Search Documents

By Joseph A. Mann

"Soil mixing is a proven solution for the construction of ground improvement adjacent to sensitive structures due to the use of computer controlled and monitored equipment. The precision to which geometry is controlled can often be the deciding factor for selection of soil mixing versus other means of ground improvement. Protection of existing structures and utilities requires careful planning, investigation, and may demand supplemental control measures. During planning, it is imperative that the process be fully developed by the project team to ensure proper control measures are budgeted; otherwise, the success and safety of a project can be jeopardized.This paper discusses case histories of soil mixing performed in close proximity to large, sensitive, and critical utilities, including foundation support for an existing earthen dam impounding a water reservoir in upstate NY, a buffer zone for a tunnel drop shaft at an operating wastewater treatment plant in Washington DC, and a containment system to protect a major water line along an interstate widening project in Baltimore, MD. The function of soil mixing as ground improvement varied; however, the selection and application of the technique versus other means of ground improvement was specific due to the controlled manner of construction with soil mixing. Through the three case studies, small diameter (3- ft [0.9 m]), large diameter (8-ft [2.4 m]), and mass mixing applications will be discussed. Furthermore, the case studies offer insight into how the geotechnical community in the Mid-Atlantic utilizes soil mixing technology for widely varying applications. Additional topics of discussion will be the design and construction of the ground improvement systems, procedures and execution of the work to protect existing structures, and the QA/QC methods, procedures, and results from the projects.INTRODUCTIONWet soil mixing, also known as the Deep Mixing Method, is a ground improvement technique that improves the characteristics of weak soils by mechanically mixing them with cementitious binder slurry. To construct columns, a powerful drill advances a mixing tool with radial mixing paddles located near the bottom of the drill string. The binder slurry is pumped through the drill string to the tool as it advances and additional soil mixing is achieved as the tool is withdrawn.Wet soil mixing is applicable in a wide range of soils. Soil mixing has been performed at depths more than 100 lf (30 m). Soils vary widely in their ability to be mixed, depending on the soil type, strength, water content, plasticity, stratigraphy, and texture. Almost any soil type, including organics, can be treated with certain soil mixing technologies, although they may require high binder contents and/or pretreatment to achieve the required results. In cases when the target soil is very soft, including some very weak clays and peats, 100% of the soil may require treatment. This complete coverage of soil mixing is referred to as mass mixing."

Jan 1, 2015

By Carlton M. Ray, William P. Levy, Thomas Lindberg

"The District of Columbia Water and Sewer Authority (DC Water) is implementing its $2.6 billion DC Clean Rivers Project to reduce combined sewer overflows to the District’s receiving waterbodies and mitigate chronic sewer flooding in District neighborhoods. The First Street Tunnel project is a major component of the DC Clean Rivers Project, designed to mitigate sewer flooding and basement backups in the District’s historic and densely populated Bloomingdale neighborhood. Bloomingdale has been historically affected by sewer flooding and was severely impacted by four storms in the summer of 2012 that caused significant damage to homes, the environment and public property. As a result, DC Water accelerated the design and construction of the First Street Tunnel in order to mitigate the effect storms have on the undersized sewers serving the neighborhood. The infrastructure designed to mitigate flooding, including the tunnel, are located within the highly urbanized neighborhood – with some structures being less than ten feet from residents front door steps. The success of a large public works project of this magnitude and in this unique location depends on a well informed and supportive public. With the local community impacted by flooding but concerned about heavy construction impacts, this paper details the components of a successful public outreach plan and lessons learned throughout the design and construction process. Early identification of community mitigation, working cooperatively with stakeholders and frequent dissemination of accurate information required the project team to establish a culture of problem solving collaboration with the community. BACKGROUND Chronic Flooding in the Northeast Boundary Sewershed The Northeast Boundary sewershed, in which the Bloomingdale neighborhood is located, is served primarily by a combined sewer system and has a long history of chronic flooding problems during moderate to severe storm events. The sewer system that serves the Northeast Boundary drainage area was constructed by the Federal Government in the late 1800's when developed areas of the District terminated at what is now Florida Avenue. Since construction of the system, population within the sewershed area has grown at an exponential rate. In meeting the growing needs of the population, the District experienced development that transformed previously low-density rural areas into new communities. Impervious areas have increased drastically since the sewer system was constructed and consequently, the existing sewer system does not have the capacity to convey storms with return frequencies beyond the 2-year storm without flooding. As a result of the capacity limitations, many of the low-lying areas have become chronic flooding areas due to the surcharging of sewers."

