Search Documents

By C. H. Curtis

THE valuable mineral content of the current feed to the Miami concentrator is as follows: copper, 0.7 pct total; molybdenum, 0.01. Flotation of this ore yields a sulphide concentrate containing: chalcocite, 44 pct; molybdenite, 0.5; pyrite, 50.0; insol, 5.5. A combination of potassium ethyl xanthate and pentasol amyl xanthate as collectors, and pine oil, as frother, are used in this flotation. Rejection of pyrite is encouraged by holding the amount of collectors used to the minimum consistent with copper recovery and by operating at high alkalinity (equivalent to 0.35-0.40 lb CaO per ton solution of pH 11.0).

Jan 1, 1950

By John V. Beall

On January 1, 1948, we boarded the cage at 7 a.m. and were dropped to the 900 level of the Brunswick shaft. The previous evening, we had attended the New Year's party at the Miners' Guild Hall and as this soireée had not disbanded until the small hours of the morning, we had only had about two to three hours sleep. At the 900 level station, we fell in beside our mining partner, a Cousin Jack, who was known by all as Porky. Porky didn't say anything as we plodded down the drift, we didn't say anything either-in fact there was little conversation by anybody.

Jan 1, 1971

ENROLLMENT of both undergraduate and graduate mineral engineering students rose approximately 11.8 pct over last year to a total of 12,830. Leading again in the enrollment climb was ceramic engineering which increased by about 21 pct. Approximated increases in enrollment of the other mineral engineering categories, in order, were: metallurgical 17.7 pct; petroleum 13.3 pct; geological and geophysical 3.3 pct: and mining proper, the lowest with 2.9 pct. Total ECPD school enrollment climbed to 242,405 -just below the 1947 peak, but 14.4 pct higher than 1955. Engineering enrollments have shown a general increase since 1951, and freshmen enrollments have climbed steadily since 1950.

Jan 5, 1957

Organization Place Date 1919 National Drainage Congress St. Louis, Mo. Nov. 11-13 American Mining Congress St. Louis, Mo. Nov. 1.7-21 Canadian Mining Institute Vancouver, B. C. Nov.. 26-28 American Society of Mechanical Engineers:.... New York, N. Y. Dec. 2-5 American Institute of Chemical Engineers Savannah, Ga. Dec. 3-6 Geological Society of America...; Boston, Mass. Dec. 29-31. American Society of Heating and Ventilating 1920 Engineers New York, N. Y. Jan. Mining and Metallurgical Society of America ... New York, N. Y. Jan. 13. American Institute of Min. and Met. Engineers... New York, N. Y. Feb. 16-19 American Ceramic Society Philadelphia, Pa. Feb. 23-26

Jan 11, 1919

[Trans. No,PlaceDate Vol. Page1 1. Wilkes-Barre, Pa*May, '71 13 2, Bethlehem, Pa Aug., '71110 3, Troy, N. Y Nov., '71.. 113 4. Philadelphia, PaFeb,, '72.. 117 5, New York, N, Y.*May, '72,, 120 6. Pittsburgh, Pa Oct,, '72,, 125 7. Boston, Mass Feb,, '73.. 128 8. Philadelphia, Pa,*May, '73., 23 9. Easton, PaOct., '73., 27 10. New York, N, Y Feb., '74,, 211 11. St. Louis, Mo,*May, '74.. 33 12, Hazleton, PaOct., '74., 38 13, New Haven, ConnFeb., '75., 315 14. Dover, N. J,*May, '75.. 43 15, Cleveland, 0Oct,, '75,, 49]

Jan 1, 1928

By Charles H. Jacoby

The solution mining of evaporites has a history of approximately 5,000 years. The insitu leaching of metalliferous ore will have many of the same characteristic problems which have confronted industry for years in the production of evaporite minerals. Basically we will be converting the less soluble forms of valuable metals into their more soluble salts and producing these in much the same manner as, for example, sodium chloride. There are a number of problems which we are faced with that are more complex and complicated and, therefore, will require a higher degree of sophistication than previously employed. One of our most important undertakings will be the clearcut definition of the problems involved. While a great deal of expertise can be drawn from the solution mining of evaporites and the oil industry, problems peculiar to the hydrometallurgical field will need to be solved. One of these is the introduction of permeability into an impermeable rock so as to expose the sought after values of metals which by volume are infinitesimal when compared with sodium chloride, potash or other type water soluble mineralization. After establishing this permeability which will be miniscule when compared to a solution cavity, there will be the maintenance of this permeability. In general, salt deposits are of a somewhat uniform chemical composition and thus their chemistry was relatively simple. Each metalliferous ore body is somewhat unique in its chemistry and will need to be treated accordingly.

