Zn-Zr alloys5,6,8 and Mg-mischmetal-Zr alloys.3,4,7 Zirconium has also been found to exert a marked grain-refining action on Mg-Th alloys. All the Mg-Th-Zr alloys cast in the form of ½ in. diam test bars have an exceedingly fine grain size (Table I). Reference to the previous paper&apos; will show that binary Mg-Th alloys containing up to 6 pct Th are almost completely columnar even in the M in. diam reduced section of a test bar, and that 10 to 50 pct Th alloys have an equiaxed grain structure of 0.03 to 0.08 in. The data in Table I also show that addition of cerium to Mg-Th-Zr alloys has no effect on the grain size. In addition to increasing the strength properties, the fine grain size of Mg-Th-Zr alloys

Jan 1, 1953

By O. P. Arora, M. Metzger, G. R. Ramagopal

The rates of grain boundary and general corrosion were surveyed by an approximate method. Quantitative differences between their variations with the strength or cupric ion content of the acid yielded large variations in their ratio, highly selective intergranular attack being observed only under specific chemical conditions. The boundary corrosion rate increased with the copper content of the aluminum; this was attributed to an autocatalytic effect similar to the one shown for general corrosion. High- purity aluminum in hydrochloric acid exhibits striking intergranular corrosion and other structure-dependent corrosion phenomena of fundamental interest. The behavior is highly sensitive to the metallurgical and chemical conditions, the significance of many of which has not been established. The features of the intergranular-corrosion phenomenon, first described by Rohrman,l are summarized in the remainder of this paragraph. Strong attack normally occurs only at high-angle grain boundaries.&apos; Usually 15 to 25 pctHCl is used to obtain a high rate, but this has also been obtained with weaker (7 to 15 pct) acid either by adding cupric or ferric ion to the acid3-5 or by passing an anodic current (-0.1 ma per sq cm).2,3,5,6 The two latter corrosion conditions produce strong attack of low-angle boundaries after certain heat treatments 2-4,5,7 The susceptibility of high-angle boundaries is influenced by the grain-boundary segregation of iron atoms; this increases the slow (µ per month) attack in 10 pct HCl8 but diminishes the rapid (mm per month) attack in 20 pct Hc14 (the present and most previous investigations deal with rapid attack). That segregation of elements other than iron affects intergranular corrosion has not been demonstrated, although analysis of data for iron alloys indicated that at least one other element must be considered.9 Intergranular attack occurs over a wide range of purity although it begins to become obscured above several hundred parts per million (ppm) total im- purities by the severe general corrosion which accompanies the higher iron contents and which is associated with the presence of a second phase or an inhomogeneous distribution of the dissolved iron.4,6,10 The variation of intergranular-corrosion rate with heat treatment1&apos;3-6&apos;"10 can be explained in some cases in terms of the distribution of the iron impurity but is not in general adequately understood. The present work dealt with two questions not previously considered in detail. The first proceeded from the view that the extent to which a special behavior is associated with the boundaries is indicated not by the intergranular corrosion rate alone but by the ratio of the intergranular to the general corrosion rate. A comparison of the two rates was therefore made for one lot of aluminum in acids of varying strength and metallic ion content. The second question was the effect of the copper content of the aluminum. For general corrosion, it has long been known that copper ions introduced into the acid by corrosion of the solid solution are reduced on the aluminum as patches of elemental copper which enhance the corrosion rate by providing cathodes of lower hydrogen overvoltage than were originally present.&apos;&apos;-&apos;3 Since the copper patches remain themselves unchanged, their action is "catalytic", and since they are products of corrosion, the effect is "autocatalytic." This phenomenon is significant at copper levels much lower than previously suspected, even at those typical of high-purity aluminum, as the authors have shown in a previous paper.l4 The present work shows that copper content affects intergranular corrosion. With polycrystalline specimens, truly quantitative rate measurernents are not readily made for intergranular corrosion or for general corrosion in the presence of rapid intergranular attack, and previous work in this field has tended to be qualitative. The present study made use of a simple procedure which provided fair approximations to the quantitative corrosion rates and fitted the purpose of surveying the behavior over % wide range of conditions and displaying certain large effects. The approximations involved in this work were usually outweighed by the experimental scatter, which tends to be substantial in a system as sensitive as this one. I) EXPERIMENTAL A. Material. The material procured, Table I, represented three low copper (1 to 3 ppm) lots, two of "normal" copper content (21 and 22 ppm), and two

