Search Documents

By Bruce Macdonald

Operational monitoring of slope stability can be achieved by space based InSAR monitoring platforms. Natural and man-made rock slopes are monitored using a novel stack-based InSAR method that exploits both persistent point scatterers (PS) as well as coherent distributed scatterers (DS) such as areas of pavement and sparsely vegetated surfaces. The new method, Homogenous Distributed Scatterer (HDS)-InSAR identifies InSAR targets by using adaptive multilooking of statistically homogenous pixel neighbourhoods combined with thresholding the differential temporal coherence of each target candidate with respect to its surroundings. HDS-InSAR preserves PS and therefore forms a direct generalization to our proven DualScale-PSI method. The density of HDS exceeds that of PS by more than an order of magnitude often providing essentially continuous coverage over urban and industrial landscapes featuring a mix of infrastructure with mostly bare soils or rock surfaces. The improved coverage enables better definition of surface motion and underlying geology, which will lead to superior interpretation of the geophysical mechanisms causing the surface deformation, e.g. through improved integration with 3D deformation modeling. We illustrate the performance of our new HDS-InSAR method compared to DualScale-PSI using displacement results from Vancouver, Canada; Bingham mine, USA; and the Palabora mine, South Africa.

Jun 1, 2012

By J. Ouellet

The authors participated in a study for a new mine shaft in Saskatchewan?s Athabasca Basin where ground freezing is desired to reduce water inflows. Constraints were imposed on the design in terms of permissible water leakage (less than 10 m3 / hour) inside the shaft. Since the shaft goes through highly permeable formations, water control measures had to be incorporated into the design. Ground freezing was selected as the most reliable and proven method for the sinking and a hydrostatic liner design was implemented. While exploring various technological options available for providing a fully hydrostatic liner, the authors came up with a new design concept that offers a more cost effective solution while meeting all the design constraints. The new liner concept is a composite design using concrete and a sprayed-on membrane system. A proof of concept program comprising laboratory testing and field testing was successfully implemented. This paper presents the innovative liner design, as well as the adapted sinking methodology, developed for this type of project. The new concept offers a new cost effective high performance hydrostatic mine shaft liner comparing favorably with traditional methods. RESUME: Les auteurs ont réalisé une étude pour un nouveau puits de mine dans le Bassin de l?Athabasca en Saskatchewan. Des limites sévères sont imposées sur le design en terme de volume d?infiltration d?eau acceptable (moins de 10 m3 / heure). Comme ce puits de mine traverse des formations très perméables la congélation des terrains a été sélectionnée, une méthode éprouvée et fiable. Un design hydrostatique a été choisi pour le revêtement du puits. Dans le processus de design, les différentes technologies disponibles ont été étudiées. Les auteurs ont développé un nouveau concept de revêtement composite offrant un rapport performance/prix plus avantageux que les technologies conventionnelles. Le nouveau design proposé est composé de béton et d?une membrane projetée. Un programme expérimental a été réalisé pour démontrer la faisabilité du concept. Cet article présente le nouveau concept ainsi que la méthodologie de fonçage de puits adaptée. Ce concept innovateur offre un revêtement hydrostatique performant à un cout avantageux par rapport aux techniques de construction utilisées jusqu'à maintenant.

Jun 1, 2012

By M Salu, G J. Kay

"As underground mines increasingly face the challenge of maximising production without losingfocus on safety excellence, the ability to predict the eff ectiveness of mine seals and stoppings andthe identifi cation of defects plays an increasingly important role in mine ventilation management.While technologies for sample testing installed seals provides signifi cant assurance, the difficulty of conducting tests in operational environments, combined with the production impact of destructive testing procedures, has led to the development of a new method for non-destructively testing ventilation control devices (VCDs). This paper addresses the challenges of in situ testing and reviews the approaches previously employed to verify the quality of VCD installations. It then describes a new testing methodology jointly developed by Whitfield Minerals PTY Ltd and Parsons Brinckerhoff (PB) and the range of tests that have been carried out in the laboratory, above ground, at trial underground sites and in active coal mine operations. Although this is a new approach to testing underground VCDs, the method employs recognised testing equipment in a new application. The aim of the new non-destructive technology is to not only verify the thicknessand therefore overpressure rating compliance, of new VCDs, but to allow mine operations t oidentify and locate defects in installed VCDs without causing damage to the material structure.Currently it is difficult, time-consuming and costly to carry out physical sampling and testing ofevery VCD. Therefore, a reliable and accurate means of non-destructively testing concrete andplaster seals in situ will provide substantial operational and safety benefi ts to the underground coal mining industry."

