Search Documents

By E. Zahl, J. Whyatt, H. Lawson

The U.S. Mine Safety and Health Administration (MSHA) issued Program Information Bulletin P09-03 in April 2008, providing formal guidance on using programs that model the redistribution of stress during underground mining of coal. A key part of this guidance is visual observation and mapping of ground conditions. If a correlation between ground conditions and model output can be established, the model is considered to be verified, and can be used to guide mine design in similar ground. A simple scale is recommended for ranking observed roof, rib and floor conditions. This paper discusses optimization and implementation of a ground condition rating scheme in the gateroads of a deep underground longwall coal mine. Roughly 80% of each gateroad length deteriorated in a fairly uniform manner. However, this manner varied between gateroads, as did pillar size. The implementation of a ground condition mapping program, similar to that recommended in PIB P09-03, was successful in characterizing the ground response to mining in gateroads of a longwall coal mine.

Jan 1, 2013

By H. Russell, N. DePriest, J. D. Quaranta

Valley-fill structures built of blasted rock overburden from Appalachian mountaintop surface mines pose many reclamation challenges. The steep mountainous terrain, short valley lengths, and straight stream channel profiles create significant challenges to implementing fluvial geomorphic landform design in terms of both form and function, and from a safety and constructability perspective. The fluvial geomorphic landform design approach balances erosive and resistive forces by considering long-term climatic conditions, soil types, slope profiles and vegetation types. Commercial geomorphic landform design software tools do not specifically analyze the stability and factor of safety for the computer-designed landform slopes. This research investigated slope stability parameters and factors of safety between a traditional valley-fill design with a geomorphic landform alternative. Slope stability assessments were performed on two profile geometries. Finite-element modeling of a permitted valley-fill and a geomorphic design alternative indicated that slope angle and internal angles of friction associated with the gradation of the overburden greatly affected the designed factor of safety for both designs. The geomorphic designed slopes yielded the highest factors of safety out of 14 models analyzed with all cases having factors of safety over 2.0. The high factors of safety are attributed to shallow slopes and beneficial surface and internal drainage.

Jan 1, 2014

By D. C. Dahlin

The Bureau of Mines has investigated podiform chromite deposits in three ultramafic bodies in the Caribou Mountain and lower Kanuti River areas of central Alaska. The investigation, reported in two parts, was done as part of the Bureau's mission to help insure an adequate supply of minerals to meet the Nation's needs. Part I describes an extensive field investigation and mineralogical studies by personnel from the Bureau's Alaska Field Operations Center. This report, part II, describes the mineralogy of 11 samples that were high-graded from surface exposures at 10 sites and presents the results of laboratory batch beneficiation tests designed to concentrate the chromite. The 11 samples, peridotites and chromitites that consisted of variable amounts of chromite or chromium-bearing spinets, olivine, and serpentine, were beneficiated by grinding and sizing, gravity concentration, and electrodynamic separation. Three high-chromium chromite concentrates, two high-iron chromite concentrates, and one high-aluminum chromite concentrate were produced. Three other concentrates were marginal, and two were submarginal. Chromium recoveries ranged from 54 to 92 pct. These results indicate that the areas may be significant chromium resources. Potential platinum association with the chromite was also investigated. Analysis of these 11 samples indicates that the areas are not good platinum resources.

Jan 1, 1983

By B Putland, I Lovatt, D Schwann, A Cervillin

The Mount Carlton project in Queensland's North East sits on a high-sulphidation epithermal style deposit rich in gold, copper and silver. Mt Carlton is an open pit mining operation with ore processed using a primary crusher, single stage SAG mill and flotation to produce a concentrate for sale. Orway Mineral Consultants (OMC) was involved in the original design of the comminution circuit and the project was commissioned in late 2012, with first concentrate shipped in March 2013. When Evolution sought to optimise the project in 2015, OMC was invited to assist by undertaking a circuit review to identify opportunities for the optimisation. During 2016, the Mt Carlton site team implemented the optimisation strategies developed in conjunction with OMC. These included reconfiguring the SAG mill discharge arrangement, reducing the average ball diameter and allowing the mill to operate at higher speed and under more autogenous conditions. Cyclone operation was changed to constant pressure and the vortex finder size was decreased. The combined strategies improved energy efficiency and allowed higher SAG mill power utilisation. The additional power has been used to increase throughput by 2.4 per cent while achieving a 27µm reduction in product size (P80) to gain downstream recovery improvements. The reduction in grind size has been achieved with only 6.8 per cent increase in specific energy consumption because of a 6.5 per cent increase in grinding efficiency. The circuit product size is also notably more consistent due to the improvements made to the cyclones, providing benefit to the downstream flotation circuit. A significant decrease in ball consumption was also gained, saving hundreds of thousands of dollars a year in operating cost.This paper will discuss the circuit design, start up and will detail the changes made during the optimisation and why these were successful.CITATION:Putland, B, Lovatt, I, Cervillin, A and Schwann, D, 2018. Mount Carlton comminution circuit design, start-up and optimisation, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 517–528 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By S. Shaw

