Search Documents

By Steven J. Schatzel, Kayode M. Ajayi, Marcia M. Harris, Zoheir Khademian

Predicting rockmass permeability is critical in evaluating various engineering designs, including estimating gas inflow to a longwall mine in the case of a hypothetical breach in the gas well. This study conducted field permeability measurements to validate a geomechanical model capable of predicting rockmass permeability during longwall mining. A series of slug permeability tests were conducted in an active mine in Pennsylvania. A model of the mine was constructed in 3DEC numerical modeling software, and permeabilities were calculated. The modeling results agreed well with the pre- and post-mining permeability measurements, showing the applicability of this tool to evaluate gas well stability near mine workings.

Feb 1, 2024

By K. M. Kim

An analysis was conducted to determine the effects of blasting on slope stability and downstream comminution processes. To investigate these effects, the extent of blast-induced rock damage and the magnitude of induced stress were examined. This analysis showed that damage may extend up to 500 m (1 MPa, tensile strength) into the rock mass, a distance that is sufficient to have an impact on the pitscale slope over the long term. In addition, the damage zone was calculated using the assumption that compressive waves are the primary agent in microfracturing during blast fragmentation. The calculated damage zone — up to 2.2 m (43 MPa, rock mass compressive strength) — indicates that microfracturing can occur throughout 20-50% of the entire rock mass in the blasting area, depending on the blast geometry, burden and spacing. Finally, an economic analysis was conducted by comparing two assumed blasts in a copper mine. The change in energy required for crushing and grinding was demonstrated using Bond’s law after increasing the blast energy from 180 kcal/t to 350 kcal/t. A total cost saving of 13.3% ($9.4M) was achieved with the increase. However, the benefits of blast-induced microfracturing must be balanced against the potential impacts to slope stability to ensure safe conditions, a top priority in mining operations.

Jan 1, 2014

By R. Trueman, D. B. Tyler

Numerical modelling was used to determine the magnitude and direction of stresses around drives both adjacent to and distant from open stopes in the South Crofty tin mine. Modelling predicted that drives near the stopes are situated in a stress-relaxed zone. The peripheries of drives that are sited in solid rock away from the influence of stoping are in compression. Key-block modelling was used to determine the typical geometries of critical blocks and distinct element modelling was used to determine block stability. The conclusions derived from modelling fitted the observational data. This indicated that key-block theory is a valid tool for analysing the stability of roadways in the South Crofty mine. The support requirements for drives located next to stoped-out areas were formulated using a risk analysis approach to key-block formation. The results were compared with support guidelines derived using empirical design methods. Good agreement was obtained for the roofs of the drives but not for the sidewalls. The concept of a critical excavation width was formulated: once an excavation is larger than the critical size the length of rockbolts need not be increased as the excavtion dimensions increase. This may be the case in all rock mases.

Jan 4, 1993

By Wilson Blake

Increased application and interest in the use of microseismic monitoring to deal with ground control problems, Particularly those resulting in violent failures, has brought about the need for practical guidelines with respect to all phases of microseismic monitoring. This report presents the results of an 18-month effort to review the microseismic method and develop needed practical guidelines. Microseismic activity and properties of microseismic events are treated so that these parameters can be taken into account when developing monitoring equipment. Microseismic equipment is discussed to provide familiarization with the components of monitoring systems. Factors to be considered and procedures for developing a microseismic monitoring system are presented. Both physical and electrical considerations for the installation of a monitoring system are discussed in detail. The operation of a microseismic system including data analysis procedures is presented. Field examples to illustrate use of microseismic data in evaluating ground control problems are presented in a number of case histories.

Jan 1, 1982

By Peter B. Dowden, Robert A. Robinson

Boulders, frequently found in tunnels excavated through soils, can pose major problems for full face TBMs in terms of slowing or halting the tunnel advance, cutter damage, and abrasive wear. The paper aims to consider the problem as a whole, from the geological characteristics of boulder sites, to the appropriate physical design of theTBM, and its operation in boulder-laden soils. In addition, visualization of boulders and other subsurface obstructions by seismic methods and ground penetrating radar are reviewed. The paper will assist the construction planner in assessing the risks and preparing appropriate specifications.

