Search Documents

By Steven D. Scott

Several polymetallic sulfide deposits (copper, zinc, f lead, silver, f gold) presently exposed at the surface of the ocean floor are of sufficient size and apparent grade that they will someday be seriously considered as mineable resources. Responsible ocean mining may have some real environmental advantages over land mining, although they both share the same downstream problems caused by smelting and refining. The area of disturbance for an ocean mine would be much less than for an equivalent sized deposit on land around which considerable rock has to be excavated in order to get at the ore. Acid mine drainage, a very serious problem in land ming, would not be a concern in the alkaline and oxygen deficient environment of the deep ocean. There would undoubtedly be loss of habitat for some marine organisms but this could be minimized by mining deposits that are no longer hydrothermally active and therefore support little life. The risk of severe corrosion and thermal damage to the mining equipment at hydrothermally active sites would probably preclude their recovery in any event. The scientific community and environmental advocates should take advantage of the long lead time before ocean mining commences to insure that the environmental mistakes of the past, as encountered in some land mining, are not repeated. In order to fully understand and thereby mitigate the consequences of recovering seafloor sulfides, test mining of a small deposit using the German-designed high capacity television grab, preceded and followed by detailed observations of the mining site from a submersible, is proposed.

Jan 1, 1992

By Gregory J. Kurras

In 1995 the Marine Minerals Technology Center (MMTC) of the University of Hawaii conducted a sidescan sonar survey and sampling expedition of the submarine geology and hydrothermal systems surrounding the active volcano White Island. The island is located in the Bay of Plenty, within the geothermally active Taupo Volcanic Zone off-shore of the North Island of New Zealand, and is the site of numerous shallow-water hydrothermal systems. The survey system, an EdgeTech DF1000 sonar, was a dual frequency 100 kHz & 500 kHz sonar capable of imaging the seafloor at better than 1 m resolution and possibly detecting gas bubbles within the water column. Sidescan imagery clearly shows sand channels, debris slumps, submarine landslides, and volcanic ridges all around the island to roughly 800 meters offshore. However, analyses of the both raw and processed acoustic data indicate that the sonar was not able to image any of the shallow-water hydrothermal gas seeps known to exist around the island. Vents were located using a commercial fish finder and knowledge from local tour guides and divers. Eleven gas samples from three different sites were collected by divers for analysis of chemical and isotopic composition. Rock samples were collected from thirteen underwater outcrops for correlation with existing data on subarial island flows sampled by previous investigators. Thin sections and XRF analysis were done for each rock to determine mineral assemblages along with major and trace elements, which were used to tie submarine samples to specific subarial stratigraphic layers.

Jan 1, 2011

By R. Mehta, M. Misra, X. Su

"The conventional methods to assess Acid Mine Drainage (AMD) potential of the waste rocks and tailings are based on wet chemistry and leachability tests. These methods are time consuming and expensive. There is a growing interest to develop alternate techniques to establish the reactivity of acid mine tailings and stability of treated waste forms. The Electrochemical Impedance Spectroscopy (EIS) is a reliable non-invasive technique which can be used for quick estimation of reactivity of the potential acid generating tailings. In this paper the utilization of the EIS technique for the estimation of reactivity of tailings is discussed. EIS can also be used to predict the long term stability of different stabilized waste forms.IntroductionMetal contaminated mine drainage is one of the most persistent environmental problems facing the mining and mineral processing industries today. Of all the mine drainage pollutants, acid mine drainage has become a substantial concern because of the potential long-term environmental implications and the accompanying liabilities. The main source of acid mine drainage is the tailings containing sulfide-ores which are generated during the ore processing. When these sulfide minerals, particularly pyrite and pyrrhotite, are exposed to oxygen and water they begin to oxidize. The initial chemical reactions produce acid and the acid dissolves heavy metals present in the tailings. Rainfall and snow-melt flush the toxic solutions from the waste sites into the downstream environment [1-2]. In addition to mining tailings, several Department of Energy (DOE) sites contain wastes which are contaminated with radionuclides and heavy metals."