Jan 1, 2016

By O'Halloran. Gerard F.

"ECSTALL MINING has installed in their plants the most modern equipment in the mining industry. At the minesite, digital blocked frequency controls are used to monitor all crushers, conveyors, ventilation equipment and pumps from underground. Distant pumping stations are monitored and controlled by radio. Modern friction skip and cage hoisting systems have been installed with static power supply designed for automatic operation. Rotary-type compressors of recent design are in service in place of the conventional reciprocating-type units. At the concentrator, the 800- and 1500-hp synchronous motors driving the grinding mills have static field excitation and pneumatic clutches, still meeting modern-day concepts, having been• installed in 1966. The maintenance work load has increased annually for the past eight years. The modern plant, with all the present-day sophistication, must have a welltrained and well-organized force of skilled workers, and a maintenance system which will supply realistic facts and guidelines. This presentation will review the relative location of plants, utilities, maintenance and services, plant maintenance control and mechanical control. It is the hope that enough information will be presented to weigh the size of the job and how the resources are utilized for controlled maintenance."

Jan 1, 1974

By E.C. Jong

Resumen ¦ Un sistema de comunicaciones “a través del suelo” (TTE) comercial y disponible fue evaluado en una mina de carbón subterránea en la zona Este del Estado de Kentucky. Este estudio de campo fue realizado como parte de una evaluación multisitio mayor de sistemas TTE disponibles. La mina detallada en este estudio se encontraba paralizada al momento de la evaluación, lo que proporcionó la representación más cercana a la realidad del medio ambiente en una mina luego de una operación de cierre. Para este estudio se probaron las comunicaciones superficie a subterráneo y subterráneo a superficie. El despliegue estándar del sistema TTE usando los procedimientos recomendados por el fabricante logró obtener comunicaciones claras y nítidas entre el socavón y la superficie. Otras disposiciones de las unidades arrojaron resultados mixtos. Existen planes para examinar más los fenómenos observados en esta mina.

Apr 1, 2016

By Michael J. Beus, Jan G. Patricio

INTRODUCTION The U.S. Bureau of Mines, Spokane Mining Research Center, has been conducting and documenting rock mechanics research in the Coeur d’Alene mining district for the past ten years (1, 2, 3, 4, 14, 15). A current project combines the information gathered from rock mechanics instrumentation, geologic structure, and analytic techniques to improve shaft and support design for the deep mines of the district (3). This project required knowledge of the anticipated loads and the physical properties of the rock mass to provide accurate input data for computer design models. Several techniques have been utilized to determine the physical parameters including the USGS (U.S. Geological Survey) solid inclusion probe, the CSIR (Council for Scientific and Industrial Research) biaxial and triaxial strain cells, and the CSM (Colorado School of Mines) dilatometer. This paper describes the determination of the in situ modulus of deformation in three mines over a period of three years and the evaluation of these results as they applied to this project. The need for in-situ rock mass properties such as the modulus of deformation has stimulated research and development of a large number of instrumentation techniques. One area of continuing interest involves various methods of radial borehole dilation. This concept was pursued by Menard (9) with an apparatus known as the pressure meter, which is used frequently in soil mechanics. Other developments in rock mechanics include the CPC (cylindrical pressure cell) by Panek (11) and the dilatometer by Rocha et.al. (13) in Portugal. The CSM dilatometer, which also utilizes this technique, was chosen for this project because it required a small amount of background study, was inexpensive, and could easily be combined with other experiments being planned for the test locations. Although no previous field applications to hard rock (compressive strengths greater than 20,000 psi) has been documented, the instrument was selected since good results have been achieved in granite, oil shale, and several coal measure rocks (11, 12).

