Search Documents

By C J. Moran

The Gladstone region, as one of the most industrially intense regions in Australia, uses significant quantities of fresh water. Awoonga Dam, situated on the Boyne River, is the only major source of water in the region. The current typical annual usage is 53 GL (Porteous, 2006) and approximately 80 per cent of the water is used by heavy industry (Gladstone Area Water Board, 2004). Until relatively recently, there has been ready and easy access to raw water for industrial use. The recent drought, which resulted in severe water restrictions in 2002 and 2003, emphasised the importance of water for a dominant industrial region like Gladstone. Although now in the process of changing, the typical contractual arrangements in the past have provided little financial incentive for efficient water use. From research undertaken on potential water reuse opportunities, several key questions have emerged related to water management in an industrial region such as Gladstone. This paper highlights these key questions, presents findings from recent regional strategies and assesses the potential for water reuse. Even though there is no clear-cut financial incentive for reusing water, there could be stronger regional and risk mitigation drivers for doing so. Initiatives to incorporate adaptive capacity through collaborative industrial synergies would allow for robustness and resilience in water security, leading to long-term sustainable water management across the Gladstone region.

Jan 1, 2006

By Henri-Loui Jacob, Suzie Nantel

"Depuis la fin des annees 1800, la province de Grenville represente pour Ie Quebec une source importante et diversifiée de minéraux industriels. Le Ministère de l'Énergie et des Ressources du Québec, dans Ie cadre de I'entente auxiliaire Canada-Québec, et les compagnies minieres y ant multiplié, surtout depuis 1983, leurs travaux d 'exploration, de cartographie, et d'évaluation pour les minéraux industriels. Ces travaux ant conduit ala découverte et ala mise en valeur de gisements de granite architectural, de graphite, de dolomite et ant aussi permis de repertorier des gîtes et des indices prometteurs de wollastonite, de silice, de calcite. de dolomite, de silicates d'alumine et de terres rares. Les gisements récemment découverts sont actuellement exploités au sur Ie point de l'être et les gîtes et les indices les plus prometteurs ant été jalonnés.ABSTRACTSince the late 18oos, the Grenville Province in Québec has been an important and diversified source of industrial minerals. The Ministere de l'Énergie et des Ressources du Québec, under the Canada-Quebec Mineral Development Agreement, and the private sector have put an emphasis on exploration, mapping and evaluation programs in the Grenville Province for minerals, particularly since 1983. These programs have led to the discovery and the development of deposits such as architectural granite, graphite and dolomite, and have also led to inventories of occurrences and prospects of wollastonite, silica, calcite, dolomite, alumina silicates and rare earths. The deposits discovered lately are presently being quarried or will be in the near future. The most promising occurrences and prospects have been claimed."

Jan 1, 1990

By R. J. Hickson

The Grasberg copper-gold deposit was discovered in Spring 1988, just one year prior to the planned closure of Freeport Indonesia's original Ertsberg open pit copper mine. In spite of Grasberg's remote location, 600m above the Ertsberg, atop a hitherto inaccessible mountain, Freeport-McMoRan brought their latest open pit mine into production in the last week of 1989, less than two years after discovery. This paper describes the start-up of the operation, highlighting synergies drawn from both the original Ertsberg experiences and the current Freeport Indonesia underground mines.