Jan 1, 1999

By W. A. Grosh

The Bureau of Mines began a comprehensive investigation of the old lead diggings in the Wisconsin portion of the Upper Mississippi lead-zinc field in September 1947 to determine whether enough lead was present in shallow deposits to justify exploitation by modern open-pit methods. Because of the large number of areas of surface diggings, it was necessary to limit the investigation to only a few representative areas. Initial studies, therefore, included test pitting and hand auger-drill sampling at two sites n Grant County and one site in Lafayette County to determine whether further extensive sampling in that area was warranted. Results indicated that certain portions of the area contained substantial amounts of lead and, zinc; accordingly, more detailed sampling was undertaken, and the results will be described in a later report. Another phase of the general investigation was drilling and test pitting at the Nigger Jim Lafayette County. This 10 the third of the series and summarizes the work on the White property to develop the western extension of the Big Dick ere body, where four churn-drill holes totaling 679 feet were drilled. Inclusion of the White property in the study was justified because old reports indicated (1) production of ore from mines in the vicinity disclosed a high ratio of lead to zinc, (2) ore was present in the west heading of the Big Dick mine when it closed, and the attitude of the Big Dick ore body was such that a vertical hole would encounter ore that might be present.

Jan 1, 1950

By Robert G. Beverly

The presence of radioactivity in uranium mill wastes has resulted in somewhat unique waste disposal methods. In addition to the common problems of disposing of large quantities of solid wastes, neutralizing acids, minimizing dissolved heavy metals, and clarifying all liquid effluents, the uranium mill operator must sample and analyze liquid effluents for micro-micro quantities of radionuclides such as, radium-226, thorium-230 and lead-210. Special disposal methods or decontamination procedures are required to meet the stringent limitations established by the U. S. Atomic Energy Commission on the concentration of radionuclides in liquid effluents. Routine monitoring of the receiving stream is also normally required. In recent years there has been a growing concern about the radioactivity remaining in the uranium mill tailings, particularly at the sites of shut-down or dismantled mills. The State of Colorado, in cooperation with the industry, has adopted regulations for stabilization of inactive uranium mill tailings. The Mining and Metals Division of Union Carbide operates mills for the recovery of uranium and vanadium at Uravan and Rifle in Colorado and a mill in the Gas Hills of Wyoming for uranium production. The company also owns former mill sites on which mill tailings are located at Maybell, Rifle, and Slick Rock in Colorado and at Green River, Utah. The purpose of this paper is to describe the methods used by a few uranium mills, largely those operated by Union Carbide Corporation, to dispose of radioactive wastes, to discuss briefly the regulations under which the mills operate, and to present reference information on the subject.

Jan 1, 1968

By William R. Adamson

This paper describes some of the results of previously unpublished research studies conducted in underground operations in Chile and Australia, where cross-hole seismic measurement profiles were interpreted in terms of dynamic modulus. This work dates from a period between 1987 and 1990 and the Author suggests that 30 years on, applying modern day technology, instrumentation and modelling methods, more meaningful, practical and applicable results may be obtained.

Feb 1, 2020

By Maurice Guillaud

The most striking innovations on diaphragm-wall construction plant are those associated with continuous real-time trajectory monitoring of the excavating tool (either a grab or a hydro-cutter). The recent equipments are fitted with clinometers and gyrometers to control deflection, rotation or deviation from the vertical, thus allowing to install diaphragm-walls with a verticality accuracy of less than 0.3%. One of the greatest advantages of extensive use of on-board IT systems on the Hydrocutters and hydraulic grab machines is that it aids quality control by automatically producing complete real-time reports of all excavating data (verticality, depth, type of ground, rate of progress, stoppages, etc.). These reports are available to the Engineer, providing the total transparency required for Works Supervision and the Quality Assurance Plan. They also provide the Contractor with input data for databases used for optimising efficiency and progress criteria on future jobs.

