Search Documents

By Martin G. Wafforn, George J. Greer

"In early 2014, Pan American Silver Corp. commenced a project to construct a second shaft at its La Colorada underground mine located in Zacatecas State in Mexico. This was the first new shaft development project undertaken by Pan American Silver in the history of the company. The existing mine workings permitted the use of a raise bore for the excavation of the shaft opening, utilizing directional drilling in poor ground conditions to advance the pilot hole. This was an interesting project with many challenges and successes, and numerous lessons learned. The project was successfully completed in 2016, with the shaft operating at full mine production capacity within weeks. INTRODUCTION The La Colorada Mine has a long history dating from at least the 1920’s. The mine is located in the northern portion of Zacatecas State in Mexico in the Chalchihuites area, an approximate two hour drive south from the city of Durango. Pan American Silver acquired the La Colorada mining concessions in 1998, with mine production at that time consisting of only a few hundred tonnes per day. Over the course of the following 15 years, with the addition of an oxide processing plant and some expansions to the sulphide processing plant and site infrastructure, production was eventually increased to a maximum of 1,250 tonnes per day, all of it generated from conventional cut-and-fill stopes in the underground mine. An existing shaft was used to hoist the ore to surface, and over the years Pan American Silver had deepened the shaft and had changed out some of the hoisting plant. However, there were historic workings in close proximity to the shaft that made it unsuitable for personnel transport, and shaft maintenance was becoming difficult. The shaft was increasingly considered as a risk to the long term production continuity, and also to further deepening of the mine. In addition, expanding the capacity of this old shaft was not possible. Drilling of the La Colorada mineralization at depth commenced in 2010, with very good exploration success. As a result, by the end of 2013, the mine reserves had grown to a total of 6.5 million tonnes of high grade ore (388 g/t Ag, 0.36 g/t Au, 2.4 % Zn, and 1.3% Pb). Furthermore there were more (and higher grade) sulphide reserves than oxide reserves at depth. Following the completion of an internal study in 2013 with assistance from one of the international shaft contractors, a decision was made to increase the production from the mine with the construction of a new shaft and a new sulphide processing plant, a project with a calculated payback of 2.2 years."

Jan 1, 2019

By Lance Rasband, Richard Hanke

"Seattle Tunnel Partners (STP) started mining on Seattle’s SR99 tunnel on July 30, 2013, working slowly through a 15 ft (4.6 m) thick fiber-reinforced concrete headwall. Once through the headwall, the machine would move through roughly 400 lineal ft (122 m) of jet grout-improved soil at a rate slightly over 6 ft (1.8 m) per day. It was anticipated that once through the improved area, Bertha—the world’s largest tunnel boring machine—would move at a rate of 35 ft (10.7 m) per day. By the end of October 2013, Bertha had mined roughly 430 ft (131 m), averaging 4.73 ft (1.4 m) per day, and had begun mining within native soils. By the start of December 2013, tunneling reached the 800 ft (244 m) mark and Bertha averaged 12 ft (3.7 m) per day, achieving as much as 42 ft (12.8 m) of progress on some days. However, on December 6, 2013, Bertha began to stumble and all progress quickly came to a halt. Preliminary InvestigationInitial reports stated that an obstruction had stopped the machine in its tracks. Malcolm Drilling received an early morning call on Sunday, December 8, 2013, from STP to rapidly mobilize a Bauer BG-50 drill rig with crews to investigate what was hindering Bertha’s progress. Malcolm’s equipment and crews flew into action and were completely mobilized and operational by mid-week. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic head within the ground around the machine and allow STP personnel to inspect the cutter head from within the shaft for presence of obstructions. By the close of December 2013, the wells were installed and the dewatering system was fully commissioned. STP crews were then able to inspect the cutter head and found small fragments of a steel pipe wrapped around the outside of the shield. The steel was apparently from an abandoned 10 in (0.25 m) diameter monitoring well casing previously installed by WSDOT (Washington State Department of Transportation) to monitor groundwater conditions for the design and planning of this very project. After the steel was cut out of the head and cleared from Bertha’s path, she attempted to move forward but was only able to manage a slow crawl"

Jan 1, 2015

By D. McCarthy

This paper discusses the process involved in developing an optimum method of treating and removing heavy metals from water that have leached out from the native rock -prior to discharge back into the environment. Also designed into the system is a manner to stabilize the metals removed as a precipitate, so that they can be disposed of as a non-hazardous waste.

