Search Documents

By H. Reginald Hardy

This report describes the results of a research project carried out to investigate the feasibility of using transducer arrays, located on surface or in shallow boreholes, above an active coal mine to detect and locate the source of underground microseismic activity which normally occurs during mining. The initial stage of the project involves the design and development of a self-contained mobile microseismic monitoring facility capable of use in remote field locations. Following this a variety of transducers, and transducer field installation techniques were investigated to obtain optimum sensitivity and high signal-to-noise characteristics. Preliminary efforts were also undertaken to develop semi-automated techniques for analysis of microseismic field data. Using the facilities and techniques developed field studies were carried out at a number of surface locations over a central Pennsylvania coal mine operating at depths of the order of 500 feet. In particular studies were con-ducted over a previously mined development area, troubled by extensive problems of roof instability, and over two longwall panels during mining. Although many of the field studies were carried out during the development stage of the project, results in general have been most encouraging. Limited results were obtained over the development area, however excellent microseismic signals, correlating with underground strata instability, were detected over both long-wall areas, proving the general feasibility of surface monitoring techniques. More recent studies, carried out as part of a subsequent project, and utilizing modified geophone installation techniques at a third longwall site, have verified explicitly the feasibility of measuring underground microseismic activity from surface locations. Sections of typical field data are included in this report along with a brief review of the studies carried out at each of the field sites. Detailed analysis of data obtained at the second and third longwall test sites will be presented in a later report.

Jan 1, 1974

By Todd Minoski, Matthew McElhinney, Mark Morris, Mark Mazzella, Joseph Bright, Morgan Sears, Craig Compton

To promote the safety and health of U.S. mineworkers, researchers with the National Institute for Occupational Safety and Health (NIOSH) are currently involved in gathering additional field data from the nation’s underground coal mines. The purpose of this field study was to monitor ground movement and changes in pressure during mining where conditions include a thick parting in the coal seam. To accomplish this, three arrays of field instrumentation were installed in the wraparound bleeder of a room-and-pillar panel at the Maple Eagle mine located in southern West Virginia. Borehole pressure cells (BPCs) were used to monitor the change in pressure in pillars located adjacent to the gob. Roof extensometers were installed to measure roof sag at various horizons in the immediate roof, while rib extensometers were installed to measure displacement of the in-seam parting as mining progressed. Additionally, visual observations and manual measurements were taken during subsequent site visits. The repeatability of results, important from a scientific perspective, was accomplished by successfully obtaining field measurements from two nearly identical instrumentation sites. The data collected indicated that the front abutment extent at the edge of the panel was approximately 200 ft, corresponding to a distance of 9– 10 times the square root of the depth. Yielding of the slabbed pillar began when the pillar line was approximately 290 ft outby the instrumentation sites. This was followed by load shedding onto the abutments and the measurement of small amounts of roof sag in the No. 1 entry. Instrumentation data, as presented in this paper, can be used to better understand stress redistribution, pillar performance, and roof/rib displacements. Additionally, this data is suitable for assisting in the calibration of numerical models. Insight gained from applying these models can be used to make better engineering-based judgments for conditions that could potentially be encountered in the future.

Jul 1, 2023

By Stephen Gale, David Clarry, Edmund Smith, Jon Feldman

"In 2006, a Canadian steel maker embarked on an ambitious initiative to become “Best in Class in Energy Management”. This initiative provides the framework for this paper, with some augmentation from other energy management projects carried out by Hatch. The initiative focused on identifying energy/GHG management improvements leading to low-cost implementation of energy savings or GHG emission reduction. The key components of the approach were:• Review site energy management practices and benchmark internationally.• Review best technical practices and benchmark against public energy intensity data.• Conducted a site-wide Energy Assessment and physical review of operating areas.• Facilitation of on site-workshops with staff to prioritize savings opportunities, as well as identify and remove implementation barriers.• Development of an Energy Management Action Plan for implementation of improvements.Most organizations can produce, with relative ease, a list of ideas for saving energy, implementing them is the challenge. This paper addresses these issues as well as the profitability of the energy efficiency improvements and the consequences for GHG emissions.IntroductionWhen one of the authors was an undergraduate engineering student at the University of Cape Town in South Africa, the technical drawing instructor made a statement that was both humorous, and mildly profound. He claimed that the most successful engineer is one who is both lazy and diligent. Lazy, in the sense that the engineer is constantly on the lookout for an easier, more efficient, way to do something. Diligent, in the sense that the engineer will work tirelessly to come up with a good technical solution for the easier way. This paper, somewhat of an anomaly in a compilation of technical proceedings, hopes to break the mould a little, and to show a “lazy-diligent” way of reducing the carbon emissions from an industrial facility, using a steel plant as an example."