Jan 1, 2002

By Mark Spence, Tom Lardner, Matthew Janes

"IntroductionThe design-build method streamlines project delivery through a single contract between the Contract manager and the design-build team. The design-build method places emphasis on collaborative project management between design and construction disciplines to minimize project schedule, reduce costs, encourage balance risk amongst the design-build team. Since 1985, the percentage of nonresidential design and construction projects has increased from 5% to 45%.1A project carried out in Edmonton, Alberta, Canada will be used as an example to illustrate the challenges of the design-build project delivery method and the merits of establishing a GBR. The project involved a complex slope stabilization as part of an extensive freeway widening. At the project location the roadway was being widened within the base of a historic stream valley into a steep slope with a history of a previous slope failure. The slope was to be steepened through the installation of a series of 14 interlocking arc structures constructed half way up the slope. Access and schedule proved critical to the successful completion of the project.Geotechnique and Site HistoryThe geotechnical investigation undertaken for the site included six boreholes drilled at the crest of the slope to depths ranging from 14.5 m to 30.2 m. Laboratory testing of the soil samples included direct shear tests, Atterberg limits and grain size analysis. The geotechnical report also referenced a previous geotechnical investigation that was carried out in response to a failure of the slope in 1971."

Jan 1, 2015

By Kevin Andrews, Zach Agioutantis

Analysis of Coal Pillar Stability (ACPS) software, released in 2018, integrates numerous empirical pillar design techniques. The ACPS program incorporates methodologies originally available as design tools from the National Institute for Occupational Safety & Health (NIOSH), including Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Analysis of Multiple Seam Stability (AMSS), and concepts including Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar formula, and pressure arch loading. The design methodologies that are the basis of ACPS were developed via analysis of significant amounts of real-world data and have been standards of the United States coal industry for decades. While there are empirical factors built into ACPS, making it ideal for use in U.S. coalfields, the concepts in the program have proven to be applicable in variable mine settings, and the software was developed to allow for user-based, site-specific modifications of key design inputs. Application of ACPS to cases outside the regions for which it was developed must be approached carefully, and continuous development of site-specific data is mandatory. A case study is presented involving the application of ACPS to assess pillar stability and assist future design for an underground lignite mine in Eastern Europe. Assessment of in-mine observations, review of the geology of the lignite mine, and evaluation of specific conditions associated with a failure event resulted in “calibration” of key input factors to ACPS. Scenarios evaluated with ACPS suggest that pillar strength and overburden depth are key factors for the determination of pillar stability and design in future areas.

Jun 25, 2024

Jan 1, 1991

By Errol D. Sehnke

This U.S. Bureau of Mines report provides detailed information on worldwide bauxite production capacity by mine and country, including bauxite substitute materials in countries of the former Soviet Union, The information was compiled from a variety of domestic and international sources and was based on information available to the Bureau through December 31, 1994. Capacity data represent announced installed and planned capacities and do not necessarily reflect a U.S. Bureau of Mines judgment of actual mine operating levels or timing of planned expansions. The year-end capacity is the ?in place? capacity or estimated production capacity, whichever is larger.

Jan 1, 1994

By W. E. Foreman

A mathematical model was developed to assess the costs for reclamation of surface mining using the shovel overcasting operation, the front end loader operation, and a backfilling operation. A literature review was made of the present laws in Kentucky, Pennsylvania, Virginia, and West Virginia pertaining to surface mining and of the various parameters that influence the input data for a mathematical model. It was determined that the working mathematical model would have to be applied on an area to area basis, preferably on a permit by permit basis in the area where surface mining was being done. To this end, a flexible model was developed with input data obtained from the area of study. The results of the study show that the cost per ton of coal for reclamation can be estimated for various reclamation levels. Validation of the model was done for selected permits from Virginia. It was determined that the permits could easily be used for input data to the model.

Jan 1, 1974

By Pamela Paradis-Sokoloski, Deni Thibodeau, J. Denis, Samantha J. Espley, P. O’Donnell

