Search Documents

By R. Gray

"Experience from Australia has identified what is referred to as non-conventional surface subsidence behaviour. This occurs under irregular surface topography, resulting in valley closure, valley floor uplift or “upsidence”, and far-field horizontal movements – even occurring beyond conventional “angle of draw” limits. This paper discusses such behaviour recently observed in Pennsylvania and focuses on the 2005 case of Duke Lake Dam in Ryerson Station State Park. In July 2005, there was a significant increase in water leakage through a number of growing cracks in the dam leading to the dam being breached to avoid an uncontrolled failure. An underground longwall mine was located approximately 900ft to the north, mining at depths of 330 – 720ft. Investigations (including a subsequent ground movement monitoring program) found a range of evidence in the vicinity suggesting that valley closure and far-field horizontal movements may have occurred resulting from the adjacent mining. The paper discusses the phenomenon of non-conventional subsidence behaviour and the Ryerson State Park case study, including an assessment of mining, geology and subsidence impacts and suggested ground behavioural mechanisms. INTRODUCTION Non-Conventional Subsidence The conventional understanding of coal mine subsidence on which most current subsidence understanding and prediction techniques are based, includes the concept of angle of draw which effectively limits the lateral extent of subsidence effects and impacts. Within this zone – above and marginally beyond the boundary of mining – downward vertical subsidence is the dominant component, together with localised horizontal movements towards the mined region, with related tilts and strains. However, more recent experience from Australia over the last two or three decades has identified what is referred to as non-conventional surface subsidence behaviour. This is found to occur in areas of irregular surface topography or variable terrain, and is characterised by phenomena such as valley closure, valley floor uplift or upsidence, and far-field horizontal movements, all of which can occur beyond the conventional angle of draw limits. NSW Department of Planning (2008) defined the conditions for both conventional and non-conventional subsidence behaviour as follows: “The conventional or general model of surface subsidence, which finds worldwide acceptance, is based on assuming the following site conditions:"

Jan 1, 2015

By Ronald M. Hays

The Duluth Gabbro Complex in Northeastern Minnesota possibly contains a significant domestic copper resource and the nation's largest nickel resource. Exploration has discovered large low-grade copper-nickel (Cu-Ni) deposits between Hoyt Lakes and the Boundary Waters Canoe Area (BWCA). The mining and processing of Cu-Ni will have environmental, economic, and social impacts. The purpose of this study is to relate major environmental, economic, and social considerations to various aspects of Cu-Ni extraction. An open pit and two underground (block caving and open stoping with backfilling) models were developed to generate information on the impact of Cu-Ni extraction. Important considerations having environmental, economic, and social impacts (luring various aspects of Cu-Ni extraction are identified and defined. These aspects are exploration, development, mining, beneficiating, smelting, transportation, and termination of operations. Considerations are grouped into the general categories of site, industrial, energy, climatic, resource, water, air emission, waste disposal, employee, tax and royalty, transportation, and community considerations. Cu-Ni extraction in Northeastern Minnesota presents major environmental, economic, and social risks. Decisions are required on trade-offs between adverse and beneficial impacts. The approach used in this study assists in assessing environmental, economic, and social impacts. It will aid in the examination of potential and projected short-term and long-term advantages and disadvantages and will aid in the development of Minnesota's Cu-Ni resource for the maximum benefit to society.

Jan 1, 1974

Most new engineers in the mining industry do not realise the importance of legal obligations. During investigations the first question you are asked is: Do you have any proof or evidence? The smallest detail in an underground notebook or a diary entry is able to be used as your proof and/or evidence. The importance of a paper trail is often undervalued and overlooked when you first enter the industry. As a new engineer, all too often your legal obligations, including your duty of care are not given enough consideration. Whose job is it to inform you of what your legal obligations are and when do they end? Everyone has legal obligations at every level of the industry, from graduate to mine manager. The level of these responsibilities varies depending on the position that you hold. When you first start in the industry you need to understand what your responsibilities are and how you are expected to discharge them, whether they are memos, databases or senior sign-offs, etc. In order to fulfil your obligations you must first discharge your own obligation, which in turn discharges those of your department and ultimately those of the mine. As a graduate engineer in the mining industry what I have learnt about my own legal obligations has come directly from my own experience, which will form the basis of this paper.