Jun 1, 2012

By Hamidreza Soltanzadeh

The injection of CO2 into a reservoir or aquifer can potentially result in deformation, induced fracturing and fault reactivation in the injection zone and/or the rocks that surround it. This paper reviews the data collection and geomechanical analyses performed to assess these potential hazards for the Heartland Area Redwater Project (HARP), in which CO2 sequestration is being considered in a carbonate (Leduc Formation) reef. A three-dimensional mechanical earth model (3D MEM) was developed using available geophysical log data from several wells. The geomechanical response to CO2 injection was studied using a finite element numerical model based on the 3D MEM and pore pressure distributions predicted using a reservoir simulator. The modeling results suggest that the potential for induced fracturing and fault reactivation is low and the maximum predicted ground surface heave is less than 2 cm. Sensitivity analyses conducted with a 2D geomechanical model that was extracted from the 3D model confirm that this conclusion holds true even when a reasonable measure of uncertainty in rock mechanical properties, ambient pore pressures and horizontal stress magnitudes is accounted for.

Jun 1, 2012

By D Cliff

"It has been 17 years since the mine disaster at Moura No 2 Mine in Queensland. Recent disasters in the USA and New Zealand prompt the question what has changed since 1994. This paper att emptsto answer this question and identify areas that need improvement."

Jun 1, 2012

By Karina Forster

Open stope design depends on the ore body geometry, loading conditions and rock mass properties to estimate stope dilution and ground support requirements. Rock mass conditions for design primarily rely upon estimates of well established rock classification systems. Many sources of data exist for obtaining estimates for these rock mass classification values which include core logging, geotechnical mapping, geological mapping as well as linking one classification system to another through the use of empirically derived equations. The extent of mapping coverage can also vary significantly based on the data collection technique. This paper proposes an approach where individual components of rock mass classification systems are collected by the different available data collection techniques. Data from different rock types are also considered separately based on their alteration characteristics and general observation products. Data from the Cameco Corporation Eagle Point Mine is presented and an approach is outlined for obtaining average representative classification values for stope hanging wall characterization. The effectiveness of this approach is demonstrated through the analysis of a data base of hanging wall dilution information.

Jun 1, 2012

By B Beamish

"All underground coal mines in Australia are required to develop a Spontaneous CombustionManagement Plan (SCMP). The New South Wales Government has developed a guideline (MDG1006) to assist operations to comply with this requirement. A reference document is alsosupplied with the guideline that describes the type of information that is needed for input to theplan, including identifying possible tests that can be used for propensity assessment. However,there is no clear indication of what program of sampling and testing is suffi cient to provide adefi nitive assessment of spontaneous combustion propensity prior to and during mining. This paper reviews the existing methods available for quantifying spontaneous combustion propensity and discusses the sampling requirements that are needed from exploration to mining. A new, more defi nitive method of spontaneous combustion testing is also presented that benchmarks coal self-heating performance from mine ambient temperature to thermal runaway. Examples of the eff ectiveness of this new test method for identifying and quantifying reactive pyrite in coal as well as quantifying the diff erence between dry and wet season conditions are provided in the paper."

