Search Documents

By Brian Isherwood, Tara Brown, Paul Kreycir, Jenny Earle

"The Shangri-La hotel and luxury condominium tower, recently opened on University Avenue in downtown Toronto, required eight levels of underground structure, four extending into the shale bedrock.Isherwood Geostructural Engineers was retained in 2007 by Anchor Shoring Limited to provide an alternative design-build solution to better address serious foundation risks. The site, bounded on three sides by City streets, abuts an existing 1957 14-storey building with five underground levels to the north. Sitting on the rock surface along the east perimeter under University Avenue runs the existing Toronto Transit Commission’s University Subway Line built by cut-and-cover in the 1950’s and which was believed to lie very near the property boundary at the southeast corner of the site.The bedrock under Toronto is known to contain very high locked-in horizontal stresses, much higher than can be resisted by shoring techniques, which result in inevitable wall movement when excavating deep into the rock. The strategy adopted to control the risk to the Subway, adjacent building, and major utilities is described in the paper, along with the comprehensive monitoring of movements, and their comparison to predictions.The ProjectThe 66-storey Shangri-La hotel and luxury condominium tower, recently constructed on University Avenue in downtown Toronto, houses 222 hotel rooms in floors 1-17; 287 residences on floors 18-49; and private estates including two 2-storey penthouses on floors 50-66. These comprise 873,000 square feet of development. Eight levels of underground basement are required to provide parking and other amenities, the lower four extending into the shale bedrock."

Jan 1, 2015

By T. J. Close

On September 10, 1991, Secretary of the Department of Interior Manuel Lujan deleted the Silver Peak Range North Wilderness Study Area from the list of U.S. Bureau of Land Management lands in Nevada to be considered for wilderness designation. This decision was based in part on the U.S. Bureau of Mines mineral investigation of the wilderness study area which found that it has indications of precious metals resources. The following is a summary of the results of that mineral investigation. The study area lies between the Silver Peak and Dyer mining districts of west-central Nevada. The Silver Peak mining district, to the east, has a long mining history dating back to 1907 when precious-metals-bearing veins were discovered. The major producer in the Silver Peak district was Sunshine Mining Company's Sixteen-to-One silver mine. During the Bureau's study the Sixteen-to-One mine was operating; it has since been idled due to low silver prices. Precious metals-bearing veins were discovered in the Dyer district, to the west of the study area, in the 1860's. Mineral activity in Dyer district consisted mainly of prospecting. The Silver Peak study area itself has no mining history and contains only a few mining claims, but the Bureau examined 13 mineralized sites, most previously unknown and unclaimed. These sites are along two zones that cross the study area from the Silver Peak to the Dyer mining district. The two zones transect a volcanic center of fractured and altered rocks that contain epithermal veins of quartz, calcite, and jasperoid with gold, silver, and base metals. At the surface these veins are poorly defined and poorly mineralized. The more than forty veins examined in the study area are as thick as 17 feet and as long as 1,000 feet. Samples from surface exposures of these veins contained as much as 0.02 ounce per ton gold, 2.1 ounces per ton silver, 1.0 percent copper, 2.6 percent lead, and 0.4 percent zinc. Analyses of the Bureau data disclosed no vein large enough or of high enough grade to be classified a mineral resource. However, most do have indications of silver-and gold-bearing resources at depth. Subsurface exploration had to be done on the vein at the Sixteen-to-One mine to outline reserves (a vein averaging about 22 feet thick and containing 6-to 7-ounces per ton silver); the same is true of veins in the Silver Peak Range North Wilderness Study Area.

Jan 1, 1993

By M Yahyaei, F Vos, J Siliezar

Site-based case studies (including data collected from industrial surveys) and their application in evaluating circuit performance, have a significant role in developing reliable process models. Such models are useful to both plant metallurgists and researchers. Appropriate process models enable the plant metallurgist to assess the impact of different operational parameters on the overall circuit performance. They also provide the researcher with a detailed understanding of process behaviour in response to changes in ore characteristics and process conditions (ie plant throughput, ore competence, ore type). Thus enabling the identification of effective operating factors, and allowing them to be ranked in order of their influence on the process response, which eventually develops into a process control tool in the hands of plant operators.The above approach has been developed and applied at the Julius Kruttschnitt Mineral Research Centre (JKMRC) separately for both comminution and flotation processes. In recent years, the JKMRC has attempted an integrated approach by developing process models that incorporate the impact of upstream processes on downstream processes. This is not possible using the traditional approach of separate comminution and flotation surveys, so conducting integrated plant surveys is crucial for success in developing integrated process models. This paper summarises industrial experience gained while conducting such an integrated plant survey at Glencore’s Ernest Henry Mining operation near Cloncurry in north Queensland. An appropriate approach should be taken to enable the alignment of different requirements from different processes during the plant survey. This, as well as the challenges faced in integrating comminution process models with flotation process models, are identified.CITATION:Yahyaei, M, Vos, F, Powell, M S, Siliezar, J and Perkins, T, 2014. Challenges in developing integrated process models based on industrial survey data, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 437–446 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By William Gleason