Jan 1, 2008

Alluvial diamond deposits covered with a thick overburden cannot be explored effectively and mined profitably with the available conventional techniques. A novel directional drilling technique has been developed and site trials have been conducted at the De Beers Namaqualand Mines situated at the western coast of South Africa. This paper describes the technique developed as well as the results of the site trials. The main task of the project is to develop a tool and a supporting system to achieve a remote exploration and ore extraction method for inaccessible alluvial diamond deposits. The project involves the acquisition of a system, commissioning on-site and evaluating the information obtained during assessment. The project consists of the design -of certain tools and instrumentation for the system, investigations and desktop studies as well as development of the system's logistics. The operating philosophy of the system is based on the keyhole surgery principle. In this study a pilot hole was drilled first, starting from the surface with an inclination to reach deeply seated diamondiferous gravel layers, followed by drilling into a more or less horizontal gravel layer for a certain length and finally pointing-upwards reaching ground surface at a predetermined exit point. The pilot drill bit was then replaced with a larger diameter reamer/mining tool and an HDPE tail pipe was attached behind the reamer. The drill string was retracted back to enlarge the guide hole and flush the excavated ore to the surface through the tail pipe. The material flow in between the sections of the system was' carefully measured to assess and record the gravel recovery rates. Several horizontal holes were drilled at preplanned drill paths to reach and follow the ore layer and the Ore extraction was achieved by means of a reamer/mining tool. Principles of the concept have been proven viable in this investigation.

Jan 1, 2010

By Kozo Takeda, Arashi Shimano

"Dry Jet Mixing (DJM) method as the representative deep mixing technique has been demonstrating best practice on ground mitigation works coping with complicated soil condition and limited site space. This technique plays an important role in many projects to stabilize soft ground involving troubles like sliding failure, settlement, bearing capacity etc. Serious disasters caused larger earthquakes make great demand on the application of deep soil mixing these days. Special design and alignment of deep soil mixing has been established against to liquefaction and serious failure due to liquefaction. In this paper, representative example of liquefaction mitigation by DJM method is summarized. The paper also present result of surveillance of sites installed DJM col umns after attack by Tohoku Pacific Ocean Earthquake. Performance of DJM columns suffered the earthquake is demonstrated at several sites even with conventional column alignment.INTRODUCTIONThe DJM method is a representative deep soil mixing technique of dry mixing manner in Japan. DJM can successfully install soil mixing columns trough automatically controlled binder injection based on pneumatic feeding theory and cumulative experiences.This method was joint-developed in 1978 by private organization under initiative of the Public Works Research Institute of the Ministry of Construction as the optimum method for improving the Japanese soft ground. Figure 1 shows full view of the DJM construction system. Figure 2 illustrates DJM working system indicating Binder Feeding Plant side and Mixing Machine side respectively.As typical soil mitigation method, many projects related with rivers and roads and city development has required DJM technology. The total number of the projects applying DJM has exceeded 5,000 with the total treated soil volume more than 32,000,000 m3 by the end of fiscal year 2013."

Jan 1, 2015

By Jochen Maurer, Dr. Christian Hoyme, Dr. Hans Regler

Currently, it is very difficult to obtain qualitative and quantitative information about the status and production process of a construction site. As a rule, companies depend on reports from on-site experts. There is no end-to-end digitalization due to the mobility of equipment and ever-changing locations. Equipment from different manufacturers, especially in special foundation engineering, is highly specialized. Any data collected by this equipment is recorded in proprietary formats and made available on the manufacturers' platforms. This exacerbates the situation, making simple analysis of performance indicators impossible. Most functions such as construction diaries, equipment utilization analyses, etc. are implemented only as standalone solutions. This does not allow for prompt visualization and intervention in critical process sequences because the construction site process is usually managed using a cost-based method. Furthermore, special foundation engineering requires a high level of expertise in an extremely wide range of construction processes. In this article, the results from a set of non-proprietary performance analysis tools are presented using numerous practical examples. Once a construction element is completed, the equipment data is immediately transferred to the platform using the latest cloud technology. Because the data is normalized, construction progress can be documented immediately, even for mixed equipment fleets. Bottlenecks can be immediately detected by visualizing the current performance of the production process, which is broken down into individual steps. Modern analyses of this equipment data improve quality, thereby providing better information about current performance. These sets of tools are essential for changing from the current monetary or cost-based method of process management to time- and bottleneck-oriented management. This makes it much easier to identify the critical path during projects. The article shows that processes can be documented and managed.