Jan 1, 2007

By Dan Ifrim, Andre Solecki

Tunneling could be a major challenge to tunneling contractors as tunneling operations can be seriously affected by the Tunnel Boring Machine (TBM) performance. Specifying the appropriate TBM methodology, selection of systems and features, is critical for managing tunnel risks and contribute to successful tunneling project. The paper analyzes tunneling records from the recently completed City of Toronto’s Ashbridges Bay Treatment Outfall tunnel project and underlines the righteous selection of the TBM type and associated TBM systems in achieving good advance rates during tunnelling and managing project risks. The paper intends to draw attention of a few aspects of TBM technical specification importance and highlight the lessons learned from this process.

Jun 13, 2023

By Aaron Jones, Guy Reed, Russell Frith

"In 2017, one of the international authorities on coal bursts, Dr. Chris Mark, published a paper entitled “Coal Bursts that Occur during Development: A Rock Mechanics Enigma,” in which several relevant technical issues were identified, the most pertinent being:i.whilst development coal bursts are commonly associated with geological faults, understanding which specific faults result in burst-prone development mining conditions and why, remains undefined.ii.conventional wisdom in relation to strong roof and floor geology of the coal seam might be limiting, based on certain burst examples in Colorado.iii. development coal bursts can occur without the local ground stresses being substantially elevated from their in situ levels.This paper outlines what is considered to be a credible, first-principles, mechanistic explanation for these three current development coal burst conundrums by reference to early published coal testing work examining the significance of a lack of “constraint” to coal stability and an understanding of how very specific structural geology and other geological features can logically cause this to occur in situ, albeit on a statistically very rare basis. This basic model is examined by reference to published information pertaining to the development coal-burst that occurred at the Austar Coal Mine in New South Wales, Australia, in 2014 and from the Sunnyside District in Utah, USA.The “cause and effect” model for development coal bursts presented also offers a meaningful explanation for the statistical improbability for what are nonetheless potentially highly-destructive events, being able to explain the statistical rarity being just as important to the credibility of the model as explaining the local conditions associated with burst events.The model could also form the basis for a robust, risk-based approach utilising a “hierarchy of controls” to the operational management of the development coal burst threat. Specifically, these include the use of pre-mining predictions for likely burst-prone and non-burst-prone areas, the use of the mine layout to avoid or at least minimise mining within burst-prone areas if appropriate, and finally the development of an operational Trigger Action Response Plan that reduces the likelihood of inadvertent roadway development into a burst-prone area without suitable safety controls already being in place."

Jan 1, 2019

By L. J. Barnes, R. O. Koch, J. H. Versteegh, C. J. N. Buisman, P. J. H. Scheeren

Several water treatment options have been studied and piloted. A process based on activity of sulphate reducing bacteria combines sulphate removal and heavy metal removal in one process step. The anaerobic bacteria reduce the sulphate to sulphide and consequently metal sulphides will precipitate. The final design for the commercial scale plant is described.

Jan 12, 1992

By N. A. Eilertsen, Rolf S. Paine

The Bureau of Mines studied the presplitting technique used for controlling overbreakage in the walls of a vertical shaft at the U.S. Army Corps of Engineers Littleville Dam project near Huntington, Mass. The periphery of the shaft, the dimensions of which were 16-1/2 feet wide by 21 feet long and 52 feet deep, was presplit (cracked) in the solid to a depth of 48 feet prior to full-depth sinking. Presplitting prevented overbreak in a fairly soft schist and provided sound self-supporting walls which required very little scaling.

Jan 1, 1965

By E. P. Preis, R. C. W. Webber-Youngman

The real cost of any mining incident has, empirically, proven to be estimation-driven, rather than factdriven. One of the main reasons for this lies with the complexity of the cost composition of any given mining incident. Incident costs comprise both direct and indirect cost factors, and in many cases the costs associated with these factors are incurred during different time periods following the incident. In this paper we aim to identify the various cost factors arising from mining incidents, provide a thorough understanding of all the potential cost factors identified, and draw general conclusions on the knowledge obtained. Furthermore, recommendations are made on how mining companies could use the results, in order to assist them in calculating the costs of mining incidents. The paper also provides suggestions for further research, with the emphasis on the most significant immeasurable cost factors, namely the costs of implementing job accommodations following an incident, the harm to company reputation, and the decreased productivity due to low worker morale/psychological factors following an incident. If mining companies are aware of and understand which factors could contribute to the cost of any given incident, future planning and incident cost estimations could be easier. It should, however, be noted that although this study provides a comprehensive list of cost factors (and detailed explanations), other unknown cost factors relating to mine incidents could prevail in extreme cases.