Jun 1, 2012

By M Ogle

"Booster fans are relatively rare in Australian coal mines. However, as mines become progressivelydeeper it is likely that such fans will be increasingly adopted as a method to sustain or improve the ventilation of underground workings. The reasons why booster fans may be an att ractive alternative include: increased cost of sinking additional ventilation shafts with greater seam depths; environmental objections to shaft sinking projects; and increasing urbanisation and surface constraints limiting availability of potential ventilation shaft sites. As Tahmoor Colliery movedinto its northern lease the ventilation constraints became the limiting factor on production. Thelimitations of the old workings meant that the existing ventilation system would be inadequateto sustain the required production. Extensive ventilation modelling was carried out to evaluatevarious potential solutions and the recommended option was the installation of a booster fanor fans, to gain underground access to an already approved shaft site in the northern lease.Proposals were sought from recognised fan manufacturers and various alternative arrangements were tendered. Ultimately the choice was between one large centrifugal fan and a set (three or four) of smaller æauxiliary-likeÆ fans in parallel. The successful tender was for a single centrifugal, an arrangement very similar to the booster fans that have been operating eff ectively at Westcliff Colliery for a number of years. This paper describes the current ventilation network, evaluation of the ventilation options, the fan selection process, and the project status to date."

Jun 1, 2012

By Will S. Pettitt

Fracture Network Engineering (FNE) is the engineering design of rock mass disturbance through the use of advanced techniques to model fractured rock masses numerically, and then correlate field observations with simulated fractures generated within the models. Microseismic (MS) monitoring is a standard tool for evaluating the geometry and evolution of the fracture network induced during a hydraulic treatment, principally by source locating MS hypocenters and visualizing these with respect to the treatment volume and infrastructure (Figure 1). The integrated use of Synthetic Rock Mass (SRM) modeling of the hydrofracturing with Enhanced Microseismic Analysis (EMA) provides a feedback loop in which the SRM is constrained by the information provided by the MS data and the in-situ behavior of the fracture network is better understood, leading to informed decisions on future field operations. This paper discusses the technologies used in FNE and some of the developmental challenges we face in order to provide a more efficient and robust application of the approach. One particular challenge is the accurate representation of MS source data within the models (locations, magnitudes and mechanisms), and the ability to correlate these data effectively with field results. This challenge is being overcome by the development of more efficient numerical modeling algorithms, providing simulations in three dimensions at reservoir scale, combined with validation of these algorithms using laboratory and field case studies.

Jun 1, 2012

By J Rowland

"This paper was primarily put together in order to demonstrate what are believed to be acceptablestandards, in relation to ventilation surveys and the subsequent model assembly process. Thiswas brought about by the fact that in many parts of the world it is regarded as acceptable to carryout ventilation surveys and then build and supply the client with a æstick fi gureÆ type ventilationmodel. Such stick models have arguably litt le use and a very short life span in the real world and isalmost impossible for site staff to maintain. Thankfully most underground coal mines in Australia strive to maintain a true replica model of their ventilation circuits and to keep them in a relatively good state. Given that these mines own and maintain the models, it is often seen as necessary to update or rebuild them. The level of survey detail required to do so is totally dependent on the end use of the data and the criticality of the accuracy of the data set, to the ongoing safety and viability of the business. Mine technical personnel should think clearly about the use and importance of the ventilation survey and subsequent report outputs required that will help them bett er understand their mines and bett er prepare them to manage their ventilation circuits, on an ongoing basis. This paper provides some guidance for Australian ventilation engineers so they may plan and execute this work æin houseÆ, should they rightly choose to do so. To this end, methods of data collection and circuit analysis required for surveys of a high order of accuracy are detailed. Also, some of the issues which are important when formulating a strategy to carry out the appropriate ventilation survey for the required purpose are summarised. As well, the major details that should be furnished within any survey and some survey/report outputs and/or omissions, which are clearly not acceptable, are highlighted."