"Komatsu has been on the cutting edge of autonomous mining for the past 30 years and the company remains at the forefront of the technology that is changing from concept to a full-fledged reality.In 1996, Komatsu America Corp. (KAC) purchased a controlling interest in Modular Mining Systems; a move that enabled both companies to expand their product lines. It was through this effort that Modular helped to deploy the first autonomous haulage system (AHS) — the Komatsu FrontRunner system. In January 2008, the first commercial implementation of the FrontRunner system occurred at Codelco’s copper mine in Chile. Since then, Komatsu has put more than 130 haul trucks into seven sites on three continents to haul copper, iron ore and oil sands and its equipment has moved 1.8 Gt (2 billion st) of material with zero lost time incidents attributed to Komatsu’s autonomous trucks. The 1.8 Gt (2 billion st) is the most of any commercial mining autonomous haulage system and there is more to come. In November, Komatsu announced that an additional 150 autonomous haul trucks will be deployed to the Canadian oil sands over the next seven years.Komatsu has continued to pioneer autonomous haulage development, creating a range of autonomous options that includes semiautonomous and teleremote options all the way up to a haulage vehicle that stole the show at the world’s largest mining equipment trade show.In 2016, Komatsu advanced the concept of driverless haul truck to a new level when it displayed its Innovative Autonomous Haulage Vehicle (IAHV) at MINExpo in Las Vegas, NV. The concept vehicle is the first mega class haul truck designed to be fully autonomous, without an operators’ cab included on the vehicle.Unlike other haul trucks, the vehicle was developed exclusively as an unmanned vehicle designed to maximize the advantages of unmanned operation. Among other advancements, it was designed to distribute equal load to the four wheels, both when the vehicle is loaded and unloaded, and adopt four-wheel drive, retarder and steering. Komatsu said it is aiming for high-performance shuttling of this vehicle in both forward and reverse travel directions, thereby eliminating the need for K-turns at loading and unloading sites."

Dec 1, 2018

By N. T. Lowe

This Bureau of Mines publication presents salient deposit information in abstract form on 119 principal mineral deposits in the State of Nevada. Commodity coverage addresses 17 critical and strategic commodities that appear to have commercial production potential in the State. The core of the deposits described is taken from those properties evaluated d under the Bureau of Mines Minerals Availability Program (MAP); additional deposits are included to provide a more complete coverage. Institutional and infrastructural factors affecting mineral development are also discussed.

Jan 1, 1985

By F. F. Peng

Fine Coal Cleaning Processes including froth flotation, aggregative flotation or oil agglomeration, depend upon the wettability of coal particles in the aqueous solution. The wettability of coals of various ranks, hydrocarbon oil treated coals and oil-agglomerates have been measured using film flotation, induction timer, and froth flotation. Various hydrocarbon collector dispersion techniques are used to alter the surface wettability of coal particles. Change in wettability behaviors, measured by flotation responses, due to various ranks with or without of hydrocarbon collector modification are explained in terms of surface chemistry modifications as analyzed by induction time, film flotation as well as DRIFT Spectroscopy. The relationship between the wettability of coals and collector treated coals, and floatability are discussed.