Jan 1, 1974

By Douglas D. Donald

The New Jersey Zinc Co. successfully holed through a 2 1/2-mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial addi- tional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine. After careful consideration of all possible methods of transporting this volume of ore from Ivanhoe to the mill, it became evident that diesel locomotive haulage through a 2½-mile tunnel between the two mines would best suit prevailing conditions. Since the lowest operating level, known as the 1100 level, of each mine would be at approximately the same elevation, it was obvious that such a tunnel should be driven on this level. Not only would this tunnel facilitate feeding Ivanhoe ore into the underground crusher and skip loading installation at Austinville, but it would also open up a known orebody 5000 ft southwest of the Van Mater shaft. In addition it would provide a valuable diamond drilling base from which a large and a potentially favorable but untested block of ground might be explored. In order to hasten the completion of the tunnel, it was felt that it should be driven from both ends. ENGINEERING CONTROL PROCEDURES It was vital that the tunnel junction be made accurately on line and grade; thus it was felt that engineering control of an unusually high degree of reliability was required to prevent an accumulation

Jan 1, 1959

By E. R. Johnson

The copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the westem flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past I5 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7½ gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by I-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55½-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73½-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bill serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 13/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7½ McCully gyratory crusher set at 13/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73½ by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1949

By Barry D. Lichter, Pierre Sommelet

High-temperature heat contents of InSb, GaSb, and AlSb were measured over the temperature range 400" to 1450°K using a diphenyl ether drop calorimeter. Smoothed ualues of the thermal properties, H$ - H:9s, have been derived and are tabulated at even temperature intervals. The heats of fusion of the three compounds were determined as, respectively, 5707 *100, 7780 * 100, and 9800 5 3011 cal per g-atorn at the determined melting points of 797" l°, 985" * , and 1330" * 5°K. The calculated entropies of fusion are, respectively, 7.16 0.12, 7.90 * 0.11, and 7.37 * 0.23 cal per deg per g-atotn. The heat capacities increase substantially on tnelting in contrast to the behauior of structurally related germanium and silicon. Deriations from the Kopp-Neumann rule are negative for solid compounds and positive for the liquid phases. Previously obsevrrd "post melting" in InSb is confirmed. The high-temperature thermal properties of 111-V compounds are presently not well-established, despite the technical importance of these semiconducting cbmpounds. Uncertainties in available heats of fusion and heat contents have seriously hampered thermo-chemical evaluations' and thermodynamic analyses of phase equilibria2"" in these systems. This paper reports results of high-temperature heat content investigations of InSb, GaSb, and AlSb measured in the range 400" to 1450°K employing a diphenyl ether drop calorimeter. Similar measurements for InAs and GaAs will be reported in a following publication.~ EXPERIMENTAL PROCEDURES Samples. High-purity samples of the compounds InSb and GaSb were supplied in the form of crushed crystal fragments by Dr. Carl Thurmond of the Bell Telephone Laboratories and in the form of single crystals by Dr. A. Strauss of the M.I.T. Lincoln Laboratory. Single-crystal samples of semiconductor-grade AlSb were supplied by Dr. W. P. Allred of the Bell and Howell Research Center. Chemical analyses indicated that all compounds were stoichiometric to *0.1 at. pct, which is within the experimental uncertainties of the analyses. Samples were crushed, weighed, and encapsulated in evacuated, thin-walled, fused silica capsules. The capsules were nearly identical in external shape, 2 cm by 2 cm diam, but varied in weight due to differences in wall thickness. One sample of AlSb was contained in a thin-walled, high-purity alumina cup encapsulated in silica and used for heat content determinations of liquid AlSb. The capsule materials showed no visual evidence of reaction with any of the compounds. The sample and capsule weights are given in Table I. Calorimeter. A Bunsen-type calorimeter, similar in design to a previously described instrument6 but employing diphenyl ether (C6H5)'0 as the calorimetric substance, was used for measurements of heat contents above 300.0°K, the melting point of diphenyl ether. Heat input to the calorimeter caused isothermal melting of diphenyl ether, and the resulting increase in volume was measured by displacement of mercury from the calorimeter into a 200 cm horizontal, calibrated capillary, 1.25 * 0.01 mm diam, or into a weighed beaker. The advantages of diphenyl ether over water have been previously pointed out7 and include: i) an increase by a factor of 3.5 in sensitivity as measured by the ratio of the volume change to the enthalpy change on fusion, ii) the smaller required extrapolation from the melting point to the standard temperature of 298.17"K, and iii) the positive volume change on fusion of diphenyl ether in contrast to the contraction which occurs on fusion of ice. Diphenyl ether was purified by fractional crystallization to 99.95 mol pct as determined from the melting point depression with fraction crystallized. During assembly of the calorimeter, the ether was repeatedly outgassed under high vacuum to remove dissolved air. The calorimeter receiving vessel consisted of an 8-in.-long by 1:-in.-diam copper tube with twelve horizontal 3-in.-diam radiator "fins" for dissipating heat to the surrounding mantle of diphenyl ether. Before forming the mantle the chamber surrounding the receiving vessel contained 3300 cu cm of liquid diphenyl ether above 250 cu cm of mercury which was