Jan 1, 1977

By Ronald H. Church

The Bureau of Mines tested & ground penetrating radar (GPR) system in the central Florida phosphate district. to determine the feasibility of utilizing GPR technology for subsurface cavity detection. The test area is located in karst topography where sinkhole development is prevalent. State regulations require subsurface drilling of damsites to identify underground anomalies; however, this method is not totally accurate in locating subsurface cavities that could lead to sinkhole development. An electromagnetic method of identifying anoma-lous subsurface conditions could reduce or eliminate the possibility of dam failure due to sinkhole development. The Bureau devised a GPR system that successfully penetrated over 50 ft of overburden and gave recognizable radar return signals characteristic of a rock-cavity interface.

Jan 1, 1986

By Y. Gordon

ABSTRACT A methodology based on a two-stage approach was developed for process technology selection. The first stage includes evaluation of available technologies, followed by shortlisting the best technologies based on mass and energy balance modelling, financial analysis, and risk analysis. The second stage involves detailed analysis using refined input data, mass and energy balance modelling, and capital and operating cost estimation, as well as a more detailed financial analysis. A case study covering the selection of ironmaking technologies for a company in the Russian Federation is presented to illustrate the critical elements of the methodology and the analysis process.

Jan 1, 2014

By R. J. Durrheim, B. Manzunzu, V. Midzi

Selecting ground motion prediction models (GMPM) is crucial in assessing seismic hazard levels in a specific region. This study investigates the influence of ground motion model (GMM) selection on seismic hazard assessment in Johannesburg, South Africa. Most seismic events affecting Johannesburg are related to mining activities and water ingress into the underground mine voids. The most seismically active regions in South Africa include areas around Klerksdorp, Welkom, and Carletonville. These regions experience a significant number of earthquakes, with mining activities being a major factor contributing to seismic events. Ten ground motion prediction equations were selected from regions of similar tectonics setting and were assessed to see if they correspond to the available local data. Six of these were also compared to the ground motions produced by the earthquake of 14 August 2014, which occurred in the Orkney area, one of the mining areas in South Africa. Sensitivity analyses were also carried out to assess the influence of ground motion prediction equations (GMPE) on the seismic hazard of Johannesburg. The results indicate that the choice of GMPM significantly affects the estimation of seismic hazard levels in Johannesburg. Different GMM can lead to varying ground shaking intensity predictions, impacting risk assessments and engineering design considerations. The findings highlight the importance of carefully selecting appropriate GMM tailored to Johannesburg’s specific geological and tectonic characteristics. Understanding how different models perform in this region is essential for accurate seismic risk mitigation strategies.

Jan 12, 2025

By Peter Zhang, Daniel Su, Essie Esterhuizen, Mark Van Dyke, Berk Tulu, Dave Gearhart