Jan 1, 1962

By Y. Kondo, S. Yamazaki, Z. Asaki

Thermal deco7nposition of Pyrite particles in a fluidized bed with inert gas stream was studied. Assuming that heat transfer from the surroundings to the fluidized particles controls the overall decomposition rate, rate equations for the batch process and for the continuous process were derived. In the batch experiment, a linear rate equation satisfies the experimental results and the overall heat transfer coefficient calculated from the rate constant agrees fairly well with that obtained by Leva.l1 For the continuous process, two rate equations were derived, one on the assumption of complete mixing of particles and another on the upward piston flow of particles in a fluidized bed. The former holds for a bed containing a higher fraction of decomposed pyrite realized at lower feeding rates. The latter can be applied for a bed at higher feeding rates. Thus, segregation of particles in the fluidized bed was indicated at higher feeding rates. Bed temperatures also correspond to these conditions. ThERMAL decomposition of pyrite may be represented by Eq. [I]. The pressure of diatomic sulfur gas reaches 1 atm at about 690°C. The thermodynamics,&apos; kinetics,2&apos;3 composition, and properties3-5 of decomposed products of such a reaction have been studied. Pyrite is a very common sul-fide mineral and is often accompanied with other sul-fides. It is of basic interest in nonferrous metallurgy to clarify the behavior of pyrite in the pyrometallur-gical processes of sulfide minerals of metals such as copper, lead, zinc, nickel, and so forth. Interest in this reaction increased recently because of possible elimination of arsenic from pyrite in processing highly purified iron oxide pellets. Producing elemental sulfur from pyrite, instead of sulfuric acid, also aroused interest in this reaction. It is indicated that the thermal decomposition of solid particles, such as calcium carbonate, proceeds through three major sequential steps: heat transfer, interfacial chemical reaction, and mass transfer.637 It is known that the decomposed product of pyrite is very porous2, 3 and the diatomic sulfur gas evolved can easily escape through this layer of decomposed product. It depends upon the circumstances, therefore, whether the heat transfer to the interface within particles or the chemical reaction at the interface determines the overall decomposition rate. The enthalpy change in the decomposition of pyrite is about 33 kcal per mole FeS2 which is comparable to that of calcium carbonate. The decomposition of calcium car- bonate becomes more and more dependent on the rate of transport of heat when reaction temperature increases, such as occurs in a fluidized bed.6&apos;7 It is reasonable to presume, therefore, that the thermal decomposition of pyrite, an endothermic process, carried out in a fluidized bed may be analyzed according to the heat transfer controlling model. This work intends, first, to propose a mathematical model that determines the overall rate in a fluidized bed for the decomposition process and, second, to investigate a few characteristics of the fluidized bed based upon the experimental results obtained. KINETICS OF THERMAL DECOMPOSITION IN A FLUIDIZED BED It is intended in this section to obtain rate equations for thermal decomposition of pyrite in a fluidized bed by assuming that the overall rate is determined by heat transfer from the surroundings to the particles. Both batch and continuous processes are considered. 1) Batch Process. To obtain the rate equation in the batch process, the following two additional assumptions are made. First, the temperature of preheated inert gas, tg, blown into the fluidized bed is assumed to be the same as the temperature of the fluidized bed, tf. Thus, no heat exchange occurs between the gas and particles in the bed and only the heat transfer from the reactor wall kept at tw to the particles is to be considered. Second, the decomposition is assumed to start at the outer surface of the particles and to proceed toward the center. At any given time during decomposition, undecomposed pyrite remains in the tori at a temperature: td. The decomposed shell is composed of FeS1+x whose outer surface is at tp Diatomic sulfur gas evolving at the interface is heated to tf during its escape through the decomposed shell. This is illustrated in Fig. 1. With the above-mentioned assumptions of heat transfer, we have:

Jan 1, 1969

By D. T. Peters, J. C. Bisseliches, J. W. Spretnak

The pain boundary relaxation phenomenon in high-purity copper, 0FHC copper, and a precipitation-hardenable alloy o-fCu-2 uit pct Co has been studied by internal ,friction and elastic aftereffect techniques. The data were analyzed by assuming the broad distribution of relaxation times observed obeys a lognormal distribution law which enables calculation of the relaxation strength. Grain size had no effect on relaxation strength, although the peak width increased with increasing grain size and decreasing temperature. A double grain boundary peak was produced in high-purity copper by annealing to produce secondary recrystallization. The activation energy measured for 99.999 pct Cu is 37.5 * 3 kcal per mol and 46.5 kcal per mole for OFHC copper. A small peak in the Cu-Co alloy at about 220°C at 1 cps was deduced to be the grain boundary peak. Its height increased and its activation energy decreased with increasing aging time. Except for erratic peak positions the observations were consistent with the theory of pain boundary sliding. BEFORE the mechanism of the grain boundary internal friction peak in metals can be satisfactorily explained, the detailed characteristics of the relaxation process must be documented. Of interest are the effect of grain size on relaxation strength, the high-temperature background, and peak width and position. The effect on the grain boundary peak of a precipitate at grain boundaries and of the change in distribution of the particles with aging time must also be explained by any existing or forthcoming theory. The model which has received the most attention was proposed by KG&apos; and zener2 and proposes that the anelastic strain results from sliding of adjacent crystals at grain boundaries. The sliding is limited by the interlocking of grain corners. It follows, according to this model, that the relaxation strength is independent of and the relaxation time is proportional to the grain size. The proportionality between grain size, D, and relaxation time, t, has been confirmed by K&&apos; and Bisseliches . In this case, the internal-friction peaks of various specimens can be superimposed by plotting Q-&apos; as a function of the parameter vD exp H/RT where v is the frequency and H the activation energy. However, the data of Starr et 01.&apos; and Leak6 fit better to a parameter containing D to an exponent near two. A meaningful relationship is not always deducible from the shift of peak temperature with grain size. KG7 demonstrated that a twofold variation in grain size obtained by varying the amount of cold work followed by identical recrystallization anneals will cause a peak shift that is too large to be accounted for even by an exponent of two. Since the decreased grain boundary area existing with a larger grain size is exactly compensated for by an increased sliding distance, the relaxation strength should not decrease with increasing grain size. The height of the internal-friction peak has generally been observed to be rather insensitive to grain size as long as the average grain diameter does not approach the specimen diameter. Exceptions have been reported by Koster, Bangert, and Lang8 for copper, and by Leak6 for iron. The observations for copper could well have been confused by the presence df 0.3 pct0. The possibility that the peaks may simply be increasing in width with increasing grain size and that the relaxation strength, which is proportional to the area under the peak, may remain constant was not examined. his point has been checked in this investigation using high-purity copper. Atomic mechanisms to account for damping by sliding at grain boundaries have been proposed by KG7 and Mott. KG predicts the activation energy to be identical to that for self-diffusion. Mott&apos;s "island" model suggests the activation energy is nL where n is the number of atoms in an island and L is the latent heat of fusion per atom. Other authors have felt that a value equal to the activa-

Jan 1, 1964

By Donald B. Evans, Robert D. Pehlke

The solubility of nitrogen in liquid Fe-B alloys has been measured up to the solubility limit for the formation of boron nitride. The activity coefficient of nitrogen increases with increasing boron content in the range 0 to 7 wt pct B. From experimen -tal data, values have been calculated for the B-N interaction parameter e3 at temperatures in the range 1550" to 1750°C. A value of 0.038 has been estimated for the boron self-interaction parameter eg at 1550°C. The standard free energy of decomposition of boron nitride into the elements dissolved in liquid iron has been determined to be: ?F° = 45,900 -21.25T in the range from 1550° to 1750°C. The nitride is assumed to be of composition BN. BORON nitride has an unusual combination of properties which make it appear attractive in a wide range of engineering applications. Some of its more important and most recent applications are in the nuclear area, particularly in connection with the liquid-metal cooled reactor concept now receiving considerable emphasis. Boron nitride has a high degree of stability at elevated temperatures. It also has excellent ma-chinability and the ease with which its crystals deform suggests applications as a lubricant. These properties stem from a hexagonal layer-type structure similar to the structure of graphite. One of its primary uses to date has been for seals in liquid-metal pumping systems. It is also used in nuclear reactors as an insulating layer to separate two solid metals which are not themselves compatible under the conditions of temperature and atmosphere in which they are used. Its inertness to liquid metals has also suggested use as a mold-release agent in casting processes. In addition to its excellent machinability and reported inertness to liquid metals such as iron, silicon, aluminum, copper, and zinc, boron nitride has high thermal conductivity and excellent thermal shock resistance. This combination of properties would make it appear ideal as a refractory crucible material for refining of high-purity liquid metals, for example high-quality steels. However, since it is known that concentrations of boron as low as 50 ppm can have a marked effect on the physical properties of certain steels,&apos; in particular on the creep and stress-rupture properties, an investigation was undertaken to define accurately the chemical equilibrium among boron, nitrogen, and liquid iron in the range of steelmaking temperatures. EXPERIMENTAL PROCEDURE Two experimental approaches to this problem were employed: a Sieverts&apos; method and a quenching method. In the first method, the Sieverts&apos; technique was used to measure the equilibrium nitrogen solubility in liquid Fe-B alloys of 0 to 7 pct B as a function of nitrogen gas pressure over the melt. The solubility limit of the boron nitride phase formed was determined by the point of departure of the nitrogen absorption from Sieverts&apos; Law. This technique has been applied to liquid Fe-Ti alloys by Rao and parlee,&apos; to liquid Fe-A1 alloys by Evans and Pehlke,3 and to solid Fe-V alloys by Fountain and Chipman.4 In the second method a melt of liquid iron was held in a crucible of boron nitride under a known partial pressure of nitrogen gas. After thermodynamic equilibrium was attained, the melt was quenched in a stream of helium and then analyzed by wet-chemical methods for boron and nitrogen. The Sieverts&apos; apparatus used in the first method was essentially of the same design as the one described by Pehlke and Elliott.5 The charge materials were vacuum-melted high-purity iron (Ferro-vac E) supplied by the Crucible Steel Co. and -325 mesh boron powder supplied by Cooper Metallurgical Associates of Cleveland, Ohio. The boron contained less than 0.02 wt pct O, according to supplier&apos;s analysis. Recrystallized alumina crucibles were used to contain the melt. Examination of solidified melts showed these crucibles to be satisfactory with no evidence of any reaction or physical penetration of the crucible wall by the melt. The melt temperature was measured by a disappearing filament-type optical pyrometer sighted vertically downward on the melt surface through a 1/4-in.-diam sight hole in the crucible lid. The pyrometer was calibrated against the melting point of pure iron in the same apparatus, taking the emissivity of