Jan 1, 1970

By E. S. Anolick, Joseph Singer

The magnetic after-effect, in the form of time decay of permeability (l/µ), has been used to obtain independent data on the solubility of' carbon in pure iron. The results differ slightly from the solubilities obtained through internal -friction experiments. The mechanism of the time decay being the magnetic analogue of internal friction, it appears necessary to explain the observed discrepancies, and some suggestions are made. THE purpose of this work was to establish the reliability of the time decay of permeability as a measure of dissolved interstitial in the body-centered-cubic lattice, and further, to establish techniques suitable for such measurements with samples of a form convenient for various other measurements. This particular sample form was the "epstein" strip, i.e., 25 cm by 3 cm by 0.035 cms. While the general conclusions are not limited by this geometry, there are two aspects of the samples that may be relevant: a) texture, and b) grain size, which ranged generally from 1 to 10 mm. Effects due to these two possible parameters were thought to be small and were not investigated. Calibrating the time decay technique and the other experimental procedures by measuring the solubility of carbon in pure iron suggested itself because of the accumulation of data on this subject through the related technique of the internal friction'; The essentials of this report have been published in a somewhat condensed form.5 Since then some additional data have been taken. It is the purpose of this paper to add these data and to provide more complete description of the experimental techniques than was possible then. The time decay of permeability is a form of the magnetic after-effect.6,7 Permeability is measured immediately after demagnetization (µº) and also long after (µ8). The time decay, ?(l/µ), is the difference 1/µ8 - 1/µ0 and has been considered to be proportional to the concentration of a dissolved interstitial6,8,9,12 The relaxation time! 7, is characteristic of a particular diffusion, and affects the permeability as follows: where he being the activation energy for diffusion of the interstitial. Reference is made to the works of snoek6 and Neel7 for a complete discussion. A brief exposition of the principal ideas may be in order here, as follows. On the basis of the simplest model, resistance against domain wall motion increases with time after demagnetization due to the diffusion of interstitials to preferred sites created by the magnetostrictive tetragonolization under the strong magnetic field. Thus permeability, measured with a small field after the abrupt removal of the large field, will continuously fall with the process of diffusion of the interstitials, and the total "time decay" (or "time decrease") should be proportional to the amount of interstitial in solid solution. In the present report, use is made only of the total time decay rather than of the nature of the progress of the decay; the only problem involved in this approach is the need for assurance that only one interstitial is contributing to the effect as used. It is felt that the special use made here of the total time decay warrants the conclusions. Other work has been going on elsewhere on the detailed study of the nature of the time decay.8'9 EXPERIMENTAL A) Materials—12-lb ingots were made in a vacuum furnace from high-purity iron and by a series of hot and warm reductions were brought down to 14-mil strip. This was cut into 25-cm epsteins. The pure iron was decarburized at 750 °C by hydrogen. The time decay measurement for the decarburized iron (see below) indicated a satisfactorily low starting level of interstitials. Grain growth to grain sizes of 1 to 10 mm was produced in the pure iron by a 700" anneal in hydrogen after a critical reduction of about 7 pct as suggested by previous trials. No measurement of texture in the pure iron was made. The grain size was taken to be large enough to be beyond any sharply critical size regarding solubility. B) Infusion of Carbon—Since the permeability measurement required about two dozen epsteins, a special method of carbon infusion had to be developed to ensure homogeneity of infused carbon. This was accomplished by setting the samples edgewise in a

Jan 1, 1961

By N. J. Grant, D. S. Bloom

N recent reports, Sully' and Beck and coworkers' I have advanced hypotheses concerning the formation of the phase. Both of these hypotheses are based on Pauling's theories of the electronic configuration of the elements of the first transition group. Sully considered that the number of electrons which can be absorbed in filling electron "holes" is the factor which determines whether or not the structure can form. Beck suggested that the presence of a certain concentration of electron "holes" is the controlling value. It can be shown that a similar criterion can be developed without making reference to Pauling's theories. Table I shows the elements of the first transition group and the incidence of the a structure in the binary systems of these elements according to the data presently available. Also appended is the number of electrons considered to exist in the 3d-4s levels of these elements. If the atomic percentages for the phase are listed as shown in Table 11, and if the number of electrons in the 3d-4s levels per atom is calculated for the a boundary values, the results are as shown in the last column. It can be seen that the numerical values are all in the vicinity of 7 electrons per atom. This is true also for the ternary Cr-Mo-Ni IT phase, which occurs in a system in which none of the binary compositions are known to develop the phase. In the Fe-Mo binary, the high temperature a phase, which occurs at a composition of 50 atomic pct of each element, also yields a ,;1 e of 7 electrons per atom. From inspection of Tables I and 11, it develops that any series of sequential numbers which is assigned to the elements under consideration will result in the numbers pertaining to a compositions grouping themselves around one specific number. It does not follow, however, that this random number necessarily has physical significance. Such a point has already been discussed by Hume-Rothery." One interesting point develops from this study, however, and that is the position of manganese with reference to the other elements and to the phase. In the system used here, the formation of phase is associated approximately with the value of 7 electrons per atom, which is also the number of electrons per atom that manganese has. Manganese, it will be recalled, exists in three different crystal forms, none of which are the usual, simpler metallic forms; on the other hand, elements just to the left of manganese (in Table I) generally have lower coordination-number structures (body-centered cubic) than do elements to the right of manganese (face-centered cubic). The contribution to a complex crystal structure by the interalloying of elements from opposite sides of manganese is significant in that the a phase is formed in binary systems including one element from each side of manganese, with manganese capable of participating with both sides. It is indeed an interesting coincidence that manganese, with 7 electrons per atom, solidifies in complex crystal forms, and that when alloys of the transition elements are made which have seven 3d-4s electrons per atom, they, too, tend to assume a complex crystal form. From the above, it might be deduced that the study of the a phase might be advanced by a critical examination of the element manganese and how its structure is affected by small additions of elements which change the 3d-4s electrons per atom number. The role of atom size would also be of interest in formation. References ' A. H. Sully: The Sigma Phase in Binary Alloys of the Transition Elements. Journal Inst. Metals (1951) 80, Part 4, p. 173. 2 S. Rideout, W. D. Manly, E. L. Kamen, B. S. Lement, and P. A. Beck: Intermediate Phases in Ternary Alloy Systems of Transition Elements. Trans. AIME (1951) 191, p. 872; Journal of Metals (October 1951). "W. Hume-Rothery, H. M. Irving, and R. J. P. Williams: The Valencies of the Transition Elements in the Metallic State. Proc. Royal Soc. (September 1951) 208A. p. 431.