"Roof falls in longwall headgate can occur when weak roof and high horizontal stress are present. To prevent roof falls in the headgate under high horizontal stress, it is important to understand the ground response to high horizontal stress in the longwall headgate and the requirements for supplemental roof support. In this study, a longwall headgate under high horizontal stress was instrumented to monitor stress change in the pillars, deformations in the roof, and load in the cable bolts. The conditions in the headgate were monitored for about six months as the longwall face passed by the instrumented site. The roof behavior in the headgate near the face was carefully observed during longwall retreat. Numerical modeling was performed to correlate the modeling results with underground observation and instrumentation data and to quantify the effect of high horizontal stress on roof stability in the longwall headgate. This paper discusses roof support requirements in the longwall headgate under high horizontal stress in regard to the pattern of supplemental cable bolts and the critical locations where additional supplemental support is necessary.INTRODUCTIONLongwall mining is the primary underground coal mining method in the United States and currently accounts for more than 60% of the underground coal production. The longwall headgate, as a passageway for the longwall crew, intake air, material supplies, and coal belt transportation, is critical for both safety and continuous production of the longwall panel. A roof fall in the longwall headgate would not only result in substantial interruption of production but could potentially cause injuries or fatalities. Rehabilitation of failed roof in the headgate would also expose miners to the risk of injuries. Roof falls in the headgate, though infrequent, mostly occur in the belt entry near the face. Considerable research has been conducted to determine the effects of various factors on headgate roof stability, as well as effective measures to support the roof in longwall mines in the Pittsburgh seam (Mark, Mucho, and Dolinar, 1998; Chen et al., 1998; Su and Hasenfus, 1995; Su, Thomas, and Hasenfus, 1999; Su, Morris, and McCaffrey, 2002; Su, Draskovich, and Thomas, 2003; Hasenfus and Su, 2006; Van Dyke et al., 2015). Previous studies have demonstrated that high horizontal stress and transitional roof geology are primary factors that cause headgate roof failure. These studies also showed that panel orientation, retreat direction, pillar sizes, and roof support played an important role in the stability of a headgate.In underground coal mines located in the eastern United States, the magnitude of the maximum horizontal stress is typically three times greater than the vertical stress, and about 40% greater than the minimum horizontal stress. Mark, Mucho, and Dolinar (1998) studied seven cases of headgate failures caused by high horizontal stress in different coal seams in the United States and stated that roof stability is affected, to a large extent, by rock type, entry orientation, and longwall orientation. The effects of horizontal stress can be summarized in these statements: (1) A laminated roof is very vulnerable to high horizontal stress. (2) Entries that are aligned with the maximum horizontal stress will suffer less damage on development than those perpendicular to it. (3) Horizontal stress concentration and relief depends on panel orientation, the direction of retreat, and the sequence of longwall panel extraction."

Jan 1, 2018

By Robert Morgan

The mind-set that only blasters and their helpers need training in explosives can result in risk to other employees working at mine or construction sites where blasting is conducted. Misfires are not always immediately obvious during postblast examinations performed by the certified blaster in charge; the presence of undetonated explosives may not appear until well within the muckpile as was the case in the photo, right. To avoid accidents involving misfires, follow safety procedures specified in mine safety regulations, and the ISEE Blaster’s Handbook that include the following:

Jan 1, 2004

By G R. Ballantyne, A N. Mainza, M S. Powell, M Evertsson

Quantifying the performance of a comminution circuit relative to the potential that can be achieved is a standard requirement in justifying operating practice (the stick) and seeking operational upside (the carrot). Historic measures tend to focus on performance relative to laboratory design tests that provide a direct measure of specific grinding energy, such as the Bond Work index; or use dropweight breakage tests calibrated to a substantial database of operating sites, such as the SMC methodology. Although of value, such approaches are flawed in significant aspects. The assumption is that the laboratory prediction is correct and the single sample it is based on is representative. The database benchmarking methods are, by definition, locked into current average operating practice. These approaches do not illuminate upside; can ‘punish’ operations that are actually more efficient, such as grinding finer than standard operation; and reward poor operation that may comfortably produce a coarser grind than optimal for recovery or excess slimes that reduce recovery and increase water consumption and tailings volume. The authors present a set of established and easily applied measures, that draw together daily operation, highlight areas of opportunity and inefficiency, use simple samples and data, and can be used to provide the ‘size of the prize’ in pursuing specific areas of process improvement. These tools include size specific energy (SSE), overall operating effectiveness (OEE) which includes product quality, theory of constraints, and links this to the end objective – maximising the efficient production of valuable metals. Feeds into objective function driven by economics – financial return, energy, environment.

Aug 24, 2022

By Nathan P. Schmidt

Climate and hydrology data are required during all phases of mining projects, including impact assessment, mine planning and design, operational water management and mine closure and reclamation design. In the Canadian north, data sources are spatially sparse and often short-term in nature, and design parameters are often estimated based on data collected at sites far distant. Confidence in such data can be increased by verification or modification using data collected during properly implemented baseline and operational monitoring programs. A data set that accurately reflects conditions at the project is more readily accepted by regulatory agencies during the permitting process, and allows development of more effective and economic water management, mitigation measures and compensation. Data requirements and collection methods for developing an adequate data set for mine development are reviewed. These are illustrated using examples from oil sands, diamond and metal mines in the Canadian north.