Jan 1, 1993

Advanced process and equipment analytics have been around for a while. However, with accessible IT infrastructure and site maturity, it is possible to analyse, monitor, and control processing plants and equipment easily. These various disparate systems provide different reports requiring the involvement of various personnel and attention to different reporting platforms. For efficient harnessing of the systems? capabilities, as well as effective improvement and monitoring of process and equipment, a single point of entry is required. A process and equipment optimization solution was required at a concentrator in South Africa, focussing on the product stream of platinum group metal (PGM) concentrate from the UG2 Reef. The investigation of data to identify strategies for optimization was required to allow visibility into plant operations to guide operators, an easier method to identify process loop problems, identification of imminent equipment failures, and advanced process control to optimize throughput and stability. A collaborative effort between the client and General Electric Intelligent Platforms (GEIP) investigated data-driven solutions to each of the problems. With the focus on process optimization and asset monitoring, as well as equipment monitoring, a combination of approaches was utilized to address the various problem areas that were identified. Each was implemented separately in the control layer of the plant IT infrastructure. The integration was done in a centralized web-based reporting tool that integrated the detailed results from the various solutions. On the process control side, monitoring of control loops was included by calculating performance statistics that were reported daily to identify sub-optimally performing control loops and indicating potential problems. The advanced process control solution for this site includes a surge tank controller, stabilizing flow through the flotation banks, and preventing the surge tank from overflowing or running empty. Equipment monitoring was investigated, for preventative maintenance, by making use of statistical data models to indicate imminent equipment failure. These predicted alarm events included the cause for failure, drilling down, and allowing focus on a specific variable for preventative action. The results included a more stable flow through the mill, with fewer stoppages due to surge tank overflows or running empty. The causes for process drift could be identified and operators could react early. Alarms warning of equipment failure 2½ and 4 months in advance were identified in an offline analysis.

Jan 1, 2012

By A Hughes, J Agius, T Ferguson, A Parbhakar-Fox, D Lester, L M. Jackson

Management of historic tailings is a major challenge facing the mining industry and its regulators. However, through improved mineralogical and chemical characterisation of such materials the opportunity to develop better rehabilitation strategies arises. Microanalytical techniques including microscopy, mineral liberation analysis and laser ablation inductively coupled plasma mass spectrometry (ICPMS) allow for improved tailings characterisation – but the challenge posed by these techniques is how to use them effectively. Additionally, data sets collected by such techniques must be properly integrated, only then can they assist in the identification of the most appropriate rehabilitation strategies. A study conducted at the Old Tailings Dam (OTD) located at the Savage River Mine, Tasmania allowed for the integrated use of several microanalytical techniques to help evaluate the benefits of a shallow water cover as a potential rehabilitation strategy. Samples (n = 144) from 14 trenches and 11 boring cores (2 m maximum depth) were collected across the OTD. These were subjected to routine acid-base accounting, with a subset subjected to detailed mineralogy using a modified sulfide alteration index (SAI), X-ray diffractometry and mineral liberation analysis (MLA). In addition, representative samples (n = 6) from across the OTD were subjected to laser-ablation ICPMS to characterise the pyrite chemistry. Our results showed that tailings in the northern area submerged under a natural water cover were relatively unoxidised from approximately 1 m depth, with SAI values of 1 to 2. Tailings from the subaerial southern portion were extensively oxidised to approximately 35 cm depth (SAI = maximum 5.8), with fresher materials observed underneath (SAI = 5 to 5.8). Pyrite from across the OTD is enriched in Co, Cu and Ni. Through the integrated application of microanalytical tools, we determined that establishing a water cover of at least 1.5 m depth across the OTD is a suitable rehabilitation option for this historic site. However, consideration for the reprocessing of these tailings to extract Co should be further investigated.CITATION:Jackson, L M, Parbhakar-Fox, A, Hughes, A, Agius, J, Ferguson, T and Lester, D, 2015. Microanalytical evaluations of the savage river old tailings dam, north-?west Tasmania, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 111–124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D. W. Hayley

The rapid expansion of exploration drilling with anticipated production facilities for oil and gas in the Mackenzie Delta region of the Northwest Territories has created a demand for granular construction materials. This paper discusses the technique adopted and experience gained by the authors from several major resource evaluation programs in this remote area. The first part of the paper describes a methodology for deposit identification, logistics of helicopter and ground-based drilling operations and the sampling difficulties which are unique to permafrost: soils. The second part describes the exploitation of a large glaciofluvial deposit at YaYa Lake on Richards Island. Granular construction material is sparse in the delta region relative to projected demand. Exploitable sources of granular materials for aggregates or construction borrow are found in glaciofluvial deposits of Pleistocene age or in outcrops of Paleozoic bedrock. Glaciofluvial landforms can be located by reference to published surficial geology maps coupled with airphoto interpretation. Preliminary assessment of these features in a large region is most economically carried out during the summer months with a drill that is transportable by helicopter. Once prospective borrow pit sites are identified, a detailed ground-based winter drilling program must be undertaken to establish aggregate quality and quantity, and to provide information on natural features which could affect development. The glaciofluvial terrain has been highly modified by the formation of massive ground ice within the gravel deposits. This presents some unique pit development problems which are not encountered in a normal bedrock quarry operation.