Jun 1, 2012

By Renato Macciotta

The argillaceous formation known as the Opalinus Clay is host to the Mont Terri Underground Research Laboratory. The URL was developed to investigate the hydrogeological, geochemical and geotechnical properties of the formation. Underground excavations at the site are characterized by non-elastic and time-dependent deformations. Excavations trending perpendicular to the strike of the bedding presented relatively minor deformations, however, tunnels parallel to the strike of the bedding showed much larger non-elastic deformations. This paper presents an analysis of the measured response of a tunnel trending parallel to the strike of the bedding in Opalinus Clay. The measured convergence is compared to tunnel experience in weak rocks to assess the tunnel stability.

Jun 1, 2012

By Kristine Haug

Although most in situ operations in Alberta do not encounter significant problems during resource extraction, there have been a few documented occurrences of oil or steam releases as a result of compromised caprock seals. The objective of the Oil Sands Caprock Integrity Project (OSCRIP) is to characterize the units above and below bitumen zones to determine which geological factors affect the quality of the caprock seal. In addition, geomechanical properties and stress measurements of the bitumen reservoir and overlying units will be examined to provide a better picture of the containment conditions in which in situ operations occur. The information from this study will aid regulatory staff and industry in determining the zone-specific geological and geomechanical factors that could affect the design, operation, and feasibility of in situ recovery projects. The OSCRIP study area (Townships 87 to 99 and Ranges 1 to 13, West 4th Meridian) encompasses the surface mineable area, the northeast extent of the Wabiskaw-McMurray bitumen deposit and the Clearwater Formation, as well as a wide band of the Devonian salt-dissolution zone. Regional geological mapping of the Cretaceous strata focuses on the spatial extent and thickness of the caprock seal. Mapping of the underlying Devonian strata is targeted at better understanding the potential effects of salt dissolution and collapse of overlying strata on the integrity of the caprock seal. Examination of LiDAR (Light Detection And Ranging) bare earth DEM in the study area has revealed localized depressions that may represent sinkholes rooted in subsurface collapse features in Devonian carbonate and evaporite strata. Mapping the location and understanding the timing of salt dissolution-related features and deformation in the Devonian strata will help address questions about the possible effect that geological structures, such as sinkholes, have on the integrity of the caprock, as well as the potential for localized variations in the stress regime of the bitumen zone and overlying units. The stress regime in units above 350 m is such that any induced fractures are believed to be horizontal, and therefore, there would appear to be no mechanisms that would allow these fractures to reach the surface. However, recent incidents have shown that vertical pathways can occur, linking the subsurface to the surface. The final phase of the project will evaluate the changes that may occur in the stress regime under thermal operating conditions in the study area.

Jun 1, 2012

By R Hughes

"Spring Creek Mine uses high pressure water to extract the thick Main seam in the Upper Rewanuicoal measures. The extraction method results in the creation of large voids which collapsespontaneously. This can result in the displacement of large volumes of methane, which may create a signifi cant hazard if not correctly managed. A system of automatic dilution doors is employed to mitigate this risk. This paper describes the evolution of the system and gives some examples of its eff ectiveness."

Jun 1, 2012

By Bruce Macdonald

Operational reservoir management activities such as cyclical steam, water or CO2 injections frequently cause surface micro-deformation. InSAR monitoring from space based sensors of this surface deformation has become a valuable approach to confirm and monitor extraction and injection activities. Sequestration of CO2 into deep saline aquifers is discussed as an important long term solution to slow future climate change. This method requires reliable continuous monitoring to assure that captured CO2 is sequestered in the substrate for ?all time? (typical minimum requirement by law is 20-30 years). We have shown that combining flow and deformation modeling with spaceborne synthetic aperture RADAR interferometry (InSAR) measurement of ground uplift caused by the underground release and spreading of the CO2 can be forged into a powerful tool to monitor sequestration. We used a novel InSAR approach to resolve the surface motion over the In Salah, Algeria CO2 sequestration site. Our approach exploits all information contained in an interferometric stack by exploiting both persistent distributed as well as persistent point scatterers. Displacement time series are obtained with a network inversion approach applied after topographic error and preliminary atmospheric correction of the network (dual-scale technique). After inverting the original network data to common master we then use an advanced spatio-temporal filtering scheme to remove the remaining atmospheric phase components down to scales of 1 km or less. By comparing final displacement series from multiple interleaving InSAR stacks we show that the accuracy of our refined solution to detect uplift outside of significant temporal data gaps in the InSAR stack is significantly better than 1 mm per year. We further show that accuracy and robustness to data gaps are both significantly improved by co-inverting multiple datasets with the same and different sensors. This co-inversion method also allows the seamless continuation of the monitoring from one sensor to another.