Jan 1, 2021

By Casandra Gamez Gonzales, Angelina Anani

Copper, the newest addition to the critical mineral list, is an essential metal whose electrical and heat conductive properties label it as a vital mineral for the creation of renewable energy sources and the reduction of Greenhouse Gases (GHGs). However, despite copper’s leading role in the transition to sustainable energy and mining practices, the mining industry has faced various battles in the extraction of this valuable material. These challenges are based on mining’s negative reputation and extensive impact on the environment, nearby communities, and human rights. To ensure the survival of mining in the future and achieve mineral demands, an emerging topic that has initiated the revolution of the traditional sector into a more environment- friendly and transparent industry, is Environmental, Social, and corporate Governance (ESG). ESG has motivated companies to seek growth opportunities and standardize risk accountability and transparency based on its collective framework that creates, modifies, and implements local, national, and international standards. These standards focus on improving environmental, social, and governance issues faced by companies and their projects. ESG has served as a guideline that investors utilize to assess companies and promote sustainability, responsibility, and disclosure to create positive and balanced relationships with stakeholders and the environment. Nonetheless, concerns have been rising which state that ESG is negatively impacting the mining industry by targeting what fuels the industry and world: ore deposits and their resources. Therefore, this research focused on answering the following research questions: what are the impacts of ESG on the copper supply chain and how will stricter ESG standards affect future copper production?

Feb 1, 2024

By J. A. MacLellan

"CONSTRUCI'ION OF SHERRITT'S CONCENTRATORSSherritt Gordon is operating two mills north of the 56th parallel, and is presently engaged in building a third. The author was closely involved in the design and construction of all three of these concentrators.The Lynn mill is the oldest of these three concentrators-it is a 4,000 ton per day nickel-copper plant built in 1953. The Fox mill is a 3,000 ton per day copper-zinc concentrator built in 1970. The Ruttan mill will be a 10,000 ton per day copper-zinc plant scheduled to go on line in July 1973.LYNN MILL The Lynn mill including the crushing, concentrating, drying and load out plant is about 69,700 square feet or 17.4 square feet per ton per day. '!his plant was originally built in 1927 at Sherridon, 150 miles south of Lynn Lake, as a 2,000 ton per day copper-zinc plant. In 1952 the plant was moved by tractor train to Lynn Lake. The whole plant was re-oriented within the original perimeter walls as a 2,000 ton per day nickel-copper plant. This plant was expanded to 4,000 tons per day by the addition of t1-Jo rod mills and a 5-1/2 short head crusher in 1959.The Sherridon mill processed its last ore in Sherridon in September 1951 and the first load of nickel concentrate was loaded at Lynn Lake on November 9, 1953 when the railroad arrived at Lynn Lake.The site for the Lynn Lake mill was cleared of overburden in the summer of 1952 and foundations for structural steel and SO!l8 equipment foundations were poured the late summer and fall of 1952 • Steel was erected from January to June 1953. Most of the equipment came in from January to March of 1953 by tractor sleighs. Sane sleighs upset but no equipment was lest through the ice."