"During the previous decade, the role of spray-on liners within the mining industry was limited to providing a corrosion resistant coating to screen and bolts; however, increasingly, liners are being used as ground support products. Expanding use and testing of liners have demonstrated their ground support function, yet the definitive support mechanism is still under debate. The most promising theory is the retain/hold/reinforcement concept (Kaiser et al.,1992). This conceptual theory has been the basis for the recent underground trials at INCO where, specifically, shotcrete and MIROC Mineguard were tested in two trials to further define limitations and applications of each liner.In a cursory overview, shotcrete is becoming accepted as a support product, while Mineguard is only slowly gaining acceptance.This discrepancy is the result of the corresponding life-spans within the industry, whereby shotcrete has had wide-spread use for decades, yet Mineguard has only recently been introduced. Currently at INCO, shotcrete is primarily used: to provide support in poor ground conditions, to add stability when developing through backfill, and to provide damage control in seismically active mines. It is also used to protect production headings and secondary-blasting chambers from fly-rock damage during blasting. Despite an obvious support function of the liner, shotcrete has always been used in addition to bolts and screen. Comparatively, Mineguard is still in the testing stage, where the greatest potential is increased productivity for applications in multi-tasking development headings. In this scenario, Mineguard provides instant support to replace screen, and bolts temporarily. When the heading has advanced, the drill and support crews work in tandem, drilling off the next round and installing bolts for long-term radial support, respectively. Other potential applications of Mineguard are within production headings to replace screen in the back, and screen and bolts in walls. The potential for both liners to replace conventional support is clearly war-ranted, such that defining the support role was the primary goal of the two underground trials."

Jan 1, 1996

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By Ross T. McGillivray, David S. Graham, Dan A. Brown, Steven D. Dapp

"The Selmon Expressway includes an elevated structure extending across several miles of weathered karstic limestone geology, and represents a challenge for design because of the high variability of the material and the difficulty in characterizing the strength. The nature of the epikarst in this region of Tampa is such that variability can be extreme within distances of only a few feet. The weathered rock includes extremely soft soil infill within solution features on and within the formation. The limestone is so weathered that coring typically does not yield useful samples for strength testing, and in-situ Standard Penetration Testing (SPT) tests often encounter refusal blow counts. Thus the challenge for foundation design includes two components of reliability risks: the uncertainty associated with the ground conditions at a given foundation location plus the uncertainty associated with the foundation performance at a given location even when the stratigraphy is determined.This paper describes the design approach that has been implemented successfully for two projects at the Lee Roy Selmon Crosstown Expressway (LRS) in Tampa, Florida: the assessment and remediation of the reversible elevated lane (REL) foundations constructed in 2004, and the elevated expressways widening project constructed in 2012. Included in this design approach is a method developed for computing axial resistance in this local geology. Design for axial loading relies primarily on the development of side resistance, which was considered less subject to performance risks than base resistance. The calculation method incorporates a statistical analysis of SPT data, tempered by engineering judgment, to characterize stratigraphy at a given location into either soil, intermediate geomaterial (IGM) or rock.IntroductionThe subsurface stratigraphy of sites underlain by weathered limestone formations can be highly variable with respect to material layer thicknesses and strengths, even over short horizontal distances. This is the case for much of Florida, and particularly the Tampa area. These conditions present a challenging environment for the design of drilled foundations because of the need for a reliable determination of subsurface conditions at each foundation location, as they relate to the expected axial performance. Contributing factors include:"

Jan 1, 2015

By Bill Mariucci, Gary Almeraris

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2009

By J Young, S Yu, P Moyo, M Powell, A Musunuri, B Bonfils, S Kanchibotla, P Yaroshak, V Jokovic

The appropriate design of liners continues to be an issue on many mills worldwide. Loss of milling capacity especially at liner change, uneven wear lives along the mill, substantial scrap on worn liners, excess mill down-time, undesirably short and unreliable wear lives are all common issues. This paper presents a designed approach to liner optimisation that follows a logical path of initial design and step-wise improvements based on liner wear monitoring. The target is to have a good liner design from start-up, then tune the profiles, heights and thicknesses based on wear monitoring. This is conducted as a team of liner specialist, site personnel and liner supplier. The application to the Pustynnoye SAG mill of JSC Altynalmas in Kazakhstan is presented. The increase in liner life by around 50% along with increased mill throughput of over 20% illustrate the huge benefit of the cooperative triumvirate approach through the gains that can be made in productivity and reduced liner costs.CITATION:Powell, M, Kanchibotla, S, Jokovic, V, Hilden, M, Bonfils, B, Musunuri, A, Moyo, P, Yu, S, Young, J, Yaroshak, P, Yalcin, E and Gorain, B, 2018. Advanced mine to mill application at the Barrick Cortez mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 177–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By William Adamson