There is an increasing requirement for mines to meet a certain minimum criteria for sustainability within the context of the physical environment, ecosystem and socio-economic system in which they are located. The mining industry has wrestled to develop methods for assessing the ‘sustainability’ value of a mining project and indicators of ‘sustainability success’. A methodology for the evaluation of sustainability of a mining project using the Multiple Accounts Analysis (MAA) system was developed. The MAA is a platform for engagement of stakeholders and for the assessment of site-specific alternatives based on both qualitative and quantitative indicators of success.

Jan 1, 2004

By R. Abel, T. Wildeman, N. Heflin

A study was conducted to assess environmental effects of waste rock piles on water in the Russell Gulch area. Each pile was rated on physical characteristics of proximity to an ephemeral gulch, extensiveness of erosion features, size, presence of vegetation, and presence of a kill zone. Chemical assessments focused on three leachate tests performed on waste rock samples. Ratings were based on pH, conductivity, acidity, and analysis for 31 metals using inductively coupled plasma emission spectroscopy. The chemical and physical assessment of each site is used to make a rating of each pile on its overall potential to deliver contaminants.

Jan 1, 2004

By A Coelho, D Bruce, H Grosser, C Parken, M Xia

Carrapateena is a new underground sublevel cave mine and was officially opened in 2020. It has a mine life of 20 years. Development began in 2016, and with the rare opportunity to start a with a blank canvas and having a long mine life, an effort was made to explore how to incorporate innovative and leading-edge technologies. The Ventilation on Demand (VoD) system was designed with the objective to optimise power consumption and ventilation delivery through the primary and secondary ventilation systems. Primary fans controlled by Variable Speed Drives (VSDs) and dualwinding secondary fans with multiple setpoints control the delivery of overall quantity. Automated butterfly dampeners control the regulation of air to individual production crosscuts, and automated louvres control the exhaust quantities from the mining levels. Ultra-sonic flow sensors are installed to measure air quantity and environmental stations are installed to measure air quality. Both are designed to play a key role in control and calibration of the system. It was quickly identified that no one vendor could provide a holistic solution to meet the design requirements. A strategy was derived to use multiple vendors, harnessing the specific strengths of each. A control system has been developed to allow the Site Operations Control Centre (SOCC) to oversee and control real-time delivery of ventilation as required by operations. The first full level installation of the VoD system was completed in September 2020.

Mar 15, 2021

By Richard Campbell, Claire Pirona, MEHMET KIZIL, Ismet Canbulat, Stephen Giese, Ravindu Goonawardene, Edward Steed, Serkan Saydam

The Australian longwall mining industry spends millions of dollars per year on proactive and reactive ground consolidation applications across most of the operations currently in production. The design and effectiveness of the applications and products vary widely and are based predominantly on-site precedence or what were considered successful applications at other sites in similar situations. In the continual improve the effectiveness of how consolidation products are used and when by enhancing our knowledge of the mechanical properties of products used in underground coal applications and applying this increased understanding to geotechnical design. One of the current challenges to further developing more appropriate and accurate geotechnical design methods for consolidation activities is the lack of standardised materials testing and knowledge of rock mechanics data on in situ performance. The lack of industry standardisadesign of consolidation programs, with a reliance on experience-based guidance for rockmass consolidation design. consolidation products. The program was designed to provide the industry with a set of geomechanical property index tests and a data set that can be utilised by rock mechanics engineers as baseline information for product evaluation and engineering design. The laboratory work undertaken is critical to understanding the exact small-scale mechanical properties of these products and testing was carried out at Monash University for various states of curing of each product. Recognising that the speed at which a mixed product develops its desired properties to act as a support element in underground coal mines is critical to its serviceability. This paper presents the testing rationale proposed, the testing results, and a framework for how the data set can be used to improve the engineering basis for ground consolidation design, in terms of expected rockmass performance under various mining conditions and application parameters.