Jan 1, 1954

By W. O. Philbrook, R. S. Kaplan

Rates of oxidation were studied for levitation-melted samples of Fe-C, Fe-Si, Fe-C-Si, Fe-C-P, Fe-C-Mn, and Fe-C-S alloys oxidized by mixtures of either 5 or 10 pct O2, in helium at several temperatures in the range 1850o to 2050°C. The concentrations of the oxidized elements decreased linearly with time. Mass transport in the gas phase was found to be the rate-controlling step. Ilowever, a mulliple -film model was necessary to account for the flux of iron and manganese vapor counter to the oxygen flow. THE advent of the basic oxygen and spray-refining processes of steelmaking has generated considerable interest in the kinetics of reactions between oxygen-bearing gases and liquid iron alloys. The object of this research was the determination of the role of mass transport in the gas and metal phases and of surface chemical reactions in the overall oxidation process. Of the reactions for elimination of elements dissolved in liquid iron, the oxidation of carbon has been investigated most extensively. Studies by Fuji and Ura,1 Fuji,' and Gunji et a1.,3 done with pilot-scale basic oxygen furnaces, indicated that mass transport of gaseous oxygen was rate controlling when the metal carbon content was greater than 0.15 to 0.30 pct. When the carbon content was less than this critical amount, diffusion of carbon dissolved in the iron was thought to be rate limiting. L. A. Baker et a1.4,5 levitated samples of iron-carbon alloys and oxidized them in CO-CO2, CO-C02-He, and O2-He atmospheres at 1660°C. These investigators found that the metal carbon concentration decreased linearly with time and their samples exploded when the carbon content fell below about 0.8 pct. They concluded that the rate-limiting step was the transfer of oxidant to the gas-metal interface. A model based on this rate-limiting step predicted decarburization rates within a factor of two of those experimentally observed. The explosion of the samples was attributed to a shift in rate-controlling step from gas-phase mass transport to transport of carbon dissolved in the metal. L. A. Baker and R. G. ward6 and R. Baker7 used freely falling droplets to investigate oxidation kinetics. In both papers, the authors speculated that flame fronts may have been partially responsible for the lack of better agreement between experiment and theory. Swisher and Turkdogan8 oxidized liquid iron having an initial carbon content of 0.97 pct with CO-CO2 and CO-C02-Ar mixtures at 1580°C. They concluded that a surface reaction was the rate controlling step. Iron-silicon alloys have been oxidized by R. Baker7 and Filipov and Martynov.9 R. Baker 7 also studied iron-carbon-silicon alloys falling as liquid droplets through oxygen. He found that the rate of both carbon and silicon oxidation varied inversely with the drop radius. When the initial silicon concentration was greater than 6 pct, the samples cooled during their fall. Manganese oxidation has been studied by R. Baker,7 and by Filipov and Martynov.9 ward10 investigated the loss of manganese from liquid iron under vacuum. He found that mass transport of manganese vapor was rate limiting in argon atmospheres of 0.02 torr to 700 torr pressure. Iron-sulfur alloys were desulfurized with H2-He and H2-Ar mixtures by Peters et al.11 A model based on the transport of H2S from the gas-metal interface into the bulk gas gave fair agreement between the predictions of the model and the experimental results. EXPERIMENTAL TECHNIQUE Essentially, the technique consisted of using helium-oxygen gas mixtures to oxidize levitated samples of liquid binary and ternary iron-base alloys. The fused silica reaction tube is shown in Fig. 1. The coil design is similar to that of L. A. Baker et al.4'5 A Tef-lon-sheathed, ferritic stainless steel lifter (B) and an alumina pedestal (C) were used to support the sample in the coil prior to levitation and for the recovery of the sample. Samples were inserted into