Jan 1, 1964

By E. A. Farrell

A comprehensive survey is made of the status of the asbestos industry as it relates to marketing the product. Included are descriptions of the various types of asbestos and the grading and classification systems used. The uses of asbestos, distribution practices, and types of ore bodies are all related to marketing. World production, the producers and their capacities and world consumption for 1966-67 are summarized and statistical data are included. Asbestos is a general term describing a family of fibrous minerals of the serpentine and amphibole mineral groups. Asbestos has a long history going back to the time of the Egyptians, when it was used as a lamp wick. The commercial mining of asbestos started in Canada, Russia, and Africa in the 1800&apos;s, and the first asbestos products were made in Italy and Russia. The five main types of asbestos are: chrysotile, accounting for 95% of the total mined, amosite, crocido-lite, anthophyllite, and tremolite. Canada, Russia, and Africa are the major producers of asbestos. The commercial utility of asbestos was at first based on the heat resistance of the fibrous mineral in the form of packing, at the start of the industrial revolution. Its current utility is based more on its ability to reinforce binders such as portland cement, rubber, and plastics. Its inertness to the chemical nature of most binders is unique. Most important is its ability to maintain its reinforcing utility when the product is exposed to weather and soil conditions as in asbestos cement boards and pipe, and heat, pressure, and chemical exposure as in brake linings and gaskets and packings. The mineral asbestos is also unique because its fibrous form permits it to be spun and woven to cloth or formed into paper. Many asbestos applications are critical to national defense and at the present time, there are no satisfactory substitutes. Grading and Classification Canadian chrysotile asbestos fiber is graded and priced by length since basically the longer the fiber the higher the utility. The Canadian asbestos industry does not, however, classify the fiber by direct length measurement, but by a dry screening test. The method is called the Quebec Standard Screen (QS) test. One pound of fiber is mechanically shaken in four vertically stacked sieve boxes. The relative proportions remaining on the sieves defines the grade. The longer the fiber, the larger is the amount that stays on the top coarse screens and the less on the lower, finer mesh screens. Other tests can be used to further define the length distribution of fiber such as the wet screen Bauer McNett and the Suter Webb Comb (3 group only). The Canadian grading system divides the milled fibers into 5 main groups: group 3, 4, 5, 6, and 7, with 3 group being the longest, and 7 the shortest. Each group is further divided to subgrades, identified in each group by the letters A to Z, with "A" the longest and "Z" the shortest. See Appendix 1 for the Canadian QS classification system. The Russians also use the QS test on chrysotile. The Africans classify their chrysotile into grades similar to Canadian. The African crocidolite and amosite, however, are classified into actual length groups such as l to 2 in. and 2 to 3 in. Amosite and crocidolite are generally longer than chrysotile but also more brittle. Milled asbestos is not composed of staple length fibers like fiber glass or cotton, but of a mixture or blend of fibers ranging from long to short. Milled asbestos has a fiber length distribution similar to the particle size distribution of a powder. For example, the longest group 3 chrysotile grades have a high percentage of the longest fibers (1/2 to 3/4 in.) and low percentage of short fibers (0.003 in.). The figures in Table 1 give the approximate length distribution of the longest, middle, and shortest groups. A second and further method of classifying fiber is the degree to which the fiber bundles are separated to form a larger number of smaller diameter bundles. This property is normally described as the degree of fiberization, openness or surface area. Air permeability tests are used to measure surface area. Asbestos pro-