Jan 1, 1977

By S. Chilka, I. Maloney, J. Brady

"The purpose of this project was to design the Electrical Service Platform (ESP) for the Cape Wind Offshore Wind Farm. The ESP structure comprises two primary parts: the topside platform housing the electrical equipment and the two jacket substructures providing foundation support to the platform. The topside is supported only by the two inner legs of each jacket. The site water depth is relatively shallow and the seabed comprised of loose sediment subject to severe local scour up to 18 feet. The piles are designed for local scour, storm conditions, vessel impact, ice loads and pile installation fatigue. This paper focuses on the design and construction aspect of this project.PROJECT DESCRIPTIONBackgroundThe Cape Wind project will be located in Nantucket Sound between Cape Cod on the Massachusetts mainland (northeastern coast of the USA) and the Islands of Martha’s Vineyard and Nantucket (Fig. 1). The project is to be sited on Horseshoe Shoal, about equal distances from the mainland and the two islands. The project will produce 75% of the electricity used on Cape Cod and the Islands of Martha’s Vineyard and Nantucket with zero pollution emissions and resulting in the reduced operations, fuel consumption and pollution emissions from the fossil fuel power plants in the region. The wind farm, if constructed per plan, is expected to be America’s first offshore wind farm.The wind farm will consist of an array of 130 Siemens 3.6-megawatt offshore wind turbines with a combined production capacity of 468-megawatts. The offshore wind turbine towers will be bolted onto the transition pieces supported by monopile foundations driven into seabed. The power from the 130 wind turbine generators will be delivered to the Electrical Service Platform (ESP) by an array of up to 14 seabed conductors."

Jan 1, 2017

By Pascal Deschamps

"INTRODUCTION During the last decades, many underground facilities for the storage of hydrocarbons have been excavated worldwide and the technology is fully mature. Similarly to other underground structures, the initial basic design has to be adapted along with the work progress, in order to cope with the actual site conditions and in particular the geology, hydrogeology and associated rockmass quality. In addition, Client’s or underground Contractor’s constraints (such as resources availability, schedule or cost impact) may vary from design to construction and require last minute adjustments. Engineers are required to introduce flexibility and anticipation of unexpected situations (similar to the above-mentioned) while conceiving large underground facilities. Although most of the cases require only minor adaptations, crucial parts of the facility have sometimes to be considerably modified and reviewed. This article will present four cases evidencing how the design of one of these essential structures - the concrete plug – has been adjusted during site implementation without impairing the initial performances. Hydrodynamic containment The product containment of the unlined caverns discussed here is ensured by the principle of hydrodynamic containment. A permanent water flow is naturally or artificially maintained with an orientation toward the storage cavern and then, neither product-tight membrane nor lining are required. The hydraulic gradient (and the associated water flow lines), being directed from the surrounding mass toward the cavern, prevent from outward migration of the product. If the hydraulic gradient is not sufficient or if the water table is evidencing instability, water can be artificially injected into the rockmass through purpose-built boreholes, drilled from dedicated galleries. This water injection system, called the water curtain, is generally located several tens of meters above the level of the cavern. This principle is illustrated here after."

Jan 1, 2016

A series of petrological studies were carried out on the characteristics of alteration and mineralisation in mainly structural-controlled (Deep Star, Meikle, Deep Post) and predominantly lithological-controlled (Post-Betze-Screamer and West Leeville) gold deposits in the northern district of the Carlin trend, Nevada. Alteration and mineralisation in these deposits are hosted in a sequence of calcareous clastic units of the Devonian Popovich Formation, into which have been emplaced a number of Jurassic intrusions, and syn- to post-mineral Eocene dikes. Four hydrothermal events have been recognised in these deposits: an initial Devonian base metal system and early diagenesis; a Mississippian stage of alteration in conjunction with burial metamorphism; contact and hydrothermal alteration and base metal-gold mineralisation associated with the emplacement of the Jurassic intrusions; and a Carlin-style gold system related to Eocene magmatism.