Jan 1, 1991

By P Oikkonen

Sprayed concrete has played an integral role in underground rock support for nearly a century. However, concrete is also considered to be one of the biggest environmental problems in construction and mining, largely because of the high carbon footprint of cement and aggregates production. This is driving the industry to find ways to cut concrete usage where possible. Improving sustainability by cutting concrete material consumption also reduces application time and costs. Improving concrete properties can make it possible to design thinner linings, but as awareness of safety and longer design lifetimes are driving developments in the opposite direction, it is not realistic to see this as a major factor in cutting concrete consumption. More accessible solutions are focusing on layer thickness control and minimising rebound and wastage. Digital technology and innovation offer excellent tools for improving sustainability while optimising other aspects of the spraying process at the same time. A digital layer thickness control system gives near-real-time information to the sprayer operator with full coverage of the sprayed surface. This enables the operator to achieve consistent layer thickness on the first pass, in comparison to the traditional methods of overspraying with the aim of achieving sufficient layer thickness, probe drilling after the concrete has set, and respraying at a later stage if needed. Operator competence is the single biggest variable in a successful sprayed concrete process, affecting rebound and wastage levels. Unfortunately, the learning curve to become a master sprayer is quite steep and training on a real sprayer and real concrete requires a significant amount of time and money. Training in a virtual reality (VR) environment enables operator training to be carried out in a low-risk environment and provides a way of measuring performance and assessing and certifying the operators. After the VR training period, a novice nozzle operator has the basic understanding to start working on a real sprayer, and an experienced nozzle operator can benefit from the possibility of assessing their performance.

Mar 29, 2023

By E Amini, M Scott

Grade Engineering® involves the planning, integration and operation of coarse preconcentration techniques to reject uneconomic material as early as possible in the mining value chain to improve the quality of ore delivered to mineral processing activities. These preconcentration techniques include screening for natural and induced deportment of grade to finer size fractions during blasting and coarse breakage, sensor-based measurements of grade and mechanised sorting at particle or bulk scales and coarse gravity separation. Over the last decade, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE), with the support of its participants, has developed a framework for the holistic evaluation of economic and production impacts attributable to these preconcentration techniques. The framework combines the characterisation of preconcentration responses, geostatistical modelling, process modelling and simulation of downstream and upstream production impacts and the optimisation of strategic mine plans to quantify changes in net present value due to different preconcentration strategies. This framework has been applied to evaluate preconcentration techniques at numerous metalliferous operations and can also be used to quantify changes in the environmental metrics for energy, water and steel consumption and emission, tailings and waste rock production. This paper collates the results of these Grade Engineering® studies to show the range and magnitude of economic and environmental impacts attributable to preconcentration. The studies have shown that rejection of uneconomic material prior to mineral processing activities can have a pronounced improvement in energy, water and comminution steel productivity, emission intensity and the profitability of metalliferous mining.

Nov 10, 2020

By D. Kumar, R. J. Sweigard, J. Silva

The Forestry Reclamation Approach (FRA) recommends that the upper 1.22 m (4 ft) of spoil material on reclaimed surfaces should be left as uncompacted as possible to facilitate efficient tree root growth. However, the main concerns about applying the FRA to steep slopes is that the upper 1.22 m (4 ft) of loose spoil material could cause instability. Successful application of the FRA on the flat and rolling surfaces precipitated this investigation. Details of a field investigation conducted at a steep-slope mine site are available in an earlier publication (Kumar and Sweigard, 2011). A total of 70 survey monuments were driven into the slope in a regular pattern to monitor any type of slope movement. Quarterly surveying of the monuments were done to quantify slope movement, either horizontally or vertically. The methodology developed in this research for field slope movement monitoring was validated using computer model results. Analytical models based on the limit equilibrium method (LEM) and numerical models based on the finite element method (FEM) were developed for slope stability analysis. The LEM analysis was done using the Geo-Slope/W program following the simplified Bishop method. However, numerical models were developed using the PLAXIS computer program following the Mohr’s Coulomb failure criterion and strength reduction technique. The slope stability analysis was performed for two different scenarios: first with the top 1.22 m (4 ft) of loose graded spoil material and second without top loose graded spoil material. Finally, the field investigation results were compared with stability analysis results. Both of these approaches showed that application of the FRA on steep slopes is not causing any significant instability problems, due to 1.22 m (4 ft) loose graded spoil that would not exist otherwise for overly steepened slopes.