Jan 1, 1992

By S Cyphers, J Missen, B Jansen

The AGL Loy Yang Mine is one of the largest and most significant coalmines in Australia. Commencing in 1982, this mine produces 30–35 Mt/a to supply more than 50 per cent of Victoria’s electrical power requirements. At this mine there are unique geotechnical challenges to overcome to ensure its safe operation including: significant mine depth, low density of coal in the operating and permanent mine batters, the influence of groundwater and deep sediment aquifer pressures. One of the challenges is the behaviour of brown coal, which is neither a soil nor a rock and displays long-term creep stress relief. Other geotechnical challenges include ensuring stability in high unconsolidated dumps, potential large-scale block movement in mine batters driven by crack water pressure and heave from high-pressure aquifers.The paper will outline the geological and hydrogeological setting and potential failure mechanisms, and detail an integrated geographic information system and reporting regime that in part addresses ground control management at the mine. The paper will also outline the management processes for a dynamic geotechnical environment and the benefits of the alliance arrangements to meet the geotechnical requirements at the mine and the effective personnel integration in the mine technical services team.CITATION:Jansen, B, Missen, J and Cyphers, S, 2014. Geotechnical management at the AGL Loy Yang Mine, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 239–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Ken Goering, Steve Kral, William Gleason

"Once every four years, the global mining industry gathers in Las Vegas, NV for MINExpo International. According to the show’s organizer, The National Mining Association (NMA), about 44,000 people attended the three-day show from Sept. 26-29. It was a show that featured the latest and greatest in equipment and technology. It also served as the backdrop for a snapshot of the state of the industry and while the picture of a global industry is never completely clear at any one time, one thing that is evident is technology has become a major force in the way mining is done.Had it not been for the awe-inspiring “iron” that was on the show floor in the form of haul trucks and shovels weighing hundreds of tons, one could be forgiven for thinking that they were at the Consumer Electronics Show. From training simulators designed to give a realistic experience of operating mining equipment to virtual reality technology that can take the user into the depths of an underground mine or the middle of a mapped ore deposit, an overriding theme of MINExpo 2016 was that the mining industry is connected like never before.In the north hall of the Las Vegas Convention Center was the GE Mining booth that was designed to showcase its efforts to help create a mine that will be connected from the front office to the face of the underground wall or bottom of the openpit. GE Mining called its booth a digital mine, and it included a suite of technologies that can improve performance, reliability, safety and operations. GE Mining said it views each mine as a mini-city, requiring power, water and transportation. Intelligent, real-time monitoring across the mine allows operators to make data-driven decisions that improve equipment reliability and optimize mine operations for substantial savings. And GE Mining was just one of many exhibitors showing off software that allows various types of equipment to communicate. Its booth sat in the shadow of the Komatsu booth with its new 360-t (400-st) 980E-4 haul truck that included GE’s 360-t (400-st) electric wheel motor. This is just one example of how technology is connecting machines, operations and people around the world and how mining is moving forward."

Dec 1, 2016

By A. R. Laplante

Gold recovery early in the flowsheet, typically from the primary grinding circuit, has seen significant advances in the past three years. Some of the advances achieved under the auspices of the AMIRA P420B Gold Processing Technology project are reviewed. The areas covered are gravity-recoverable gold (GRG) characterization, GRG behaviour in classification, gravity recovery simulation and the link between gravity recovery and cyanidation.