By D. L. Moellenberg

Under various state laws enacted mostly within the last 20 years, reclamation requirements and standards for hard-rock mining operations have been established virtually everywhere in the western United States. Unlike the uniform and detailed coal mine reclamation requirements under the federal Surface Mining Control and Reclamation Act ( "SMCRA" ) and state programs mode led after SMCRA, the various state law hard-rock mine reclamation requirements are based upon a variety of objectives, and therefore are subject to varying standards from state to state. While the diversity of reclamation requirements complicates the determination of what reclamation measures will be required at any particular mine, there are valid reasons for this diversity. There are dozens of different commodities mined in the United States, and mining methods are different for each commodity. Local natural conditions such as climate, precipitation, geology, hydrology, and biology vary widely across the county. Site-specific conditions also affect mining and reclamation methods. Also, factors such as economics, land use, and environmental protection issues receive different priorities in different states and communities within those states. State reclamation requirements in general provide the flexibility to consider site-specific circumstances, allowing operators to design and engineer the best reclamation measures for each mining site. To the mine developer or manager, reclamation requirements must be translated into design, operational, and closure measures for mine planning. Each of these measures must then be assigned additional costs to be factored into the economic decisions for a particular mining operation. On a broader level, reclamation costs must be factored into decisions such as where to invest in exploration and mine development. The purpose of this paper is to provide a summary of the state non-coal mine reclamation requirements in twelve western states. This summary comparison may be useful as a starting point in considering how local reclamation requirements will impact potential mining costs.

Jan 1, 1994

By M. de Paiva Bueno, G. Barakos, S. Luukkanen, K. Luolavirta

Lifelong development of skills and knowledge of mining professionals has been recognised worldwide as a challenge for the development of a sustainable mining sector. Practical training and learning over the mine value chain are among the key components of this knowledge building. However, the number of available mining sites for continuous education in real-life conditions is limited; also the specifications for practical training are not clearly defined. The project MINETRAIN was developed to (i) evaluate the potential of the shortly-closing Pyhäsalmi Mine, in Finland, as an educational and training underground facility, and thus, prolong the utility of the existing modern mine site, and to (ii) develop and test practical training programs for mining and mining industry related professionals. Pyhäsalmi facilities enable training among all disciplines related to the overall mine value chain and hence, the project has potential in providing education for sustainable management of any phase of mining operations. The philosophy underpinning the MINETRAIN approach to mining activities is to assist the clients in minimising the technical and financial risks by providing a competitive and skilled personnel asset while optimising the value drivers in their operations. As a first major step of the project, a pilot training course, involving basic-level online theory and hands-on training at the Pyhäsalmi mine site, was undertaken in summer 2019. Feedback from the pilot test group of mining professionals has proved to be very positive. The comments from the participants strongly emphasised the added value of the practical onsite training for improved understanding in the large scale picture of mining on the entire value chain. As a second phase of the project, a new test course was launched in June 2020. The second MINETRAIN course focuses on new technologies and digitisation in mining. Keywords: Lifelong learning, mining education, mine value chain, research and education mine, educational research project