Jun 1, 2012

By Erik C. Westman

Knowledge of the orientation and relative magnitude of in-situ stresses at the mine scale is important for safe and efficient production from an underground mine. With this knowledge, stope location and scheduling can be optimized. Passive seismic tomography was used for imaging horizontal stress distribution at the mine scale. Microseismic measurements from the Creighton mine were used as input for the tomography calculations. The double-difference tomography algorithm was used, which provides the most precise results. The results clearly show a low velocity zone in the previously mined areas bounded by two high-velocity lobes located adjacent to the mined openings at locations consistent with those expected due to the horizontal stresses at the mine. The overarching goal of the research is to provide a tool that can augment both numerical modeling results and underground geotechnical measurements to allow the mine operator to produce in the safest and most efficient manner possible.

Jun 1, 2012

By D Cliff

"Recent underground coal mine incidents have again raised the issue of: under what circumstanceis it safe for personnel to re-enter the mine? Mine rescue guidelines make recommendations aboutthe limits in terms of the circumstances, lives at risk, no lives at risk and training exercises. Theseare based upon percentages of the upper and lower explosive limits. Many factors infl uencesett ing limits for safe re-entry. These include: the representativeness of the sampling location(s),the rapidity of gett ing an underground sample analysed and the rate of change of the atmospherebeing monitored. Value judgements based upon these parameters will then infl uence the sett ing ofa trigger point based upon per cent explosibility. This raises the question of how the percentage ofthe lower or upper explosive limit is established. It is easy to defi ne this when the sampling pointdata sit on the fresh air limit line. However - what value is used when the sample sits somewherein the body of an explosibility diagram? This paper explores the various options and illustratesvarious pitfalls and problems that are faced in making such a determination. These include howthe data are represented and the assumed knowledge of those doing the interpretation."

Jun 1, 2012

By A. K. Alzo?ubi

Block toppling in natural rock slopes has been under investigation since the 1970?s. De Freitas and Watters (1973) introduced the term ?toppling? to describe the movements of rock slopes by rotation in steeply dipping beds. The Lornex pit case history from British Columbia (Canada) was chosen to study the effect of mining on the stability of toppling rock slopes. A discrete element approach that allows fracturing of intact material was applied successfully to model the composite rock slide-rock topple movement. Three main movement modes were observed in the field and the numerical model; the sliding of the top of the slope exposed normal scarps, the toppling at the middle part of the slope exposed obsequent scarps facing opposite to the slope face, and dilation of the rock caused by fracturing at the toe formed loose material. The development of the rupture surface at the toe of the slope was traced and did not evolve into a continuous rupture surface throughout the slope both in the field and the numerical simulation. Good agreement was achieved between the deformations recorded in the field and the numerical simulation.