Jan 1, 1970

By J. P. Morgan, J. R. Dawson

A review of Jones & Laughlin's Vesta coal preparation plant flowsheet in 1959 indicated that, of the three sizes making up the company's metallurgical product, the -48-mesh fraction offered the greatest potential for improvement. Efforts to improve quality and yield were directed toward the use of froth flotation. After laboratory and plant tests were completed, it was decided that treatment of the entire -@-mesh fraction of the coal mix by flotation was a significant step forward in providing better coal quality and recovery. Reduction of ash in the metallurgical coal from 6.75 to 6.25% provided material savings at the coal washer, coke plant and blast furnace. The Vesta preparation plant of the Jones & Laughlin Steel Corp. is located on the Monongahela River, eight miles south of Brownsville, Pa. This plant is capable of cleaning 2400 tph of a mixture of Pittsburgh seam high volatile coals from the Vesta and Shannopin mines to produce a metallurgical coal of 6.75% ash and a steam coal containing 14% ash. Heavy media vessels are utilized to upgrade the coarse coal while launders and tables handle the -1/4-in. fraction of the raw coal feed. Cleaned -1/4-in. coal goes to boot classifiers where the 48 mesh material settles and is removed by bucket elevators. This 1/4x48 mesh material is then sent to centrifugal dryers for dewatering. As designed, the -48 mesh fraction overflows the boot as a 7 to 8% solids slurry and is recovered by cyclones and a thickener and then dewatered by filtration. The products of the heavy media circuit, the launder-table-boot-dryer circuit and the cyclone-thickener-filter circuit, are combined to constitute the shipped metallurgical coal. The Vesta-Shannopin mix is combined at Jones & Laughlin's Pittsburgh and Aliquippa Works with purchased low and medium volatile coals for the production of metallurgical coke. A review of the preparation plant flowsheet in 1959 indicated that of the three sizes making up the metallurgical product, the -48-mesh fraction, containing 16.7% ash, offered the greatest potential for improvement of coal quality. This fraction was considered low, averaging 55%, while the rejects averaged only 33% ash. It was evident that while the boot overflow fraction represented only 6% of the product mix, a reduction in ash to 6 or 7% would reduce the ash of the metallurgical coal by 0.5%. The original plant flowsheet handling the boot overflow (Fig. 1) consisted of ten 14-in. cyclones treating 70% of the overflow and producing a 48x150-mesh underflow and a -150-mesh overflow. The cyclone overflow was combined with the remaining 30% of the boot overflow to constitute the feed to a 150-ft thickener. The cyclone underflow and the 48x325-mesh thickener underflow were fed to vacuum disk filters for dewatering prior to combination with the coarse metallurgical coal. The thickener overflow stream containing the -325-mesh material was split, 40% being recycled directly to the plant water system and 60% being flocculated and clarified in an 85-ft thickener. The underflow of this thickener was pumped to waste. Efforts to improve quality and yield on the -48-mesh coal were directed toward the use of froth flotation early in the investigation. A review of the fine coal flowsheet indicated that three streams should be considered for treatment by froth flotation. These were the -325-mesh thickener overflow, the -150-mesh cyclone overflow and the -48-mesh boot overflow. Flotation of the thickener overflow was considered basically to improve recovery by upgrading the reject stream so that it could be fed to the filters along with the thickener and cyclone underflows. The overflow from the thickener contained 3.7% solids and had an ash analysis of 33%. Flotation of the cyclone overflow and boot overflow were considered to upgrade coal quality as well as yield. Treatment of the cyclone overflow, a 5.4% solids slurry averaging 27% ash, would eliminate the coal thickener and provide a feed of flotation concentrate and cyclone underflow to the filters. Treatment of the boot overflow would eliminate both the cyclones and thickener and feed only flotation concentrates to the filters. Flotation feed in this