Jun 25, 2024

By Dae Jin Ha

Sticking phenomenon occurring during hot rolling of two STS 430JlL ferritic stainless steels was analyzed by hot-rolling simulation tests. The sticking started from the initial nucleation stage in which the rolled materials were stuck onto the roll specimen surface, proceeded to the growth stage in which stuck fragments grew further, and reached the saturation stage. The modified 430JlL steel had a smaller number of sticking nucleation sites and slower growth rate than the conventional 430JlL steel because of higher high temperature hardness, thereby leading to less serious sticking. When the simulation test was conducted at 1070 °c, Cr oxides were formed on the surface of the rolled materials, and thus the sticking was drastically reduced because of the increased surface hardness of the rolled materials. In order to prevent the sticking, high-temperature properties of the rolled materials should be enhanced when rolled at 900°C or 1000 °C, and rolling conditions and alloying compositions, under which the oxide formation was promoted, were more important than high-temperature properties when rolled at higher temperatures than 1000 oC.

Jan 1, 2008

By Alfred W. Eustes III

The first of a series on the evaluation of rock cutting tools, this paper discusses the results of full-scale laboratory drilling tests that compare the performances of several polycrystalline diamond cutter (PDC) coring bits. The tests were performed in welded tuff as part of a site characterization program. Number of cutters, size of cutters, air course design, and other parameters were evaluated as they affect penetration rate, but this paper focuses mainly on the relationships of torque vs. thrust (weight-on-bit), specific energy vs. penetration rate, and thrust vs. penetration rate. These relationships change in diagnostic ways according to bit type, bit condition, and type of welded tuff.

Jan 1, 1998

By Paul H. Miller

After passage by the Congress, Public Law 95-87, the "Surface Mining Control and Reclamation Act of 1977" was signed by President Carter on August 3, 1977. This law, in its simplest form, was intended to control the environmental effects of surface coal mining and to ensure that mined land is restored to a condition equivalent to that prior to mining. Immediately after the signing, the wheels of government bureaucracy began turning to establish a new federal agency -the Office of Surface Mining Reclamation and Enforcement or OSM -in the Interior Department that would implement the provisions of the Act. Since this took time and because the Congress had not yet provided funding for OSM, a special task force was assembled within the Interior Department to begin the task of writing interim regulations to implement the Act. With respect to the use of explosives, the Act specified that a blasting plan be included in the application for a mining permit. The blasting plan will outline the procedures an operator will use to meet specified environmental protection performance standards. The performance standards established by the Act require explosives to be used only in accordance with existing state and federal laws and regulations and with regulations to be promulgated by the regulatory authority. The regulatory authority was defined as either a state agency operating under an approved state program or the OSM operating under a federal program. As a minimum, it was specified that the regulations should include provisions to require that: 1) a blasting schedule be published in a local newspaper and be mailed to local governments and to all residents living within 1/2 mile of the blasting site . 2) daily notice be given to residents in the area prior to blasting. 3) blast reports be prepared that are maintained for three years and available on request to the public. 4) blasts be designed to prevent injury to persons, damage to property outside the permit area, adverse impacts on underground mines and adverse effects on ground or surface water channels or availability outside the permit area. 5) upon request of residents or property owners within 1/2 mile of the permit area, preblast surveys shall

Jan 1, 1978

The design, specification, and performance evaluation of the Communications and Location portions of a Coal Mine Rescue and Survival System are described. The work was performed as part of a nine month effort to develop a mine rescue and survival system using existing technology and state -of-the -art hardware as recommended by the National Academy of Engineering. Three basic subsystems were developed, one for survival, one for communications/location and one for rescue. This report and related equipment manuals describe only the Communications/ Location Subsystem which was designed, fabricated, and tested by the Westinghouse Georesearch Laboratory in Boulder, Colorado. Two basic technologies were used. Electromagnetic signals propagating through-the-earth provide voice downlink and coded beacon up-link communications. Seismic methods were developed to provide means for locating trapped miners. Seismic signalling also provides a backup means for communications. Parallel development programs for the electromagnetic and seismic portions of the system were conducted. The resulting hardware and software have been partially tested in coal mines and under simulated emergency conditions in order to evaluate system performance. The results of these tests are discussed. Further testing is recommended in order to establish quantitative performance limitations tinder a variety of environmental conditions and to develop methods for improving system performance.