Jan 1, 2020

By R Wynn, T J. Akroyd, C Costa

In an environment of lower zinc prices, falling revenues and reducing zinc feed grades, Century mine implemented a fast-tracked capital upgrade program in less than 15 months. The program was designed to increase ore milling throughput capacity by 20 per cent and optimise the capacity of the flotation plant to increase zinc recovery by approximately 2.5 per cent whilst maintaining final zinc concentrate grade.A key aspect of this program was minimising capital expenditure by better utilising existing capacity and only adding capacity where absolutely required to address critical processing bottlenecks. By gaining an understanding of plant process bottlenecks and future ore blends, and by carefully selecting appropriate technologies for particular specific flotation applications, maximum return on minimal capital investment was achieved.The close collaborative work achieved between the metallurgy processing department and other operational departments on-site was also critical to the success of this project. This work increased the mining and processing capacity of the mine and port site respectively, such that the full value of the process plant modification could be achieved.Capital payback on this investment was achieved in approximately three and a half months.This case study demonstrates the extra value to a mining business that can be achieved through fully understanding the mining/processing value chain and by careful targeted action to address critical bottlenecks in the processing chain from the mine through to the port site.CITATION:Akroyd, T J, Wynn, R and Costa, C, 2014. MMG Century Mine, a case study – maximising project net present value through targeted capital expenditure and process optimisation against a backdrop of falling metal prices and feed grades, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 417–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D Tanzil, H Jones

Every mine will close! Charting a profitable course through mine operations to acceptable mine completion requires that risk and opportunity management planning of the mine life begin as early as possible in the life cycle. Management targets and metrics are required to identify and navigate the course to successful mine completion based on economic, social and environmental criteria. This paper outlines the application of The Metrics NavigatorÖ principles to the life cycle of a mine site. In general, metrics are required to make key strategic ideas apparent, transforming those ideas into a manageable set of quantitative measures that guide communication and decision making. For example, the chemical industry has established metrics that focus on the life cycle impacts of its products and eco-efficiency of their processes. Other industry sectors have focused attention on workplace and community well-being outcomes. These management metrics are necessarily organisation-specific, aligned to stakeholdersÆ expectations and the strategic outcomes sought, as well as the cause-and-effect relationships underlying key issues. Recently, the Global Environmental Management Initiative (GEMI), a consortium of multi-national companies, developed The Metrics NavigatorÖ. The guidance document provides a structured process for assessing and developing metrics for key environmental, social, and economic issues based on business and stakeholder perspectives. It incorporates best practices learned from the chemical and other industry sectors and has since been applied to develop metrics that guide life cycle strategies. The paper examines how the life cycle of a mine site could benefit from experiences in other industry sectors where sustainability metrics have guided strategy. It considers the potential application of The Metrics NavigatorÖ process to the life cycle of a hypothetical Australian mine site using the processes that have been successful in other industry sectors.

Jan 1, 2009

By I Elias, E Moya, S Chaffer

This paper is based on a case study from a mine site that operates two gyratory primary crushers. These crushers were encountering problems, which included inconsistent P80, reduced liner life tonnage and, on some occasions, catastrophic failure of the liners.As part of an evaluation process, both crushers were ‘mapped’ using a technology for condition monitoring and modelling of the crusher’s wear components. The technology provides comprehensive coverage of the crusher’s concaves and mantle at 100 mm intervals. It also automatically assesses wear rate between inspections and determines the highest wear areas. Outcomes include projected optimum reline dates at target replacement thicknesses, the identification of asymmetrical wear patterns, and the accurate measurement of open and closed (OSS/CSS) side settings.A comprehensive study was performed to optimise the performance of both these crushers at site. Over a period of seven liner service lives, the strategies to improved performance included liner analysis (concaves and mantle profile analysis), tonnes per day (t/d) and tonnes per hour (t/h) analysis, mantle reutilisation, detection and control of loose concaves, and detection and control of uneven wear and hot spots.These strategies resulted in the improved mechanical and operational performance of both crushers through concave and mantle redesign, OSS/CSS control, accurate wear forecasting plus other initiatives.As a result of these initiatives, the site now experiences benefits which include consistent product size, increased tonnes per hour (t/h) for both crushers and the liner life tonnage has doubled. Additionally, further benefits include less downtime for crusher liner maintenance and the reduced cost of inventories by mantle reutilisation.CITATION:Elias, I, Chaffer, S and Moya, E, 2015. Improvements in service life and cost reduction for gyratory primary crushers through mantle and concaves optimisation – a case study, in Proceedings Iron Ore 2015, pp 115–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By R. ?. Shishmarjov, Yu. ?. Davidenko, S. V. Bukhalov, ?. S. Baksheev, M. S. Shkirya, N. ?. Aikasheva, D. V. Bogdanovich, ?. Yu. Faustova