Jan 1, 1962

By W. D. Forgeng, P. F. Wieser

MnSi alloys containing from 2 to 24 at. pct Si have been investigated by metallographic and X-ray methods. Contrary to published data, the temperature of the ß-manganese to a-manganese transformation is lowered by the addition of silicon. The existence of two additional intermediate phases E and ( is demonstrated. E, ranging in composition from 12 to 15.5 at. pct Si, forms by a peritectoid reaction between ß manganese and the second new phase, (. The latter phase is homogeneous at silicon contents from 16.2 to 18 at. pct and forms peritectically from the 0 phase and liquid. The eutectic reaction occurs between the ( phase and MnsSi rather than the ß phase and Mn3Si. As a result of this investigation, a modification of the manganese-rich section of the MnSi equilihrium diagram is proposed. The binary diagram of Mn-Si, according to Hansen,' Fig. 1, exhibits in the low-silicon region (below 24 at. pct Si) a peritectic transformation at 900°C of 0 manganese + Mn3Si to a manganese as determined by R. Vogel and H. Bedarff2 as well as a thermal effect at 980°C between 16.2 and 22.6 at. pct Si reported by the same authors. The nature of the latter transformation was unknown. K. Amark, B. Boren, and A. westgren3 reported indications that possibly four more phases existed in the range of 10 to 27 at. pct Si. The present investigation deals with the phase relations in the range of 2.1 to 17.7 at. pct Si. A few spot checks were conducted up to 23.84 at. pct Si. EXPERIMENTAL PROCEDURE Small experimental heats were prepared by induction melting in a vacuum furnace using argon as a protective atmosphere. The crucible was of commercial-quality magnesia. The furnace charge consisted of silicon metal and dehydrogenated electrolytic manganese. The typical analysis for these materials is shown in Table I. The molten alloy was tapped into 2-in.-square, 7-in.-long ingots. After visual inspection, a small quantity of alloy in the middle portion of the ingot was separated for use in this investigation.MnSi alloys containing from 2 to 24 at. pct Si have been investigated by metallographic and X-ray methods. Contrary to published data, the temperature of the ß-manganese to a-manganese transformation is lowered by the addition of silicon. The existence of two additional intermediate phases E and ( is demonstrated. E, ranging in composition from 12 to 15.5 at. pct Si, forms by a peritectoid reaction between ß manganese and the second new phase, (. The latter phase is homogeneous at silicon contents from 16.2 to 18 at. pct and forms peritectically from the 0 phase and liquid. The eutectic reaction occurs between the ( phase and MnsSi rather than the ß phase and Mn3Si. As a result of this investigation, a modification of the manganese-rich section of the MnSi equilihrium diagram is proposed. The binary diagram of Mn-Si, according to Hansen,' Fig. 1, exhibits in the low-silicon region (below 24 at. pct Si) a peritectic transformation at 900°C of 0 manganese + Mn3Si to a manganese as determined by R. Vogel and H. Bedarff2 as well as a thermal effect at 980°C between 16.2 and 22.6 at. pct Si reported by the same authors. The nature of the latter transformation was unknown. K. Amark, B. Boren, and A. westgren3 reported indications that possibly four more phases existed in the range of 10 to 27 at. pct Si. The present investigation deals with the phase relations in the range of 2.1 to 17.7 at. pct Si. A few spot checks were conducted up to 23.84 at. pct Si. EXPERIMENTAL PROCEDURE Small experimental heats were prepared by induction melting in a vacuum furnace using argon as a protective atmosphere. The crucible was of commercial-quality magnesia. The furnace charge consisted of silicon metal and dehydrogenated electrolytic manganese. The typical analysis for these materials is shown in Table I. The molten alloy was tapped into 2-in.-square, 7-in.-long ingots. After visual inspection, a small quantity of alloy in the middle portion of the ingot was separated for use in this investigation.

Jan 1, 1964

By D. L. McDanels, J. W. Weeton, R. W. Jech

An investigation was conducted to determine the stress-strain behavior and tensile properties of metallic composites and to relate them to the properties of the base materials. Tungsten fibers in a copper matrix were chosen as the model sys-tem to investigate these properties. Room-temp-atzcre tensile and dynamic -modulus tests were used To meet the demand for improved structural materials, considerable effort is being directed toward the creation of composite materials. One such material under investigation is the fiber-reinforced composite, in which a ductile, relatively weak matrix is reinforced with high-strength fibers. Some work has been done on the reinforcement of metallic matrices with metallic fibers1"5 as well as with ceramic-whisker reinforcement. Summaries of much of this work have been published by Mach-lin7 and Baske~.' Work done at the Lewis Research Center of NASA-" has involved the making and testing of composites composed of a fiber, tungsten, and a matrix, copper, which were insoluble in each other. An equation was presented that showed the relation between the ultimate tensile strength of the composites and the strengths and relative volume percents of the components. This relation was verified experimentally for composites containing fibers extending the full length of the specimen as well as for composites reinforced with short-length or discontinuous fibers. Since the publication of the preliminary results,9'10 additional data have been obtained. This paper presents these data as well as analyses of the stress-strain behavior and the mechanics of deformation of uni-axially oriented, fiber-reinforced metallic composites, in which both components are mutually insoluble. EXPERIMENTAL PROCEDURE Composites were made with high-purity copper as the matrix and 3-, 5-, and 7-mil-diam tungsten wire as the reinforcing fiber. Some specimens were made in which the reinforcing fiber extended completely through the full length of the composite test section. The fibers were placed in ceramic to determine these properties. The composites were reinforced with either continuous or discontinuos tungsten fibers. The tensile properties and stress-strain behavior of composites reinforced with either type of reinforcement were similar, and in both cases the full strength of the fiber was utilized. tubes to insure axial orientation and infiltrated with copper at 2200°F for 1 hr. Composites were also made with short-length (3/8 in. long) 5-mil-diam tungsten fibers as discontinuous reinforcement and infiltrated under the same conditions. The reinforcing fibers in both cases were longitudinally oriented in the direction parallel to the tensile axis. Room-temperature tensile tests were conducted on the composites, stress-strain curves were obtained, and ultimate tensile strength and elongation were measured. Dynamic modulus of elasticity, based upon the resonant frequency induced in the flexural mode of vibration, was also determined for the composites and the components. A more detailed discussion of the experimental procedure employed in this investigation may be found in Ref. 11. RESULTS Room-temperature tensile tests were conducted on 3-, 5-, and 7-mil-diam tungsten wires which had been annealed for 1 hr at 2200°F and show the tensile strength of the wires to be 331,000, 327,000, and 290,000 psi, respectively. Since all the composites were infiltrated under these conditions, the strengths were considered to represent the strength of the fibers in the composites throughout this study. The average tensile strength of the annealed copper used as the matrix in this investigation was 27,800 psi. Results of room-temperature tensile tests on composites reinforced with 3-, 5-, or 7-mil-diam tungsten fibers are plotted as functions of composition in Fig. 1. These data represent previously reported datag,l0 as well as data more recently obtained. The line shown on each curve represents a prediction of tensile strength as a function of composition; the calculation of this line was explained in Refs. 9 and 10. A similar plot is presented in Fig. l(d) for composites reinforced with short-length, discontinuous 5-mil-diam tungsten fibers. Again, both the previously reported and the recent data are presented, and the line shown is identical to that shown for