Jan 1, 2005

By G Britton, P Moynagh

As more than a few mines gradually sink under the weight of emails, whiteboards, notice boards and ever more complex spreadsheets, the holy grail of effective short-term interval planning and control in underground mines is as far away as ever. Despite the mining industry investing ever greater amounts in planning and Enterprise Resource Planning systems, short-term plans become ever more complex and rigid. What the industry desperately needs are not more ‘disembodied voices down the speaking tubes’, but flexible and effective planning systems that encourage people to make reasonable commitments to each other so that everyone can work as a coordinated team to complete the work required each shift.One solution to the challenge has emerged. This paper describes the ‘Fewzion’ shift planning and short interval control system which has been developed at Anglo American’s Moranbah North and Glencore’s Oaky Creek coalmines in Central Queensland. Fewzion has drawn on management theory embodied in Management Operating Systems, Lean and Theory of Constraints approaches to continuous improvement to play a key role in both mines achieving record breaking tonnages.In addition to explaining the Fewzion approach, a case study is presented describing how Anglo American’s Moranbah North improved production by 39 per cent in 2014/2015 and won ‘Coalmine of the Year’ two out of the last four years and how Glencore’s Oaky Creek sustainably improved monthly development meters by 34 per cent within two months of implementing Fewzion.CITATION:Moynagh, P and Britton, G, 2017. How a frontline planning and commitment system improves trust, commitment and results in operations, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 235–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By I R. F MacCulloch

Bacterial oxidation of sulfide minerals is a familiar and commercially available process to enhance gold recovery with problem ores. Pintail Systems, a Colorado, USA based company had developed bio-processes for gold recovery based on natural mineral formation and transformation in a global mineral cycle. The biological recovery of precious metals from ore involves a number of mechanisms that are dependent on the metal-mineralogical association. These processes include: partial bio-oxidation of sulfide ores; oxidation of gangue minerals exposing gold to leaching; surfactant properties of bacteria/nutrient solutions that improve wettability of ores and solution contact with leachable gold and silver; and microbial production and excretion of trace amounts of gold lixiviants, and bio-fracturing or biological alteration of ore minerals. Pintail has demonstrated enhanced recovery of precious metals during cyanide detoxification of spent heaps at the end of mine life. Biological recovery processes also have the potential to be applied to in situ mining technologies. The in situ process application could recover gold from subgrade deposits, small deposits or those ore bodies with uneconomic stripping ratios for conventional mining. In situ biomining can be accomplished at a fraction of the cost of conventional mining and leaching and does not have the environmental liabilities associated with many conventional gold lixiviants.

Jan 1, 2004

By Lloyd Buckingham

Barrick Gold Corporation (Barrick) has undertaken innovative methods of evaluating and improving the performance of grinding mills in several of its operations around the world. The results have been positive with some of the mines showing more than 20% net energy improvement leading to more than 43,000 tonnes per year reduction in CO2 emissions in four of the operations reviewed.

Jan 1, 2012

By J. Cayouette, . Blatter, P. Cousin

The Laronde mill was commissioned in 1988 and has been treating the Laronde Perim ore since 2000. The Laronde plant, situated in the Abitibi region of Quebec, has experienced mill expansions to accommodate 7500 mtpd and to recover gold and silver as well as important amounts of base metals (Cu, Zn, Pb). Ten sequential metallurgical and environmental processes are responsible for metals recovery and process viability. Over 200,000 ounces of gold, 4,5 million ounces of silver, 7000 tonnes of copper, and 78,000 tonnes of zinc are produced annually. In 2008, the Goldex plant began trucking high wade (35-45 Wt Au) pyrite sulphide concentrate (TCGO) for gold extraction at a newly constructed treatment plant, increasing gold output at Laronde by 40,000 ounces. In 2009, the high gold wade Lapa ore processing facilities were annexed to the Laronde plant increasing output by 120,000 ounces of gold. TCGO and Lapa productions are forecasted until 2018 and 2015 respectively, with known reserves of each mine. Today, up to 140 permanent employees run and optimise the Laronde plant operation. As a result, Laronde has intricacies intrinsic to a large and varied operation. The paper will outline the metallurgical highlights, challenges, and future outlook related to the treatment of each ore type (Laronde, TCGO, and Lapa)