Precise and data driven methods of predicting and modelling blast induced vibration intensity are created and applied under field conditions on a routine basis today. These models are fed with controlled field measurements of vibration pulses generated by controlled charges under known geometric conditions. With such models blasting and geomechanical engineers can estimate vibration intensity at established critical points in mine bench geometry (surface mining) as well as within semi-permanent crown and rib pillars (in underground mining).Damage to bench walls and destabilization of large-scale geomechanical structures can be partially attributed to high intensity blast induced stresses on the rock mass and structures that define important features such as safety catch berms and haul roads. In the underground environment, weakening of critical pillars in block caving or Long Hole Open Stoping(LHOS) operations may lead to ore sterilisation. Blast vibration intensity can be linked with physical alteration in critical rock mass volumes within themine. Often the potential for vibration damage is estimated by the calculation of a critical value of vibration intensity, derived from a consideration of laboratory measured rock matrix properties. Efforts to confirm the accuracy of these estimates of critical vibration level include post blast excavation photography as well as the visual examination of rock mass, pre-and post-blast, using video camera observation of the walls of purpose drilled observation holes. These methods clearly indicate a change in fracture state due to the blast induced vibration, however further modelling of geomechanical stability will benefit if seismic measurement data can be interpreted in terms of geomechanically relevant strength parameters. This paper describes some of the results of previously unpublished research studies conducted in underground operations in Chile and Australia, where cross-hole seismic measurement profiles were interpreted in terms of dynamic modulus. This work dates from a period between 1987 and 1990 and the Author suggests that 30 years on, applying modern day technology, instrumentation and modelling methods, more meaningful, practical and applicable results may be obtained.

By E. Quaquero

This article reports on the current state of an ongoing research project which is aimed at implementing intelligent models for hardly predictable hazard scenarios identification in construction sites. As past evidences showed that no programmatic action can deal with the unpredictable nature of many risk dynamics, we tried to survey on how the current approach for safety management in the construction industry could be improved. In our previous research the use of Bayesian networks elicited from subjective knowledge were preliminarily tested. Those networks might be meant as a reliable knowledge map about accident dynamics and they showed that a relevant ratio of occurrences fall in ?hardly predictable hazards? class, which cannot be warded off by programmatic safety measures. This paper reports the second outcome of our research project, which focused on the development of first elementary fragments, regarding the occurrence of a possible ?hardly predictable scenario?. Instead of experts? contributions (who, over their carrier, seldom incurred in accidents), we used ?legal cases? as an accurate source of information. They suggested which categories of ?hidden hazard scenarios? are more likely to happen. We found that the most frequent hidden hazard scenarios are linked to operator?s negligence and abnormal behavior, e.g. irregular removal of scaffolding?s components, unprotected openings, improper use of PPE, etc. Every pattern determined by legal cases has been formalized by a fragment (i.e. elementary network) of the overall Bayesian network. Finally, all the elementary networks were integrated into a comprehensive intelligent tool for realtime hardly predictable hazards prevention. The final setup, asked for interfacing these intelligent models to a low-level sensor network and used to feed them with inputs about the current state of the context, is discussed too.

Aug 1, 2013

By David F. Gearhart

A cooperative study was conducted between Signal Peak Energy and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the behavior of a pre-driven recovery room under less than 200 ft of cover. The design of the support systems for a pre-driven recovery room must provide control of the roof and ribs during the changing stress environment experienced throughout the final advance of the longwall into the recovery room. It must also provide a stable area where mine personnel are not exposed to undue hazards during shield recovery operations. This recovery room was constructed in two phases; each phase mined a 21-ft-wide room that was heavily supported, and subsequently fully backfilled with 800-psi, cellular concrete. Instrumentation to monitor the recovery room performance included borehole pressure cells (BPCs) placed in the head gate and tailgate pillars, at four locations across the longwall panel, in the fill material, and in the first row of outby pillars near the center of the panel. Four roof-to-floor convergence sensors were installed in the back fill material and a vertical, multipoint borehole extensometer (MPBX) measured the displacement of the strata above the recovery room. Surface surveys were conducted to measure MPBX collar movement. The data show that the front abutment load was transferred onto the recovery room backfill and the out by pillars as the longwall panel was extracted. As the longwall approached the recovery area, the fender and shields yielded, but the backfill provided enough support to keep the room stable as the longwall advanced to its final position. The system worked as planned and the face was recovered in record time.

Jan 1, 2014