Jan 1, 1972

This Workshop was held at the Doubletree Inn, Seattle, Washington from September 26 to 28, 1997. Run under the auspices of the Deep Foundations Institute (DFI), it was co-funded by the newly formed Japanese Association of Micropiles (JAMP), and the Federal Highway Administration (FHWA). The Workshop was jointly organized and facilitated by Fujita Research Corporation and ECO Geosystems, Inc., with close support by Donald B. Murphy Contractors, Inc. DFI kindly consented to publish these Proceedings. As is clear from the list of attendees, 42 specially invited engineers from all aspects of micropile technology were present, representing Japanese, European and American practice. This proved to be a most friendly and interactive group of people, who freely exchanged ideas, views and close comradeship, not only during the technical sessions, but (and especially!) during the numerous social events. Perhaps the best illustration of this came in Day 2 when the attendees were divided into five competing teams, each comprising representatives from the different geographic groupings. These teams had to quickly devise solutions to two technical problems (using standard data previously provided. A team of "referees" (who also acted as "coaches") later determined the most apposite response, based on constructability design concept, cost, schedule and so on. Not only were the winning team very liberal in distributing the prize (vintage California champagne) among themselves, but the whole Workshop soon benefited from their generous division of the spoils of victory.

Jan 1, 1997

By Kyle R. Lackner, Jared P. Williams

"The Sutter Butte Flood Control Agency initiated the Feather River West Levee (FRWL) Program in 2010 to bring 35 miles of levee along the Feather River into compliance with applicable Federal and State standards for levees protecting urban areas. A combination of soil-bentonite cutoff walls, soil-cement-bentonite cutoff walls, and seepage berms will reduce flood risk by correcting under and through seepage deficiencies and remove more than 34,000 properties from the FEMA Special Flood Hazard Areas. The FRWL program includes a combined total of 7,744,803 square feet (SF) of cutoff wall planned to be constructed between 2013 and 2015. Cutoff wall construction methods to meet the design depths included conventional excavation to a depth of 85 feet and deep soil mixing for depths up to 120 feet. A key component of the FRWL program was the development of site specific mix designs using the design boring logs to evaluate the expected backfill gradation and permeability results. Issues that required a partnership between Contractors, Owner and Engineers included substantial Archaeological and Cultural Resource delays, significant depth changes due to a change in competent key, right of way acquisitions for abutting land, and the magnitude of the project in a resource limited industry.IntroductionThe Feather River watershed basin is located 50 miles north of Sacramento, CA and incorporates the agriculture producing communities of Yuba City, Live Oak, Gridley and Biggs. These communities are protected from flooding by levees that contain under-seepage and through-seepage deficiencies and were the cause of major failures in 1955, 1986 and 1997. The Feather River West Levee (FRWL) program was initiated by the Sutter Butte Flood Control Agency (SBFCA) in 2010. The long term objective of SBFCA is to correct the levee deficiencies and provide 200 year flood protection to more than 34,000 at risk properties located within the FEMA Special Flood Hazard Areas.Although FRWL contained a variety of construction components such as earthwork and pipe replacement, the slurry cutoff wall is the primary construction element for addressing under and through seepage deficiencies. From 2013 to 2015 approximately 6,649,210 SF of cutoff wall were installed using conventional excavation and deep soil mixing (DSM) techniques leaving 1,095,593 SF to be completed in 2016. The work was designed, solicited and constructed under two separate contracts, titled Project Area C and Project Area B&D. A summary of the contracts and cutoff wall quantities is presented in Table 1."

Jan 1, 2016

By R. T. Richins

Coeur d'Alene Mines Corporation (CDE) is a precious metals mining company. The company's three mining operations are located In Nevada and Idaho. Collectively, these mines (Rochester in Nevada, and the Galena and Coeur In Idaho) produced about 61,000 ounces of gold and more than 7.5 million ounces of silver in 1991. The company is currently planning the development of two major properties; the Fachinal gold-silver project in Chile and the Kensington gold project near Juneau, Alaska. Fachinal and Kensington hold encouraging potential to significantly expand CDE's gold production during this decade. The permitting process for these two distinctly contrasting environmental settings, project design requirements and regulatory/political circumstances provide the basis for a comparative analysis of licensing and permitting requirements, timeliness of the permitting process and costs in the U.S. and Chile.

Jan 1, 1993

By Edward S. Plotkin, Gary A. Almeraris, Thomas F. Peyton

The lining of the tunnel and shafts for a new section of New York City's- water system required extensive components to produce, deliver and place a continuous tunnel linning. The project placed approximately 153,000 CM (200,000 cy) of concrete for 5,340 M (17,520) of drill and blast 7.3 M (24 ft.) ID tunnel, located at depths of 152 M (500 ft.) to 213 M (700 ft.) . This section of tunnel will be connected to the surface water distribution system via four shafts of varying diameters ranging from 5.8 M (19 ft.) ID to 1.5 M (5 ft.) ID . All work was done beneath the streets of Manhattan under the rigid constraints of the City of New York and the Bureau of Water Supply regulations.