"The goal of prospecting operations in the Republic of Altay was to locate gold-sulfide-quartz mineralization. For this purpose we applied the technology of electromagnetic sounding and induced polarization (EMS-IP). These operations resulted in localizing promising sites with presence of sulfidization. The EMS-IP method proved to be highly efficient amongst other prospecting methods targeted at recognizing zones of sulfide mineralization making up 91%, considering that in more than half cases the ore intervals were the case. In the Yakutian diamondiferous province the EMS-IP technology was approbated during three field seasons to accomplish the assignments on searching for kimberlite bodies under conditions of various geological types. As a result, the reference objects were distinguished, and geoelectric parameters of kimberlite pipes of explosion were defined.INTRODUCTION In the time span 2015-2016 in Gorny Altay the EMS-IP technology was approbated in the Novokuznetsk area. The on-land areal geophysical survey was performed by EMS-IP method applied to identify, outline and locate promising sites with Au-Ag-bearing polymetallic mineralization within surveyed areas. Compared to the hosting rocks, the sulfides contained in polymetallic mineralization are typified by low specific electrical resistivity (SER) and high polarization. The areal survey conducted via EMS-IP method provided spatial characteristics of searched object. From July 2016 to August 2017 our expedition group carried out serial test works and laboratory investigations intending to define performance capabilities of EMS-IP technology in searching for kimberlite bodies under conditions of diverse geological types. The prerequisites for serial work were operations accomplished at the «Listvenichny» site lying 35 km away from Mirny town in the Sakha Republic (Yakutia), where the EMS-IP technology was probed for locating position and measuring geoelectric parameters of tuff pipe «Buardakhsky». After successful completion of operations it was decided to evaluate geoelectric parameters of kimberlite pipes of explosion."

Jan 1, 2018

To solve the mining safety and health needs of the future, access to, and sharing of, timely and relevant information will be crucial. The next generation of the Web will provide tools (RDF, OWL, SPARQL, etc) to define and link content for more effective discovery, integration, and reuse across applications and organisations. A recent Gartner Research Report (Finding and exploiting value in Semantic Web technologies on the web, May 2007) predicts these technologies will begin to coalesce in ten years. Implementing this Semantic Web requires structured web content described via metadata (information about information). If an industry or enterprise bases its metadata on a common vocabulary, it becomes possible to share and reuse information. The National Institute for Occupational Safety and HealthÆs (NIOSH) Mining web site provides access to more than 1500 NIOSH-developed publications, products, and topic pages on issues as diverse as ground control, respiratory diseases, and mine emergency management. As the site has grown, locating content has become increasingly difficult. To improve the searching process, a panel of internal experts representing all major research programs was established to develop a controlled vocabulary for indexing that content. The outcome is the NIOSH Mining Safety and Health Thesaurus, a faceted, hierarchical thesaurus containing hundreds of mining safety and health terms organised into 20 facets (eg diseases, injuries and disorders; hazardous events and exposures, equipment, engineering and administrative controls). One immediate goal of this project is to reduce the complexity of locating information on the NIOSH Mining web site by implementing metadata and faceted information retrieval techniques. Another goal is to stimulate discussion in the international mining community regarding developing metadata standards so the industry is ready to adopt future Semantic Web technologies to improve access to mining safety and health information.

Jan 1, 2008

By D. Dreher Whetstone, Paul M. Blakita, Christopher M. Reith, Ravi P. Malviya

"Micro-piles are small diameter (5 to 10 inches), cast-in-place piles which can develop high load capacities by bonding with soil or rock. Micro-piles are particularly well-suited for moderate to heavily loaded structures requiring deep foundations in difficult subsurface conditions, such as karst, bouldery mine spoil, or unsuitable fills with concrete debris or other obstructions. Attempts to install conventional deep foundations including driven piles, drilled piers, or auger-cast piles are likely to be fraught with construction difficulties and disputes, delays, cost overruns, and may be unfeasible in some cases. Micro-pile installation equipment is very effective in installing foundations through such overburden or rock materials.This paper presents case histories of Micro-pile installations on two projects with difficult soil/rock materials. The project sites are located in Charles Town, West Virginia and Masontown, Pennsylvania.Charles Town, West Virginia ProjectThe Charles Town project entailed construction of a four-story pre-cast concrete garage. Triad Engineering, Inc. performed a geotechnical investigation for this project (Triad, 2001). The subsurface, geologic, and project specific information described in th is paper are largely based on the aforementioned geotechnical report.Ground ConditionsThe project site is located in Jefferson County, West Virginia, and is mapped to be underlain by the Elbrook Formation. This formation is described as argillaceous, dolomitic limestone with beds of dolomite and aphanitic and algal limestone (Dean, et al. , 1990). The carbonate rocks at the site were characterized as ""moderately solution-prone, highly calcareous and weathers differentially to produce a pinnacled or ""sawtooth"" top of rock profile. (Triad, 2001 )"" Overburden soils consist of low to high plasticity, fine grained residual soils formed by weathering of the parent carbonate rock. The residual soils include variable proportion of sand and rock fragments."