Jan 1, 2001

Arsenic occurs naturally in rocks and soils, water, air, plants and animals. It can be further released into the environment through natural activities such as volcanic action, erosion of rocks and through human actions. Higher levels of arsenic tend to be found more in ground water sources than in surface water sources of drinking water. Compared to the rest of USA, western states have more systems with arsenic levels greater than 10 parts per billion (ppb). The US Environmental Protection Agency (EPA) has historically regulated arsenic in drinking water at 50 ppb, but the agency has lowered the maximum contaminant level (MCL) for arsenic to 10 ppb-to be in compliance by January 2006.This paper reviews briefly a) aqueous arsenic chemistry and removal mechanisms and b) the available treatment processes to attain the drinking water standard of 10 ppb by 2006. The combining of an appropriate removal method with an existing system depends on several factors such as nature of arsenic, the water source, existing plant equipment and processes site conditions etc. The paper also includes one or two case studies from the State of Arizona. Key words: Arsenic, Drinking water, Treatment Technologies

Jan 1, 2005

By Gene R. Reid

The contract objective is the development of an Automatic Fire Control System for Mobile Underground Metal Mining Equipment. The Phase I Report, which described the projected data handling plan, was published on July 24, 1975. The Phase II effort covered the period from July 24 through December 2 and accomplished the following objectives: ? Acquisition of data in accordance with the project data handling plan. Data were acquired through visits to twenty mine sites in ten states and Canada; visits to Bureau of Mines and MESA facilities; visits to mobile equipment manufacturers; and an extensive literature search. ? Analysis of accumulated data which provided the following specific types of design inputs: selection of the type of mobile underground equipment found to represent the greatest overall fire hazard; typical operating conditions for the vehicle; characteristics of the reported fire experiences; and performance, cost and maintenance factors affecting potential purchases of automatic fire control systems for underground mining equipment. ? Development of the AFCS design concept. Utilizing the data analysis results and considering the state-of-the-art of fire control system components, a recommended design concept was developed with particular emphasis placed on the need for a low cost and reliable system. Design trade-off studies are provided for the recommended system and for four alternate system concepts.

Jan 1, 1975

By K. H. Johnston

This guide was written to furnish the coal industry with a description of techniques, instruments, and clues on how to find abandoned oil and gas wells that have penetrated coal seams. The report includes specific information on searching techniques currently in use by several coal mining companies, gas-transmission companies, and waterflood operators, as well as information on State agencies responsible for the enforcement of laws and the preservation and distribution of data pertaining to the drilling, development, and abandonment of oil and gas wells. Comparative tests were performed with several commercial electronic metal detectors to determine the feasibility of using them to aid in the search for abandoned wells and to determine the instrument most suited for that particular use. The role of methane detectors to locate abandoned wells is described, including a case history. Tests were made to develop an efficient procedure to follow in systematically searching an area for metallic clues or hydrocarbon evidence to abandoned wells. The guide describes, in detail, a search sequence, including the collection of basic data, preparation of the selected area, and the physical search. Methods are given for evaluating the results.

Jan 1, 1973

By Thomas Domanski

Any type of deep excavation whether for Bored Piling, Diaphragm Walls or Contiguous Bored Piling Walls depends on forming a stable borehole with a defined cross-section to receive safely the permanent materials. In modern construction the excavation depth can reach well the range of 100 m and above. The diameters of the Piles reach often sizes of 2.5 m and bigger. Top casings in Bored Piles (Diaphragm Wall none) are rather short and stability below the casing, need to be secured by stabilization slurry. The boreholes need to be formed through a variety of different materials and stand open for an extended period. Without a safe stable borehole, it is impossible to produce quality products and work cost-efficient. The understanding and proper usage of a suitable slurry is a key element essential for the delivery of Foundation Elements with high quality and within a reasonable budget. The setting of mechanical and rheological parameters in specifications is necessary and helpful, but probably insufficient to embrace and control such a key element in the practical implementation of foundation construction. The proper selection, design, implementation and supervision of slurries on site requires both from Contractors and Engineers to understand how different slurries do function. Only with this knowledge the right decisions in slurry operations can be made. This talk is directed to give some help to both, Contractor’s and Engineer’s, in understanding how different type of slurries do work. (Which ones should be preferred in what kind of soils.) The better knowledge will help the Contractor to control cost and enhance production. The Engineer will be able to assist in arriving at the appropriate technical choices and include in the specifications.