Jan 1, 1987

A recoverable uranium resource, shown to be suitable for in situ leaching, was discovered at Honeymoon in South Australia in 1971. Exploration of the deposit was carried out during the period from 1973 to 1979. Uranium mineralisation occurs in a coarse-grained unconsolidated sand aquifer located in the Yarramba Palaeochannel at a depth of approximately 110 m. Following initial development during 1979 to 1983 and the construction of demonstration leach facilities, the Project was put on hold. Southern Cross Resources purchased the Project in 1997. Government approval was received in March 1998 for the operation of on-site demonstration leach and recovery facilities while an Environmental Impact Statement was prepared and a 1000 tpa commercial production plant was designed. The Environmental Impact Statement (EIS) was released in June 2000 and operation of the test facility was completed in August 2000. Acceptance of the EIS by Commonwealth and South Australian state governments was announced on 20 November 2001. A Mining Lease was granted over the area of the proposed ISL operation on 8 February 2002. Operation of the Project is entirely dependent on using highly saline underground water resources to supply process and human needs. The management of discharge streams from the plant by re-injection was approved. The Honeymoon demonstration plant was the first adaptation of the solvent extraction process to highly saline in situ leach solutions. As such, it incorporated a number of unique operating and installation features. The trial period enabled optimisation of the process chemistry, additives and management and serves as an invaluable base for the proposed plant design and future operation. This paper discusses the nature of the uranium occurrence, the effect of saline water on the leach process and equipment, project design and environmental considerations, the requirements for disposal of discharge streams to minimise the impact on the arid environment and the requirements for rehabilitation following project completion.

Jan 1, 2002

By Melissa S. Beauregard, Randall A. Pietersen

This study focuses on quantifying the effects of water infiltration on a full-scale energy pile system’s ability to meet the thermal demand of an HVAC system. Theoretically, an energy pile system should increase its thermal capacity after a rain event due to increased moisture content creating an increase in thermal conductivity of the surrounding soil matrix. The United States Air Force Academy has an energy pile research site consisting of 8 full-scale energy piles located below a shower facility. The local colluvium surrounding the piles allows for relatively high water infiltration during rain events. This study uses an 11kW Precision Geothermal Geocube to apply a thermal load on two single-loop piles. A weather station located south of the structure records atmospheric conditions. Results indicate that moderate rain events can caused up to a 23% increase in the system’s thermal exchange capacity. This change is due to the increase in moisture content near the surface, which penetrates to deeper soil layers with time. The time required for moisture to penetrate to greater depths and then dissipate in the soil matrix, explains why increased system performance is seen for over a week following the passing of a singular rain event. 1 INTRODUCTION With a “future-forward” focus, there is an ever-pressing economic and environmental need to use sustainable sources to meet growing energy needs. HVAC is typically responsible for 34% of the overall energy required by commercial buildings and 48% of the energy required by residential buildings (USEIA, 2009; USEIA, 2012). Energy piles are a low cost, sustainable technology that have been used to offset this energy demand incurred by a building’s space heating and air conditioning requirements. An energy pile consists of heat exchanging elements in a closed loop system integrated into a building foundation and connected to a ground source heat pump (GSHP). It is most common for these heat- exchanging elements to be constructed within a drilled shaft foundation due to both construction practices and geometric considerations. This system operates based on the principle that at a certain depth below ground (typically 4 meters) subterranean temperature remains constant at a value equal to the mean annual air temperature at a given location (Kavanaugh et al., 1997). This allows the soil to function as a heat sink for cooling operations and a heat source for heating operations when exchanged within this zone of relatively constant temperature. For the past 25 years, the implementation of energy pile technology in public, residential, and even large-scale architectural complexes has slowly expanded which has created an increase in research into the topic as a result (Brandl, 2006; Hamada, 2007; Sekine et al., 2007; Gao, 2008; Bourne-Webb, 2009; Stewart and McCartney, 2013; Murphy et al., 2014). When pile construction takes place beneath the groundwater table, soil is under fully saturated conditions, maximizing thermal exchange for a GSHP system. Under unsaturated conditions, however, changing moisture contents change thermal conductivity values in a soil, which affect a GSHP system’s ability to meet a thermal demand. The observational data presented in this paper apply to GSHP systems in unsaturated soil conditions.