Jan 1, 2005

By M Jacobs

This abstract discusses a heap leach copper mine that was failing to perform and as a result was not meeting targeted production. The mine had numerous technical challenges including: high water inflows, low levels of geotechnical monitoring, performance issues with mining, resource model and grade control reconciliation issues, and unexplained low levels of performance from the heap leaching operations. A team from various organisations with specialist skill sets including: a forensic accountant, the owner’s representative and a mining engineer, was arranged to visit the site. The task was to investigate the situation and determine what could be done to turn the performance of the mine around. After an initial assessment in late 2018, efforts were directed to better understanding the operations and improving the performance of the site through preventative management. A key part included the creation of production forecasts that could be achieved that would help restore confidence in the operations. Uncertainty in the mine achieving production forecasts and the performance of the heap leaching operations were contributing to the decline of the operations. Investigations uncovered the fact that while the resource model could reliably predict total copper, a lack of sequential leach data meant the accurate prediction of soluble and insoluble copper species, both important for heap leaching, was difficult to do with any degree of certainty. The crushing and mining contractors also appeared to have suffered somewhat from a lack of management by the owner’s team and performance had affected the production of copper. Collaboration and management were used by the team to understand and stabilise the operations. Ongoing collaborative efforts by the management team, site personnel and contractors resulted in a positive outcome for the owners and their mine – and could at yours.

Jun 22, 2022

By Arthur L. Murray

"Oil-shale camps are peculiarly favored, in that before they are established it can be ascertained with a,of certainty, that the life of the project is not limited. Unlike camps at metal mines, where the metal content of a given area is frequently an unknown quantity until after years of development, oil-shale camps should, from the outset, be planned and built as permanent types of camps. Where this procedure is followed camps will be established which better serve the needs of the industry and the cost of their general care and upkeep will be less.Selection of camp or townsite.The site of the camp or town, whether on company property or not, should be selected with care. It should be separate if possible from the location of the plants of the company so as to be free from noise and fumes and so as to provide a change of environment for employees in going from their work to their homes.The principal features governing the site to be selected are as follows:Drainage. The general contour of the surrounding country should be such that drainage is away from the site. The camp or town should, if practical, be situated on higher ground than that in its immediate vicinity.Soil. The nature of the soil on which the camp or town is located may bear a decided relation to health. A porous, well under drained top soil of at least four feet in depth insures dryness and facilities the placing of foundations and the laying of water mains and sewer pipes. Such a soil also is an advantage in growing trees, shrubs and grass plots, which are a decided adjunct to making the community attractive."