Jan 1, 2013

By K. Osseo-Asare

It is possible to form a two-phase system in certain polymerlinorganic salt/water mixtures, such as those containing the polymer polyethylene glycol (PEG). Such aqueous biphase systems have many of the separation characteristics of conventional solvent? extraction systems, but are environmentally friendlier. Just like the well-known organic solvent/water two-phase system, the top polymer-rich phase is more hydrophobic. and the bottom salt-rich phase more hydrophilic. The partition of dispersed? particles is dependent on the interfacial interaction between the particles and the conjugate aqueous biphase solutions. In particular, the hydrophilic/hydrophobic properties of the surface determine the transfer of the dispersed particles into either the top (more hydrophilic) phase or the bottom (more hydrophobic) phase. Accordingly, differences in the surface chemistry of particles can be exploited to achieve selective separations. In this work, several approaches to separation control will be discussed. using pyrite (FeS2), alumina (AI203). hematite (Fe203), silica (Si02), and titania (Ti02) as model particulate materials. For metal sulfides, pH and redox potential can be used to alter the hydrophobicity/hydrophilicity of the particles. In ?the case of oxides. polymer adsorption and collector adsorption may be exploited to facilitate particle transfer.

Jan 1, 1999

By James H. Barks

Exploration for ore deposits in southeastern Missouri in the 1950's resulted in the important discovery of lead, zinc, copper and silver in 1955. Further discoveries in the area led to the naming of the Viburnum trend. It has sometimes been referred to as the "New Lead belt" to distinguish it from older lead-producing areas to the east. As presently developed, the "trend" is 35 miles long, running north and south about 50 miles west of the Lead belt. Galena (lead) is the principal ore mined, with lesser quantities of sphalerite (zinc), chalcopyrite (copper) and silver recovered as economic by-products. The ore body is as much as 140 feet thick and 1,200 feet wide, and is found in the Bonneterre Dolomite (Upper Cambrian) at depths ranging from 700 to 1,200 feet. Since its discovery many companies have engaged in exploration and several major companies have developed new mines and constructed mills and a smelter in the area. The first mine in the Viburnum trend came on stream in 1960, but as more mines came on stream and others reached capacity, lead production increased to the point that the Southeast Missouri Lead district produced 432,576 tons of lead in 1970 to become the world's largest lead-producing region (Missouri Geological Survey and Water Resources, 1971). The Viburnum trend area with its rolling, heavily forested hills and numerous clear running streams is in the Clark National Forest of the Missouri Ozarks. Until the recent development of its mineral resources, the area was sparsely populated and nearly unmarked by the activities of man. Industrial development is almost certain to be accompanied by environmental changes. In a day of growing awareness of the need to preserve the quality of the

Jan 1, 1971

By Tim Gitzel

Thank you for your introduction, and thank you to the CIM for inviting me to make a presentation to you today. This is my first opportunity to report to you on the status of the Canadian uranium industry and I am pleased to tell you that the industry is in good shape, and well positioned for the future. As you will no doubt be aware, Saskatchewan benefits from the world?s largest known highgrade deposits of uranium as well as from a high level of provincial, public and northern community support. It is within this unique combination of geology and community that our industry operates. Uranium markets have been extremely competitive for a number of years for several reasons. First, deregulation in the nuclear electric power industry has tended to encourage fuel buyers to use up their large inventories built up at a time when rapidly increasing demand was anticipated. Second, alternate sources from surplus commercial stocks, military materials and reprocessed fuel have presented a major additional source of uranium supply. Today, these secondary supplies are meeting about half of uranium reactor feed requirements. Canada (that is, Saskatchewan) is the world?s largest ?natural? uranium producer with about a third of the global production. Saskatchewan?s mines produced more than 30 million pounds of yellowcake in 2002. Despite low prices, steady demand for uranium will continue. In fact, an increase in world uranium production in 2002 helped feed a more than 3 per cent increase in reactor fuel demand. Low cost production is important for surviving low market prices, but investments are based on longer-term strategies rather than simply responding to market cycles. Cost is not the only issue. In these times of increasing regulatory and public scrutiny we must continue to earn the trust of our stakeholders by adopting the highest standards and staying on the leading edge of technical, social and environmental developments. Managing these issues is as important as traditional concerns of ore grade and cost of production. The last two decades of the 20th century saw the Province of Saskatchewan rise to prominence as the leader in uranium production from facilities, which were at the time deemed world class. These facilities are now either at - or nearing - the end of their production years. We are now bringing on new facilities that will position Saskatchewan to remain the world leader in uranium production for many years to come.