Jan 1, 1971

By Georgene Renner, Chee Theng, William Gleason

"With more than 900 booth spaces sold and 630 exhibiting companies displaying their wares, there was something for all 7,804 attendees on the exhibit floor of the 2015 SME Annual Conference & Expo in Denver, CO Feb. 15-18. The following is a sample of what was offered at the 2015 meeting.3D Laser MappingData collection and data analysis are changing how mining is done. One field in which technological advancements have made safer and more efficient operations possible is through site and slope monitoring.3D Laser Mapping, a United Kingdom-based company, was on hand at the 2015 SME Annual Conference and Expo to display its solutions for the mining industry, including its SiteMonitor4D system.The state-of-the-art laser measurementbased system was developed in partnership with geotechnical engineers and mining surveyors, and is a simple-to-use, reliable solution that has the flexibility and performance to function in a range of monitoring applications.The system measures and monitors the stability of rock faces, landslips and man-made structures, including ongoing, periodic measurement of volumes - stockpiles, cutbacks and waste dumps and has high-speed laser scanning for regular mapping of large areas by mounting the scanner on a vehicle.With specifications that other monitoring techniques cannot achieve, laser scanning opens up a new dimension in mine measurement and monitoring.www.sitemonitorsystems.comA.R. Wilfley and Sons Inc.Founded in 1919, A.R. Wilfley and Sons Inc. has been manufacturing dynamic-seal and static-seal pumps in Colorado for nearly 100 years, delivering its high-reliability, low-maintenance, heavy-duty process pumps and slurry pumps to the global mining industry. The family-owned company is now in the hands of the fifth generation."We are the dynamic-seal experts," regional sales manager Cesar Murillo said. "Most other companies are unable to do 100 percent dynamic seals and have to use mechanical seals or packing," he said, but Wilfley’s sealing technology does away with the need for mechanical seals and packing and their associated problems. As a result, solids and slurry handling capabilities are high, the pump can be run dry, and product dilution is eliminated. The pump can tolerate more misalignment, more cavitation, and more vibration in the pump during operation."

Jan 1, 2014

By Brian Rausch

Agenda ?? Refresher: Victor Project Execution ?? Operations Capability roadmap: ? Operations staffing starter group: design participation ? Operations staffing build up for production start-up ? Training and commissioning integration ? Turning OPSCAP ramp-up into a project ?? Go Live! The Results

May 1, 2009

By A. E. Lindquist

This Bureau of Mines publication identifies areas having sufficient coal reserves to support synthetic natural gas (SNG) development and summarizes those areas having the highest potential. Capital requirements, mining and coal cost factors, water availability, and coal-quality data pertinent to SNG production are presented. Evaluation of individual coal reserve blocks was based upon coal and water requirements of the Bureau of Mines Synthane coal gasification process.

Jan 1, 1977

By Ronald B. Stotelmeyer

This report summarizes the U.S. Bureau of Mines evaluation of the mineral resources of eight roadless areas in several National Forests in Montana. The areas are amoung those that have been proposed as additions to the National Wilderness Presevation System In various sessions of the U.S. Congress. Mineral Commodities present include gold (lode and placer), silver, copper, lead, zinc, molybdenum, tungsten, rare-earth elements, fluorite, and barite. Numerous mineral deposit types occur. Past production was from gold placers and vein-type deposits. There is potential for development of large volume porphyry copper-molybdenum, disseminated gold, stratabound copper-silver, and exhalative massive-sulfide metallic deposits. A substantial increase in metal prices is needed before any known vein-type deposits will be economic.