Jan 1, 2011

By Daniel Stevenson, Richard Guenther

"The preservation of historic buildings is not only essential to the understanding of our national heritage, but it is also environmentally responsible to adapt existing buildings to compatible new uses. With this perspective, the American Enterprise Institute began exploring options to expand the newly acquired Andrew Mellon Building, located at 1785 Massachusetts Ave. NW in Washington, D.C., without causing any harm to the Beaux Arts style limestone façade and its plaster interiors. The building is a National Historical Landmark, but its 72,000 sq ft (6,690 sq m) of usable floor space did not meet the needs of its new owner. The building perimeter is very near the property line, so horizontal expansion was not possible. Adding height to the building was not an option, as this would have altered the historic nature of the building exterior. The only feasible option that could provide the desired floor space was to add a new floor underneath the existing structure. By adding a level beneath the existing building, an additional 28,000 sq ft (2,601 sq m) of floor space could be produced.Berkel & Company Contractors was chosen as the deep foundation/shoring contractor tasked with ensuring that the existing structure was stable and remained undamaged during the excavation and construction of the new lower level. To accomplish this, Berkel provided a shoring system that would act as both excavation support and permanent deep foundation elements for the final structure.Preservation of the existing limestone façade and plaster interiors was critical to the success of the project, as additional foundation settlements could damage these irreplaceable building components. Project specifications, therefore, included very stringent limits for foundation settlements. The maximum allowable total settlement for all existing building walls and columns was ¼ in (6 mm) for the duration of the project."

Jan 1, 2017

By Casters B. Foster

The U.S. Department of Energy has undertaken, in a cost sharing partnership with industry and utilities, an extensive coal-oil mixture (COM) combustion program in a number of promising applications. One of these is the injection of COM through tuyeres into a blast furnace in lieu of oil. From work done previously, it has been established that COM can be burned in existing oil, fired facilities. The issues being addressed by the current DOE program are: 1) determination of best available technology to achieve environmentally acceptable operation, and 2) determination of applications for which COM can be utilized economically.

Jan 1, 1978

By Douglas Rudenko PG, Jay Elkin, Siavash Mahvelati Ph. D.

Very little studies have investigated the behavior of cracks in unlined tunnels over long periods of time, especially when such flaws are subjected to blast-induced vibrations. Using a pool of 30+ blast events, a positive correlation was found between the peak particle velocity and peak crack movement.

Feb 1, 2020

By D. Parks, A. Miller, M. McNinch, R. Jacksha

Each year, hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s two phase implementation of an IoT-based intelligent machine monitoring system. Phase one is the installation of a proof-of-concept system at a concrete batch plant, while phase two involves scaling up the system to include additional sensors, more detailed safety/performance metrics, proximity detection, and predictive failure analysis.

By David P. Kimball, Dalva L. Moellenberg

On May 21, 1990, EPA released its Strawman II draft program for mining wastes. It proposes to expand RCRA regulation of mining operations to include materials other than wastes. Strawman I1 would establish strict standards for the states to follow, rather than technical guidance. It proposes to establish performance standards; design criteria; monitoring requirements; and corrective action, closure, post-closure, and financial assurance requirements. It suggests "pollution prevention" concepts for mining operations. This paper explores the Strawman II proposals, particularly the technical criteria, and addresses several of the important concerns raised by industry.

Jan 1, 1991

By Daniel Roy, Danielle Bouffard, Antoine Berton, Simon Gariépy

Commissioning a mineral processing plant has always been a challenging task. The process includes pre- operational verification, dry and wet commissioning, and a gradual ramp-up to full production, all of which must be executed within the shortest possible timeframe, requiring numerous highly interdependent tasks to be conducted concurrently. This phase is under scrutiny by shareholders, corporate management, and other stakeholders who are keen to see a return on investment as the operation starts yielding results. Despite extensive documentation in the literature highlighting its significance, the impact of the commissioning phase remains underestimated in contemporary mining projects. This paper provides an overview of the commissioning process and its associated challenges before focusing on a critical success factor: building a dedicated commissioning team with the required competencies and personality profiles. The roadmap to achieving an efficient plant start-up is outlined. Drawing on over 15 years of experience with more than 20 concentrator commissioning and start-ups, a general framework is presented to maximize success. This method emphasizes the crucial role of the operation and metallurgy team in supporting these projects. Finally, insights from Soutex’s involvement in multiple start-ups are shared, offering lessons learned that emphasize best practices and challenges encountered in expediting the ramp-up process while maintaining high Health, Safety, and Environment (HSE) standards.