May 1, 2004

By T. D. Moore

The use of a partially slotted 6.5-inch-inside-diameter vertical pipe to remove methane from a longwall gob area at a depth of 2,260 feet in the Pocahontas No. 3 coalbed was investigated. The value of gas removed by such a pipe under free-flow conditions was found to equal the cost of the installation in this case. Approximately 25 percent of the available methane passed through the pipe without the use of an exhauster; an additional 10 percent was removed when an exhauster was employed. The diversion of methane through a vertical slotted pipe to the surface permitted the use of increased mining rates and decreased the ventilation air requirements.

Jan 1, 1972

By Adam Stremcha, John MacGregor

Initial planning called for 3 separate drop shafts and 3 separate vent shafts to be pulled back from the excavated tunnel with a large diameter raise bore machine. With time constraints and the raise bore machine already in high demand on other shafts, a more “traditional” drill and blast approach was taken on a few of the larger drop shafts. This decision proved to be not only cost effective, but also reduced schedule impact as the shafts were excavated simultaneously with the other raise bores.

Jan 1, 2010

By Rob Boom, Yasuyuki Tozaki, Greg Traquair

The objectives of the business case are to examine a proposed metallurgical project and answer fundamental questions about project feasibility, risks, opportunities, and value. A business case fulfills these basic functions: estimates economic value; helps to understand competitiveness; serves as a risk management tool; and serves as a communication tool. A business case evolves with the project life cycle, and supports the gate reviews at the end of each phase of engineering, through to project construction and operations. A business case must be holistic, including all elements of scope that can impinge on project risk and value.

Jan 1, 2015

By S. M. Woodring

Research objectives included 1) determine relationships if any between spectral response of soil and soil textural groups, Unified Soil Classification subgroups and selected landforms and 2) develop computer assisted techniques for engineering soils mapping of remotely sensed data. The sire in northeastern Kansas, 1.6 Km by 43 Km (1.0 mi by 27 mi), contained glacial and alluvial soils. Multispectral scanner data (0.40 to 1.80 pm) collected at 915 meters altitude (3,000 feet) were analyzed using two distinct computer techniques: the nonsupervised approach involving delineation of soil training areas directly by computer and the supervised approach entailing training area selection manually by the researcher. Computer classification of surface materials follows both methods. Non supervised analysis results failed to show a consistant relation- ship between landform type and soil spectral class. Landforms correlating well displayed either unusually bright or unusually dark spectral signatures. Supervised analysis results showed a strong relationship between soil texture and soil spectral class. A moderately strong tie was shown between engineering soils groups (ML, CL, CH and OH) and their respective spectral classes, and a weak association between landform type and soil spectral class. An analysis procedure for engineering soils mapping by computer of remotely sensed data was developed. 1. Locate cultural features by visual examination of imagery. 2. Produce generalized bare soil-vegetation- water map using nonsupervised technique. 3. Outline significant soil fields for computer training using supervised approach. 4. Computer-classify entire area based on these soil fields.

Jan 1, 1974

Giant gold deposits are considered products of crustal-scale systems. Reduced fluids stored in mid to lower crustal reservoirs were discharged into mid to upper crustal sites of deposition. Elements of the architecture include crustal-scale structures, reduced packages of rock and regional seals. Gas-rich aqueous fluids were common but non-aqueous fluids may have been significant in the deeper parts of the systems. Fluid fluxes in over pressured domains were maintained by porosity waves. Abnormal heat input from the mantle may not be required once the systems were perturbed. Fluid-mixing and hypogene enrichment were probably the most significant precipitation processes.

Jan 1, 1999

By C. W. Smith

Research was conducted to evaluate the effectiveness of a well-point dewatering system in conjunction with a french drain to intercept waste impoundment leakage while reducing the volume of waste water requiring treatment. A well-point dewatering system composed of 585 production wells was installed around the perimeter of a leaking impoundment that previously used only a french-drain system for leakage control. The placement of the well-point system was designed to intercept and remove the leakage from the groundwater before the contaminant reached the french drain. Groundwater monitoring at this site revealed that after a period of approximately 40 days the well-point dewatering system had stabilized and effectively prevented the further spread of contamination to the french drain.