Jan 1, 1994

By R. Larry Grayson

In the October 1998 issue of the Holmes Safety Association Bulletin, NIOSH authors Mark Stephenson and Carol Merry wrote the article Hearing loss among miners and measures to protect hearing, which focused on the extensiveness of hearing loss among miners and the use of hearing protection to prevent hearing loss. While the primary importance of engineering controls in preventing hearing loss was discussed, since miners do not generally have control over their work en­vironment or assignments, the article focused on the importance of consis­tent use of hearing protection. In this article, all aspects of a compre­hensive approach to the prevention of hearing loss in miners will be covered. The discussions will do the following: ? describe application of the hierarchy of controls in preventing hear­ing loss in miners, ? give an example for each type of control measure and its impact, ? explain the major provisions, be­yond the hierarchy of controls, of the recent NIOSH document en-titled Criteria for a Recommended Standard: Occupa­tional Noise Exposure, Revised Criteria 1998 relative to a hearing loss prevention program, and ? summarize important points on control of noise exposure for every miner to remember, equipment in most facets of operations. Miners are well aware of noisy areas in or around equipment, icluding extraction machinery such as draglines, power shovels, longwall shearers, and continuous mining machines; powered haulage equipment such as load-haul-dumps, shuttle cars, large trucks, and continuous haulage units; roof bolting machines; jackleg drills and stopers; auxiliary equipment such as compressors, fans, and pumps; size reduction equipment, etc. They are not well aware of the insidious nature of pro­gressive hearing loss, which is per­manent, but they are generally aware of what levels of noise are hazardous and what measures can be taken to reduce their personal noise exposure. Behaviorally, however, there are many reasons why miners choose not to use hearing protection faithfully.

Jan 1, 1998

By P. R. Taylor

This investigation (Bowles, 1990) involves consideration of technology utilized by three separate fields of metallurgy and materials science: 1) The recovery of metals employing the use of solvent extraction, 2) The fabrication of materials using powder metallurgy, and 3) The use of composite materials in fabrication of engineering materials. The research considers each of the processes in order to realize the benefits of each. In light of the fact that materials have an intended use -it does seem plausible to simplify the process required between "mother earth" and final use. For instance, a primary copper producer that already employs a solvent extraction and electrowinning process could produce value added products directly. Part of the existing extractant flow could be diverted into a pressurized hydrogen stripping process in order to produce specialty composite powders. Innumerable methods have been employed for the recovery of metals; solvent extraction, the one considered in this study, was used due to the possibility of it providing a pure powdered metal. The use of solvent extraction in the recovery of metals has gained wide acceptance and its use proves beneficial in many applications (Ritchey and Ashbrook, 1984). Pressure hydrogen stripping of solvent extractants may provide the benefit of flowsheet simplification compared to conventional solvent extraction followed by electrowinning. It may also provide the benefit of direct production of high purity metal powder (Demopoulos and Distin, 1985).

Jan 1, 1992

By B L. Sainsbury, M F. Lee, A Penney

For most practical rock engineering purposes, stress versus strength conditions around underground openings for which rock masses fail and their various modes of failure, are reasonably well-understood and predictable. Some rock masses and particular rock types fail slowly and relatively quietly. However, others can fail rapidly, violently and maybe with the ejection of significant broken rock. In some countries and in some mines, the latter style of violent fracturing and failure of the rock mass is referred to as ‘strain bursting’. It can be alarming and extremely hazardous to nearby miners and machines. For such situations, the design and installation of appropriate ground support, to provide a safe work place, can be challenging. At any particular mine site, it’s often generally understood which local rock masses (rock types) are prone to strain bursting. Competent and strong siliceous rocks and some massive sulphides are often the main offenders. While some neighbouring, equally-competent and strong rocks might also fail, they do so more quietly and without ejection. To understand this contrast, a better understanding of the fracturing process is required other than simple and standard strength versus stress considerations. Suites of standard intact rock properties from numerous Australian mines have been used to define and help understand different high-stress failure styles for component intact rock; especially those prone to violent fracturing (strain bursting). Simple considerations of micro-fracturing (defects in the intact material), plus the available energy at failure versus the energy consumed during fracturing, distinguishes between over-stressed and competent rock types that fracture violently and those that don’t. CITATION:Lee, M F, Penney, A and Sainsbury, B L, 2018. Proneness of competent over-stressed intact rock to violent fracturing, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 170–184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M. Z. Naghadehi, F. F. Nasategay, J. Sattarvand, R. Battulwar, E. E. Gohari

After the recent increase in catastrophic failures of tailings dams such as the Burmadinho, Brazil failure in 2019, the mining industry has actively engaged in the stabilisation of tailings dams. Most of the tailings storage facility (TSF) guidelines suggest a laborious action that can be facilitated through imaging by unmanned aerial vehicles (UAVs). Although UAVs are not unknown to most mining operations, automated rill detection through aerial image processing is a new concept. This study utilises images from sites in the U.S. and employs semantic segmentation with a UNet architecture to detect location and size of these rills. The developed model can be used as a tool for monitoring surface erosion of TSFs.

Sep 1, 2021