Jun 1, 1921

By M Grigorescu, S Crimp, J H. Hodgkinson, P Kokic, W Jin

Mines are typically located in remote, inhospitable locations and movement of materials between site, processor and port are often at risk from extreme weather events. Mining companies have recorded multiple supply chain, production and logistics delays caused by climatic events. Recent analyses of extreme temperature and rainfall events (90th and 99th percentile values) for 1960 to 1985 and 1986 highlighted regionalised increases in the frequency and intensity of extremes. The trajectory of this change is likely to be maintained (IPCC, 2014) in regions where increases have occurred historically, suggesting that some parts of the industry may be faced with management challenges beyond current experience (Hodgkinson et al, 2010; Loechel, Hodgkinson and Moffat, 2012). Reliance on historical data to plan for extremes (such as scheduling production downtime to reduce impact) will become increasingly ineffective as the data become less representative of future conditions. Importantly, mine site remediation and closure management need to consider the future climate to ensure rehabilitation is sustainable under changing conditions.Vulnerability assessments and risk-reducing adaptation will become more common as the industry reaches to secure both a mine’s longevity and the industry’s reputation as shareholders and clients become less tolerant of repeated or prolonged interruptions (Hodgkinson, Hobday and Pinkard, 2014). Climate-resilient new mines may be planned using site planning tools combined with knowledge of future climate scenarios. Scenario tools are valuable for developing a gated risk management approach to reducing climate-risk during a mine’s life, through to the rehabilitation process and for managing care and maintenance or closed mines.CITATION:Hodgkinson, J H, Crimp, S, Jin, W, Kokic, P and Grigorescu, M, 2016. Life-of-mine planning tools for a changing climate – intuitive, interrogative, iterative, in Proceedings Life-of-Mine 2016 Conference, pp 71–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Norm Kirk, Robert Bittner

"The addition of a new powerhouse at the existing Tulloch Hydroelectric site on the Stanislaus River in the western foothills of the Sierras Nevada Mountains of central California required a deep excavation in rock on the downstream face of the dam. A cofferdam (water exclusion device) was necessary to isolate the powerhouse construction site excavation from the existing Goodwin Reservoir and the turbulent discharge from the existing powerhouse. The cofferdam was positioned on a steeply sloping fractured rock surface exceeding 50 degrees.This paper describes the challenges encountered during design and construction of the cofferdam and describes the unique design features used to address these challenges including:•,The use of flat-sheet-piles to form cellular walls on the steeply sloping rock surface.•,The use of 5-ft deep tremie concrete plugs in the bottom of the sheet pocket cells to create the bottom seal of the cellular cofferdam walls against the sloping rock surface.•,The use of vertical post-tensioned rock anchors to provide shear resistance at the contact point between the base of the cellular-wall and the sloping rocksurface.INTRODUCTIONModification or expansion of existing hydroelectric power plants often require downstream cofferdams or water exclusion devices to temporarily separate new construction from turbulent downstream discharge of the existing dam. Most dams are positioned on solid rock in the narrowest and therefore the steepest section of the river. This combination of steeply slopingrock and the need for an exclusion barrier creates a challenge for the design engineer trying to maintain a safe dewatered construction site. Typical cofferdam solutions for hydroelectric dams usually use large granular filled circular sheet pile cells that perform as gravity structures. However, this type of structures is not well suited to steeply-sloping highly irregular rock surfaces in a confined area."

Jan 1, 2017

By Bowler Jonathan, Lorraine Kent, Tereza Crisu, Stuart Walker, Nicholas Lightfoot

"It has been the practice in Europe to extract the most economic seams first: taking the seams sequentially, top down, to avoid operating within the fractured strata formed by the subsidence trough above previously mined coal seams. In the 1990s, the UK coal industry found itself at a number of sites having to operate over one or more previously mined seams. This led to specific geotechnical challenges with respect to maintaining economic, safe and stable rectangular roadways with rock-bolted support.Within this paper, the current challenges and mitigation strategies of overmining in the UK are described following the completion of a -three-year European Commission-funded project in 2015. The challenges and mitigation strategies are related to:• A case study with overmining of older workings of variable geometry;• Numerical modeling for overmining layout and support design; and• A case study site planning mine layout when considering future overmining.INTRODUCTIONAt the first case study site, case histories were examined for a mine operating at a depth of approximately 700 meters where five longwall panels were extracted above workings 35-40 m below. The overmining of various extraction geometries below led to challenging conditions in areas of high vertical stress concentration. It was found that results from one longwall panel could be suitably used to predict behaviour in a subsequent panel. The experience was used to update previously existing guidelines on the positioning of roadways in relation to subsidence troughs. Existing guidelines recommended that only as a last resort should longwalls be planned to retreat over narrow pillars, or from solid ground into a subsidence trough. Existing guidelines regarding the layout of overmining panels are conservative, and new work indicates that such multi-seam geometries are possible with appropriate support management strategies."

Jan 1, 2016

By Takeo Ueda, Masashi Nakano

We have developed a new blasting system remotely controlled by an electromagnetic firing method, which has proved advantageously applicable to sites where rapid tidal current or deep water may cause serious troubles in underwater blasting operation by a conventional method.

Jan 1, 1983