May 1, 2003

By Theodore H. Eyde

In 1971, the Minerals Division of The Superior Oil Company acquired exploration rights to an unpatented claim group in the Superior (Pioneer), Arizona mining district, lying west of the Concentrator fault. This major post-mineral fault displaces the Magma vein-fault, which is mined in the Magma Mine at Superior, Arizona. The Magma vein-fault and the enclosing section of pre-mineral rocks consisting of Paleozoic and younger Precambrian sediments and diabase, is overlain by a thick section of post-mineral rocks, consisting of the Gila conglomerate, the Apache Leap dacite, and the Whitetail conglomerate. Geologic information on the thickness and attitudes of the rocks obtained from previous diamond drilling indicated that the section of post-mineral rocks might be from 3,000 to over 4,010 feet thick in the target area. (Figure 1) The Magma vein-fault is a steeply dipping vein which has produced nearly a billion dollars of copper, zinc, silver, and gold. It has been mined continuously for nearly 10,000 feet along the strike and nearly 5,000, feet vertically down the dip. It ranges from less than a foot to over 50 feet wide and contains sulfide mineralization con¬sisting of pyrite, chalcopyrite, bornite, and chalcocite.

Jan 1, 1973

By Lance Rasband, Richard Hanke, John Starcevich

"The world’s largest tunnel boring machine (TBM), at the time of her launch in 2012, the TBM locally referred to as “Bertha,” is incapacitated due to mechanical failure. Bertha’s stoppage places her 25m below the surface between the aged Alaskan Way Viaduct and the failing Seattle Seawall. Accessing Bertha with a vertical shaft provides the best approach to access all facets needed for repairs and will allow the full removal of Bertha’s cutter head and related inner workings. Due to the limited area above the tunnel alignment and physical constraints created by existing infrastructure, the dimensions of the otherwise symmetrical shaft are heavily impacted, thereby requiring special attention to design and layout. Consequently, the shaft design required a combination of 3m, 2.5m, 2.2m, 1.5m and 1m diameter unreinforced drilled secant piles coupled with various ground improvement techniques and dewatering, to fully satisfy the shoring design requirements. This paper will describe the shaft installation procedures, equipment used and pitfalls encountered while undertaking access shaft construction of this magnitude. INTRODUCTION Mining on Seattle’s SR99 tunnel began in July of 2013. Initial mining progressed slowly through a 4.5 m thick fiber-reinforced concrete headwall before immediately entering the first of three planned safe havens. Once through the headwall and safe haven the machine would move through roughly 122 lineal meters of jet grout improved soil at a rate of slightly over 1.6 m per day. It was anticipated that once mining has passed through the improved area, “Bertha” – now the world’s 2nd largest tunnel boring machine (TBM), would be moving at a rate of almost 11 m per day. By the end of October 2013, Bertha had mined roughly 131 m, averaging 1.4 m per day, and had begun mining within native soils. By the start of December 2013, tunneling had reached the 244 m mark and Bertha was now averaging 3.6 m per day, achieving as much as 12.8 m of progress on given days. Unfortunately, on December 6th, 2013, Bertha began to stumble and all progress quickly came to a halt. Initial reports stated an obstruction had stopped Bertha in her tracks. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic pressure within the ground around the TBM, to allow the contractor’s personnel to inspect the cutter head from within and also to investigate for the presence of obstructions at the face of the cutter head. During inspection, the contractor’s crews found fragments of steel pipe entangled in the cutter head. The steel was apparently from an abandoned 254 mm diameter monitoring well casing, previously installed by WSDOT to monitor ground water conditions for the design and planning of this tunnel project. After the steel was removed from the cutter head and cleared from Bertha’s path, she attempted to move forward but was only able to generate a slow crawl."