Jan 1, 1965

By Y. Baskin

Solid-solubility relationships in the Pseudobinary systems UAS-UP, UAs-US. UAS-UC, aid UAs-UN were investigated. The first two systems exhibit complete mutual solubility, whereas the component compounds in the other two systenzs are immiscible. The above information, together with solid-solubility data joy six additional pseudobinary systems , were analyzed for compliance wilh the Hurrze-Rothery rules for rnetallic systems. The relative size difference of the component nonmetal atoms was found to be the dopainant jactor determining the extent of solid solubility between the NaC1-type uranium compounds. The anionic and covalent radii of the nonmetal atoms appear to be inadequate for these systems, but compuled radii based on rare earth compounds yield consistent results for the uranium compounds. THE actinide elements, like metallic elements of the transition and rare earth series, readily form binary compounds with nonmetallic elements of groups IV, V, and VI of the periodic table. Of particular importance are the NaC1-type equiatomic compounds with carbon, nitrogen, sulfur, phosphorus, and arsenic. The uranium members of this family of compounds have high melting points, are essentially stoichiometric, and exhibit various amounts of mutual solubility. Thus, they are of interest for investigating the factors governing the extent of solid solubility. Previous investigators have determined the solid-solubility limits in the pseudobinary systems between the compounds UC, UN, US, and UP. Anselin et a1 .' reported complete miscibility in the system UC-UN. Baskin and shalek 2 and Allbutt et a1.3 reported that UP and US exhibit complete mutual solubility. Shalek and white4 reported partial miscibility in the system US-UC. At 1800°C the maximum solubility of UC in US is 40 mol pct, but that of US in UC is 4 rnol pct. shalek5 found limited solubility in the system US-UN; the maximum solubility of UN in US is 11 rnol pct at 1800°C, while that of US in UN is only 0.3 mol pct. White and askin 6 found very limited miscibility in the system UP-UC at 1800°C. Approximately 7 mol pct UC is soluble in UP, but there is no solubility of UP in the monocarbide. Phase relations in the pseudo-binary system UN-UP were investigated by askin.' Approximately 0.7 mol pct UN is soluble in UP at 1800°C, while UP is immiscible in UN. The present study was carried out to explore the extent of terminal solubility in the systems UAs-UC, UAs-UN, UAs-US, and UAs-UP. This information, combined with existing data, provided a sufficient basis on which to determine the factors governing solid solubility in pseudobinary systems containing NaC1-type uranium conpounds. I) EXPERIMENTAL 1) Materials. The compounds UC and UN were obtained from the Kerr-McGee Corp. and United Nuclear Co., respectively. The US, UP, and UAs were synthesized by reacting finely divided uranium with H2 S, pH3, or AsH3 gas at low temperature (300° to 500°C), followed by homogenization in a vacuum at moderately high temperatures (1400° to 1700°c).8-10 The materials were essentially stoichiometric, with the exception of UC, which exhibited a C/U ratio of 1.05. Oxygen was the major contaminant in these compounds, ranging from 0.05 wt pct in US to 0.30 wt pct in UC, and it was generally combined with uranium to form UO2. The UO2 content in these materials was usually of the order of 1 wt pct, and did not exceed 2 wt pct. Furthermore, no evidence was found for a high-temperature reaction between uranium dioxide and any of the compounds. Chemical analyses of equilibrated compositions in the systems UAs-UP and UAs-US showed that the non-metal atom to uranium ratios averaged about 1.01, and that the oxygen contents ranged from 0.06 to 0.22 pct. However, the small deviations from stoichiome-try or the presence of minor oxygen impurities do not invalidate the conclusions to be drawn from this study. 2) Experimental Procedures. The component compounds in powdered from were blended in the desired proportions for 5 hr in the ball mill that consisted of stainless-steel balls in a plastic container. Chemical analyses indicated very little metallic pickup from the blending operation and virtually no increase in oxygen content. The pellets were pressed in a 0.270-in.-diam steel die under 40,000 psi pressure. One wt pct of stearic acid dissolved in CCl 4 served both as a binder and as a die lubricant. Chemical analyses revealed that the stearic acid left no carbon residue in the sintered samples. The pellets were sintered in vacuum in an unsealed tantalum crucible. The temperature, measured with a calibrated optical pyrometer, was maintained at 1800" + 30°C for 3 hr. This was sufficient time for attaining equilibrium as no change occurred in either the lattice parameters or the sharpness of the X-ray patterns when samples were annealed for longer periods of time. The pellets were cooled with the furnace. Debye-Scherrer powder patterns were taken at room temperature with a 114.59-mm-diam Norelco powder camera and CuKor radiation (CuGI = 1.5405A). Unit cell dimensions were determined from a Nelson-Riley extrapolation to the high-angle reflections. The values for were precise to k 0.001A. 11) RESULTS X-ray and met allographic investigation revealed that complete mutual solid solubility exists in the pseudobinary systems UAs-UP and UAs-US. The lattice parameter vs composition plots, Fig. 1, show a