Jun 1, 2012

By Allan R. Punkkinen

Safe extraction of the valued ore resource in the deep levels of VALE Creighton Mine has progressed in a pillar-less fashion using vertical retreat, slot-slash and uppers retreat methods since the cessation of ?cut and fill? mining in the late 1980?s. Sequencing of the panel extraction and filling has been the key to successful exploitation of high stress orebodies at depth. In late 2010, discussions between the Operating Department and Creighton Ground Control revealed an opportunity to evaluate a trial primarysecondary sequence in the west end of the 400 Orebody at the 2340m horizon. To manage the trial primarysecondary project, a high level risk analysis and management of change was carried out to mitigate potential danger. As part of the requirements, an instrumentation project was conducted in the hanging wall and footwall bottomsills of the secondary panel and within the secondary panel itself. The extraction sequence was modeled with Map3D® software, confirming high stress levels with the advance of the primary panel. Enhanced ground support was installed based on modelling results. A key objective of the instrumentation project was to verify support system response to mining and to obtain knowledge in regards to the behavior of the stope. This paper describes the first time that this type of new innovative instrumented rockbolt technology had been used in a hard rock mining environment. Understanding of the physical deformation mechanisms of ground support in response to high stress conditions is the basis for an effective ground control strategy. The data played an important role in subsequent enhanced ground support system design at the mine and importantly, established the fact that the secondary pillar had not totally failed. Subsequent cavity monitor results helped establish that fact.

Jun 1, 2012

By Cheowchan Leelasukseree

Mae Moh mine, operated by Electricity Generation Authority of Thailand (EGAT), is the largest open pit mine in Southeast Asia. Its production is approximately 15 million lignite tons and 90 million m3 of waste, annually. The bottom of the final pit limit is designed to be approximately 500 m in depth. Presently, the pit depth is almost 250 m below original surface. The complexity of geological structures, such as faults, has caused a number of geotechnical difficulties. In a challenging lowwall area, called Area 4.1, an inclined weak bedding plane, G1, will be daylighted along the lowwall as following by mine plans. The dimensions of Area 4.1 are nearly 300 m wide and 90 m high. The friction and dip angles of the G1 interface are reportedly 12° and 15°, respectively. A three million m3 claystone block, resting above G1, would potentially slide down, and possibly cause a massive failure. EGAT engineers are acutely aware of the potential gigantic sliding failure and are modifying the mine plan in Area 4.1 to improve mine safety and minimize the displacement of the potential sliding block, reduce the possibility of failure and lower the additional mining cost as much as possible. The cut and fill mining technique was selected and studied to achieve those goals for mining in Area 4.1. With this mining technique, G1 will be partially daylighted. Therefore, an arch formation is induced with a sliding block above the mining area, which could perform as a temporary support undercutting a certain span. Initial studies of the behavior of the partially undercut slope are presented in this paper, along with a review of the similar failure history in Mae Moh mine and a 3-dimensional numerical model of the mine. The failure history review provides an estimation of undercut span without failure. The three-dimensional numerical model results, using 3DEC, gave an initial approximation of the displacement of the sliding block in Area 4.1. The next exciting study of the behavior of partially undercut slope is a trial undercut slope field experiment in Area 4.1. Currently, a trial undercut slope field experiment in Area 4.1 is under construction. In the field experiment, a number of monitoring programs will be installed in Area 4.1 to monitor and obtain information to allow a better understanding of the behavior.

Jun 1, 2012

By Jean-François Dorion

In an underground mine rock reinforcement elements and surface support units are often exposed to conditions that make them susceptible to corrosion. These unfavourable conditions include high relative humidity, the presence of dust and various other particles in the atmosphere, splashing of water and gases from blasting and diesel equipment. The corrosion of support systems is often associated with a loss in capacity that can be a major safety and economic concern in underground mines. A support system is composed of several components such as bolts, mesh, plate, retaining nut, cable ties. Every individual component can deteriorate due to atmospheric or aqueous corrosion and consequently can damage the integrity of the support system. This paper reports the results of a 5-yr study on the loss in capacity of individual support and reinforcement components at selected underground hard rock mines. As part of this investigation corrosion coupons were installed at selected locations at participating mines. A number of these coupons were recovered at regular time intervals and analysed for any signs of corrosion and subsequently tested to quantify any loss in capacity. The testing of the corrosion coupons was complemented by similar tests on recovered mesh and friction bolt specimens from the site. The collected data have provided useful insights on the factors that contribute to the corrosion of support systems. This knowledge can aid in the selection of appropriate support strategies and a reliable assessment of the predicted useful life of a support system and the need for rehabilitation.

Jun 1, 2012