Jan 1, 2004

By Rong. G., T. Q. Lin, W. Du

Based on analysis of the evolutionary history of the valley in Baihetan, the mechanism of asymmetrical evolution, gradual migration-incision evolved from left bank to the right, is revealed in Baihetan river valleys. The process of in-situ stress evolution is carried out by using the Universal Distinct Element Code (UDEC). Consequently, the numerical results which indicate the main regulations of that stress field are as follow: (1) The phenomenon termed "high in-situ stress fold" appears in the bottom of the valley. With the maximum principal stress being 28-34 MPa, the stress increases significantly at a vertical depth of approximately 130 m. (2) The in-situ stress presents zonal distribution along the bank slope. It is apparent that the in-situ stress field consists of stress relaxation zone (SRZ), stress concentration zone (SCZ) and original stress zone (OSZ). The horizontal depth of stress relaxation zone varies from the left bank (roughly 200 m) to the right (about 120 m). Furthermore, the stress evolution of the left bank slope is studied. As a result, it is found that asymmetrical erosion contributes to the difference of the in-situ stress distribution as a critical factor, between the left bank and the right. And for an asymmetrical valley, the evolutionary process of in-situ stress field is a circular procedure, which includes the incision of valley, the accumulation of landslides and the migration of valley.

Jan 1, 2015

By M Brady

"It has long been recognised that the barometer infl uences areas of underground coal mines that havebeen sealed off from the current, or active, mine workings but it appears litt le formal research hasbeen done on how the barometer aff ects the goafstream sample point. Based on statistical analysis of samples from a number of mines from Queensland and New South Wales it can be concluded that there is a direct correlation between the barometer and oxygen concentration at a goafstream sample point. To help mitigate some of the high consequence hazards within the underground coal industry and protect the health and safety of the persons within that environment, many monitoring tools are utilised. A control recognised in management plans prescribed under New South Wales and Queensland legislation is the need to conduct monitoring to identify the early warning signs of spontaneous combustion. One of the monitoring tools utilised involves a bagsample being collected from a goafstream sample point then returned to the surface for analysis.When the sample is incorrectly collected, the resultant analysis from a gas chromatograph provides litt le value to the persons charged with the obligation of operating the coal mine at an acceptable level of risk. This, therefore, increases the probability of spontaneous combustion leading to a loss of equipment, mine and in the worst case, life. When the sample is collected correctly, the analysis presents early warning signs of low level oxidation allowing corrective action to be taken, to prevent the oxidation accelerating to spontaneous combustion. The eff ect the barometer has on this sample point should be recognised and the knowledge imparted to persons who conduct sampling to remove a variable in the bag sample collection process. This will ensure the persons operating the mine have a bett er understanding of what is happening within their longwall goaf."

Jun 1, 2012

By Y. Wang

Phosphates and fluorides are used as regulators for the removal of silicates from diasporic-bauxite both in direct and reverse flotation. While using dodecylamine chloride as a collector, micro-flotation studies showed that sodium hexametaphosphate has stronger depressing power on diaspore than on silicate minerals with increasing sodium hexametaphosphate concentration at pH 6.5, but sodium fluorosilicate shows poor depression on diaspore with increasing sodium fluorosilicate concentration at the same pH. Zeta potentials of diaspore and silicate minerals become more negative both in the presence of sodium hexametaphosphate and sodium fluorosilicate. Adsorption density studies indicated that the adsorption density of sodium hexametaphosphate on diaspore is much higher than that on silicate minerals at the concentration of 75 mg/L. FTIR spectroscopy studies show that sodium hexametaphosphate interacted with the Al atoms exposed on the diaspore and silicate minerals surfaces to form P?O?Al bonds through the P02 groups. It is possible that sodium fluorosilicate interacted through F- or [SiF6]2- with silicate minerals surfaces based on the analysis by AES.

Jan 1, 2006

By Riley S

Many regulatory bodies have, or are considering, guidelines that require rehabilitated mine spoils to be erosionally stable (satisfying quantitative limits) over specified design lifetimes. One of the problems facing the industry is that many of the computer models used for erosion assessment were developed for agricultural applications and are unable to predict the change in the shape of engineered landforms over extended periods of time. In particular, they cannot predict where valleys and gullies will develop in the landforms and how big or deep they will be. Furthermore, many existing models require considerable skill to use. A computer model (SIBERIA) developed by the first author, able to model this valley and gully development over long design lifetimes, and which is directly based on digital terrain maps is discussed here. Proposed rehabilitation strategies for waste rock dumps at Ranger Uranium Mine as assessed with SIBERIA are discussed. New features of SIBERIA of interest to the mining industry include the spatial distribution of erosion, deposition and gully development, and various measures of the quantitative risk of failure. A collaborative project with the Queensland Coal Association, involving the first author, aims to deliver these capabilities to the coal industry in a user-friendly package. The objective is the cost-effective rehabilitation of strip mines. Some preliminary results from this project are presented.