Jan 1, 1971

By S. R. Balajee, I. Iwasaki

The interaction between British gum 9084 and dode-cylammonium chloride (DAC) at quartz and hematite surfaces was established from coadsorption studies and streaming potential measurements. The cationic DAC interacts with the somewhat anionic British gum 9084, leading to the formation and adsorption of a binary complex of DAC-British Gum 9084 at the interface. The parallel ability to depress quartz along with hematite as a result of the interaction between DAC and British gum appears to be the main reason for the ineffective depressant action of starches and starch derivatives in the cationic flotation of iron ores. Amines are not particularly selective collectors for the flotation&apos; of siliceous gangue from iron ores and, therefore, a suitable iron oxide depressant is needed for a satisfactory separation. Various starches and their derivatives have been extensively tested with oxidized iron ores,&apos;-3 and it has been empirically established that British gums and dextrins are preferable. However, for the flotation upgrading of magnetite-taconite concentrates from 8 or 8.5% Si O2 to about 5% Si 02, British gums, which have been used so successfully on oxidized iron ores, have been found to have no effect and oftentimes are actually deleterious.4 In previous articles,5-7, starches were shown by adsorption measurements, flotation tests, and floccula-tion tests to interact with calcium ions in solution, and it was thought that a study on the interaction between starches and dodecylammonium ions would be able to shed some light on the anomalous flotation behavior described above. In fact, starches are known to interact markedly with paraffin-chain-type surface active agents and, thereby, to precipitate the starch or inhibit the iodine-starch reaction.8 From X-ray diffraction studies and viscosity measurements, the formation of a helical complex between mylose and a surface active agent has been postulated.9 The interaction with other types of hydrophilic colloids, such as synthetic polymers and proteins, has also been investigated and is usually explained in terms of van der Waals&apos; force interaction and/or ion-ion interaction. In the present investigation, the interaction of British gum and dode cylammonium chloride on quartz and hematite was studied by adsorption and streaming potential measurements in an attempt to establish the mutual adsorption behavior of British gum and dode-cylammonium chloride on mineral surfaces and to clarify the anomalous depressant activity of British gum in the cationic flotation of iron ores. All the measurements were carried out at a natural pH of near 7 because dodecylammonium chloride gives maximum selectivity of flotation separation at this pH2 and to avoid any third parameter in the system. EXPERIMENTAL MATERIALS AND METHODS Minerals: The quartz and hematite samples used for the adsorption tests were prepared as described in a previous paper,"J except that the specific surfaces of the samples were increased to 5,860 and 16,000 Sq cm per gm, respectively. For the streaming potential measurements, the 48165-mesh fractions screened out of the original samples were etched with hydrochloric acid, washed repeatedly with water, and stored under water in Pyrex bottles. Reagents:DodecyIammonium chloride (DAC) was prepared1 1 by bubbling dry hydrogen chloride gas through a benzene solution of high-purity dodecylamine supplied by Armour and Co. British gum 9084, received from Corn Products Co., was solubilized by first dispersing it in water to produce a 0.05% solution and then homogenizing it in a blender for 5 min. Distilled water was used in the preparation of the samples and the solutions and for all test work. Adsorption Measurements: The procedure for the adsorption density determinations was also the same as that described in the previous paper.1° The residual concentrations of the British gum and the DAC in the supernatant solution were analyzed colorimetrically by the phenol-sulf uric-acid and amine-picrate methods, respectively. The validity of the mine-picrate method for the colorimetric analysis of DAC in the presence of British gum and the analysis of British gum in presence of DAC were checked by establishing calibration curves between optical density and concentration. Streaming Potential Measurements: The cell assembly for the streaming potential measurements was similar to that described by Fuerstenau.&apos; The streaming potential

Jan 1, 1970