Sep 1, 2022

By N. Waters

"Nickel saprolite ores are normally mined as feed to Fe-Ni smelters or Ni matte smelting operations. The smelting processes typically require high Ni cut-off grades of approximately 1.5 to 2.2% Ni, depending on the operation. These very high cut-off grades result in a significant portion of the saprolite profile being regarded as “waste” and hence having little to no value. The Starved Acid Leach Technology (SALT) was developed to recover nickel and cobalt from nickel saprolites and Caron plant residues. Relatively small amounts of acid are applied to ground saprolites or Caron residues in order to selectively leach nickel and cobalt. The leaching is performed atmospherically under low free acid conditions. Nickel and cobalt may be recovered from the leachate as a mixed hydroxide. The mixed hydroxide may be added directly to a saprolite smelting operation or refined separately. InCoR Technologies is advancing the application of SALT at a number of sites. Bench scale testing has provided a relationship between acid addition and nickel extraction in leaching. Conceptual engineering studies have been completed by SNC Lavalin. The simplicity of the SALT technology provides the benefits of low capital and operating cost and an expected rapid ramp up to full production.INTRODUCTION The recent history of hydrometallurgical nickel laterite treatment plants has demonstrated mixed financial and operational performance. Table 1 summarizes the next generation plants built after the financial and/or technical failure of the Bulong, Cawse and Murrin-Murrin plants in Australia. The Coral Bay plants (Line 1 and 2) stand out (and now Taganito) as relatively low capital cost, simple (no acid plant, production of mixed sulfide product), and modest in scale (10, 12 and 36 kt Ni/a). However, the other plants in the list (Ravensthorpe, Ramu, Goro and Ambatovy) are all characterized by financial and technical challenges. All plants have a very high capital cost ($67,000 to $120,000 USD/annual t of Ni production). Ravensthorpe was sold by BHP Billiton after a poor startup. Ramu has had a steady ramp up but only produces mixed hydroxide for refining by others. Goro has had an extended construction period (since 2001), is high cost and has been very slow to ramp up to design production rates. Ambatovy has had a steady ramp up."

Jan 1, 2017

By D Adhikary, M Khanal, B Poulsen, H Guo

During longwall mining, the ability to reliably estimate the height of longwall mining-induced fractures is critically important in order to effectively manage mining-induced water inflows and aquifer interference. The extent of mining-induced subsurface deformation, fracture, surface subsidence and aquifer interference is largely controlled by local lithological conditions, mining methods and mine layouts. Therefore for the purpose of quantifying mining impacts it is imperative to incorporate the local geology and mine plan parameters in a mine scale model. Two different numerical models based on 3D continuum (Finite Element Method) and 2D discrete (Discrete element method) domains, respectively, are developed to incorporate the mine site parameters of a study site in Australia. Both the models are calibrated and validated with measured mine data. The continuum numerical modelling method is used to investigate the change in permeability of the overburden strata due to underground extraction considering the full 3D nature of geology and mine layout. The discrete element modelling method is used to simulate the initiation and propagation of fractures, allowing the caving of overburden strata to be represented in a realistic manner, and the permeability enhancement of the strata overlying the goaf to be calculated from first principles. Permeability enhancement in the discrete element model is a direct function of the fractures induced in the deformation/caving process; fracture location, extent, aperture and connectedness. From the numerical modelling under the simulated condition for the mine studied here, it is predicted that the permeability of the caving zone from the goaf to five times the mining height increases by almost six orders of magnitude. In the fracture zone to approximately ten times the mining height, the change in permeability is predicted to be around two to three orders of magnitude. At the height of more than ten times the mining height the magnitude of permeability increased is predicted to be one to two orders of magnitude. CITATION:Khanal, M, Poulsen, B, Adhikary, D and Guo, H, 2018. Modelling of height of connective fractures during longwall mining, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 254–265 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Fred Tarquinio, Giovanni Bonita, Lars Wagner

"A new embassy for the Peoples Republic of China is under construction in Washington, DC. The 475,000 square feet (44,125 m2) structure has five levels below ground and four above, making it the largest embassy in Washington DC. A vertical soil nail wall was used as the primary support of excavation system for the project. The soil nail wall was irregularly shaped, benched in areas, and up to 98 feet (29.9 m) in height. The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. Design and construction challenges included soft soil conditions, inside wall corners, underground utilities, seismic impacts from blasting, and logistical and political factors. Overall, wall movements were lower than expected, with maximum horizontal movement less than 0.25% of the total height of the excavation. INTRODUCTIONThe proposed Embassy of the Peoples Republic of China in Washington, DC, will consist of about 475,000 ft2 (44,125 m2) of building space and contain up to four fl oor levels above ground and fi ve levels of basement (Figure 1). When completed, the building will be the largest embassy in Washington, DC. The architect for the project, Pei Partnership Architects, along with the world-renowned architect I.M. Pei, made effi cient use of the site by inserting the building into the existing slope. Consequently, excavations reach heights up to 98 feet (29.9 m) on the southern side of the property and 42 feet (12.8 m) on the northern side.The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. The location of the building relative to the property line called for tight excavation requirements, including precise wall positions and shotcrete tolerances. Design and construction challenges included soft soil conditions, inside wall corners, arched walls, underground utilities, seismic impacts from blasting, and logistical and political factors."