Jan 1, 2016

By Ali Kahriman, Olivio Angelini, Ibrahim Sefer, Burak Ekmen, Koray Arpak, Ertugrul Kaya, Yucel Karakus, Abdullah Sak, Aziz Ozdemir

In recent years, in order to bring solution to traffic intensity arising from transportation problems and facilitate public transportation in the modern world in paralel to urbanization and to the increase in population, it’s well known that, the construction of Access tunnels is inevitable. The driving of the tunnels is a subject of special interest in the technique of rock blasting. The essential factors in terms of tunnel driving and safety in tunnel blasting that is applied in metropolitan areas, an in depth knowledge of ground vibrations and the ways of reducing them to safer levels.

Jan 1, 2010

By A. Ashrafi

The electrochemical deposition of polypyrrole coating on different pretreated aluminum-alloy 7075 substrates was carried out using cyclic voltammetry, The pretreatment of specimens consisted of mechanical polishing and/or electrochemical etching, In the latter case, an aqueous solution of phosphoric acid and ethanol was used, The electrodeposition solution was 0,25 M pyrrole and 0,1 M oxalic acid in double-distilled water, The cyclic voltammetry scan rate used was 700mv/s, Morphology of the coatings was examined using scanning electron microscope (SEM), Using the Tafel experiment, corrosion resistance of the coated substrates was investigated in 0.1 M NaC1 solutions, Results obtained revealed that electropolymerization of polypyrrole on 7075 aluminum alloy would increase the resistance against corrosion in 0,1M NaC1 solution, Also it was observed that, compared with mechanical polishing, electroetching pretreatment would be more effective.

Jan 1, 2005

For Australian mining projects, sustainable groundwater use is typically defined as a groundwater extraction regime, measured over a specified planning time frame, which allows acceptable levels of stress and protects dependent economic, social and environmental values (DEH, 2004). This principle is compatible with most stakeholdersÆ understanding of our national environmental objectives, yet the application of this policy on a project-specific scale is not always straightforward. Three examples of sustainability issues in the management of groundwater in mining are presented. These examples highlight each of the three dependent values: environmental, economic and social.

Jan 1, 2006

By Lance Rasband, Richard Hanke, John Starcevich

"The 17.4 meter (57 ft) diameter tunnel boring machine (TBM), the world’s largest at the time of her launch in 2012, locally referred to as “Bertha,” is stuck. Incapacitated due to mechanical failure approximately 36 meters (120 ft) beneath downtown Seattle, situated precariously between the deteriorating Alaskan Way Viaduct and the failing Seattle Seawall. Accessing Bertha with a vertical shaft provides the best approach to address all facets needed for repairs and will allow the full removal of Bertha’s cutter head and related inner workings. Limited area above the tunnel alignment and the physical restrictions of existing infrastructure, create significant challenges for the design of an otherwise symmetrical shaft, requiring special attention to design and layout. Consequently, the access/recovery shaft design required a combination of 3m, 2.5m, 2.2m, 1.5m and 1m diameter unreinforced drilled secant piles coupled with various ground improvement techniques and dewatering, to fully satisfy the shoring design requirements. This paper will describe the shaft installation procedures, equipment used and pitfalls encountered while undertaking access shaft construction of this magnitude.INTRODUCTIONTunneling on Seattle’s SR99 tunnel project began in July of 2013. After slowly mining through a 4.5 m (14.76 ft) thick fiber-reinforced concrete headwall and the first of three stabilized “safe havens,” Bertha would proceed along the proposed alignment through 122 meters (400 ft) of jet grout improved soil at a rate of slightly over 1.6 m (5.25 ft) per day. Once past the improved area, it was planned that “Bertha” – would be moving at a rate of about 11 m (36 ft) per day. By the end of October 2013, Bertha had mined roughly 131 m, (430 ft) averaging 1.4 m (4.6 ft) per day and had begun mining within native soils. By December 2013, tunneling had reached the 244 m mark and Bertha was averaging 3.6 m (11.8 ft) per day, achieving as much as 12.8 m (42 ft) of progress on given days. Unfortunately, on December 6th, 2013, Bertha began to stumble and all progress quickly came to a halt.It was initially reported that an obstruction had stopped Bertha in her tracks. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic pressure around the TBM, and allow visual inspection of the cutter head from within the TBM, and also to investigate for the presence of obstructions at the face of the cutter head. During this inspection, fragments of steel pipe were discovered entangled in the cutter head. The fragments were apparently from an abandoned 254 mm (10 in.) diameter monitoring well casing, previously installed by WSDOT to monitor ground water conditions for the design and planning of this tunnel project. After the steel was removed from the cutter head and cleared from Bertha’s path, tunneling resumed. It was then discovered that Bertha was only able to generate a slow crawl."