Feb 1, 2025

By Jed Greenwood, Lyall Workman, Michael Haggerty, Russell Sheets

Draglines often work from a position on the active highwall or spoil side bench to remove undisturbed waste material and spoil in the previously mined pit. To protect the dragline crew members and the machine, it is necessary that the highwall remain stable while the dragline is present on the bench. In the past several years, we have been involved in determining the causes for highwall failures that included the dragline. While there have been no injuries and limited dragline damage with these incidents, the potential certainly exists for a more serious outcome. In all cases, the operation had completed a geotechnical study to support the ground control plan and pit designs. However, all these incidents included aspects that would not likely have been identified in studies to determine highwall and spoil designs to support ground control procedures. In general, these events included aspects that were localized and would have been difficult to identify in initial slope stability studies either observationally or during the soil testing and modelling efforts. Although the authors do not have quantitative evidence of this, it does seem there has been an increased number of events in recent years. This may be due to loss of institutional knowledge, mining in more challenging areas, or simply an increase in localized variation. This paper will describe some of the issues we have seen and what the causes of failure were. It becomes clear that avoiding similar incidents in the future requires on-going observation and inspection of active highwalls and spoil benches to try and identify local variability and impact on mining. The information can proactively be used to update stability modeling of any concerning issues to determine likelihood of problems and to develop solutions.

Feb 1, 2025

By Tim Lundquist

Disa Technologies Inc. provides innovative, sustainable solutions for mineral processing and remediation through its patented High-Pressure Slurry Ablation (HPSA) technology. HPSA processes solid feed material in slurry form, propelled by high pressure pumps through opposing nozzles that generate impinging jets within a collision housing. This process induces particle-to-particle collisions in a high energy zone, creating intergranular fractures along grain boundaries. In our batch scale and continuous operating testing, we have found that controlling key processing variables such as nozzle velocity, slurry solids percentage, and the number of passes can allow for controlled size reduction and maximum mineral liberation. Since 2018, Disa Technologies has demonstrated the versatility of HPSA by testing it on diverse materials, including phosphate, copper, uranium, vanadium, zinc, rare earth elements, lithium, nickel, mineral sands, gold tailings, and more. The intent of this paper is to present an overview of our test results describing in detail impacts on size reduction, recovery, and grade with a focus on HPSA's adaptability across ore types. Looking forward, it explores the potential to process materials such as DR-grade iron, clay, PGMs, bauxite, and various tailings. Additionally, it examines planned advancements in HPSA technology, including optimized nozzle spacing, higher capacity models, improved tonnage-to-footprint ratios, enhanced maintenance features, and expanded nozzle configurations.

Jan 1, 2025

By Yuting Xue

Classification of rock and coal is one preliminary problem for fully automated or intelligent mining. It assists in automated rib stability analysis and enables the shearer to adjust the drums without human intervention. This paper studies the classification of rock from coal on rib images using machine learning techniques. A database of rock and coal images was created by filtering photographs taken by NIOSH researchers during site visits. Machine learning was conducted on patches, smaller images randomly extracted from each rock or coal image. After training, the classifier was validated with the testing dataset and achieved an accuracy score of 0.9.

Jan 13, 2022

By Ron Stewart, Richard Youmaran, Andy Adler

In the current context of heightened concerns with explosives security, there is significant interest in technological controls to improve security. It is important to be able to control what is fired, by whom, where and when. This paper describes research Orica has performed to investigate and test biometric systems to address the question of "by whom". The goal of this research is to incorporate the most suitable biometric system onto the 'blaster' unit of an electronic initiation system. This approach will ensure that only authorized personnel can initiate a blast involving electronic detonators. Requirements analysis: we initially explored many different biometric technologies to evaluate them against the requirements, including security, usability, ruggedness, size, form factor, privacy, and operational temperature range, This analysis identified chip based fingerprint sensors as the best candidate. Development of prototype units: in order to test the identified sensors, we modified standard, commercially-available, electronic blast initiation units ("blaster") to incorporate a fingerprint reader. Testing and evaluation: Biometric We conducted a biometric scenario evaluation in order to determine: 1) security level (measured by false accept rate (FAR)); 2) usability (measured by failure to enroll (FTE) and false reject rates (FRR)), and to 3) discover environment specific issues and challenges (such as temperature, humidity, dirt, or those related to the usage patterns of the user group). Tests were conducted at quarry sites in eastern Ontario, Canada. Results show rates of: FAR= 0%, FTE= 1.67%, FRR= 28.81%. Overall, these results suggest that this fingerprint biometric technology has a good level of usability in this application of electronic blast initiation control.

Jan 1, 2007