Jan 1, 2007

By R. K. Jonas

"Pressure leaching and pressure oxidation in autoclaves are important alternatives in the extractive processing of gold, copper and nickel ores. The application of advanced control to pressure leach and pressure oxidation autoclaves could achieve significant benefits as has been shown in alumina pressure leaching. This paper compares and contrasts alumina digestion autoclaves to other mining autoclaves with respect to advanced controls. The application of advanced control in alumina with over 30 units controlled worldwide, and its benefits will be reviewed. The design and potential benefits from advanced control for pressure oxidation and leaching will be presented.INTRODUCTIONIt is this author's position and the purpose of this paper to propose that advanced control could be effectively applied to autoclaves in the nickel, gold, and copper mining processes. This is based on the proven effectiveness of advanced control on autoclaves used in the alumina industry for pressure leaching of bauxite ores. Incremental, but significant increases in production could be realized by applying advanced control to autoclaves, as evidenced by the alumina industry, and this not being implemented in other autoclaves in the mining industry.In addition, today the mining industry is being challenged to improve their production methods. In some markets like nickel, there is pressure to improve productivity and reduce the cash cost per ton. While in other markets like copper and gold, demand is vigorous with favourable pricing, and there are advantages to increase production and productivity given limited plant capacity. Advanced control has proven its capability to improve mineral processing operations through increases in throughput, recovery, as well as reducing variability. In today's mines, autoclaves are being used to a much larger scale and with much larger importance, thus it would be beneficial to improve operational performance through the use of advanced control.Accordingly, it is the author supposition that an opportunity exists in the mining industry to use a proven advanced control technology to improve the operations and financial performance of mines using autoclaves."

Jan 1, 2012

By E A. Gunn, J Zhou

In this paper a project to develop a joint optimisation/simulation model for production planning in a mine-mill complex is presented. The system involves a mill receiving ore from a number of different locations, each with a unique mineral composition. The mill consists of several crushing and grinding circuits that function in series and parallel. Scheduling the flow of materials through the mill is complex due to constraints on throughput imposed by the millÆs design, the length of time material can be stockpiled on the surface, varying input mineral composition, and throughput targets for a range of output products.An optimisation model is used to create a set of campaigns (ore feed rates) over a given planning horizon under the assumption of deterministic mill throughput. A simulation model is used to evaluate the production plan under assumptions of stochastic machine failure and operational losses created by the need to cycle between input feeds. Campaign scheduling has two important implications for the simulation. First, during any campaign, multiple ore types may need to flow through the mill. However, the mill must be controlled to ensure that only one type of ore can be in a crusher, a grinder or a storage bin at any point in time. Second, as the mill switches from one campaign to another, the set of ores being processed may differ. Thus, the flow of ore through the equipment during a campaign changeover must be controlled to ensure that one or more of the ores from the current campaign can be completely eliminated before the ores from the new campaign are introduced.The simulation architecture employed for this project is Visual Basic for Applications (VBA) combined with MS-Excel as a user interface. A fixed step discrete event orientation is assumed as the simulation framework. A set of model constructs was built for the project with a specific Canadian milling operation in mind, but was designed to be representative of a broad class of milling operations. The constructs are implemented as class objects within the VBA structure, each with a number of properties and methods. The collection of VBA objects forms a composable modelling toolkit. These objects can be linked together by users, via MS-Excel, to represent a broad range of milling operations.

Sep 26, 2011

By S Hanke, J Burden, P Spies

The Waterview Connection will complete Auckland’s long-planned Western Ring Route, a 48 km north-south motorway alternative to State Highway 1 that bypasses the central city to the west. The project involves construction of 5 km of new motorway – half of it underground in tunnels – to connect the Southwestern (State Highway 20) and Northwestern (State Highway 16) motorways.The Western Ring Route will link the major population and industrial centres of Manukau, Auckland and North Shore to give the region the connected and resilient strategic road transport system it needs to underpin economic growth and sustainable development. It will also provide a direct motorway link between Auckland’s central business district (CBD) and international airport.The project involves construction of twin 2.4 km driven tunnels with an outside diameter of 14.41 m beneath residential suburbs, a major arterial road and a rail corridor. Enabling works began in January 2012 while tunnel construction using an earth pressure balance (EPB) tunnel boring machine (TBM) began in November 2013.This presentation introduces the Waterview Connection project, its role in the development of the Auckland motorway network, its procurement process, the alliance delivery model and an overview of the project’s design features and construction progress to date.Design and construction highlights of the presentation include the TBM start-up, turnaround and breakthrough arrangements as well as the experience gained during the first tunnelling drive. The presentation also covers an innovative process developed for invert construction behind the TBM that is independent of tunnel excavation.CITATION:Spies, P, Burden, J and Hanke, S, 2014. The Waterview Connection Project – progress to date, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 519–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J Bassan