Jan 1, 2016

By S Bhandari

A model for predicting dust plume dispersion from blasting operations using the Eulerian mathematical algorithm has been developed. This model considers atmospheric stability, and wind velocity and direction for computing dust concentrations at different distances from the blast. Software has been developed which simulates the movement of a dust plume at a given horizontal distance from the blast location and time elapsed after the blast. The concentration of dust is also given in vertical planes. It takes into account ground profile and atmospheric conditions such as temperature, pressure, humidity, wind velocity, wind direction and shear. Experiments were carried out in two limestone mines to calibrate the accuracy of the predictions made by such model. High volume dust samplers were used to collect dust samples. Difficulties encountered in satisfactory dust sampling and quantification of results have been described.

Nov 8, 2011

By A. Warren Wilson, Hugh R. Wilson

This paper describes the evolution of the Waste Management Program at the Lupin Mine through the years 1982 - 1986. Echo Bay Mines' Lupin Mine is located on the western shore of Contwoyto Lake in Canada's Northwest Territories about 80 km. south of the Arctic Circle. The gold mine commenced production in 1982 and the Waste Management Program was based originally on the total containment concept. Due to an expansion of the mill circuitry and increased throughput, it was apparent that total containment was no longer applicable and therefore studies were undertaken to characterize the tailings, to evaluate the effectiveness of natural degradation of contaminants in the tailings pond and to determine what additional treatment steps would be necessary to meet the requirements of the mine's Water Licence. These studies indicated that arsenic and cyanide concentrations in the tailings pond decant water would not meet Water Licence discharge limits unless certain measures were under taken. As a result of this work, in late 1984 a decision was made to create a two-ponds-in-series system and the necessary civil work was started in 1985. In addition, a series of dykes were constructed to contain the solids portion of the mill tailings in a confined area of the first pond. To remove cyanide, the ponds are operated in a sequential fill and decant mode to take maximum advantage of natural degradation. For arsenic removal, a chemical feed system was constructed for iron salt addition to the decant stream from the first to the second pond. Decanting of the ponds is accomplished by means of a series of 500 mm (20 inch) Sclairpipe syphons.