Jan 1, 1994

By Jared M. Green

This paper presents the wall stabilization design and implementation for a 541 linear ft masonry and concrete gravity-type retaining wall flanking the west perimeter of a 7.37 acre parcel in Bronx, New York. This paper will discuss the results of static and dynamic stability analyses performed for the pre- and post excavation phases for the proposed 300 ft wide open-cut of up to 14 ft of contaminated soil below the toe of the retaining wall. The wall stabilization consisted of over 74 inclined drilled and grouted anchor dowels, and 55 tiebacks drilled and grouted to the underlying mica schist bedrock. Three over-lapping rows of jet grout columns were chosen as the foundation solution for the existing retaining wall. This paper focuses on the design, construction and performance of the jet grout curtain wall. The jet grout wall served three purposes: 1) underpinning and excavation support for the removal of contaminated site soils, 2) permanent hydraulic barrier, and 3) resistance against a deep seated failure within the thick clay layer present at the site. The originally designed jet grout wall had unexpected negative effects to the existing retaining wall. The jet grouting program was modified while the Observational Method (Peck 1969) was employed to keep wall movements to a minimum. This paper discusses the diagnostic methods used to determine the cause of retaining wall movement; the implementation of a remedial ground improvement program; the modification to the jet grout installation procedure; and the ultimate performance of the jet grout wall.

Jan 1, 2011

By Louis E. Dalverny

U.S. Bureau of Mines research to develop diagnostic methods to locate and evaluate fires in abandoned mines and waste banks and techniques to extinguish such fires was applied to an abandoned 60-acre underground bituminous coal mine (Renton, Allegheny County, PA) to locate and extinguish three separated fire zones. Mine fire diagnostics interpret changes from baseline values in subsurface pressures, temperatures, and mine gas composition under imposed pressure gradients induced by a borehole exhaust fan. The effective gas sampling area surrounding each borehole is greatly enlarged. Sampling iterations, using a "communicating" boreholes set, provide "fire signature" information for locating both heated and cold areas. Time-dependent monitoring differentiates heating and cooling periods resulting from combustion front movement and/or fire extinguishment activities. A water injection with fume exhaustion extinguishment effort involved injecting water through boreholes to quench the heated zones while exhaust fans actively removed heated gases from the mine. The technique was ineffective as implemented, primarily because of inadequate spreading of water from the injection points. The Bureau's diagnostic method determined the fire locations and the effectiveness of the water injection with fume exhaustion extinguishment technique.

Jan 1, 2010

By Jeffrey M. Listak

The Bureau of Mines has conducted a rock mechanics study to monitor deformation of near-seam strata above a longwall panel in the Pittsburgh Coalbed. The primary goal was to determine the height of caving immediately behind advancing longwall face supports. This study, although site specific, provides information on the caving mechanism associated with longwall extractions so that strata behavior and its interaction with longwall face supports can be better understood. Two holes were drilled, approximately 550 ft apart along the center line of a longwall panel, from the surface to the coalbed approximately 650 ft below. Various downhole geotechnical instruments were used to monitor strata deformation. In addition, surface elevation surveys were conducted to differentiate between surface and subsurface activity. This report discusses the caving characteristics of the strata as the longwall panel approached and passed beneath the boreholes. Physical property data are also presented to demonstrate the relationship between caving behavior and local geology. Data show that immediate caving of strata above the longwall face occurred at a height less than 23.5 ft and that strata behavior above longwall extractions is highly dependent upon lithology, with major disturbances occurring at weak lithologic zones.

Jan 1, 1986

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber plant was recently completed at an existing facility, in order to treat the sulphur dioxide off-gas emitted from rotary kilns. Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong operational readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.INTRODUCTIONCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Quebec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary byproductof the process.Fresh hydrated lime and CDS residue is captured by the dust collection system and is re-circulated to the CDS via a fluidised transport system. Clean off-gas passes through the dust-collection system and is then sent to the atmosphere by a single exhaust fan.The CDS residue purged from the system is combined with the dust collected from the kiln offgas system and this mixture is wetted in the already exiting agglomeration system, to minimize dust generation during handling, and then sent to disposal."

Jan 1, 2016