The mining industry is faced with imperatives to improve worker safety and productivity, adapt to skills shortages, high worker turnover rates, and provide more effective maintenance to new and ever more complicated plant and equipment. While more effective use of data combined with advanced analytics offers opportunities for improvement, providing this information to the worker in the field, in real-time, has proven expensive, cumbersome and ineffective. New capabilities are now emerging which address some of the limitations experienced to date. Augmented reality (AR) provides a means to overlay interactive digital information on top of the physical world. Combining the latest visual display, mobile computing and ‘track and trace’ technologies, AR provides an experience similar to a heads-up display in a fighter jet through small, personnel devices, such as smart phones or wearable glasses. Applying AR would allow a mobile worker to ‘see’ all relevant information for a given task, in the context of their physical environment and at the time they require it. The technologies behind AR are rapidly maturing and becoming available at a price point that is viable for commercial applications. It is anticipated that AR will become ubiquitous at a consumer level within the next five years. The specific challenges faced by the mining industry make it an ideal early adopter of AR technologies. This paper examines a number of use-cases of how AR can be applied to the mining industry and the benefits that can be realised. The paper will identify areas of further work and viable opportunities for immediate adoption within the industry.

Nov 22, 2011

By Benjamín Cebrián, David Flores, María Rocha Gil

This document shows the evolution of drilling and blast digitization process, savings and trends in a mine, using new technologies that creates business opportunities and general improvement of D&B process.

Feb 1, 2020

By P. Arz

With a total of five basement levels, ground floor and a further six levels above grade, construction of the Kö-Galerie building, on the Königsallee, in the centre of Düsseldorf, was completed with all the difficulties which accompany property development today in the inner city. To meet the intermediate and final deadlines, ad­vanced building techniques were used. Notable among them are the top/down method for simultaneous construction upwards and downwards from an intermediate level, and the use of pre-fabricated composite columns in drilled shafts for the main load-bearing foundations as well as diaphragm walls designed as permanent structural wall of the basement.

Jan 1, 1989

By J J. McNee and, J Crusius, T F. Pedersen

The use of water covers is a globally-applied method for minimising acid rock drainage (ARD) and metal leaching. Although the subaqueous disposal of potentially acid-generating materials has been shown to effectively limit ARD, under certain scenarios, metal remobilisation can occur at circum-neutral pH. The following paper presents data from four case studies in which metal mobility from submerged mine waste resulted in degradation to water quality in the overlying water cover. Subcentimetre resolution profiling of dissolved constituents across the tailings-water interface (dialysis arrays), in conjunction with mineralogical information, were used to elucidate the controls governing metal mobility. The data illustrate four pathways of metal remobilisation, including: the release of zinc via the oxidative remineralisation of metal-rich organics at the tailings-water interface; enhanced remobilisation of arsenic as a result of anthropogenic eutrophication; the release of copper resulting from the pH-driven dissolution of treatment sludges; and the release of radium from uranium mill tailings due to the dissolution of radiobarite [(Ra,Ba)SO4] by sulfate-reducing bacteria. The results highlight the conclusion that the chemical stability of submerged tailings reflects both: the solid-phase characteristics of the tailings material; and the physical, chemical and biological characteristics of the depositional environment. In particular, the data illustrate that rigorous characterisation of both the waste solids and receiving environment must be performed in order to assess their compatibility. The results have relevance to the management of tailings repositories including constructed impoundments, pit lakes and natural lakes.

Jan 1, 2003

By E. C. Baker

The capital investment and operating costs of two methane-control systems used during longwall mining operations are compared in this Bureau of Mines report. Costs are given for a surface gob hole drainage system and an underground cross-measure borehole drainage system to control methane gas in gobs in four coal mining areas--central Pennsylvania, northern West Virginia, southern Virginia, and northern Alabama. Present-worth analysis is used to determine the more cost-effective alternative in each location. The alternatives have equal lives and provide the same service based on a minimum rate of return of 15 pet. In central Pennsylvania and northern West Virginia, the gob hole system is more cost effective than the cross-measure system, by 10 and 18 pet, respectively. In southern Virginia and northern Alabama, the cross-measure system is more cost effective, by 29 and 38 pet., respecitively. Costs for other locations must be developed on a case-by-case basis.

Jan 1, 1988