Jan 1, 2019

By D C. Verdon-Kidd, G R. Hancock, M J. Saynor, J B. C Lowry, T J. Coulthard

Designing post-mining landscapes requires quantifying the short and long-term risks. In recent years, computer based landscape evolution models (LEMs) have been used to provide insight into both erosion rates and processes (i.e. sheetwash, rill, gully erosion). An important requirement of these models is high quality model input parameter data, which includes both the surface material (i.e. soil and waste rock) and climate information. However, in many cases such data is limited and in the case of climate information, the data is often short and incomplete. Here we develop climate scenarios and examine different surface material properties using a case study at the ERA Ranger mine located in the Northern Territory, Australia Firstly we develop scenarios that represent the range of future climates that may be experienced at the site. Secondly we develop a series of plausible particle size distributions based on a large sampling exercise of the waste rock material. We then test the sensitivity of different rainfall sequences and surface materials on sediment output using a well-tested landscape evolution and sediment transport model (Hancock et al., 2017). CITATION:Hancock, G R, Verdon-Kidd, D C, Coulthard, T J, Lowry, J B C and Saynor, M J, 2018. Quantifying the effect of climate and surface materials on post-mining landscape erosion – a risk approach using landscape evolution models, in Proceedings Life-of-Mine 2018, pp 122–124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Ruth Escobar

Así como los seres vivos necesitan del oxígeno para vivir, las empresas mineras precisan de un modelo de innovación exitoso para ser competitivas hoy y en el futuro, esta es la síntesis del trabajo de investigación aplicada que la autora ha desarrollado durante 12 años de dedicada y satisfactoria labor, probando y perfeccionando un modelo de innovación minera denominado Innova, que se basa en la búsqueda de la adición de valor sostenible a una organización, desde la mejora continua de los procesos mineros a la creación de nuevas herramientas y métodos a partir del intraemprendimiento nacido del intelecto e ingenio de sus propios trabajadores a todo nivel.

Sep 30, 2022

By A. Renton Amell

The rate of dissolution of U02 was measured in acid solutions similar to those used for in situ leaching, with S04 of 10-1.82 to 10-4 M, Fe(III) of 10-2 to 10-4 M and pH's of 1.1 to 2.3. The dependence of dissolution rate on pH was small and inconsistent, probably reflecting the combined effects of a very weakly polar oxidizing complex, probably FeSO4+, and a nearly neutral U02 surface. Differences in the state of the U02 surface may explain this variability as well as contrasts between these results and results reported in other work. Changing either S04 or Fe(III) concentrations significantly affects dissolution rates. Increasing low sulfate concentrations in solutions containing 10 2 M Fe(III) at pH 2 results in formation of FeSO4+. In such solutions, rates increased with (S04)/(Fe(III)) up to 1:30, thereby indicating that the oxidation of U02 by FeSO4 is more rapid than by Fe3+. However, the dissolution rate decreased at higher (SO4)/ (Fe(III)), due either to sorption of SO42- on the UO2 surface or to formation of other less reactive sulfate complexes such as Fe(S04)2 or FeHSO4+ However, Fe(III) concentration is the dominant factor in determining solution rates. The rate was directly proportional to ferric iron concentration, indicating that the rate-determining step of the dissolution reaction is a single-electron oxidation by a ferric complex. Dissolution rates were lower in solutions of 0.1 and 1.0% H202 (0.029 and 0.29 M) than at similar concentrations of ferric iron because of formation of an insoluble surface coating of uranium peroxide, UO4?4H20. This phase may limit the value of hydrogen peroxide as an oxidant in lixiviants, not only by its very low solubility, but perhaps also by filling pores and reducing permeability in the ore body.

Jan 1, 1978

By A. L. de Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS). Biologically produced hydrogen sulfide has economically very interesting application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott's Bingham Canyon Utah copper mine a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE's Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998