Jan 1, 1968

By L. Adler

Two basic cases involved in the design of an opening in bedded rock are: 1) where the beds deflect from each other so as to be separated; and 2) where the beds deflect onto their lower neighbor, loading the latter while reducing their own load. Analysis of case 1 is relatively simple, while the interference of the original deflection curves in case 2 complicates analysis of the latter. Figures and formulae are presented for determination of interference loading in this situation. The design of an opening in bedded rock involves two basic alternatives.1'2 In one case the beds deflect away from each other, so as to be separated from their neighbors; in the other case the beds deflect onto their lower neighbor, loading it, while reducing their own load. This is shown in Fig. 1. The first case lends itself to a simple analysis, since the upper and lower boundaries of each beam remain a free surface. In the latter case, however, due to the interference of original deflection curves, the analysis is more complex. Earlier investigators of this interference problem solved it by making the tacit assumption that this type of loading was uniformly distributed along the beam's length. While there is no intuitive justification for this assumption, its use does lead to an approximate solution. Still, a more exact solution does not require this apparently unrealistic restriction. To achieve initial simplicity, the analysis will at first be limited to a two-bedded sequence, as in Fig. 2. Since both beams have identical end conditions and spans, the original deflections of their center lines are members of the same family of curves, as shown in Fig. 3. Therefore, if interference occurs at one point along their center lines, it will occur at every point. For convenience, the midspan point is that usually examined. Deflection at midspan for a uniformly loaded beam regardless of end conditions is: where c is a constant depending on end conditions; w is the body load and equals yh, lb per ft; y is the specific weight of rock, lb per ft'; L is the span, ft; E is Young's Modulus, lb per ft2; I is moment of inertia (for a rectangular section), I = bh3/12 = h3/12, (ft4); b is the width of beam and equals one; and h is the thickness of beam, ft; or 3U > yB an Substituting the appropriate values into Eq. lb, interference between the two beds can be predicted. Should it occur, the additional loads along the lower boundary of the upper bed and the upper boundary of the lower bed must be determined. From the principle of action and reaction, these added loads are known to be equal and opposite, as indicated in Fig. 4. Since the final deflection curves for both beds are identical (Fig. 3), their successive derivatives of y with respect tox must also be identical. That is:

Jan 1, 1961

NEW MEMBERS The following list comprises the names of those-persons who became members during the month of January, 1914. Members ADIASSEWICH, ALEXANDER, Dept. of Commerce & Industry, 11, Nadejdinskaia, St. Petersburg, Russia. BEARD, JOHN W., Mine Supt., Lane-Rincon Mines, Inca, Temascaltepec, Mex., Mexico; BORCHERDT, WALTER 0., Supt The Bertha Mineral Co., Austinville, Va BREWSTER, BURT B., Sales Engr., Sullivan Machinery Co., 1127 Central National Bank Bldg., St. Louis, Mo: CHASE, ROGER E., JR., Assayer 3906 No. Baltimore St., Tacoma, Wash. CULBERT, J. VICTOR 7S4 Wellington St., London, Ont., Canada; DICKINSON, ALBERT W., Supt. Of Mines Bevier, MO. DODSON, T. M Mores, Colliery, Schuylkill Co., Pa FORREST, CHARLES N., Chem. Engr Maurer, N. J.

Jan 2, 1914

By C. N. Kravig

STANDARD raises at Homestake are 150 ft long. Raises of more than 150 ft, driven with the use of a cage and hoist, are considered long raises- some have been driven more than 900 ft. Long raises have eliminated the need for access drifts on each level when transfer and ventilation raises are driven. These timbered cage raises, 7x9 ft in cross section, include a rock compartment and a combination cage, pipe, and manway compartment. To prevent excessive weight on the timbers, 10x10-in. bearing beams are cemented into hitches cut in the rock at 150-ft intervals. The beams also hold back timber movement caused by daily drawing of rock through the rock compartment.

Jan 6, 1957

Coal production during 1963 amounted to 446 mil- lion tons, an anticipated increase of about 6% over the 1962 production of 422 million tons. Electric consumption was 207 million tons, a continuation of its upward trend with an increase of about 7%. The metallurgical market consumed 77 million tons: the industrial market, 96 million tons; and the retail market, 26 million tons. Exports were 46 million tons. Modernization continues in the coal industry as it approaches the mid-1960's. The industry has shown a keen desire to explore and pursue new developments, new concepts and new managerial methods and techniques that have become so vital and important for industrial well-being.

Jan 2, 1964