Jan 1, 1987

By M Edgar, G Pattemore, M Auad, K Job, A Job, S Gale

In recent decades, significant advances have improved the modelling techniques for predicting slope failure. Predicting failures is vital in open pit mining due to the significant risk posed to personnel and equipment from unstable pit walls. Failures not only cause harm and damage to people and equipment but also cause delays to production and subsequently increase operational costs. Coupled with improvements in modelling techniques, utilisation of advanced scanning systems, such as high-definition imagery from UAVs has enabled faster and more precise mapping and modelling. However, one key element required for accurate slope stability modelling and monitoring is the ability for mine geotechnical engineers to have an accurate understanding of the mineralogy and moisture content of slopes, in real-time. To address this challenge, research has been undertaken to utilise hyperspectral imaging across a broad spectrum, combined with high-definition imagery, and LiDAR to scan slopes for minerals and moisture content. In addition to accurately mapping mineralogy and moisture, the data must be collected autonomously and remotely to ensure ongoing safety. The results show that there are many direct and indirect benefits from this new technology, including the ability to monitor slopes at a safe distance and in real-time, improved accuracy of modelling, detection of risks, and improving the automation workflow for geotechnical engineers. The paper presents recommendations for the implementation of the technology in open cut mining environments.

Jun 22, 2022

By B Stewart

It has long been recognised that knowledge of the conditions existing in a mine after an incident is essential in deciding whether to deploy responders as part of the incident recovery process. Applying this knowledge in a structured manner to the assessment and the acceptability of the risks likely to be faced by those teams during response activities before authorising their deployment is an onerous task incumbent upon the person controlling the incident response. The Mine Event Management System (MEMS) provides structure and coordination in the management of mine events. It assists with the skills and knowledge for incident control teams to effectively manage any emergency or non-emergency event, be it large or small. In cases where multiple organisations are involved, the MEMS promotes effective joint operations through the use of common terminology and structure to provide seamless communication between agencies at all operational levels. The SQL-based software developed by Queensland Mines Rescue Service (QMRS) assists decision-makers to make considered options; it does not make decisions for you. When set-up, it allows the information that already exists within a mine’s Safety Health Management System that is relevant to the incident to be accessed and considered rapidly within the pressured environment of an emergency. Additionally, the incident specific questions contained within MEMS focuses the management team on gathering and assessing information relevant to the incident as it progresses. The software’s event log can be utilised as an auditable document for post incident investigation. The MEMS provides a process to properly consider the adequacy of the information available upon which decisions have to be made, to consider and acknowledge the hazards of the environments within or adjacent to which responders will need to work and to acknowledge and authorise the entry of responders into or to remain within a mine either during or post an incident occurring, once an acceptable level of risk is achieved.

Apr 16, 2024

By James R. Hein

Barite and Fe-Mn-oxide deposits that occur along faults in the Southern California Borderland formed by low-temperature hydrothermal processes. The Borderland region consists of block-faulted continental crust within the broad transform boundary of the North American plate. The fault-bounded basins are anoxic and partially filled with hemipelagic and turbidite sediments. Barite was collected from four dredges and a submersible dive (DSV4-355) in the southern California Borderland, and was collected from two sea-cliff sites along the Palos Verdes Headlands near Los Angeles. Barite at these seven locations occurs along strike-slip and basin-margin faults from the shoreline to 1800 m water depth. Submersible observations showed a series of mounds up to 10-m high composed of friable, white barite associated with diffusely venting milky fluid; the mounds support large benthic colonies, including tube worms (Lonsdale, 1979). Barite samples recovered from dredges are brown, green, and white and range from porous, vuggy fragments to massive fragments cut by banded barite veins. Samples from two dredge sites contain fossil worm tubes 1-3 mm in diameter and >10 cm long. All the samples are nearly pure barite, with only minor to trace amounts of other minerals. Chemical analyses show 94-98 wt. % BaSO4, low total rare-earth element (REE) contents (<45 ppm), Sr contents from <2 to 10,000 ppm, and Hg contents up to 1 ppm. Chondrite and shale-normalized REE patterns show light REE enrichments and large positive Eu anomalies. These REE pattern characteristics are typical of marine hydrothermal fluids and minerals. Sulfur isotope ratios (d34SCTD) from +21.6 to +67.4? range from seawater values (+21?) to exceptionally high positive values. Strontium isotope ratios are lower than the modern seawater ratio as well as the seawater ratio that existed at the time of deposition of the host rocks.

Jan 1, 2002