Jan 1, 2010

By P. Kim Carroll, D. Nick Tiffany, Doyl M. Fritz

Thunder Basin Coal Company received the 1987 Wyoming Excellence in Surface Mining Award for construction of the State's first major sediment control reservoir to be designed using the new settleable sol ids standard. Use of this standard resulted in construction cost savings of more than $250,000; reduced water quality monitoring; enhanced downstream channel stability because of more natural sediment loading; allowed simultaneous establishment of permanent waterfowl and fisheries habitat; and provided a quality recreational site. This article will address factors associated with the design and construction of that sediment reservoir and the benefits that were realized. (Note: This paper was originally published in the proceedings for the 1988 National Symposium on Mining, Hydro1ogy, Sedimentology and Reclamation held in Reno, Nevada, December 5-9, 1988.)

Jan 1, 1989

By Jeroen van Eldert, Daniel Johansson, Henrik Ittner, Håkan Schunnesson

"Numerous aspects of underground construction, from structural stability to construction costs, depended on the tunnel quality, including blast damage and the Excavation Damage Zone. Accurately quantifying the extent and severity of damaged rock is a problem. Recent technical developments in the field of Measurement While Drilling (MWD), including software for on-board logging and on-site analysis, have shown potential for rock-mass characterization. Ground Penetrating Radar (GPR) and P-wave velocity measurement have also improved and show similar potential. This paper explores the use of MWD, GPR and P-wave velocity measurements and uses them in techniques for excavation damage characterization and prediction. The paper is based on data collected from a small underground waste-collection site in central Stockholm, Sweden. The data is correlated against rock-mass characteristics and their responses are evaluated. Results indicate potential for excavation damage characterization for all tested techniques, which could minimize blasting damage and improve the over-all tunnel quality. 1 INTRODUCTION During underground excavation the rock mass is influenced in many ways. The Excavation Damage Zone (EDZ) is a result of these influences. The EDZ can be defined by an irreversible change in rock mass properties, for example increased permeability. EDZ is influenced by the excavation method, the rock mass properties and the in-situ stresses in the area of the tunneling. Since the 1990s research has been done on the EDZ by Emsley et al. (1997), Christiansson et al. (2005), Olsson et al. (2009), Ouchterlony et al. (2009), Ittner et al. (2014), and Siren et al. (2015). Based on past literature the EDZ have in this paper been separated in the following subzones: 1. Failure Zone or over-break is the area outside the planned tunnel profile, including the Look-Out and hole deviation. This zone consists of fracture networks (both natural and blasting-induced), that caused rock fall-outs. The extent of the over-break can be determined by volumetric scanning and photogrammetry and the half cast factor can be used as a damage indicator. 2. The Damaged Zone is split into three parts and but the quantity and depth of damage is difficult to measure. Although it can be visualized by sawing of rock slices in the tunnel wall (Olsson et al. 2009), diamond coring (DC) or P-wave velocity reduction (Jern 2001): a. Inner Damage Zone (Crush Zone): It is located directly around the drill hole, and is caused by the shock-wave energy of the detonation. The micro fractures in the Crush Zone produce a white-wash (rock dust) in the half cast. b. Transition Zone: This zone consists of micro fractures that connect and form macro fractures, both radially and parallel to the tunnel wall. The macro fractures are caused by the gas expansion during the detonation of the explosive; it increases the pressure in the (micro) fractures and creates the macro fractures. Seismic reflection, rock slicing and core drilling can be used for the examination. c. Progressing Zone: In this zone the existing radial fractures propagate due to the increase gas pressure inside these macro fractures. Examination methods are seismic reflection, rock slicing and core drilling. In addition, the Peak Particle Velocity (vibrations) could be used to estimate the depth (Tesarik et al. 2011)."

Jan 1, 2016